Bard WA361, WA301 User Manual

WALL MOUNTED

INSTALLATION
INSTRUCTIONS

PACKAGED

AIR CONDITIONER

Models:

WA301, WA361

Bard Manufacturing Company
Bryan, Ohio 43506

Since 1914...Moving ahead just as planned.

MIS-656

Manual No.: 2100-192M
Supersedes: 2100-192L
File: Volume III, Tab 16
Date: 05-13-02

© Copyright 2002

Contents

Getting Other Information and Publications

For more information,

contact these publishers ........................................1

Wall Mount General Information

Air Conditioner Wall Mount Model Nomenclature .. 2

Shipping Damage .................................................. 5

General ..................................................................5

Duct Work ..............................................................5

Filters .....................................................................5

Fresh Air Intake ...................................................... 6

Condensate Drain .................................................. 6

Installation Instructions

Wall Mounting Information ..................................... 7

Mounting the Unit ................................................... 7

Top Outlet Only ...................................................... 7

Wiring — Main Power ............................................ 7

Wiring — Low Voltage Wiring................................. 8

Figures

Figure 1 Unit Dimensions ................................... 3

Figure 2 Blower Damper Assembly.....................6

Figure 3 Mounting Instructions ........................... 9

Figure 4 Electric Heat Clearances ...................... 9

Figure 5 Wall-Mounting Instructions ................. 10

Figure 6 Wall-Mounting Instructions ................. 10

Figure 7 Common Wall-Mounting Installations . 11

Figure 8 Low Voltage Wiring ............................. 12

Figure 9 Start Up Label ..................................... 13

Figure 10 Fan Blade Setting ...............................15

Start Up

Important Installer Note........................................13

Crankcase Heaters .............................................. 13

Service Hints ........................................................ 13

Sequence of Operation ........................................ 13

Compressor Control Module ................................13

Adjustments .........................................................14

Pressure Service Ports ........................................ 14

Troubleshooting

Fan Blade Setting Dimensions ............................ 15

Removal of Fan Shroud ....................................... 15

Refrigerant Charge .............................................. 15

Pressure Table ..................................................... 16

Optional Accessories ...........................................17

Tables

Table 1 Electrical Specifications ........................ 2

Table 2 Dimensions of Basic Unit ...................... 3

Table 3 Electric Heat Table................................4

Table 4 Operating Voltage Range ..................... 8

Table 5 Thermostat Wire Size ........................... 8

Table 6 Wall Thermostat and

Subbase Combinations ........................ 8

Table 7 Fan Blade Dimensions ....................... 15

Table 8 Suction Line Temperatures ................. 15

Table 9 Indoor Blower Performance ................ 15

Table 10 CFM and ESP ..................................... 15

Table 11 Maximum ESP of Operation

Electric Heat Only ............................... 16

Table 12 Cooling Pressure ................................ 16

Table 13 Optional Accessories .......................... 17

i

Getting Other Information and Publications

These publications can help you install the air
conditioner or heat pump. You can usually find these at
your local library or purchase them directly from the
publisher. Be sure to consult current edition of each
standard.

National Electrical Code ....................... ANSI/NFPA 70

Standard for the Installation ............... ANSI/NFPA 90A

of Air Conditioning and
Ventilating Systems

Standard for Warm Air ........................ ANSI/NFPA 90B

Heating and Air
Conditioning Systems

Load Calculation for ............................. ACCA Manual J

Residential Winter and
Summer Air Conditioning

Duct Design for Residential ................ACCA Manual D

Winter and Summer Air
Conditioning and Equipment
Selection

FOR MORE INFORMATION, CONTACT
THESE PUBLISHERS:

ACCA Air Conditioning Contractors of America

1712 New Hampshire Avenue NW
Washington, DC 20009
Telephone: [phone]
Fax: [phone]

ANSI American National Standards Institute

11 West Street, 13th Floor
New York, NY 10036
Telephone: [phone]
Fax: [phone]

ASHRAE American Society of Heating Refrigerating,

and Air Conditioning Engineers, Inc.

