Page 1
Instruction manual
Make-up for your kitchen
w w w . b a u m a t i c . c o m
Page 2
Page 3
ELECTRIC
HOBS
USER AND INSTALLATION
INSTRUCTIONS
Page 4
For future reference please record the following information which can be
found on the Rating Plate and the date of purchase which can be found in the
invoice:
Model Number .
Serial Number .
Date of Purchase .
TECHNICAL DATA
ELECTRICAL DETAILS
Rated Voltage: 230V ac 50Hz
Supply Connection: Switched Double-pole Isolator with 3mm contact separation
POWER INPUTS AND PROTECTION RATING
Model Max Total Min Fuse
kW Amps Protection Rating
B65 6.0 26.1 30A
BE2SS 3.5 15.2 16A
BVC2SS 2.9 12.6 16A
Mains Supply Connection Cable: 3 x 2.5mm2 Type H05 RR-F <HAR> marked
NOTE:
For cable connection details, see diagram on appliance base plate.
2
Page 5
CONTENTS
General Information page 4
Warning and Safety Instructions page 5
Instructions for Use pages 6 —
7
Instructions for Installation Pages 8 — 1
0
Technical Data Page 11
Conditions of Guarantee Back cover
3
Page 6
GENERAL INFORMATION
Please read this booklet thoroughly before you use this appliance. It is important that you
understand all the control functions before commencing to cook with your Baumatic appliance.
Please remember the advice and warnings shown on page 5 which is headed
IMPORTANT — Warning and Safety Instructions .
This appliance is designed for domestic household use when built into kitchen worktop.
NOTE: The housing, adjacent furniture and all materials used in the installation must be able to
withstand a minimum temperature rise of 85°C above ambient during periods of operation. This
information is for guidance only and the actual withstand temperature will depend on the
performance rating for the surface finish of the worktop.
Certain types of kitchen furniture surface finishes are particularly prone to heat damage or
discolouration at temperatures lower than the above guidelines.
Installing the appliance in contravention of the guidance given will be at the liability of the
owner.
The use for any other purpose or in any other environment without the express agreement of
Baumatic Ltd, would invalidate any warrantee or liability claim.
Your new appliance is guaranteed against electrical or mechanical defects subject to certain
exclusions noted in Baumatic Ltd Conditions of Guarantee.
The aforegoing does not affect your statutory rights.
The Warrantee applies to Great Britain and Northern Ireland only.
In the event that you require any After Sales Service or advice, please contact the Baumatic
Service Department on telephone number — 0118 933 6911.
Before using this appliance ensure that any protective packaging or coatings have been removed.
To aid the protection of the environment, please sort the packing materials into different types
and dispose of them in accordance with the local waste disposal laws.
Any further information on waste disposal can be obtained from your local Environment Agency office.
When first used, an odour may be emitted by any residual protective finish or moisture, which
will cease after a short period of time.
This appliance has been constructed and distributed in compliance with the essential requirements
of the following EEC DIRECTIVES and EUROPEAN NORMS:
CE Marking — 93/68 Low Voltage — 73/23 EMC — 89/336
Materials that can touch food — 89/109.
Safety Standards — EN 60 335-1, EN 60 335 — 2 — 6.
As Baumatic have a policy of continued product improvement, the right is reserved to adjust and
make any modifications deemed necessary without notification.
INSTALLATION INSTRUCTIONS
9
INSTALLATION NOTES
1 Cut the aperture to the dimensions shown in the table below or use the template provided on
the packaging.
2 Invert the hob and apply the sealing agent provided to match the outer perimeter edge.
3 If the sealing agent is a strip type, the protective covering must be removed from both sides.
Do not leave a gap in the sealing agent or overlap the thickness.
NOTE: do not use any Silicone based sealant, as this can damage the worktop surface if
repairs are required.
4 Insert the appliance into the aperture and fix into position via the clamps & screws, tightening
the screws evenly (see Fig.3).
Fig.3
HOB APERTURE DIMENSIONS
MODEL A B C D E
B65
500
585 480
560
30
BE2SS
510
290 480
285
30
BV2SS
510
290 490
270
40
4
Page 7
IMPORTANT NOTE — WARNING and SAFETY INSTRUCTIONS
This appliance complies with all current European safety legislation, however Baumatic do wish
to emphasise that compliance does not remove the fact that surfaces will become hot during use
and retain heat after operation.
Baumatic therefore strongly advise that babies and young children are prevented from being near
or touching the appliance at any time.
If it is necessary for younger family members to be in the kitchen, please ensure that they are kept
under close supervision at all times.
We also advise that great care is taken during use and cleaning operations.
Do make sure that the pan handles are always correctly positioned to avoid accidental contact.
