Baumatic BL555SE Instruction manual

BL555SE

Under-counter

larder fridge

USER MANUAL FOR YOUR BAUMATIC

BL555SE

Under-counter larder fridge

NOTE: This User Instruction Manual contains important

information, including safety & installation points, which will

enable you to get the most out of your appliance. Please keep it

in a safe place so that it is easily available for future reference, for
you or any person not familiar with the operation of the appliance.

JW 21/09/12

2

Contents

Environmental note 4
Important safety information 5 - 6
Specifications of your larder fridge 7
Description of the appliance 8 - 9

Description of the product features 8 - 9
Using your Baumatic fridge 9-10

Before switching on 9
During first use 10
Switching on the appliance and setting the thermostat 10

Arranging and storing food in the fridge section 11-12
Normal operating noises 12

Energy saving when using your fridge 13
Cleaning and maintenance 14-16

The defrost drain hole 14
Replacing the light bulb 15
Prolonged OFF periods 16

Installation 16-21
Electrical connection 17-18
Positioning 18
Levelling the appliance 18
Reversing the door 18-20

Troubleshooting 21-22
Baumatic consumables 23
Technical data 24
Contact details 25

3

Environmental note

Note

: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance
to prevent misuse. This should be undertaken by a
competent person. Disable the door lock to make sure that
children cannot get stuck inside the appliance.

o The packaging materials that Baumatic uses are environmentally

friendly and can be recycled.

o Please discard all packaging material with due regard for the

environment.

4

Important safety information

Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.

IMPORTANT: Any installation work must be carried
out by a qualified electrician or competent person.

Use of the appliance

o Your appliance is only designed to be used in the

home. It is suitable for storing food that needs to be
chilled and refrigerated. If it is used for any other
purpose or it is not used correctly, then Baumatic
Ltd. will accept no liability for any damage that is
caused.

o Altering the specification of the appliance must not be attempted

for reasons of safety.

Before using your appliance

o Check the appliance for any signs of transport damage. If you

notice any damage, then you should not connect your appliance
to your mains supply and should contact your retailer.

Refrigerant

o Your appliance contains R600a refrigerant, which is a natural gas

that does not contain CFCs that can damage the environment.
However it is a flammable substance, therefore care should be
taken:

 During the transportation and installation of the

appliance, make sure that the refrigeration pipe work
does not get damaged.

 If it does become damaged then sources of ignition

and open flames should be avoided. Also the room
that the appliance is situated in should be thoroughly
ventilated.

o Do not place any objects on top of the

appliance, as this may damage the table top.

5

Child safety

o Packaging material should be kept away from

children.

o Children should not be allowed to touch the

controls or play with the appliance.

General safety

o Do not pull on the power supply cable to remove the plug from

your mains supply socket.

o Do not pull out or insert the plug with wet hands.
o Do not attempt to use your appliance outdoors or

any place where it is likely to come into contact
with the elements.

o Before cleaning the appliance or performing maintenance work,

ensure that the appliance has been disconnected from your
mains supply.

o Never allow the back coils of the appliance to come into contact

with the wall surface.

o Always ensure that the location where you are installing your

appliance is free of stored items such as papers and other
flammable materials.

o Never block the ventilation openings of the appliance, either on

the inside or its exterior.

o It is vital to keep your appliance well ventilated,

so that there is proper air flow between the
bottom of the unit and the plinth/kick plate which
it is sitting on.

o Do not place electrical devices inside of the appliance, such as

mixers or ice cream makers.

Service

You should not attempt to repair the appliance
yourself, as this could cause injury or a more serious
malfunction. If you require a service call then please
contact the Baumatic Customer Care Department.

6

Specifications of your larder fridge

o Fridge gross capacity: 131 litres
o Fridge net capacity: 121 litres
o Automatic defrost
o Adjustable thermostat
o 2 x Adjustable safety glass shelves
o 1 x Salad crisper shelf (safety glass)
o 1 x Salad crisper
o 2 x General door racks
o 1 x Bottle rack
o 1 x Egg rack
o Adjustable feet
o Reversible door

Dimensions of appliance

Height: 845 mm
Width: 545 mm
Depth: 566 mm

Energy efficiency class

Energy class: A+

IMPORTANT: When you install your appliance it is important to bear
in mind its climatic rating.