1791 Tullie Circle, N.E.
Atlanta, GA 30329-2305
Telephone: [phone]
Fax: [phone]

NFPA National Fire Protection Association

Batterymarch Park
P.O. Box 9101
Quincy, MA 02269-9901
Telephone: [phone]
Fax: [phone]

Manufactured under the following U.S. patent numbers:

5,485,878; 5,301,744; 5,002,116;

4,924,934; 4,875,520; 4,825,936

Manual 2100-192
Page 1

WALL MOUNT GENERAL INFORMATION

AIR CONDITIONER WALL MOUNT MODEL NOMENCLATURE

MODEL
NUMBER

CAPACITY

30 - 2 1/2 Ton
36 - 3 Ton

VOLTS & PHASE

A - 230/208/60/1
B - 230/208/60/3
C - 460/60/3

NOTE: For 0KW and circuit breakers (230/208 Volt) or pull disconnects (460 Volt) applications, insert 0Z in the KW field of
model number.

REVISIONS

WA361–A10X XXXXA

KW

VENTILATION OPTIONS

X - Barometric Fresh Air
Damper

(Standard)
B - Blank-off Plate
M - Motorized Fresh Air Damper
V - Commercial Room Ventilator

-

Motorized with Exhaust
E - Economizer (Internal - Fully

Modulating with Exhaust
R - Energy Recovery Ventilator -

with Exhaust

FILTER OPTIONS

X - One Inch Throwaway

W - One Inch Washable
P - Two Inch Pleated

COLOR OPTIONS

X - Beige (Standard)
1 - White
2 - Mesa Brown
4 - Buckeye Gray
5 - Desert Brown
6 - Dark Bronze

(Standard)

CONTROL MODULES

COIL OPTIONS
X - Standard

1 - Phenolic Coated Evapora­tor
2 - Phenolic Coated Con­denser
3 - Phenolic Coated Evapora­tor

and Condenser

OUTLET OPTIONS

X - Front (Standard)
T - Top on WA30 and WA36

Models

TABLE 1

ELECTRICAL SPECIFICATIONS

3

detaR

ledoM

Z0A,00A-103AW
50A
01A
51A

Z0B,00B-103AW
90B
51B

Z0C,00C-103AW
90C
51C

Z0A,00A-163AW
50A
01A
51A

Z0B,00B-163AW
90B
51B

Z0C,00C-163AW
90C
51C

Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors.

1

Based on 75° copper wire. All wiring must conform to the National Electrical Code and all local codes.

2

These "Minimum Circuit Ampacity" values are to be used for sizing the field power conductors. Refer to the National Electric

3

Code (latest revision), Article 310 for power conductor sizing.

is run through one conduit, the conductors must be derated. Pay special attention to note 8 of table 310 regarding
Ampacity Adjustment Factors when more than three conductors are in a raceway.

&stloV
esahP

3-064

3-064

.oN
dleiF

rewoP

stiucriC

1
1

1-802/032

1

2ro1

1

3-802/032

1
1

1
1
1

1
1

1-802/032

1

2ro1

1

3-802/032

1
1

1
1
1

42
13
75
38

71
23
05

01
71
62

72
13
75
38

02
23
05

01
71
62

1

muminiM
tiucriC

yticapmA

53
53
06
09

02
53
05

51
02
03

53
53
06
09

52
53
05

51
02
03

2

mumixaM

lanretxE
roesuF
.tiucriC
rekaerB

8
8
6
4

8
8

8
8
6
4

8
8

2

dleiF

rewoP
eriW
eziS

21

41
21
01

01

41
21
01

CAUTION: When more than one field power conductor circuit

eriW
eziS

01
01
01

8

21
01
01

41
21
01

01
01
01

8

01
01
01

41
21
01

3

muminiM

55

tiucriC

yticapmA

TKC

A

B

---

---

---

---

---

---

62

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

55

62

---

---

---

---

---

---

---

---

---

---

---

---

dnuorG

1

mumixaM

lanretxE

roesuF

tiucriC

rekaerB

TKC

TKC

A

TKC

B

A

---

---

---

---

---

---

06

03

4

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

06

03

4

---

---

---

---

---

---

---

---

---

---

---

---

2

dleiF

rewoP

eziSeriW

TKC

TKC

B

---

---

---

---

---

---

01

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

01

---

---

---

---

---

---

---

---

---

---

---

---

2

dnuorG

eziSeriW

TKC

A

8

8

TKC

B

---

---

---

---

---

---

01

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

---

01

---

---

---

---

---

---

---

---

---

---

---

---

Manual 2100-192
Page 2

MIS-1262

TABLE 2

FIGURE 1

UNIT DIMENSIONS

EFGI JKLMNOPQRSTABCB

DIMENSIONS OF BASIC UNIT (NOMINAL)

ylppuSnruteR

thgieH

)H(

htpeD

)D(

htdiW

002.83521.71365.0788.788.7288.3188.7200.0405.8157.5239.7157.6257.8252.9200.7257.291.9357.2241.991.400.2100.5

)W(

ledoM

03AW

63AW

Optional top outlet (factory installed only) for WA30 and WA36 models only.

