Page 1
Safety data sheet
Page: 1/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
1. Identification
Product identifier
Ultrafuse PP
Chemical name: Ultrafuse PP
Recommended use: 3D Printing
Details of the supplier of the safety data sheet
Company:
BASF 3D Printing Solutions B.V.
Eerste Bokslootweg 17
7821 AT Emmen, Netherlands
Telephone: + 31 591 820 389
E-mail address: [email protected]
Emergency telephone number
National Poisoning Information Centre: +31 30 – 2748888
Information only for professionals in case of acute intoxication
International emergency number:
Telephone: +49 180 2273-112
2. Hazards Identification
Classification of the substance or mixture
According to UN GHS criteria
No need for classification according to GHS criteria for this product.
Label elements
Page 2
Page: 2/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Globally Harmonized System (GHS)
The product does not require a hazard warning label in accordance with GHS criteria.
Other hazards
According to UN GHS criteria
No specific dangers known, if the regulations/notes for storage and handling are considered.
3. Composition/Information on Ingredients
Substances
Chemical nature
Polymer
Hazardous ingredients (GHS)
According to UN GHS criteria
No particular hazards known.
Mixtures
Not applicable
4. First-Aid Measures
Description of first aid measures
Remove contaminated clothing.
If inhaled:
Keep patient calm, remove to fresh air.
On skin contact:
Wash thoroughly with soap and water. Burns caused by molten material require hospital treatment. If
irritation develops, seek medical attention.
On contact with eyes:
In case of contact with the eyes, rinse immediately for at least 15 minutes with plenty of water. If
irritation develops, seek medical attention.
On ingestion:
Page 3
Page: 3/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Rinse mouth and then drink 200-300 ml of water. If adverse health effects develop seek medical
attention.
Most important symptoms and effects, both acute and delayed
Symptoms: (Further) symptoms and / or effects are not known so far
Hazards: No hazard is expected under intended use and appropriate handling.
Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific
antidote.
5. Fire-Fighting Measures
Extinguishing media
Suitable extinguishing media:
water spray, foam, dry powder
Special hazards arising from the substance or mixture
carbon oxides
The substances/groups of substances mentioned can be released in case of fire.
Advice for fire-fighters
Special protective equipment:
Wear a self-contained breathing apparatus.
Further information:
Dispose of fire debris and contaminated extinguishing water in accordance with official regulations.
6. Accidental Release Measures
Avoid dispersal of dust in the air (i.e., clearing dust surfaces with compressed air). Avoid the
formation and build-up of dust - danger of dust explosion. Dust in sufficient concentration can result
in an explosive mixture in air. Handle to minimize dusting and eliminate open flame and other
sources of ignition.
Personal precautions, protective equipment and emergency procedures
No special precautions necessary.
Environmental precautions
Discharge into the environment must be avoided.
Methods and material for containment and cleaning up
For small amounts: Sweep/shovel up.
For large amounts: Sweep/shovel up. Vacuum up spilled product.
Reclaim for processing if possible. Ensure adequate ventilation. Avoid raising dust.
Page 4
Page: 4/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
7. Handling and Storage
Precautions for safe handling
Avoid inhalation of dusts/mists/vapours. Ensure adequate ventilation. Provide suitable exhaust
ventilation at the drying process and in the area surrounding the melt outlet of processing machines.
Keep away from sources of ignition - No smoking. Take precautionary measures against static
discharges. Avoid the formation and deposition of dust.
Protection against fire and explosion:
The product is not an oxidizer, not self-combustible and not explosive. Avoid dust formation. Dust in
sufficient concentration can result in an explosive mixture in air. Handle to minimize dusting and
eliminate open flame and other sources of ignition.
Conditions for safe storage, including any incompatibilities
Suitable materials for containers: High density polyethylene (HDPE), Low density polyethylene
(LDPE), Paper/Fibreboard
Storage stability:
Protect against moisture.
The product properties may change negatively with prolonged exposure to low temperature or frost.
Damage by exceeding the maximum temperature is not reversible.
8. Exposure Controls/Personal Protection
Control parameters
Components with occupational exposure limits
No occupational exposure limits known.