Do not leave heated oil or fat unattended as there is a risk of fire.
Do use pans that are flat bottomed and the correct size for the heating area to be used (never smaller).
Do not allow electrical fittings or cables to be in contact with hot areas of the appliance.
Do not use the appliance for space heating or to dry clothes.
Do not install the appliance next to curtains or soft furnishings.
NOTE: This appliance must be correctly installed by a suitably qualified person, strictly in
accordance with the manufacturer s instructions. For gas installations, the Installer must be Corgi
registered (all Baumatic Engineers are Corgi registered) and for electrical installations, NICEIC
registration is recommended.
Baumatic Ltd declines any responsibility for injury or damage to persons or property as a result of
improper use or installation of this appliance.
Heat, steam and moisture will be created during use, take care to avoid injury and ensure
that the room is adequately ventilated. If prolonged use occurs, additional ventilation may
be required — please consult your Qualified Installer if you are in any doubt about the
amount required.
5
Page 8
USER INSTRUCTIONS
INSTRUCTIONS FOR USE
These User Instructions should be retained for future reference and for use by a person who is
perhaps unfamiliar with the appliance.
The following models are covered by these instructions:
B65 BE2SS BVC2SS
USING ELECTRIC HOTPLATES
The symbols on the Control Panel fascias show which hotplate the control system operates. A
pilot light indicates when a hotplate is switched on.
B65-BE2SS-BVC2SS
When using an electric hotplate for the first time or after a long period of disuse, turn the knob to
1 and let it heat for about 20 minutes to eliminate any possible moisture absorbed by the internal
insulating material.
- Dry the bottom of the pan before placing it on the hotplate.
- Turn the hotplate on only after placing the pan on it.
The hotplates are controlled by a 7 positions knob (from 1 to 6 . Turn the knob anti-clockwise
to the desired setting. A warning light on the control panel will inform you if the plate is on or
off.
Suggested settings (guide):
Position Heat intensity Use
0 Off
1 Very slow For melting butter,chocolate etc.For heating small amounts of liquid
2 Low For heating larger amounts of liquid .For preparing slow-cooking creams and
sauces
3 Medium-low For thawing frozen foods and cooking stews,cooking at boiling or lower
temperatures
4 medium For boiling foods,roasting delicate meats and fish
5 High For braising chops and steaks, for large meats soups.
6 Very high For boiling large amounts of water and frying
ENERGY SAVING TIPS
The diameter of the saucepan must be the same or slightly larger than that of the electric hotplate.
Never use a pan which is smaller than the electric hotplate.
-Use flat-bottomed pans only.
-Preferaby cover pans with a lid to permit cooking at a lower heat.
-Always cook vegetables and potatoes etc. in as little watwr to reduce cooking times.
USING CERAMIC ZONES
On model BVC2SS, each cooking zone has a corresponding Residual Heat Indicator neon (to be
found at the front of the hob on the right hand side). The neon will light up when the
corresponding cooking zone becomes hot, and will remain lit until the temperature on the cooking
zone has dropped below 50°C.
USER INSTRUCTIONS
7
WARNING
• Do not use commercial simmering aids as these can create excessive heat that can damage the
appliance.
• Do not use the glass ceramic surface of the hob as a griddle.
• Do not leave hotplates on without a pan or an empty pan.
• Be aware that hotplates will retain heat whilst cooling down.
• When cooking foods with high sugar content, ensure that any spillage is removed
immediately to avoid damage to the ceramic surface.
HELPFUL HINTS
• Always use the correct diameter pan, one that is the same or slightly larger than the hotplate.
• The bottom of the pan must be flat.
• Whenever possible keep the lid on the pan when cooking.
• Avoid over-spill of liquid by reducing the heat when boiling has occurred.
CLEANING THE APPLIANCE
Always allow the appliance to cool down before cleaning to avoid a burn injury.
ELECTRIC HOTPLATES
The hotplates should be lightly greased with oil (using a soft cloth). This will ensure that the
surface remains clean and will also prevent formation of rust.
CERAMIC ZONES
Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the
surface finish.
Normally, wiping with a soft cloth dampened with hot detergent and drying with a soft cloth is
sufficient but for stubborn marks the following is recommended:
Vitreous Enamel or Stainless Steel parts — use only a cleaner that is recommended for these
types of material — avoid chloride based products (such as bleach).
Glass Ceramic surfaces — if any spillage becomes burnt on, remove with a ceramic glass cleaner
or scraper and clean with a cleaner-conditioner containing silicone.
Do not allow the ceramic glass surface to become scratched or damaged as this could lead to
a hazard.
6
Page 9
USER INSTRUCTIONS
WARNING
• Do not use commercial simmering aids as these can create excessive heat that can damage the
appliance.