*

FRONT VIEW BACK VIEWSIDE VIEW

Manual 2100-192
Page 3

TABLE 3

ELECTRIC HEAT TABLE

A-103AWB-103AWC-103AWA-163AWB-163AWC-163AW

1-V0421-V8023-V0423-V8023-V0641-V0421-V8023-V0423-V8023-V064

Manual 2100-192
Page 4

sledoM

0.58.02560,711.81008,21------------------8.02560,711.81008,21------------------

WKSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTBSPMAHUTB

0.016.14031,432.63006,52------------------6.14031,432.63006,52------------------

0.83.33003,728.82574,02------------------3.33003,728.82574,02------------------

0.51------------------------------5.26002,151.45004,83------------------

0.6------------4.41005,025.21063,512.7574,02------------4.41005,025.21063,512.7574,02

0.51------------0.81002,15------------2.63004,832.13004,830.81002,15

0.9------------7.12006,037.81030,328.01007,03------------7.12006,037.81030,328.01007,03

SHIPPING DAMAGE

Upon receipt of equipment, the carton should be
checked for external signs of shipping damage. If
damage is found, the receiving party must contact the
last carrier immediately, preferably in writing,
requesting inspection by the carrier’s agent.

GENERAL

The equipment covered in this manual is to be installed
by trained, experienced service and installation
technicians.

The refrigerant system is completely assembled and
charged. All internal wiring is complete.

Refer to Table 10 for maximum static pressure available
for duct design.

Design the duct work according to methods given by the
Air Conditioning Contractors of America (ACCA).
When duct runs through unheated spaces, it should be
insulated with a minimum of 1 inch of insulation. Use
insulation with a vapor barrier on the outside of the
insulation. Flexible joints should be used to connect the
duct work to the equipment in order to keep the noise
transmission to a minimum.

A 1/4 inch clearance to combustible material for the
first 3 feet of duct attached to the outlet air frame is
required. See Wall Mounting Instructions and Figures 3
and 4 for further details.

The unit is designed for use with or without duct work.
Flanges are provided for attaching the supply and return
ducts.

These instructions explain the recommended method to
install the air cooled self-contained unit and the
electrical wiring connections to the unit.

These instructions and any instructions packaged with
any separate equipment required to make up the entire
air conditioning system should be carefully read before
beginning the installation. Note particularly “Starting
Procedure” and any tags and/or labels attached to the
equipment.

While these instructions are intended as a general
recommended guide, they do not supersede any national
and/or local codes in any way. Authorities having
jurisdiction should be consulted before the installation is
made. See Page 1 for information on codes and
standards.

Size of unit for a proposed installation should be based
on heat loss calculation made according to methods of
Air Conditioning Contractors of America (ACCA). The
air duct should be installed in accordance with the
Standards of the National Fire Protection Association
for the Installation of Air Conditioning and Ventilating
Systems of Other Than Residence Type, NFPA No.
90A, and Residence Type Warm Air Heating and Air
Conditioning Systems, NFPA No. 90B. Where local
regulations are at a variance with instructions, installer
should adhere to local codes.

DUCT WORK

Ducts through the walls must be insulated and all joints
taped or sealed to prevent air or moisture entering the
wall cavity.

CAUTION

Some installations may not require any return
air duct. A metallic return air grille is required
with installations not requiring a return air
duct. The spacing between louvers on the
grille shall not be larger than 5/8 inches.

Any grille that meets the 5/8 inch louver criteria may be
used. It is recommended that Bard Return Air Grille Kit
RG-2 through RG-5 or RFG-2 through RFG-5 be
installed when no return duct is used. Contact
distributor or factory for ordering information. If using
a return air filter grille, filters must be of sufficient size
to allow a maximum velocity of 400 fpm.

