BAUMATIC B44SS User Manual

Download

Page 1

Instruction manual

B44SS 4 Burner gas hob

Page 2

Page 3

GAS HOBS

USER AND INSTALLATION

INSTRUCTIONS

HT Mod 05/07/06

Page 4

For future reference please record the following information which can be found on the Rating Plate and the date of purchase which can be found in the invoice:

Model Number …………………….

Serial Number …………………….

Date of Purchase …………………….

Page 5

CONTENTS

General Information

Warning and Safety Instructions

Instructions for Use

Instructions for Installation

Technical Data

Conditions of Guarantee

page 4

page 5

pages 6–7

Pages 8–12

Pages 12–1

Back cover

Page 6

GENERAL INFORMATION

Please read this booklet thoroughly before you use this appliance. It is important that you understand all the control functions before commencing to cook with your Baumatic appliance.

Please remember the advice and warnings shown on page 5, which is headed ‘IMPORTANT – Warning and Safety Instructions’.

This appliance is designed for domestic household use when built into a kitchen worktop. NOTE: The housing, adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature rise of 85qC above ambient during periods of operation. This information is for guidance only and the actual withstand temperature will depend on the performance rating for the surface finish of the worktop. Certain types of kitchen furniture surface finishes are particularly prone to heat damage or discolouration at temperatures lower than the above guidelines. Installing the appliance in contravention of the guidance given, will be at the liability of the owner.

For use in Leisure Accommodation Vehicles, notice must be taken of the appropriate statement in the Installation Instructions (see page 9 – Important Note 5).

The use for any other purpose or in any other environment without the express agreement of Baumatic Ltd, would invalidate any warrantee or liability claim

Your new appliance is guaranteed against electrical or mechanical defects subject to certain exclusions noted in Baumatic Ltd Conditions of Guarantee. The aforegoing does not affect your statutory rights.

The Warrantee applies to Great Britain and Northern Ireland only. In the event that you require any After Sales Service or advice, please contact the Baumatic Service Department on telephone number – 0118 933 6911.

Before using this appliance ensure that any protective packaging or coatings have been removed. To aid the protection of the environment, please sort the packing materials into different types and dispose of them in accordance with the local waste disposal laws. Any further information can be obtained from your local Environment Agency office. When first used, an odour may be emitted by any residual protective finish or moisture, which will cease after a short period of time.

This appliance has been constructed and distributed in compliance with the essential requirements of the following EEC DIRECTIVES and EUROPEAN NORMS :-

CE Marking – 93/68 Low Voltage – 73/23 Gas Products – 90/396 EMC – 89/336 Materials that can touch food – 89/109. Safety Standards – EN 60 335-1, EN 60 335 – 2 – 6, EN 30-1-1.

As Baumatic have a policy of continued product improvement, the right is reserved to adjust and make any modifications deemed necessary without notification.

Page 7

IMPORTANT NOTE – WARNING and SAFETY INSTRUCTIONS

This appliance complies with all current European safety legislation, however Baumatic do wish to emphasise that compliance does not remove the fact that surfaces will become hot during use and retain heat after operation.

Baumatic therefore strongly advise that babies and young children are prevented from being near or touching the appliance at any time. If it is necessary for younger family members to be in the kitchen, that they are kept under close supervision at all times. We also advise that great care is taken during use and cleaning operations.

Do make sure that the pan handles are always correctly positioned to avoid accidental contact.

Do not leave heated oil or fat unattended as there is a risk of fire.

Do use pans that are flat bottomed and the correct size for the heating area to be used (never smaller).

Do not allow electrical fittings or cables to be in contact with hot areas of the appliance.

Do not use the appliance for space heating or to dry clothes.

Do not install the appliance next to curtains or soft furnishings.

NOTE: This appliance must be correctly installed by a suitably qualified person, strictly in accordance with the manufacturer’s instructions. For gas installations, the Installer must be Corgi registered (all Baumatic Engineers are Corgi registered) and for electrical installations, NICEIC registration is recommended.

Baumatic Ltd declines any responsibility for injury or damage to persons or property as a result of improper use or installation of this appliance.

Heat, steam and moisture will be created during use, take care to avoid injury and ensure that the room is adequately ventilated. If prolonged use occurs, additional ventilation may be required – please consult your Qualified Installer if you are in any doubt about the amount required.

