Baumer SXC User Manual
Product Specication
36
26
36
26
36
16 x M 3 dep th 6
54
UNC 1/ 4-2 0
52
52
26
52
54
36
36
4 x M3 depth 6
26
36
26
36
16 x M3 de pt h 6
26
36
UNC 1/ 4- 20
52
SXC v2 cameras – Maximum Performance with Truesense Imaging sensors
Excellent image quality at high image rates ▪
Resolutions of 2 and 8 megapixel ▪
Frame rates up to 68 fps ▪
CameraLink ▪
®
Base for high transmission rates
Compact design (52 x 52 x 54 mm) ▪
Dimensions
Quick Start Guide
SXC v2 CameraLink® cameras with Truesense Imaging
sensors
Latest software version and technical
documentation are available at:
www.baumer.com/vision/login
Safety
Conformity:
CE, FCC Part 15 Class B, RoHS
Safety Precautions
Notice
See User´s Guide for the complete safety instructions!
Protect the sensor from dirt and ▪
moisture.
Never open the camera housing. ▪
Avoid camera contamination by ▪
foreign objects.
Environmental requirements:
Storage temp. -10°C ... +70°C
Operating temp. +5°C ... +60°C
Housing temp. max. +60°C
Humidity 10 % ... 90 %
Non-condensing
FCC – Class B device
No t e : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
support.cameras@baumer.com · Phone +49 (0)3528 4386-0 · Fax +49 (0)3528 4386-86
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany 09/13. v1.1 11099949
Camera Type
Monochrome
SXC20 v2 2/3” 1600 x 1200 68
SXC80 v2 4/3” 3296 x 2472 16
Color
SXC20c v2 2/3” 1600 x 1200 68
SXC80c v2 4/3” 3296 x 2472 16
Sensor
Size
Resolution
Installation
Full Frames
[max. fps]
Dimensions
Connect the camera using ▪
an appropriate cable to the
framegrabber board on your
PC using the sdr-26 jack on
the camera side
If required, wire the digital ▪
I/Os by using the 8 pin
connector
Connect the camera to ▪
power supply
Installation sample
1 - Framegrabber board; 2 - Camera Link®
cable; 3 - Process interface cable; 4 - Power
cable
1
4
3
8
5
7 3
1
4
2
6
2
1
T T
General Description
1
2
3
4
56
No. Description No. Description
1 (respective) lens mount 4 Digial-IO supply
2 Power Supply 5 CameraLink
3 unused 6 Signaling-LED
®
Base socket
LED Signaling
1
2
Signal Meaning
green Power on
green / yellow ashing Readout active
green Conguration command processing
red (yellow on both) Transmitting
Heat Transmission
Caution
Provide adequate dissipation of heat, to ensure that the temperatures
does not exceed +60°C (+140°F).
The surface of the camera may be hot during operation and immediately
after use. Be careful when handling the camera and avoid contact over a
longer period.
T: Housing temperature
measurement point
As there are numerous possibilities for installa-
tion, a specic method for proper heat dissipation
is not dened, but the following principles are
suggested:
Operate the cameras only in mounted condition ▪
with a good heat conductor (e.g. aluminum)
Mounting in combination with forced convection ▪
may provide proper heat dissipation
Camera Link® Interface
Notice
Only the lower CameraLink® port is used for communication. The upper port is
reserved for future use.
Caution
When xing the CameraLink® cable with too much force the screws
might get damaged.
The maximum torque is 2.5 inch lbf [0.3 Nm].
CameraLink® Base Connector
Pin Signal Pin Signal Pin Signal
1 GND 10 CC2+ 19 X3+
2 X0- 11 CC3- 20 SERTC3 X1- 12 CC4+ 21 SERTFG+
4 X2- 13 GND 22 CC1+
5 XCLK- 14 GND 23 CC26 X3- 15 X0+ 24 CC3+
7 SERTC+ 16 X1+ 25 CC48 SERTFG- 17 X2+ 26 GND
9 CC1- 18 XCLK+
Camera Link®, Process Interfaces and Power Supply
Caution
A power supply with electrical isolation is required for proper operation
of the camera. Otherwise the device may be damaged!
Power Supply Process Interface
wire colors of the connecting cable
1 (bn) Power VCC1 (wh) Out 3 5 (gr) IO Power V
3 (bu) GND 2 (bn) In 2 6 (pk) Out 1
4 (bk) NC 3 (gn) In 1 7 (bu) Out 2
4 (ye) IO GND 8 (rd) In 3
CC
Loading...