In order to find out the climatic rating of your appliance, you should
check the rating plate. The rating plate is located on the front left edge
of the inside of the fridge section. You will need to open the door of
your appliance to be able to find it. The rating plate will indicate the
ambient temperature range that your appliance will function correctly
within.

7

Description of the appliance

1) Adjustable safety glass shelves

2) Salad crisper shelf (Safety glass)

3) Salad crisper

4) General door racks

5) Temperature control and internal light

6) Bottle rack

Description of the product features

1) Shelves

o The shelves may be placed in any of the guide slots within the

interior of the appliance. They are protected from sliding out.

o To remove a shelf: Take off all of the items that are stored on

the shelf that you want to remove. Then lift the front of the shelf
and carefully pull it out of the grooves.

2) Crisper drawer and cover

o The crisper drawer is in the bottom of your refrigerator and there

is a cover that goes over it.

o The cover helps to prevent fruit and vegetables from drying out

prematurely.

8

3) General door racks

o The door liner holds various shelves, which are suitable for

storing eggs, cheese, butter and yogurt. As well as smaller
packages, tubes, cans etc.

4) Bottle rack

o The lower door rack should be used for storing reasonably sized

bottles.

o IMPORTANT: IT IS IMPORTANT THAT NONE OF THE

SHELVES THAT SIT IN THE DOOR ARE OVERLOADED, AS
THIS WILL DRASTICALLY REDUCE THEIR WORKING LIFE.

Using your Baumatic fridge

Before switching on

o Make sure that it has been installed by a suitably qualified

person, as per the information contained in Baumatic’s
installation instructions.

o After delivery, wait for eight hours before connecting the

appliance to your mains supply. This will allow any refrigerant
gasses that may have been disturbed during the transportation
process to settle.

o The outside of the appliance and the removable accessories

contained within it, should be cleaned with a solution of liquid
detergent and water.

o The interior of the appliance should be cleaned

with a solution of sodium bicarbonate dissolved in
lukewarm water. The interior and accessories
should be thoroughly dried, after the cleaning
process has been completed.

o There can be an odour when you first switch on

the appliance. It will lessen as the appliance starts to cool.

9

During first use

o With dry hands, connect your appliance to your mains supply.

Set the thermostat control knob to the maximum position <7>
for a minimum of 24 hours, before positioning it to the normal
setting of <3>.

o When you first switch on the appliance, the compressor will run

more frequently for approximately 24 - 48 hours.

o During this period of time, you should try not to open the door

frequently or place a large amount of food within the appliance.

o If the unit is switched off or unplugged, you must allow at least 5

minutes before restarting the appliance on the thermostat or
reconnecting it to your mains supply.

Switching on the appliance and setting the thermostat

o You switch on your appliance by

connecting it to your mains supply and
setting the thermostat. The thermostat
dial is located on the upper right hand
side of the inside of the cabinet, next
to the interior light.

o The thermostat automatically regulates

the temperature inside the fridge. The
temperature is affected by the number
that the thermostat dial is set to.

o Position <OFF> means that the appliance will not cool.
o Position <1> will give you a higher temperature inside the

fridge.

o Position <7> will give you a lower temperature inside the fridge.
o Ideally the thermostat dial should be set to position <3>
o The fridge can maintain a temperature of between 2 – 5 degrees

centigrade.

o IMPORTANT: The ambient temperature of the room,

the temperature of food and the amount of food that
has been placed in the fridge and how often the door is
opened, will all affect the temperature being maintained
by the appliance.

10

o On the maximum setting (position <7>), your fridge will work

harder to maintain a lower temperature and will increase the
energy usage. There is no need to run your appliance on setting
<7> for prolonged periods.

o IMPORTANT: Do not run the thermostat above position <6> for

prolonged periods, otherwise the defrost drainage hole will
freeze.