FILTERS

A 1 inch throw away filter is suppled with each unit.
The filter slides into position making it easy to service.
This filter can be serviced from the outside by removing
the service door. A 1 inch washable filter and a 2 inch
pleated filter are also available as optional accessories.
The internal filter brackets are adjustable to
accommodate the 2 inch filter by loosening 2 screws in
each bracket assembly and sliding the brackets apart to
the required width and retightening the 4 screws.

All duct work, supply and return, must be properly sized
for the design air flow requirement of the equipment.
Air Conditioning Contractors of America (ACCA) is an
excellent guide to proper sizing. All duct work or
portions thereof not in the conditioned space should be
properly insulated in order to both conserve energy and
prevent condensation or moisture damage.

Manual 2100-192
Page 5

FRESH AIR INTAKE

All units are built with fresh air inlet slots punched in
the service panel.

The blank-off plate is available upon request from the

factory and is installed in place of the fresh air damper

shipped with each unit.

If the unit is equipped with the fresh air damper
assembly, the assembly is shipped already attached to
the unit. The damper blade is locked in the closed
position. To allow the damper to operate, the maximum
and minimum blade position stops must be installed.
See Figure 2.

All capacity, efficiency and cost of operation
information as required for Department of Energy
“Energyguide” Fact Sheets is based upon the fresh air
blank-off plate in place and is recommended for
maximum energy efficiency.

FRESH AIR DAMPER ASSEMBLY

BLADE IS LOCKED
CLOSED FOR
SHIPPING

CONDENSATE DRAIN

A plastic drain hose extends from the drain pan at the

top of the unit down to the unit base. There are openings

in the unit base for the drain hose to pass through. In the

event the drain hose is connected to a drain system of

some type, it must be an open or vented type system to

assure proper drainage.

FIGURE 2

MIS-938

Manual 2100-192
Page 6

INSTALLATION INSTRUCTIONS

WALL MOUNTING INFORMATION

1. Two holes, for the supply and return air openings,
must be cut through the wall as shown in Figure 3.

2. On wood-frame walls, the wall construction must be
strong and rigid enough to carry the weight of the unit
without transmitting any unit vibration.

WARNING

Fire hazard can result if 1/4 inch clearance to
combustible materials for supply air duct is not
maintained. See Figure 3.

3. Concrete block walls must be thoroughly inspected to
insure that they are capable of carrying the weight of
the installing unit.

MOUNTING THE UNIT

1. These units are secured by wall mounting brackets
which secure the unit to the outside wall surface at
both sides. A bottom mounting bracket is provided for
ease of installation, but is not required.

2. The unit itself is suitable for “0” inch clearance, but
the supply air duct flange and the first 3 feet of supply
air duct require a minimum of 1/4 inch clearance to
combustible material. If a combustible wall, use a
minimum of 28-1/2" x 8-1/2" dimensions for sizing.
However, it is generally recommended that a 1 inch
clearance is used for ease of installation and
maintaining the required clearance to combustible
material. The supply air opening would then be 30" x
10". See Figures 3 and 4 for details.

WARNING

Failure to provide the 1/4 inch clearance
between the supply duct and a combustible
surface for the first 3 feet of duct can result in
fire.

3. Locate and mark lag bolt locations and bottom
mounting bracket location. See Figure 3.

4. Mount bottom mounting bracket, if used.

5. Hook top rain flashing under back bend of top. Top
rain flashing is shipped secured to the right side of the
back.

6. Position unit in opening and secure with 5/16 lag
bolts; use 7/8 inch diameter flat washers on the lag
bolts.

7. Secure rain flashing to wall and caulk across entire
length of top. See Figure 3.

8. For additional mounting rigidity, the return air and
supply air frames or collars can be drilled and
screwed or welded to the structural wall itself
(depending upon wall construction). Be sure to
observe required clearance if combustible wall.

9. On side by side installations, maintain a minimum of
20 inches clearance on right side to allow access to
heat strips and control panel and to allow proper
airflow to the outdoor coil. Additional clearance may
be required to meet local or national codes.

TOP OUTLET ONLY

1. Remove airframe angles from the back of the unit.

2. Coat angles with two 1/8" beads of silicone as shown.
Silicone is shipped in the control panel. See Figure 6.

3. Secure angles to the top of the unit with 14 screws
provided. Use of prepunched holes provided. Do not
relocate. See Figure 6.