Page 8

USER INSTRUCTIONS

INSTRUCTIONS FOR USE

These User Instructions should be retained for future reference and for use by a person who is perhaps unfamiliar with the appliance.

The following models are covered by these instructions:

B60 B68 B61 B62 BT62 B64 B67

USING THE HOB

The symbols on the Control Panel fascias show which burner the Control Knob operates. Dependent on the mo

1. Auto Ignition After pressing in and turning the appropriate knob anti-clockwise to the large flame symbol, the ignition spark will operate as long as the knob is pressed down.

When a flame has been established the knob can be released.

2. Manual Ignition After pressing in and turning the appropriate knob anti symbol, press the ignition button located on the control panel.

The ignition spark will operate as long as the button is held down. When a flame has

been established, release the button. To regulate the flame, continue turning anti

and small flame symbols. To turn the burner off, turn fully clockwise.

NOTE:

B69 B16.5 B17.7 B16.6 BG2 BWK1

del there are two methods for igniting the burners.

B17.5 B17.6

PG2 PWK1 P62

-clockwise to the required setting between the large

P68 P75 P90 PF75 B44 B46

-clockwise to the large flame

C45 BF45 AS24 AS25

When a Thermocouple Safety Device is incorporated in the appliance, it is necessary for the knob to be continuously held down for a further period of approximately 10 seconds after the flame has been The Safety Device is designed to stop the flow of gas to the burner head in the event of a flame out situation.

Please note that this appliance carries the for the marine environment.

established to enable the thermocouple to function.

mark for normal domestic use and is not suit

able

Page 9

USER INSTRUCTIONS

HELPFUL HINTS

Always use the correct diameter pan, one that is the same or slightly larger than the flame ring. The flame should never exceed the diameter of the pan. For model PF75 please make sure you comply with maximum pans' diameters allowed as showed in the picture:

The bottom of the pan should be flat and wherever possible, keep the lid on the pan when cooking.

Depending on the model the following burners are provided: Large (Rapid or Triple Crown) – for rapid cooking or boiling large quantities of liquid Wok – for rapid cooking or boiling large quantities of liquid Medium (Semi-rapid) – for general cooking Small (Auxiliary)– for slow or simmer cooking Fish Kettle – for specialised cooking

All burners are variable between full and low positions

WARNING

Do not use commercial simmering aids as these can create excessive heat, which can damage the appliance.

CLEANING THE APPLIANCE

Always allow the appliance to cool down before cleaning to avoid a burn injury.

Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the surface finishes.

Normally, wiping with a soft cloth dampened with hot detergent solution is sufficient but for stubborn marks the following is recommended:

Vitreous Enamel parts – use only a cleaner that is recommended for this type of material.

Burner Assemblies – remove from the hob and soak for about 10 minutes in hot detergent solution. Rinse off and dry checking that the burner holes are not clogged, then reassemble in the correct order.

Page 10

INSTALLATION INSTRUCTIONS

INSTRUCTIONS FOR INSTALLATION

This appliance must be installed by a competent person in accordance with the current version of the following UK Regulations and Safety Standards or their European Norm Replacements:

: UK law stipulates that gas appliances must be installed and repaired by a CORGI

NOTE

Registered Installer (all Baumatic Engineers are CORGI Registered).

Gas safety Regulations (Installation & Use) Building Regulations (issued by the Department of Environment) Building Standards (Issued by the Scottish Development Department) IEE Wiring Regulations Electricity at Work Regulations BS 6172 Installation of Domestic Gas Cooking Appliances (if necessary, BS 5482 Installation of Domestic LPG Appliances) BS 5440 Installation of Flues and Ventilation for Gas Appliances Baumatic Ltd Installation Instructions

POSITIONING THE APPLIANCE

This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending on size) or 600mm wide worktop, providing the following minimum distance is allowed:

- 700mm between the top surface and the underside of any horizontal surface above it.

- 50mm clearance around the appliance and combustible materials. The surface finish of any adjacent unit must be capable of withstanding a minimum temperature of 85qC.