• Do not use the glass ceramic surface of the hob as a griddle.
• Do not leave hotplates on without a pan or an empty pan.
• Be aware that hotplates will retain heat whilst cooling down.
• When cooking foods with high sugar content, ensure that any spillage is removed
immediately to avoid damage to the ceramic surface.
HELPFUL HINTS
• Always use the correct diameter pan, one that is the same or slightly larger than the hotplate.
• The bottom of the pan must be flat.
• Whenever possible keep the lid on the pan when cooking.
• Avoid over-spill of liquid by reducing the heat when boiling has occurred.
CLEANING THE APPLIANCE
Always allow the appliance to cool down before cleaning to avoid a burn injury.
ELECTRIC HOTPLATES
The hotplates should be lightly greased with oil (using a soft cloth). This will ensure that the
surface remains clean and will also prevent formation of rust.
CERAMIC ZONES
Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the
surface finish.
Normally, wiping with a soft cloth dampened with hot detergent and drying with a soft cloth is
sufficient but for stubborn marks the following is recommended:
Vitreous Enamel or Stainless Steel parts — use only a cleaner that is recommended for these
types of material — avoid chloride based products (such as bleach).
Glass Ceramic surfaces — if any spillage becomes burnt on, remove with a ceramic glass cleaner
or scraper and clean with a cleaner-conditioner containing silicone.
Do not allow the ceramic glass surface to become scratched or damaged as this could lead to
a hazard.
7
Page 10
INSTALLATION INSTRUCTIONS
INSTRUCTIONS FOR INSTALLATION
This appliance must be installed by a competent person in accordance with the current version of
the following UK Regulations and Safety Standards or their European Norm replacements:
Building Regulations (issued by the Department of Environment)
Building Standards (issued by the Scottish Development Department)
IEE Wiring Regulations
Electricity at Work Regulations
Baumatic Ltd Installation Instructions
POSITIONING THE APPLIANCE
This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending
on size) or 600mm worktop, providing the following minimum distance is allowed:
- 650mm between the top surface and the underside of any horizontal surface above it.
- 50mm clearance around the appliance and any combustible materials.
The surface of any adjacent unit must be capable of withstanding a minimum temperature rise of
85°C.
PRE-COMMISSIONING THE APPLIANCE
When unpacked, check that the following parts are included with the appliance:
• Baumatic Ltd Instruction and Installation Book
• Adhesive sealing agent and fixing clamps & screws
5
IMPORTANT NOTE — WARNING and SAFETY INSTRUCTIONS
This appliance complies with all current European safety legislation, however Baumatic do wish
to emphasise that compliance does not remove the fact that surfaces will become hot during use
and retain heat after operation.
Baumatic therefore strongly advise that babies and young children are prevented from being near
or touching the appliance at any time.
If it is necessary for younger family members to be in the kitchen, please ensure that they are kept
under close supervision at all times.
We also advise that great care is taken during use and cleaning operations.
Do make sure that the pan handles are always correctly positioned to avoid accidental contact.
Do not leave heated oil or fat unattended as there is a risk of fire.
Do use pans that are flat bottomed and the correct size for the heating area to be used (never smaller).
Do not allow electrical fittings or cables to be in contact with hot areas of the appliance.
Do not use the appliance for space heating or to dry clothes.
Do not install the appliance next to curtains or soft furnishings.
NOTE: This appliance must be correctly installed by a suitably qualified person, strictly in
accordance with the manufacturer s instructions. For gas installations, the Installer must be Corgi
registered (all Baumatic Engineers are Corgi registered) and for electrical installations, NICEIC
registration is recommended.
Baumatic Ltd declines any responsibility for injury or damage to persons or property as a result of
improper use or installation of this appliance.
Heat, steam and moisture will be created during use, take care to avoid injury and ensure
that the room is adequately ventilated. If prolonged use occurs, additional ventilation may
be required — please consult your Qualified Installer if you are in any doubt about the
amount required.
8
Page 11
INSTALLATION INSTRUCTIONS
INSTALLATION NOTES
1 Cut the aperture to the dimensions shown in the table below or use the template provided on
the packaging.
2 Invert the hob and apply the sealing agent provided to match the outer perimeter edge.
3 If the sealing agent is a strip type, the protective covering must be removed from both sides.
Do not leave a gap in the sealing agent or overlap the thickness.
NOTE: do not use any Silicone based sealant, as this can damage the worktop surface if
repairs are required.
4 Insert the appliance into the aperture and fix into position via the clamps & screws, tightening
the screws evenly (see Fig.3).