Arranging and storing food in the fridge section

o Warm food or evaporating liquids should not be stored in your

refrigerator, as this will increase the humidity inside of the
appliance.

o All foods should be wrapped or covered, this is particularly

important if the food has a strong flavour. You should use
polythene bags or sheets, aluminium foil, wax paper. Liquids
should be stored in covered containers or bottles.

o To maximise the space inside of the fridge section, any excessive

packaging on the food should be removed.

o Quickly perishable food should be stored at the back of the

refrigerator, which is the coldest part of the appliance.

o No food items should be allowed to come into contact with the

back wall of the refrigerator.

o Make sure that you arrange food in such a way that the door can

close completely. Particular attention should be given to bottles
that may protrude when placed on shelves inside the main
section of the refrigerator.

o Some organic solutions, such as the oils in lemon/orange peel

and acid in butter, can cause damage to the plastic parts
contained inside of the refrigerator.

o Do not open the refrigerator door too often or leave the door

open for long periods of time, as this will increase the
temperature inside of the appliance and will increase the energy
usage.

o Meat should be wrapped in polythene bags and then placed on

the glass shelf above the salad crisper.

(Meat should only be stored in this manner for one or two
days at the most).

11

o Cold dishes/cooked food should be covered and can be placed

on any shelf.

o Fruit and vegetables should be cleaned thoroughly and placed

in the salad crisper.

o Cheese and butter should be placed in airtight containers, or

they can be wrapped in aluminium foil or polythene bags. As
much air as possible should be removed from the bags.

o Milk bottles should have a cap on them and be stored on the

bottle shelf that sits in the door.

o Garlic, potatoes, onions and bananas should only be

stored in a refrigerator IF they are kept in airtight
containers.

Normal operating noises

Ice cracking noise

o Can be heard during the automatic defrosting process.

Short cracking noise

o Can be heard when the thermostat turns the compressor on and

off.

Compressor noise

o There will be an operating noise when the compressor is running.
o After installation, the compressor may be noisier for a short

period of time.

Bubbling and burbling sound

o This noise is emitted as the coolant flows through the pipework

within the fridge.

Water flowing sound

o This is caused by water flowing into the evaporating tray during

the defrosting process and can be heard whilst the fridge is
defrosting.

12

Saving energy when using your fridge

Installing:

o Install the appliance in a cool position. If it is placed in direct

sunlight or next to an oven or other heat source, the energy
consumption can increase substantially.

o Ensure the appliance is installed with the correct ventilation

requirements. Restricting ventilation can increase the energy
consumption by 15%.

Cleaning and Maintenance:

o Occasionally clean the condenser coils (if present) at the back of

the appliance to maintain a high performance level.

o Clean the door gasket with warm water or a neutral detergent

that leaves no residue. A tight-sealing door gasket is critical to
the efficiency of your appliance.

Usage:

o Do not open the door repeatedly or more frequently than you

have to.

o Do not set the thermostat too low. A change of just one degree

can effect the energy consumption by 5%. Use a thermometer to
check the temperature.

o The refrigerator should operate at around 3 to 4 degrees Celsius.
o Allow food to sufficiently cool before putting it in the appliance

(but don’t let it sit at room temperature for too long).

o If you are going away for a long period of time, turn off the

appliance, empty and clean it and leave the door ajar.

o If you have a second appliance that is not used, make sure that

it is stored with the power off and the door left ajar until it is
actually required.

Disposing:

o If you're going to throw out your old fridge, see if there's a

chlorofluorocarbons (CFCs) recycler in your area. The
government department which looks after the environment in
your area may be able to help you.

13

Cleaning and maintenance

WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR MAINS SUPPLY BEFORE
ATTEMPTING TO CLEAN IT.

o Do not clean the appliance by pouring water onto it

or spraying water over it.

o The refrigerator compartment should be cleaned

periodically, using a solution of bicarbonate of soda
and lukewarm water.

o Clean the accessories separately with soap and water.

