Bauknecht GSI 5919/1 IN BK, GSI 5919/1 SW BK, GSI 5919/1 WS BK Quick Reference Guide

Before using the dishwasher, read the user instructions!
GSI 5919
Indicators
Quick Reference Guide
Programme selection button
On / Off button
Start button
Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme.
Add regeneration salt
Add rinse aid
Options
GB
3)
Time and failure display
Indicates in hours the time remaining until the start of the wash cycle. Switches off at programme start and indicates the remaining time in hours and minutes.
“F....” Information for the After-Sales Service
“Delayed start” button
The wash cycle can be programmed to start after 1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour , and after 24 returns to 00. Then press the Start button. The dishwasher will start at the set time.
“Half load - Multizone” button
Load the upper or lower rack This function can be used with any programme. Press once = upper rack (the indication lamp/symbol comes on) Press twice = lower rack (the indication lamp/symbol comes on) Press 3 times = Off (half load function deactivated). When washing without the top rack, press the “Half Load” button twice, or “Lower rack wash” (the corresponding LED/symbol comes on).
Antibacterial rinse
This function adds an antibacterial rinse at the end of the wash cycle, thereby guaranteeing a perfectly clean and sanitized load. The lamp will light up when the function is activated. If the temperature is not maintained during the antibacterial cycle (e.g. if the door is opened and remains open for a long time), the lamp will start blinking to indicate that sanitation is not guaranteed.
4) 5)
only
.
Programme chart
Programmes Loading instructions A B
5)
Sensor +
40-70°C
Pre-Rinse cold Glass 40°C Rapid 30 min 40°C
1) 5) 6)
Bio
1) Reference programme for energy label EN 50242;
2) Refer to “User instructions”;
3) Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.: different loads, options, water temperatures - above or below 15°C - as well as water hardness and power supply voltage, etc.
Important information for Test Laboratories: For detailed information on the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
50°C
Lightly, normally or heavily soiled crockery, including pots and pans.
Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example glasses and cups.
Lightly soiled crockery with no dried-on food.
Normally soiled crockery. X X 13.0 1.05 195
4) The bacteria removal efficiency has been tested by the Institut Pasteur de Lille (France), based on the NF EN 13697 standard of November 2001.
5) These programmes can be used with the Antibacterial rinse option.
6) Energy saving programme with prolonged drying cycle.
(We reserve the right to make technical modifications)
Detergent
X X 7.0-17.0 0.99-1.58 65-170
X - 10.0 0.85 100
X - 10.0 0.65 30
2)
Consumption
Litres kWh Minutes
3)
5019 496 90454
How to use the appliance
ABC
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
Select, save, and
supply the detergent
Check the rinse aid level
Check the
regeneration salt level
Load the racks
Press the ON / OFF button.
(The first time you use the appliance and when using a different type of detergent)
1. Select the third programme from the top in the relative table.
2. Press the Start button for about 7 seconds until the display changes.
3. Select the required detergent with the Start button (OFF = powder detergent, 2 in 1, 3 in1, 4in1) (shown on the display).
4. Switch the appliance off and then switch it on again. The selected detergent type will be shown on the display for approximately 3 seconds after switching on.
For dosage of powder detergent in compartment A and B refer to the programmes table.
Mechanical indicator lamp C. Electric indicator on control panel (if provided).
On models with water softener system only.
Mechanical indicator lamp D. Electric indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
Close the dishwasher door,
turn on the water tap
Select a programme
Select additional options
Press the Start button
Wash cycle
Switch off the appliance
Turn off the water tap,
unload the racks
The last programme selected will light up. Select the desired programme (using the specific button or knob). The corresponding indicator lamp lights up.
If necessary (and if provided). The corresponding indicator lamp lights up.
The selected programme is then memorised (even in the event of power failure).
Only after the START button has switched off: Press the ON / All the indicator lamps switch off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
“Change programme in progress”
Press the START button for 2 sec. until the Start indicator lamp switches off.
Select another programme and press the START button again.
- Only open the dishwasher if necessary (Warning: beware of hot steam).
- I f the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.
OFF
button.
Loading...
+ 2 hidden pages