4. After installation duct work, seal around airframe and
duct work to provide a rain tight seal.

5. It is strongly recommended, but not required, that this
unit be installed under a soffit area large enough to
shield the top of the unit. See Figure 7.

WIRING — MAIN POWER

Refer to the unit rating plate for wire sizing information
and maximum fuse or “HACR Type” circuit breaker
size. Each outdoor unit is marked with a “Minimum
Circuit Ampacity”. This means that the field wiring used
must be sized to carry that amount of current. Depending
on the installed KW of electric heat, there may be two
field power circuits required. If this is the case, the unit
serial plate will so indicate. All models are suitable only
for connection with copper wire. Each unit and/or wiring
diagram will be marked “Use Copper Conductors Only”.
These instructions must be adhered to. Refer to the
National Electrical Code (NEC) for complete current
carrying capacity data on the various insulation grades
of wiring material. All wiring must conform to NEC and
all local codes.

Manual 2100-192
Page 7

The electrical data lists fuse and wire sizes (75ºC
copper) for all models, including the most commonly
used heater sizes. Also shown are the number of field
power circuits required for the various models with
heaters.

The unit rating plate lists a “Maximum Time Delay
Relay Fuse” or “HACR Type” circuit breaker that is to
be used with the equipment. The correct size must be
used for proper circuit protection and also to assure that
there will be no nuisance tripping due to the momentary
high starting current of the compressor motor.

The disconnect access door on this unit may be locked to
prevent unauthorized access to the disconnect. To
convert for the locking capability, bend the tab located in
the bottom left hand corner of the disconnect opening
under the disconnect access panel straight out. This tab
will now line up with the slot in the door. When shut, a
padlock may be placed through the hole in the tab
preventing entry.

WIRING — LOW VOLTAGE WIRING

230/208V, 1 phase and 3 phase equipment dual primary
voltage transformers. All equipment leaves the factory
wired on 240V tap. For 208V operation, reconnect from
240V to 208V tap. The acceptable operating voltage
range for the 240 and 208V taps are:

TABLE 4

OPERATING VOLTAGE RANGE

PATEGNAR

V042612-352
V802781-022

NOTE: The voltage should be measured at the

field power connection point in the unit
and while the unit is operating at full load
(maximum amperage operating condition.)

Five (5) wires should be run from thermostat subbase to
the 24V terminal board in the unit. A five conductor, 18
gauge copper, color-coded thermostat cable is
recommended. The connection points are shown in
Figure 10.

TABLE 5

THERMOSTAT WIRE SIZE

mumixaM

remrofsnarT

AVALF

553.2

eriW

eguaG

eguag02
eguag81
eguag61
eguag41
eguag21

ecnatsiD

teeFnI

54
06

001
061
052

TABLE 6

WALL THERMOSTAT AND SUBBASE COMBINATIONS

tatsomrehTesabbuSserutaeFetanimoderP

200-3048

1113F78T

140-3048

C4308T

910-3048

0671C478T

120-3048

4391D478T

940-3048
083-39F1

340-3048

002-MC

300-4048

0221A935Q

---loocegats1,taehegats1

210-4048

1001A476Q

210-4048

1001A476Q

---taehegats2,loocegats2

---

loocegats1,taehegats1

no-otua:naFlooc-ffo-taeh:metsyS

no-otua:naFlooc-ffo-taeh:metsyS

taehegats2,loocegats1

taehegats2,loocegats2

gnimmargorpyad7cinortcelE

loocegats1,taehegats1

no-otua:naFlooc-otua-taeh:metsyS

no-otua:naFlooc-otua-taeh:metsyS

no-otua:naFlooc-ffo-taeh:metsyS

Manual 2100-192
Page 8

FIGURE 3

MOUNTING INSTRUCTIONS

4 9/
16

MIS-277

FIGURE 4

ELECTRIC HEAT CLEARANCE

Side section view of
supply air duct for wall
mounted unit showing 1/4
inch clearance to
combustible surfaces.

MIS-311

NOTE: It is recommended that a bead of silicone caulking be

placed behind the side mounting flanges and under the
top flashing at the time of installation.

WARNING

WARNING

• A minimum of 1/4 inch clearance must be
maintained between the supply air duct and
combustible materials. This is required for
the first 3 feet of ducting.

• It is important to insure that the 1/4 inch
minimum spacing is maintained at all
points.

• Failure to do this could result in overheat-

ing the combustible material and may
result in fire.