Exposure controls
Personal protective equipment
Respiratory protection:
Breathing protection if breathable aerosols/dust are formed. Wear respiratory protection if ventilation
is inadequate. Particle filter with medium efficiency for solid and liquid particles (e.g. EN 143 or 149,
Type P2 or FFP2)
Hand protection:
Use additional heat protection gloves when handling hot molten masses (EN 407), e.g. of textile or
leather.
Eye protection:
Safety glasses with side-shields (frame goggles) (e.g. EN 166)
Body protection:
Page 5
Page: 5/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Body protection must be chosen depending on activity and possible exposure, e.g. apron, protecting
boots, chemical-protection suit (according to EN 14605 in case of splashes or EN ISO 13982 in case
of dust).
General safety and hygiene measures
Wear protective clothing to prevent contact during mechanical processing and/or hot melt conditions.
Store work clothing separately. Hands and/or face should be washed before breaks and at the end of
the shift.
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Form: filament
Colour: natural
Odour: odourless
Odour threshold:
not applicable
pH value:
not applicable
Melting point: 220 - 240 °C
softening point: 105 °C
Boiling point:
not applicable
Flash point:
not applicable
Evaporation rate:
The product is a non-volatile solid.
Flammability: not flammable
Lower explosion limit:
For solids not relevant for
classification and labelling.
Upper explosion limit:
For solids not relevant for
classification and labelling.
Ignition temperature:
not applicable
Vapour pressure:
not applicable
Relative density: 1,05
Relative vapour density (air):
not applicable
Solubility in water: insoluble
Partitioning coefficient n-octanol/water (log Kow):
not applicable
Thermal decomposition: No decomposition if stored and handled as prescribed/indicated.
Prolonged thermal loading can result in products of degradation being
given off.
Page 6
Page: 6/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Viscosity, dynamic:
not applicable
Explosion hazard: not explosive
Fire promoting properties: not fire-propagating
Other information
Self heating ability: It is not a substance capable of
spontaneous heating.
10. Stability and Reactivity
Reactivity
No hazardous reactions if stored and handled as prescribed/indicated.
Corrosion to metals:
No corrosive effect on metal.
Chemical stability
The product is stable if stored and handled as prescribed/indicated.
Possibility of hazardous reactions
No hazardous reactions when stored and handled according to instructions.
Conditions to avoid
Avoid dust formation. Avoid deposition of dust.
Incompatible materials
Substances to avoid:
oxidizing agents
Hazardous decomposition products
Thermal decomposition products:
Prolonged thermal loading can result in products of degradation being given off.
11. Toxicological Information
Information on toxicological effects
Acute toxicity
Assessment of acute toxicity:
Virtually nontoxic after a single ingestion. Virtually nontoxic by inhalation. Virtually nontoxic after a
single skin contact.
Page 7
Page: 7/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Experimental/calculated data:
(oral):No applicable information available.
(by inhalation):The inhalation of dusts represents a potential acute hazard.
(dermal):No applicable information available.
Irritation
Experimental/calculated data:
Skin corrosion/irritation: May cause mechanical irritation.
Serious eye damage/irritation: May cause mechanical irritation.
Respiratory/Skin sensitization
Assessment of sensitization:
The chemical structure does not suggest a sensitizing effect. The product has not been tested. The
statement has been derived from substances/products of a similar structure or composition.
Germ cell mutagenicity
Assessment of mutagenicity:
The chemical structure does not suggest a specific alert for such an effect. The product has not been
tested. The statement has been derived from substances/products of a similar structure or
composition.
Carcinogenicity
Assessment of carcinogenicity:
The chemical structure does not suggest a specific alert for such an effect. The product has not been
tested. The statement has been derived from substances/products of a similar structure or
composition.
Reproductive toxicity
Assessment of reproduction toxicity:
The chemical structure does not suggest a specific alert for such an effect. The product has not been
tested. The statement has been derived from substances/products of a similar structure or
composition.
Developmental toxicity
Assessment of teratogenicity:
The chemical structure does not suggest a specific alert for such an effect. The product has not been
tested. The statement has been derived from substances/products of a similar structure or
composition.
Specific target organ toxicity (single exposure)
Page 8
Page: 8/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Assessment of STOT single:
Based on the available information there is no specific target organ toxicity to be expected after a
single exposure.
Remarks: The product has not been tested. The statement has been derived from the structure of
the product.