PRE-COMMISSIONING THE APPLIANCE

When unpacked, check that the following parts are included with the appliance:-

x Baumatic Ltd Instruction and Installation Book x Pan Supports x Burner Assemblies x Adhesive sealing strip and fixing clamps & screws x ½ BSP Elbow & Seal

LPG conversion kit comprising an LPG jet for each burner and a self-adhesive label for

x

amending Gas Category on the appliance Rating Label.

Page 11

INSTALLATION INSTRUCTIONS

INSTALLATION NOTES

1. Cut the aperture to the dimensions shown below or use the template if printed on the packaging.

2. Invert the Hob and apply the sealing agent provided to match the outer perimeter edge.

3. If t

he sealing agent is a strip type, the protective covering must be removed from both sides. Do not leave a gap in the sealing agent or overlap the thickness.

NOTE

: do not use any Silicone based sealant, as this can damage the worktop su

if repairs are required.

4. Insert the appliance into the aperture and fix in position via the clamps & screws, tightening the screws evenly (see Fig. 1 below).

5. If the appliance is to be installed in a Leisure Accommodation V requirements of N 721 must be applied.

ehicle, the

rface

HOB APERTURE DIMENSIONS

Model

B60 B61 B62

BT62

B67 B68

B69 B16.5 B16.6

BG2

BWK1

B17.5 B17.6 B17.7

PG2

PWK1

P62

P68

P75

P90

PF75

B44

B46 BC45 BF45 AS24 AS25

ABCDE

595 500 560 480 595 500 560 480 595 510 560 480 595 510 560 480 685 510 560 480 685 510 560 480 685 510 560 480 860 510 830 480 860 510 830 480 288 510 490 268 288 510 490 268 860 510 830 480 860 510 830 480 860 510 830 480 288 510 285 480 288 510 490 268 585 500 560 480 685 500 560 480 740 500 560 480 860 510 830 480 740 500 700 480 600 510 560 480 600 510 560 480 600 510 560

480 600 510 560 480 595 510 560 480 740 510 560 480

Fig.1

30 30 30 30 30 30 30 30 30

30 30 30 30

30 30 30 30 30 30 30 30 30 30 30

Page 12

INSTALLATION INSTRUCTIONS

VENTILATION OF ROOMS

The actual ventilation requirements must be determined by reference to the Statutory

Regulations in force.

GAS CONNECTION

With one exception these appliances must be connected to the gas supply by use of the ½ BSP Elbow, seal and copper pipe and an isolation tap fitted in an easily accessible position. The one exception to the above is for the BT62 Hob unit when installed into the CK5 Cooking centre for which connection to the gas supply must be made via a flexible hose in compliance of BS6172.

This appliance as supplied is for use with Natural Gas, if it is to be adapted for LPG proceed as follows:

1. Isolate the appliance from the electricity and gas supplies.

2. Remove the pan supports and burner assemblies.

3. Replace the injectors with the alternative LPG injectors, supplied.

4. Use the appropriate thread sealant and check for gas soundness.

5. Affix the self-adhesive label to the rating plate to amend the Gas Category details.

Fig. 2 Fig. 3

Page 13

In order to adjust the minimum gas flow proceed as follows:

x Ignite the burner and turn down to the minimum setting.

x Remove the control Knob from the gas tap. x Adjust the flow either clockwise to decrease or anti-clockwise to increase the flame. Use a

screwdriver inserted down the gas tap rod or via the screw head adjacent to the rod for models fitted with a Flame Supervision Device.

x Check that the flame is 3-4 mm in length, bluish in colour, stable and noiseless, and does not

extinguish when changing from maximum to minimum flow.

x Replace the control knob and check that all components have been reassembled correctly.

INSTALLATION INSTRUCTIONS

ELECTRICAL CONNECTION

Before connecting the appliance, make sure the supply voltage marked on the rating Plate corresponds with the mains supply voltage.

WARNING – THIS APPLIANCE MUST BE EARTHED

This appliance should be wired into a double pole Switched Fused Spur Outlet having 3 mm contact separation and the fuse rating reduced to 3 Amps.