Do not clean them in a dishwasher.

o Do not use abrasive products, detergents or soaps.
o After washing the appliance, wipe over the area that you have

cleaned with a damp cloth and then dry it thoroughly.

o When cleaning is complete, dry your hands and then reconnect

the plug to your mains supply.

The defrost drain hole

o Defrosting occurs automatically in the refrigerator section during

operation. The defrost water is collected by the evaporating tray
and evaporates automatically.

o The drain hole should be cleaned periodically with the drain hole

cleaner. This will prevent water from collecting in the bottom of
the refrigerator, instead of flowing down the defrost drainage
channel and drain hole.

14

o IMPORTANT: Please note that the drain hole cleaner should not

be left in position permanently. Otherwise this may prevent the
defrost water from entering the drain hole.

o You can also pour a small amount of water down the drain hole

to clean the defrost drainage channel.

o You should be careful to make sure that food packages do not

touch the rear wall of the appliance, as this can interrupt the
automatic defrosting process and deflect water into the base of
the refrigerator section.

o Use a solution of bicarbonate of soda and lukewarm water to

clean the evaporating tray.

o IMPORTANT: It is normal to get some ice droplets forming on

the back wall of the appliance. The formation of ice droplets does
not indicate an appliance fault.

Replacing the light bulb

WARNING: PLEASE ENSURE THAT YOUR
APPLIANCE IS DISCONNECTED FROM
YOUR MAINS SUPPLY BEFORE
ATTEMPTING TO REPLACE THE LIGHT
BULB.

o There is an interior light next to the thermostat dial.
o Using a Phillips head screwdriver, remove the screw at the far

end of the light cover and slide the cover off.

o Change the present light bulb with a new one. The replacement

bulb should not have a greater rating than 15 W.

o Replace the light cover and after waiting five minutes, reconnect

your plug to your mains supply.

15

Prolonged OFF periods

If the fridge is not in use for a long period of time, you should:

o Disconnect the fridge from the electricity supply.
o Clean and dry the inside as instructed on page 13.
o Leave the door of the appliance open to prevent any unpleasant

smells from building up while the fridge is not in use.

Installation

IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found on the front left edge of the

inside of the refrigerator.

The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.

Electrical connection

YOUR FRIDGE IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.

We recommend that the appliance is connected by a
qualified electrician, who is a member of the N.I.C.E.I.C.

and who will comply with the I.E.E. and local regulations.

o Your refrigerator comes supplied with a 13 amp plug fitted. If in

future you need to change the fuse in this plug, then a 13 amp
ASTA approved (BS 1362) fuse must be used.

o The wiring in the mains lead is coloured as follows:

Brown Live
Blue Neutral
Green and yellow Earth

o As the colours of the wires in the appliance’s mains lead may not

correspond with the coloured markings identifying the terminals
in your spur box, please proceed as follows:

16

The brown wire must be connected to the terminal marked “L”
(live), or coloured red.

The blue wire must be connected to the terminal marked “N”
(neutral), or coloured black.

The green and yellow wire must be connected to the terminal
marked “E” (earth), or by the earth symbol, or coloured green
and yellow.

o When the connection is completed, no stray strands or cut wire

should be present. The cord clamp must be secured over the
outer sheath.

Positioning

o It is advisable that your appliance is only installed in a location

where the ambient temperature of the room, corresponds with
the climate classification that is stated on the rating plate of your
appliance. Your appliance may not function correctly if the
ambient temperature falls outside of the following ranges.

Climate classification Appropriate ambient temperature

SN +10°C to +32°C

N +16°C to +32°C

ST +18°C to +38°C

T +18°C to +43°C

o Positioning the appliance requires two people in order to avoid

injuries or damage to the appliance.

o Your appliance should not be located in direct sunlight or

exposed to continuous heat or extremes of temperature (e.g.
next to a radiator or boiler). If this is not feasible, then you
should install an insulation plate between the appliance and the
adjacent heat source.

o You should check whether there is an electrical socket available,

which will be accessible after your appliance is installed.

o Place the appliance flatly and firmly on a solid base. The

appliance is fitted with adjustable feet on the front side, which
can be used to level the appliance.

o Anything positioned above the appliance must allow sufficient

cooling of the condenser with an approximate gap of 3 cm. You
must leave a 2 cm gap to the rear of the appliance and 2 cm
either side of the appliance.