Manual 2100-192
Page 9

FIGURE 5

WALL-MOUNTING INSTRUCTIONS

SEE FIGURE 3 – MOUNTING INSTRUCTIONS

FIGURE 6

WALL-MOUNTING INSTRUCTIONS

SEE UNIT DIMENSIONS, FIGURE 1,
FOR ACTUAL DIMENSIONS

MIS-548

SEE FIGURE 1 FOR
DUCT DIMENSIONS

MIS-549

Manual 2100-192
Page 10

FIGURE 7

COMMON WALL-MOUNTING INSTALLATIONS

MIS-550

Manual 2100-192
Page 11

FIGURE 8

LOW VOLTAGE WIRING

Manual 2100-192
Page 12

MIS-1373C

START UP

IMPORTANT INSTALLER NOTE

For improved start-up performance, wash the indoor
coil with a dishwasher detergent.

CRANKCASE HEATERS

All units are provided with some form of compressor
crankcase heat.

All single and three phase models have an insertion
well-type heater located in the lower section of the
compressor housing. This is a self-regulating type
heater that draws only enough power to maintain the
compressor at a safe temperature.

Some form of crankcase heat is essential to prevent
liquid refrigerant from migrating to the compressor,
causing oil pump out on compressor start up and
possible valve failure due to compressing a liquid.

The decal in Figure 9 is affixed to all outdoor units
detailing start up procedure. This is very important.
Please read carefully.

SERVICE HINTS

1. Caution homeowner to maintain clean air filters at all
times. Also, not to needlessly close off supply and
return air registers. This reduces air flow through the
system, which shortens equipment service life as well
as increasing operating costs.

2. Check all power fuses or circuit breakers to be sure
they are the correct rating.

3. Periodic cleaning of the outdoor coil to permit full
and unrestricted airflow circulation is essential.

SEQUENCE OF OPERATION

Cooling—Circuit R-Y makes at thermostat pulling in
compressor contactor, starting the compressor and
outdoor motor. The G (indoor motor) circuit is
automatically completed on any call for cooling
operation or can be energized by manual fan switch on
subbase for constant air circulation. On all 230 volt
units there is a one minute off delay on the blower
motor. 460 volt models do not have an off delay. On a
call for heating, circuit R-W1 make at the thermostat
pulling in heat contact for the strip heat and blower
operation. On a call for second stage heat, R-W2 makes
bringing on second heat contactor, if so equipped.

COMPRESSOR CONTROL MODULE

The compressor control module is optional on the
models covered by this manual. The compressor control
is an anti-short cycle/lockout timer with high and low
pressure switch monitoring and alarm relay output.

Adjustable Delay On Make And Break Timer

On initial power up or any time power is interrupted to
the unit the delay on make period begins which will be
2 minutes plus 10% of the delay on break setting. When
the delay on make is complete and the high pressure
switch (and low pressure switch if employed) is closed,
the compressor contactor is energized. Upon shutdown
the delay or break timer starts and prevents restart until
the delay on break and delay on make periods have
expired.

During routine operation of the unit with no power
interruptions the compressor will operate on demand
with no delay.

FIGURE 9

START UP LABEL

IMPORTANT

These procedures must be followed
at initial start up and at any time
power has been removed for 12
hours or longer.

To prevent compressor damage which may
result from the presence of liquid refrigerant in
the compressor crankcase:

1. Make certain the room thermostat is in the
"off" position (the compressor is not to operate).

2. Apply power by closing the system
disconnect switch. This energizes the
compressor heater which evaporates the liquid
refrigerant in the crankcase.

3. Allow 4 hours or 60 minutes per poind of
refrigerant in the system as noted on the unit
rating plate, whichever is greater.

4. After properly elapsed time, the thermostat
may be set to operate the compressor.

5. Except as required for safety while servicing,

do not open system disconnect switch

.

7961-061

Manual 2100-192
Page 13

High Pressure Switch and Lockout Sequence

ADJUSTMENTS

If the high pressure switch opens, the compressor
contactor will de-energize immediately. The lockout
timer will go into a soft lockout and stay in soft lockout
until the high pressure switch closes and the delay on
break time has expired. If the high pressure switch
opens again in this same operating cycle the unit will go
into manual lockout condition and the alarm relay circuit
will energize. Recycling the wall thermostat resets the
manual lockout.