IMPORTANT

The wires in the main supply lead are coloured in accordance with the following code:Green and Yellow – Earth Blue – Neutral Brown – Live

The connections must be made as follows:The wire coloured Green and Yellow must be connected to the terminal marked ‘E’ or the earth symbol (.) or coloured green and yellow. The wire coloured Blue must be connected to the terminal marked ‘N’ or coloured blue or Black. The wire coloured Brown must be connected to the terminal marked ‘L’ or coloured brown or red. NOTE: The terminals marked ‘SUPPLY’ are for the mains supply wires and the terminations marked ‘LOAD’ are for the appliance wires.

The electrical outlet is to be positioned in an easily accessible position adjacent to the appliance. In the event that it is necessary to replace the mains supply lead, the replacement must conform to the specification listed in the Technical Data. Ensure that the colour code connection is correct and that all screws are tightened correctly.

Page 14

INSTALLATION INSTRUCTIONS

MAINTENANCE

During the guarantee period, in case of need all service intervention should be referred back to the Baumatic Ltd Service department. Please note that intervention or repair by any unauthorised personnel will invalidate such guarantee,

Before carrying out any maintenance, disconnect the appliance from the gas and electricity supplies.

If a gas tap becomes stiff to operate, proceed as follows:

x Remove the control knobs, pan supports, burners and hob fixing screws & clamps. x Remove the Hob from the worktop and remove any underside protective covers. x Disconnect the fixings holding the tap to the fascia panel, separate the assembly, then clean

the cone and seating with a cloth dampened with solvent.

x Lightly smear the cone with high temperature grease, reassemble into position and rotate a

few times. Remove the cone again and remove any excess grease making sure that the gas ducts are not obstructed with grease.

x Carefully reassemble the components and check for gas soundness.

If it becomes necessary to replace the gas tap, proceed as follows:

x Disconnect the appliance as described above. x Disconnect the gas pipe from the gas tap, disassemble from the gas rail by removing the

fixing screws.

x When fitting a new tap, ensure that a new gasket is used. x Re-connect the gas tap, check for gas soundness and reassemble the hob.

TECHNICAL DATA

ELECTRICAL DETAILS

Rated Voltage 230V ac 50Hz Supply Connection 13A (double pole switched fused outlet with 3mm contact gap) Power Input 0.008 to 0.02kW (depending on model) Mains supply lead 3 x 0.75mm2 Type RR-F HAR! marked

GAS DETAILS

Connection Rp ½ (ISO R7) Type Natural Gas (20.9 mbar) – alternative LPG G30 (28-30 mbar)

[Town Gas G110 – 120 (8 mbar) to order]

Page 15

BURNER TYPES AND POWER INPUTS : kW

Model

B60 B61 B62 BT62 B67 B68 B69 B16.5 3.0/0.75 B16.6 3.0/0.75 BG2 BWK1 B17.5 3.0/0.75 B17.6 3.0/0.75 B17.7 PG2 PWK1 P62 P68 P75 P90 PF75 B44 BC45 BF45 B46 AS24 AS25

Large

Max/Min Max/Min Max/Min Max/Min Max/Min Max

3.0/0.75

---

3.0/0.75

---

3.0/0.75

Medium

1.75/0.44

Small

1.0/0.3

1.0/0.3 3.3/1.5

1.0/0.3

1.0/0.3 3.3/1.5

1.0/0.3

1.0/0.3 3.3/1.5 2.9/1.5

1.0/0.3

1.0/0.3 3.3/1.5

1.0/0.3 3.8/1.5

1.0/0.3 4.2/0.3

1.0/0.3

1.0/0.3 3.8/1.5

Wok

- - 7.50

- - 4.00

3.3/1.5

- - 4.00

4.2/0.3

- - 7.50

Fish

- 7.80

- 3.30

- 4.20

- 7.80

Total

10.80

12.25

10.80

12.25

10.70

11.30

11.70

9.70

7.50

11.30

Page 16

JET SIZING CONVERSION TABLE: NATURAL GAS / LPG

Model

B60 B61 B62 BT62 B67 B68 B69 B16.5 B16.6 BG2 BWK1 B17.5 B17.6 B17.7 PG2 PWK1 P62 P68 P75 P90 PF75 B44 BC45 BF45 B46 AS24 AS25

