Bauknecht GCI3061XB User Manual

30" (76.2 CM) AND 36" (91.4 CM) ELECTRIC INDUCTION
COOKTOP INSTALLATION INSTRUCTIONS
INSTRUCTIONS D'INSTALLATION DE
LA TABLE DE CUISSON ÉLECTRIQUE À INDUCTION DE
30" (76,2 CM) ET DE 36" (91,4 CM)
Table of Contents/Table des matières
INSTALLATION REQUIREMENTS ......................................................... 2
Tools and Parts..................................................................................... 2
Location Requirements......................................................................... 2
Electrical Requirements ....................................................................... 4
INSTALLATION INSTRUCTIONS ........................................................... 4
Prepare Location................................................................................... 4
Install Brackets...................................................................................... 4
Install Cooktop...................................................................................... 5
Make Electrical Connection.................................................................. 6
Complete Installation ............................................................................7
SÉCURITÉ DE LA TABLE DE CUISSON .............................................9
EXIGENCES D'INSTALLATION............................................................9
Outillage et pièces..............................................................................9
Exigences d’emplacement...............................................................10
Spécifications électriques ...............................................................12
INSTRUCTIONS D'INSTALLATION ...................................................12
Préparation de l'emplacement .........................................................12
Installation des supports ..................................................................13
Installation de la table de cuisson....................................................14
Raccordement électrique.................................................................14
Achever l'installation.........................................................................16
COOKTOP SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
follow instructions.
can be killed or seriously injured if you don't
You
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT:
Save for local electrical inspector's use.
IMPORTANT :
À conserver pour consultation par l'inspecteur local des installations électriques.
501910200567D
instructions.
follow
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Too ls ne ed ed
Tap e m e as ure
Flat-blade screwdriver
Phillips head screwdriver
Hand or electric drill
Level
Marker or pencil
Pliers
¼" drill bit
Jigsaw
30" (76.2 cm) cooktop model/serial rating plate location (models JIC4430, GCI3061, ICI500, KICU500 and KICU509)
Parts supplied
Brackets (2)
2¹⁄₂" (6.4 cm) clamping screws (4)
#8 x ³⁄₈" (9.5 mm) sheet metal screws (4)
Parts needed
A UL listed or CSA approved strain relief
UL listed wire connectors
Check local codes. Check existing electrical supply. See “Electrical Requirements.”
It is recommended that all electrical connections be made by a licensed, qualified electrical installer.
Location Requirements
Make sure you have everything needed for correct installation. It is the responsibility of the installer to comply with the installation clearances specified in these instructions.
IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use minimum dimensions given.
To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The model/serial rating plate is located on the underside of the cooktop burner box.
A
A. Model/serial rating plate location
36" (91.4 cm) cooktop model/serial rating plate location (models JIC4536 and KICU569)
A
A. Model/serial rating plate location
Check the cooktop base for an approved installation label.
Verify approved oven model number that can be installed with your cooktop model number. If you don't find this label, your cooktop should not be used over a built-in oven.
Ovens approved for this type of installation will have an
approval label located on the top of the oven. If you do not find this label, contact your dealer to confirm that your oven is approved. Refer to oven manufacturer’s Installation Instructions for approval for built-in undercounter use and proper cutout dimensions.
When installing cooktop over an undercounter built-in oven,
do not fasten cooktop to countertop with clamps or seal cooktop to countertop. This will make the cooktop easier to remove if future servicing becomes necessary.
Use the countertop opening dimensions that are given with
these Installation Instructions. Given dimensions are minimum clearances and provide 0" (0 cm) clearance.
Grounded electrical supply is required. See “Electrical
Requirements” section.
