120L
860015
Bartscher GmbH
Franz-Kleine-Str. 28
D-33154 Salzkotten
Germany
Phone: +49 5258 971-0
Fax: +49 5258 971-120
Service hotline: +49 5258 971-197
www.bartscher.com
Version: 1.0
Date of preparation: 2023-03-24
Original instruction manual
EN
EN
Name:
Bin bag stand 120L
Art. No.:
860015
Material:
stainless steel | rubber | plastic
Designed for:
120-litre bin bags
Number of feet:
2
Number of swivel castors with brakes
2
Diameter of castors, in mm:
50
Dimensions (W x D x H), in mm:
590 x 500 x 955
Weight, in kg:
4,4
Technical Data
We reserve the right to implement technical modifications.
Version / Characteristics
• Delivery form: self-assembly set (simple assembly)
• Version:
– retainer for bin bags
– hanger for cleaning utensils, etc.
– seal with clamping rubber
• Operation: push mechanism (foot pedal)
• The set does not include: bin bags
Intended Use
As described below, every use of the appliance for a purpose differing and/or
diverging from its intended standard use, is prohibited and considered to be an
unintended use.
The following is an intended use:
– putting rubbish into the bin bag.
860015 3 / 8
EN
Fig. 1
Scope of Delivery / Part Name
• Unpack the bin bag stand and dispose of the packaging material observing the
environmental regulations.
• Check the completeness of delivery according to the list below:
4 / 8 860015
EN
No.
Name
Number
1
Rubber strip
1
2
Rubber strip fastening plate
1
3
Bin bag fixing plate
1
4
M5*12 bolts
4
5
Front bracket
1
6
M4*16 bolts
4
7
Shelf for bin bags
1
8
Foot pedal
1
9
Locking swivel castor
2
10
Bottom frame
1
11
Rear support
1
12
Hanger (e.g., for cleaning utensils)
1
Assembly
1. Mount both brackets (5 and 11, Fig. 1) on the bottom frame (10) using M4*16
screws (6). When doing so, make sure that the bracket (11) with the hanger (12)
is installed at the rear of the frame.
2. Screw the attachment plate of the bin bag fixing plates (3) first to the rear
bracket (11) with two M5*12 screws (4).
3. Then screw the fastening plate of the bin bag fastening plates (3) and the
fastening plate (2) of the rubber strip (1) to the front bracket (5) of the support
with two more M5*12 screws (4) (detail — see Fig. 1).
4. Finally, screw 2 swivel castors (9) into the tubes of the lower support (10).
5. Position the bin bag stand in the desired location and lock the swivel castors (9)
with the locks.
860015 5 / 8
EN
The appropriate bin bag can be easily
attached to the stand.
1. Press the foot pedal on the stand.
The attachment plates of the bin bags of the
stand open.
Fig. 2
2. Pull the bin bad through the bin bag fixing
plates.
3. Release the foot pedal.
Fig. 3
Indications for User
Hygienic, fast and easy; the large foot pedal of the bottom frame locking
mechanism makes clean disposal of rubbish very simple. The locking mechanism
keeps unpleasant odours where they belong — in the bin bag.
The lidless system also allows the bin bag stand to be placed in slightly lower
corners.
6 / 8 860015
EN
4. Pull the edge of the bin bag over the bin
bag fixing plates.
5. Fasten the bin bag with the rubber strip.
Use bottom stand shelf to support the bin bag
while it is being filled.
Fig. 4
6. Simple waste disposal:
– press the foot pedal: the plastic plate of
the stand opens;
– throw the rubbish into the bin bag;
– release the foot pedal.
When the foot pedal is released, the stand at
the top closes again automatically (by spring
action) and thus also closes the opening of
the bin bag.
7. When the bin bag is full, pull the rubber
strip upwards.
8. Press the foot pedal and pull the filled bin
bag out of the stand.
9. Hang a new bin bag on the stand.
Fig. 5
860015 7 / 8
EN
ATTENTION!
Scrubbing agents, cleaning agents with solvents or caustic substances
may damage the surface of the stand.
For cleaning, use only cleaning agents suitable for stainless steel and
plastic.
Cleaning
1. Clean the bin bag stand regularly with warm water and a soft, damp cloth. Use a
mild cleaning agent when required.
2. Dry the bin bag stand with a soft cloth.
8 / 8 860015
Loading...