Repeated dose toxicity and Specific target organ toxicity (repeated exposure)
Assessment of repeated dose toxicity:
Repeated exposure to the substance by dermal administration leads to effects similar to those found
after single exposure. Repeated exposure to the substance by inhalative administration leads to
effects similar to those found after single exposure. Repeated exposure to the substance by oral
administration leads to effects similar to those found after single exposure. The product has not been
tested. The statement has been derived from substances/products of a similar structure or
composition.
Aspiration hazard
No aspiration hazard expected.
Other relevant toxicity information
The product has not been tested. The statement has been derived from substances/products of a
similar structure or composition.
12. Ecological Information
Toxicity
Assessment of aquatic toxicity:
There is a high probability that the product is not acutely harmful to aquatic organisms. Based on
long-term (chronic) toxicity study data, the product is very likely not harmful to aquatic organisms.
The product has not been tested.
Persistence and degradability
Assessment biodegradation and elimination (H2O):
Experience shows this product to be inert and non-degradable.
The product has not been tested.
Bioaccumulative potential
Assessment bioaccumulation potential:
The product has not been tested.
Mobility in soil
Assessment transport between environmental compartments:
Page 9
Page: 9/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
Adsorption in soil: Adsorption to solid soil phase is expected.
Other adverse effects
The product does not contain substances that are listed in Annex I of Regulation (EC) 2037/2000 on
substances that deplete the ozone layer.
13. Disposal Considerations
Waste treatment methods
Dispose of in accordance with national, state and local regulations.
Contaminated packaging:
Dispose of in accordance with national, state and local regulations.
14. Transport Information
Land transport
ADR
Not classified as a dangerous good under transport regulations
UN number:
Not applicable
UN proper shipping name:
Not applicable
Transport hazard class(es):
Not applicable
Packing group:
Not applicable
Environmental hazards:
Not applicable
Special precautions for
user
None known
RID
Not classified as a dangerous good under transport regulations
UN number:
Not applicable
UN proper shipping name:
Not applicable
Transport hazard class(es):
Not applicable
Packing group:
Not applicable
Environmental hazards:
Not applicable
Special precautions for
user
None known
Inland waterway transport
ADN
Not classified as a dangerous good under transport regulations
Page 10
Page: 10/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
UN number:
Not applicable
UN proper shipping name:
Not applicable
Transport hazard class(es):
Not applicable
Packing group:
Not applicable
Environmental hazards:
Not applicable
Special precautions for
user:
None known
Transport in inland waterway vessel
Not evaluated
Sea transport
IMDG
Not classified as a dangerous good under transport regulations
UN number:
Not applicable
UN proper shipping name:
Not applicable
Transport hazard class(es):
Not applicable
Packing group:
Not applicable
Environmental hazards:
Not applicable
Special precautions for
user
None known
Air transport
IATA/ICAO
Not classified as a dangerous good under transport regulations
UN number:
Not applicable
UN proper shipping name:
Not applicable
Transport hazard class(es):
Not applicable
Packing group:
Not applicable
Environmental hazards:
Not applicable
Special precautions for
user
None known
Transport in bulk according to Annex II of MARPOL and the IBC Code
Regulation:
Not evaluated
Shipment approved:
Not evaluated
Pollution name:
Not evaluated
Pollution category:
Not evaluated
Ship Type:
Not evaluated
Page 11
Page: 11/11
BASF Safety data sheet according to UN GHS 4th rev.
Date / Revised: 14.11.2019 Version: 2.0
Product: Ultrafuse PP
(ID no. 972169/SDS_GEN_00/EN)
Date of print 17.11.2019
15. Regulatory Information
Safety, health and environmental regulations/legislation specific for the substance or
mixture
If other regulatory information applies that is not already provided elsewhere in this safety data
sheet, then it is described in this subsection.
16. Other Information
The data contained in this safety data sheet are based on our current knowledge and experience and
describe the product only with regard to safety requirements. This safety data sheet is neither a
Certificate of Analysis (CoA) nor technical data sheet and shall not be mistaken for a specification
agreement. Identified uses in this safety data sheet do neither represent an agreement on the
corresponding contractual quality of the substance/mixture nor a contractually designated use. It is the
responsibility of the recipient of the product to ensure any proprietary rights and existing laws and
legislation are observed.
Vertical lines in the left hand margin indicate an amendment from the previous version.
Loading...