Low Pressure Switch, Bypass, and Lockout
Sequence

If the low pressure switch opens for more than 120
seconds, the compressor contactor will de-energize and
go into a soft lockout. Regardless the state of the low
pressure switch, the contactor will reenergize after the
delay on make time delay has expired. If the low
pressure switch remains open, or opens again for longer
than 120 seconds the unit will go into manual lockout
condition and the alarm relay circuit will energize.
Recycling the wall thermostat resets the manual lockout.

Alarm Relay Output

Alarm terminal is output connection for applications
where alarm relay is employed. This terminal is
powered whenever compressor is locked out due to HPC
or LPC sequences as described.

NOTE: Both high and low pressure switch controls are

inherently automatic reset devices. The high
pressure switch and low pressure switch cut
out and cut in settings are fixed by specific air
conditioner or heat pump unit model. The
lockout features, both soft and manual, are a
function of the Compressor Control Module.

Adjustable Delay on Make and Delay on Break
Timer

The potentiometer is used to select Delay on Break time
from 30 seconds to 5 minutes. Delay on Make (DOM)
timing on power-up and after power interruptions is
equal to 2 minutes plus 10% of Delay on Break (DOB)
setting:

0.5 minute (30 seconds) DOB = 123 second DOM

1.0 minute (60 seconds) DOB = 126 second DOM

2.0 minute (120 seconds) DOB = 132 second DOM

3.0 minute (180 seconds) DOB = 138 second DOM

4.0 minute (240 seconds) DOB = 144 second DOM

5.0 minute (300 seconds) DOB = 150 second DOM

During routine operation of the unit with no power
interruptions the compressor will operate on demand
with no delay.

Typical Settings for Dual Unit Installation:

Unit 1: DOB set at 2 minutes, and DOM is 132 seconds

Unit 2: DOB set at 4 minutes, and DOM is 144 seconds

PRESSURE SERVICE PORTS

High and low pressure service ports are installed on all
units so that the system operating pressures can be
observed. Pressure tables can be found later in the
manual covering all models. It is imperative to match
the correct pressure table to the unit by model number.

Manual 2100-192
Page 14

TROUBLESHOOTING

.P.S.E

HnI

2

O

163AW,103AW

deepShgiHdeepSwoL

lioCyrDlioCteWlioCyrDlioCteW

0.593,1513,1059539

1.043,1072,1039519

2.582,1091,1019588

3.502,1001,1558038

4.011,1000,1008557

5.500,1078------

ledoM

detaR
wolfriA

F°59

.pmeTDO

F°28

.pmeTDO

103AW001,175-5566-46
163AW001,195-7546-26

FAN BLADE SETTING DIMENSIONS

Shown in the drawing below are the correct fan blade
setting dimensions for proper air delivery across the
outdoor coil.

Any service work requiring removal or adjustment in the
fan and/or motor area will require that the dimensions
below be checked and blade adjusted in or out on the
motor shaft accordingly.

FIGURE 10

FAN BLADE SETTING

TABLE 7

FAN BLADE DIMENSION

ledoMAnoisnemiD

103AW
163AW

52.1

TABLE 8

SUCTION LINE TEMPERATURES

The suction line temperatures in Table 8 are based upon
80ºF dry bulb/67ºF wet bulb (50 percent R.H.)
temperature and rated airflow across the evaporator
during cooling cycle.

TABLE 9

INDOOR BLOWER PERFORMANCE

CFM AT 230 VOLTS

REMOVAL OF FAN SHROUD

1. Disconnect all power to unit.

2. Remove the screws holding both grills, one on each
side of unit, and remove grills.

3. Remove screws holding fan shroud to condenser and
bottom – 9 screws.

4. Unwire condenser fan motor.

5. Slide complete motor, fan blade, and shroud assembly
out the left side of the unit.

6. Service motor/fan as needed.

7. Reverse steps to reinstall.

REFRIGERANT CHARGE

The correct system R-22 charge is shown on the unit
rating plate. Optimum unit performance will occur with
a refrigerant charge resulting in a suction line
temperature (6 inches from compressor) as shown in
Table 8.

TABLE 10

RATED CFM AND ESP

1

detaR

ledoM

103AW
163AW

MFC

000,1
001,1

1

detaR

PSE

04.