2
Product Dimensions
30" (76.2 cm) Cooktops
A
D
A
Models JIC4430 and GCI3061
A. 21⁵⁄₁₆" (54.1 cm) B. 30⁵⁄₁₆" (77.0 cm) C. 2³⁄₈" (6.0 cm)
36" (91.4 cm) Cooktop
A
Cabinet Dimensions
B
C
Model ICI500 Models KICU500
and KICU509
A. 20¹⁄₈" (51.0 cm) B. 30⁵⁄₁₆" (77.0 cm) C. 2³⁄₈" (6.0 cm)
A. 21⁵⁄₁₆" (54.1 cm) B. 30³⁄₄" (78.2 cm) C. 2³⁄₈" (6.0 cm)
B
C
Models JIC4536
and KICU569
A. 21⁵⁄₁₆" (54.1 cm) B. 36⁵⁄₁₆" (92.0 cm) C. 2³⁄₈" (6.0 cm)
C
B
L
F
E
G
H
I
K
A. 29½" (75.0 cm) on 30" (76.2 cm) models
33¹⁄₁₆" (84.0 cm) on 36" (91.4 cm) models
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform
and bottom of uncovered wood or metal cabinet (24" [61 cm] minimum clearance if bottom of wood or metal cabinet is covered by not less than ¹⁄₄" [0.6 cm] flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D. 13" (33.0 cm) recommended upper cabinet depth
E. 2" (5.1 cm)
F. 1 9 ⁵⁄₁₆" (49.0 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of
countertop
I. Junction box or outlet; 10" (25.4 cm) from right-hand side of
cabinet
J. 29½" (75.0 cm) on 30" (76.2 cm) models
33¹⁄₁₆" (84.0 cm) on 36" (91.4 cm) models
K. 1" (2.5 cm) minimum distance to nearest left and right side
combustible surface above cooktop
L. 1" (2.5 cm) minimum clearance between back wall and countertop
J
IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.
NOTES: After you make the countertop cutout, some installations may require notching down the base cabinet side walls to clear the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.
If cabinet has a drawer, a 5¹⁄₈" (13 cm) depth clearance from the countertop to the top of the drawer (or other obstruction) in base cabinet is required.
For proper ventilation, provide a vent of ³⁄₁₆" (5 mm) under the countertop, in the front of the cabinet. The clearance should be the length of the cooktop cutout.
³⁄₁₆" (5 mm)
3
Electrical Requirements
WARNING
If the house has aluminum wiring, follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.
Electrical Shock Hazard Disconnect power before servicing. Use 8 gauge copper wire. Electrically ground cooktop. Failure to follow these instructions can result in death,
fire, or electrical shock.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes.
Check with a qualified electrical installer if you are not sure the cooktop is properly grounded.
It is not recommended to have a fuse in the neutral or ground circuit.
Make sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances.
A copy of the above code standards can be obtained from: National Fire Protection Association
One Batterymarch Park Quincy, MA 02269
CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-5575
INSTALLATION INSTRUCTIONS
Prepare Location
1. Decide on the final location for the cooktop. NOTE: Countertop must be 1³⁄₁₆" (3.0 cm) to 2" (5.1 cm) thick.
2. If necessary, make cutout in countertop before installing
cooktop. See “Location Requirements” section for more information.
3. Clean cutout of any remaining dust and debris.
Install Brackets
NOTE: Kit Part Number W10310006 is required for installing the cooktop into a solid surface or marble countertop. See the “Assistance or Service” section of the Use and Care Guide for information on ordering.
To Install Brackets into Marble Countertop:
1. Clean the brackets and cooktop cutout of any dust and
debris.
Before You Make the Electrical Connection:
To properly install your cooktop, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only
electrical supply is required on a separate, 50-amp circuit (36" [91.4 cm] models) or 40-amp circuit (30" [76.2 cm] models), fused on both sides of the line.
The cooktop should be connected directly to the junction box
through flexible, armored or nonmetallic sheathed, copper cable. The flexible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the junction box.
Locate the junction box to allow as much slack as possible
between the junction box and the cooktop so that the cooktop can be moved if servicing becomes necessary in the future.
Do not cut the conduit. The length of conduit provided is for
serviceability of the cooktop.
A UL listed or CSA approved conduit connector must be
provided at each end of the power supply cable (at the cooktop and at the junction box). A listed conduit connector is already provided at the cooktop.
2. Measure the center line of the vertical sides of the cooktop cutout.
Center line
3. Apply the adhesive provided in the kit to the back side of the brackets.
4
4. Position brackets in the center of the vertical centerline and
align the upper edge of the brackets so that they are flush with the countertop.
5. Push the brackets firmly onto each side of the cooktop cutout
and wait 1 hour for adhesive to dry.
Install Cooktop
WARNING
Excessive Weight Hazard Use two or more people to move and install cooktop. Failure to do so can result in back or other injury.
1. Using 2 or more people, lower the cooktop into the cutout
making sure the clips on each side of the cooktop line up with the brackets in the cutout.
1 h
To Install Brackets into Wood Countertop:
1. Measure the center line of the vertical sides of the cooktop
cutout.
Center line
2. Position brackets in the center of the vertical centerline and
align the upper edge of the brackets so that they are flush with the countertop.
3. Attach the brackets in the cutout with the screws provided.
A
A
A. Clip
2. Push down on cooktop to snap the cooktop clips onto the
brackets installed in the cutout.
A
B
A. Cooktop B. Cooktop cutout
B
A. Bracket B. Screw
5
Loading...
+ 11 hidden pages