17

o If you are placing another cooling appliance next door to this

product, then there must be a gap of at least 2 cm between the
appliances. This will help to prevent condensation from forming.

o Be sure to leave enough space for the opening of the door, to

avoid damage to the appliance or personal injury.

Levelling the appliance

o If the fridge is not levelled during installation, the doors may not

close or seal properly causing cooling, frost or moisture
problems.

o To level your refrigerator you may either turn the levelling foot

clockwise to raise that side or turn it anti-clockwise to lower that
side.

IMPORTANT: It is advisable that two people carry out this
procedure. While one person adjusts the foot, the other should
push against the top of the fridge to take some weight off the
levelling foot. This makes it easier to adjust the levelling foot.

Reversing the door

IMPORTANT: BEFORE COMMENCING THE DOOR REVERSAL
PROCESS THE APPLIANCE MUST BE DISCONNECTED FROM
YOUR MAINS SUPPLY.

o We suggest that two people complete the door reversal process.
o We recommend that the door reversal process is done before the

appliance is placed in its final position.

o If food is already stored inside of it, then this must all be

removed before beginning the door reversal process.

o Retain all screws, caps and accessories that you remove for later

use.

To change the door opening direction, please follow the instructions on
the following pages:

18

1) Switch off the appliance and unplug it. Remove all contents and
shelving.

2) Tilt the appliance backwards by no more than 45°. You may find
it easier to lay the appliance on its back, however you will need
to let the appliance stand for 6 hours before turning it on should
you do this.

3) Remove the lower hinge by unscrewing the securing screws.

4) Pull the door downwards towards the bottom of the appliance,
releasing the top of the door from the top hinge-pin. Place the
door somewhere safe from damage.

5) Unscrew the two screws on the top hinge
and remove it. Re-attach the hinge to the
opposite side of the appliance.

6) Remove the hinge-pin hole cap from the top of the door and
insert it into the existing hinge-pin hole in the opposite side,
thus exposing the new hinge-pin hole and covering the old hole.

7) Unscrew the plastic hinge-pin receiver from the
bottom of the door and relocate it to the
opposite side. There are pilot groves for the
screws on the opposite side.

8) Reposition the door back onto the appliance, slotting the door
onto the hinge-pin protruding from the top of the appliance.

19

9) Install the lower hinge on the opposite side
of the bottom of the appliance/door from
which it was removed using the original
screws, completing the door reversal
procedure.

10) You can then stand the appliance back to its upright position.

IMPORTANT: Check that the door opens and shuts correctly,
without fouling, after you have completed the door reversal
process.

After the door has been reversed, you should check
the door seal of the appliance. The seal should not
be creased or crushed; otherwise there will be a gap
between it and the inside of the door.

o The seal must adhere properly all the way around the door.
o If the seal is not adhering to the cabinet properly, then you

should either:-

1. Use a warm damp cloth and manipulate the seal until it does
adhere to the cabinet properly, all the way around the door.

OR

2. Use a hair dryer on its lowest heat setting and lightly heat the
areas of the door seal that are not adhering correctly. The
heat will make the seal more pliable and this will allow you to
manipulate the seal into the correct position.

IMPORTANT: DO NOT HEAT THE DOOR SEAL ON ANYTHING BUT
THE LOWEST HEAT SETTING, OR HEAT THE SEAL FOR A LONG
PERIOD OF TIME. OTHERWISE DAMAGE MAY BE CAUSED TO
THE DOOR SEAL, WHICH WOULD NOT BE RECTIFIED UNDER
THE GUARANTEE FREE OF CHARGE.

IMPORTANT: WHEN YOU HAVE REVERSED THE DOOR OF THE
APPLIANCE. AS YOU HAVE TILTED THE APPLIANCE
BACKWARDS, YOU MUST WAIT FOR 8 HOURS BEFORE
SWITCHING THE APPLIANCE BACK ON.