03.

dednemmoceR

egnaRwolfriA

003,1-039
053,1-039

1 Rated CFM and ESP on high speed tap

Manual 2100-192
Page 15

TABLE 11

MAXIMUM ESP OF OPERATION

ELECTRIC HEAT ONLY

ledoMteltuOtnorFteltuOpoT

woL

WK

00A
50A
80A
01A
51A

00B
60B
90B
51B

00C
60C
90

C

51C

deepS

05.

05.

05.

54.

53.

05.

04.

05.

03.

05.

05.

04.

53.

hgiH

deepS

05.

05.

05.

05.

04.

05.

05.

05.

54.

05.

05.

05.

54.

woL

deepS

05.

54.

---

53.

---

05.

---

04.

---

05.

---

04.

---

hgiH

deepS

05.

05.

---

05.

---

05.

---

54.

---

05.

---

54.

---

TABLE 12

COOLING PRESSURE – OUTDOOR TEMPERATURE °F

riAnruteR

ledoM

103AW

163AW

Low side pressure ± 2 psig

High side pressure ± 5 psig

Tables are based upon rated CFM (airflow) across the evaporator coil and should be
found under section titled "refrigerant charge" elsewhere in manual. If there is any doubt
as to correct charge being in the system, the charge should be removed, system evacu­ated and recharged to serial plate instructions.

erutarepmeTerusserP5708580959001501011511021521

BDged57

BWged26

BDged08

BWged76

BDged58

BWged27

BDged57

BWged26

BDged08

BWged76

BDged58

BWged27

ediSwoL

ediShgiH

ediSwoL

ediShgiH

ediSwoL

ediShgiH

ediSwoL

ediShgiH

ediSwoL

ediShgiH

ediSwoL

ediShgiH

47

77

97

18

28

48

812

232

742

262

772

292

08

28

48

68

88

98

322

832

352

862

482

003

58

88

19

39

59

69

132

642

262

872

492

013

07

27

47

67

87

97

422

242

952

572

092

403

57

77

97

18

38

58

922

842

562

272

792

08

38

58

78

98

832

752

572

292

703

113
19

223

58

58

68

78

88

603

523

143

753

373

19

19

29

39

49

613

333

053

663

383

79

69

99

001

101

723

543

263

973

693

08

18

28

38

48

613

823

933

153

363

68

78

88

98

09

523

733

843

063

373

29

49

59

69

89

633

943

063

373

683

Manual 2100-192
Page 16

TABLE 13

OPTIONAL ACCESSORIES

LEDOMNOITPIRCSED

50A-30AWHE
80A-30AWHE
01A-30AWHE
51A-30AWHE
60B-30AWHE
90B-30AWHE
51B-30AWHE

60C-30AWHE
90C-30AWHE
21C-30AWHE
51C-30AWHE

3-POBetalPffOknalB XXXXXX

3-DAFBrepmaDriAhserFcirtemoraB XXXXXX

3-DAFMrepmaDriAhserFdezirotoM XXXXXX

3-VRCtsuahxEhtiwrotalitneVlaicremmoC

3-MFIEtsuahxEhtiwrezimonocE XXXXXX

B3A-VREWrotalitneVyrevoceRygrenEXXXX
B3C-VREWrotalitneVyrevoceRygrenEXX

5-AMC)RDT(yaleRyaleDemiT
6-AMClortnoCtneibmAwoLXXXX
8-AMCCPH+RDT XXXXXX

01-AMCRDT+CPH+CPL XXXXXX
31-AMCCAL+RDT+CPH+CPLXXXX
51-CMCtiKtratSXX

A50-BCMWtiKrekaerBtiucriCX
B20-BCMWtiKrekaerBtiucriCX
C10-DPMWtiKtcennocsiDlluPXX
B30-BCMWtiKrekaerBtiucriC X

egakcaPretaeH s
egakcaPretaeH s

egakcaPretaeH s

egakcaPretaeH s

egakcaPretaeH s

segakcaPretaeH

1

segakcaPretaeH

1

1

1

segakcaPretaeH

1

segakcaPretaeH

1

1

segakcaPretaeH

1

1

segakcaPretaeH

1

1

WA301-A

XX
XX
XX
XX

XXXXXX

XXXXXX

WA301-B

XX
XX
XX

WA301-C

XX
XX

XX

WA361-A

X

WA361-B

WA361-C

X

Manual 2100-192
Page 17