Large

Medium

Small

Wok

Fish

NG/LPG NG/LPG NG/LPG NG/LPG NG/LPG

1.15/0.85 0.97/0.65 0.72/0.50

1.15/0.85 0.97/0.65 0.72/0.50 1.24/0.91

1.15/0.85 0.97/0.65 0.72/0.50

1.15/0.85

---

1.15/0.85 0.97/0.65 0.72/0.50 1.24/0.91

1.15/0.85

---

1.15/0.85 0.97/0.65 0.72/0.50

1.15/0.85 0.97/0.65 0.72/0.50 1.35/0.98

0.97/0.65 0.72/0.50 1.24/0.91

0.97/0.65 0.72/0.50

0.72/0.50

0.72-0.95/0.46-0.66

1.24/0.91

1.35 / 0.98

1.2/0.85

Page 17

Baumatic Ltd. Conditions of guarantee

Dear Customer,

Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship.

Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period applies to England, Scotland, Wales and Northern Ireland only.

To qualify for your full 24 months guarantee you must register your appliance within 28 days of purchase to be covered under this guarantee. This can be done online via: the guarantee card which can be found in each new Baumatic appliance.

* In addition, your appliance is covered by a 5 year parts warranty. Baumatic Ltd will provide free of charge the parts required to repair the appliance, only if they are fitted by a Baumatic engineer, for any defect that arises due to faulty materials or workmanship within a period of 5 years from the original purchase date. * An additional 1 to 3 year insurance scheme for labour is available should you wish to extend the

warranty period. Should any person other than an authorised representative of Baumatic Ltd interfere with the appliance, the policy is negated and Baumatic Ltd will be under no further liability.

The guarantee covers the appliance for normal domestic use only, unless otherwise stated.

Any claims made under the terms of the guarantee must be supported by the original invoice/bill of sale issued at the time of purchase.

This guarantee is transferable only with the written consent of Baumatic Ltd.

If the appliance fails and is considered either not repairable or uneconomical to repair between 12 months (2 years if registered) and five years, a free of charge replacement will not be offered.

The guarantee for any replacement will only be for the remainder of the guarantee on the original product purchased.

The guarantee does not cover:

- Sinks and taps

- Failure to comply with the manufacturers instructions for use.

- The replacement of cosmetic components of accessories

- Accidental damage or wilful abuse.

- Subsequent loss or damage owing to the failure of the appliance or electrical supply

- Incorrect installation

- Losses caused by Acts of God, civil war, failure to obtain spare parts, strikes or lockouts

- Filters, fuses, light bulbs, external hoses, damage to bodywork, paintwork, plastic items, covers, baskets, trays, shelves, burner bases, burner caps, decals, corrosion, rubber seals.

In the course of the work carried out it may be necessary to remove the appliance from it operating position. Whilst all reasonable care will be taken, Baumatic Ltd cannot accept responsibility for damage sustained to any property whatsoever in this process.

This guarantee is in addition to and does not diminish your statutory or legal rights.

Contacting Baumatic Ltd

Sales Service Spares Technical/Advice TEL: 0118 933 6900 TEL: 0118 933 6911 TEL: 0118 933 6922 0118 933 6933 FAX: 0118 931 0035 FAX: 0118 986 9124 FAX: 0118 933 6942 0118 933 6942 For ROI (Republic of Ireland), please contact one of the numbers below: TEL: 01 – 6266798 FAX: 01 - 6266634

Thanks you for buying Baumatic. *

Applies to UK, Scotland, Wales & Northern Ireland only (Republic of Ireland has 1 year labour & 1 year parts warranty only)

www.baumatic.co.uk or through returning

Page 18

Headquarters

Baumatic Ltd.

Baumatic Buildings,

6 Bennet Road,

Reading,

Berkshire

RG2 0QX, United Kingdom

Sales Telephone

+44 118 933 6900

Sales Fax

+44 118 931 0035

Service Telephone

+44 118 933 6911

Service Fax

+44 118 986 9124

Spares Telephone

+44 118 933 6922

Technical / Advice Telephone

+44 118 933 6933

E-mail:

sales@baumatic.co.uk

technical@baumatic.co.uk

Http (Internet site):

www.baumatic.com

Page 19

Environmental note

o The packaging materials that Baumatic uses are environmentally

friendly and can be recycled.

o Please discard all packaging material with due regard for the

environment.

Page 20