20

Troubleshooting

IMPORTANT: If your fridge appears not to be
operating properly, before contacting the Baumatic
Customer Care Department, please refer to the
checklist below.

My fridge does not appear to be working/there is no
power to my appliance.

o Check that the plug is fully inserted into the power socket.
o Check that there is power to your mains supply (e.g. that there

hasn’t been a power cut or that the fuse hasn’t blown).

o Check that the thermostat inside the appliance has not been

turned to the off position.

o Check that your mains supply voltage, corresponds to the

voltage stated on the rating plate of your appliance.

My fridge appears to be performing poorly.

o Check that the appliance isn’t overloaded and that food hasn’t

been packed too tightly into it.

o The thermostat setting is too low; you should turn the

thermostat up higher.

o Ensure that the door is closing properly and that the door has

not been opened for a prolonged period in error.

o Ensure that there is adequate ventilation for your appliance.

My fridge is noisy.

o The refrigerant gas that circulates the pipe work of the appliance

may make a slight noise, even if the compressor is not running.

o If the noise worsens or the appliance gets louder than normal;

check that it is levelled off correctly, that nothing is touching the
rear of the fridge and that nothing placed inside the appliance is
rattling.

A thick ice sheet has formed on the inner back wall of
my fridge.

o Check that food has not been pushed too far back inside the

appliance, so that it is in contact with the inner back wall.

o The formation of ice droplets on the inner back wall does not

indicate a product fault.

21

There is water in the base of the fridge or leaking out
of my fridge.

o Follow “The defrost drain hole” section.

IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact the
Customer Care Department on telephone number
[phone].

DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.

The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.

This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.

Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.

IMPORTANT: Baumatic Ltd. operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.

22

Baumatic Consumables

o BC001 Degreaser for Dishwashers (200 g)
o BC002 Descaler for Washing Machines and Dishwashers (200 g)
o BC003 Ceramic Hob Cleaner (250 ml)
o BC004 Oven Cleaner (250 ml)
o BC005 Stainless Steel Cleaner and Protector (250 ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover

To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk

23

Technical Data

Manufacturer BAUMATIC LTD
Model Number BL555SE
Product Category 1 – Refrigeration
Energy Efficiency Class (1) A+
Annual Energy Consumption (2) 120 kwh
Storage Volume of Fridge
Compartment
Storage Volume of Freezer
Compartment
Star Rating
Frost Free Compartments Fridge
Temperature Rise Time
Freezing Capacity
Climate Class (3) ST
Noise Level 40 dB
Installation Type Freestanding

121 litres

(1) On a scale from A+++ (highest efficiency) to G (lowest efficiency).
(2) Annual energy consumption based on standard test results for 24

hours. The actual energy consumption will depend on how the
appliance is used and where it is located.

(3) This appliance is intended to be used at an ambient temperature
between “18°C” (lowest temperature) and “38°C” (highest
temperature).

24

United Kingdom

Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom

Sales Telephone

[phone]

Sales Fax

[phone]

Customer Care Telephone

[phone]

Customer Care Fax

[phone]

Spares Telephone

[phone]

Advice Line Telephone

[phone]

E-mail:

[e-mail]
[e-mail]
[e-mail]
[e-mail]

Website:

www.baumatic.co.uk

Facebook:

www.facebook.com/baumatic.uk

Republic of Ireland

Service Telephone

1-890 812 724

Spares Telephone

091 756 771

Czech Re

Baumatic CR spol s.r.o.
Lípovà 665
460 01 Liberec 4
Czech Republic

[phone]
www.baumatic.cz

Slovakia

Baumatic Slovakia, s.r.o.
Panenská 34
811 03 Bratislava - Staré Mesto
Slovakia

[phone]
www.baumatic.sk

Germany

Baumatic Gmbh
Bachstr.10-12
D-32 257 Bünde
Deutschland

[phone]
www.baumatic.de

Italy

Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)

[phone]
www.baumatic.it

Holland

Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland

[phone]
www.baumatic.nl

public

25

26

27

28