Fig.3
HOB APERTURE DIMENSIONS
MODEL A B C D E
B65
500
585 480
560
30
BE2SS
510
290 480
285
30
BV2SS
510
290 490
270
40
A
B
C
D
Model A B C D E
B65 500 585 560 480
40
BE2SS 288 510 268 490 40
BV2SS 288 510 268 490 40
9
Page 12
INSTALLATION INSTRUCTIONS
ELECTRICAL CONNECTION
This appliance must be installed by a competent person, such as one holding NICEIC Registration
and in accordance with the latest edition of the IEE WIRING Regulations.
Before connecting the appliance, make sure that the supply voltage marked on the rating Plate
corresponds with the mains supply voltage.
WARNING — THIS APPLIANCE MUST BE EARTHED
Depending on the Power Input of the model to be installed, connection will require a 16Amp or
30Amp protected supply using a switched double pole isolating unit having a minimum 3mm
contact separation and a BS6007 3-core cable (see Technical Data at page 11 for full
information).
Care must be taken to avoid the cable being in contact with hot parts of the appliance.
The isolating unit should be placed in an easily accessible position adjacent to the appliance.
NOTE
The appliance must not be connected to the mains supply by means of a 13A plug and
socket.
MAINTENANCE
During the guarantee period, in case of need all service intervention should be referred
back to the Baumatic Ltd Service department. Please note that intervention or repair by
any unauthorised personnel will invalidate such guarantee.
3
CONTENTS
General Information page 4
Warning and Safety Instructions page 5
Instructions for Use pages 6 —
7
Instructions for Installation Pages 8 — 1
0
Technical Data Page 11
Conditions of Guarantee Back cover
10
Page 13
TECHNICAL DATA
ELECTRICAL DETAILS
Rated Voltage: 230V ac 50Hz
Supply Connection: Switched Double-pole Isolator with 3mm contact separation
POWER INPUTS AND PROTECTION RATING
Model Max Total Min Fuse
kW Amps Protection Rating
B65 6.0 26.1 30A
BE2SS 3.5 15.2 16A
BVC2SS 2.9 12.6 16A
Mains Supply Connection Cable: 3 x 2.5mm2 Type H05 RR-F <HAR> marked
NOTE:
For cable connection details, see diagram on appliance base plate.
Once the electrical cable has been located into the correct terminals ensure that the brass links are in
place and that all screws in the terminal block are secured by tightening each screw to create the link
11
Page 14
BAUMATIC Ltd
CONDITIONS OF GUARANTEE
Dear Customer,
Included with your new Baumatic appliance is a guarantee registration card, please complete this
and return and your earliest convenience.
This guarantee is in addition to your statutory legal rights and will not in any way hinder
any legal rights.
The conditions of the guarantee, which applies, to your Baumatic appliance are as follows:
All Work in relation to the Guarantee must be carried out by Baumatic Ltd or an approved
service agent of Baumatic Ltd. Any claims made under the terms of the guarantee must be
supported by the original invoice / bill of sale issued at the time of purchase.
The guarantee period starts from the date of the original purchase and the manufacturer will
provide the parts and labour required to repair the appliance should breakdown occur as a result
of mechanical / electrical failure. This service will be given Free of charge within the Guarantee
period. An additional Insurance scheme is available should you wish to extend the warranty
period.
This guarantee applies to UK mainland and Northern Ireland only.
THIS GUARANTEE DOES NOT COVER:
• Any damage caused by transit, misuse, or neglect.
• Cosmetic and perishable parts: plugs, fuses, light bulbs, light covers, cosmetic trims, cables,
filters and attachments, knobs, any rubber and seals, ceramic or glass surfaces, dents,
scratches, paintwork.
• Attachments / Accessories, trivets and handles, griddles, pan stands, shelves, burner caps and
collars, oven liners. Plus any additions thereafter.
• Periodic maintenance, the repair or replacement of parts due to natural wear and tear.
• Material discoloration, corrosion.
• Incorrect installations, modifications or repair by any unauthorised personnel.
• Use of non-Baumatic parts.
• Damage caused by foreign objects or substances.
• Appliances used for non-domestic use.
• Operation on unsuitable voltage, water or gas supplies.
• Accidents, Civil war, acts of God or any cause beyond the control of Baumatic Ltd.
PLEASE NOTE ALL GUARANTEES ARE NON TRANSFERABLE
SALES SERVICE SPARES
TEL 0118 933 6900 TEL 0118 933 6911 TEL 0118 933 6922
FAX 0118 931 0035 TEL 0118 986 9124
For further information or any other query you may have please contact one of the above
numbers.
Thank you for buying Baumatic.
GB
1
ELECTRIC HOBS
USER AND INSTALLATION
INSTRUCTIONS
12
Page 15
Page 16
Page 17
Page 18
H01A004
Page 19
Page 20
Make-up for your kitchen
Loading...