XDS-100
Safety manual
R9898490
R59770579/00
07/07/2010
Barco nv Simulation Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.36.84.86
E-mail: info@barco.com
Visit us at the web: www.barco.com
Printed in Belgium
1. Safety instructions
1. SAFETY INSTRUC TIONS
About this chapter
It is necessary to read this chapter prior to starting any activity on the device. It contains valuable and critical information to ensure
safety of the operator, other people in the neighborhood of the device.
Overview
• Notice on safety
• Installation instructions
• Owner’s record
• Warnings
• Plug types
• Heat and fire hazard
• Installation
• Prevent personal injury
• Device damage
• Environment condition check
• Service
• Cleaning
• Repacking
1.1 Notice on safety
Notice on Safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1,
UL60950-1 and CAN/CSA - C22.2 No.60950-1, which are the safety standards of information technology equipment including
electrical business equipment. These safety standards impose important requirements on the use of safety critical components,
materials and isolation, in order to protect the user or operator against risk of electric shock and energy hazard, and having access
to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability
and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the
safety of the equipment to the user even when the equipment’s normal operation fails.
1.2 Installation instructions
Installation Instructions
• Before operating this equipment please read this manual thoroughly, and retain it for future reference.
• Installation and preliminary adjustments can be performed after reading the documentation manuals in detail.
• All warnings on the device and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
1.3 Owner’s record
Owner’s Record
The part number and serial number can be found on the label at the back side of the device. Record these numbers in the table
below. Refer to them whenever you call your Barco dealer regarding this product.
Part Number:
Serial Number:
Dealer:
R59770579 XDS-100 07/07/2010 1
1. Safety instructions
1.4 Warnings
Safety warnings
• To prevent fire or electrical shock hazard, do not expose this equipment to rain or moisture!
• This product should be operated from an AC power source. Power input is auto-ranging from 100 V to 240 V.
• All equipment in the system is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin. This plug will only
fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
• If an extension cord is used with this product, make sure that the total of the Ampere ratings on the products plugged into the
extension cord does not exceed the extension cord Ampere rating.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it
checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
1.5 Plug types
WARNING: This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If the
supplied power cable is not the correct one, consult your dealer.
Plug types
a. Mains lead (AC Power cord) w ith CEE 7 plug up to 16 A
CEE 7
E
L
N
Image 1-1
The colors of the mains lead are colored in accordance with the following code:
Green + yellow: Earth (Ground)
Blue: Neutral
Brown: Line (Live)
b. PowercordwithNEMA5/15plugupto15A
NEMA 5/15
E
L
N
Image 1-2
The wires of the power cord are colored in accordance with the following code.
Green or yellow + green: Earth (Ground)
Blue or white: Neutral
Brown or black: Line (Live)
2
R59770579 XDS-100 07/07/2010
1. Safety instructions
1.6 Heat and fire hazard
Heat and Fire Hazard
Warning – risk of fire: do not place flammable or combustible materials near the device!
Barco products are designed and manufactured to meet the most stringent safety regulations.
This device radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and
safe. Exposing flammable or combustible materials into close proximity of this device could result in the spontaneous ignition of that
material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” aro
the device where no flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16”) for all
Barco devices. Do not cover the device or the lens with any material while the it is in operation.
Keep flammable and combustible materials away from the device at all times.
Mount the device in a well ventilated area away from sources of ignition and out of direct sun light.
Never expose the device to rain or moisture.
In the event of fire, use sand, CO2, or dry powder fire extinguishers; never use water on an electrical fire.
Always have service performed on this device by authorized Barco service personnel.
Always insist on original Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this
device.
Slots and openings in the cabinet and the sides are provided for ventilation; to ensure reliable operation of the device and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface.
This device should never be placed near or over a radiator or heat register, no
unless proper ventilation is provided.
Rooms must be well ventilated or cooled in order to avoid build up of heat.
r should it be placed in a built-in installation or enclosure
und all external surfaces of
1.7 Installation
Safety On Installation
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it.
• Do not use this equipment near water.
• Only use the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
• Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not
placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or
heat register, nor should it be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Do not block the device’s cooling fans or free air movement around the device. Loose papers or other objects may not be
nearer to the device than 10 cm (or 4") on any side.
• Always ensure the working load limit of the structure supporting the device.
be blocked or covered. The openings should never be blocked by
1.8 Prevent personal injury
To prevent personal injury
To prevent injuries and physical damage, always read this manual and all labels on the system before connecting to the wall outlet.
To prevent injuries, take note of the weight of the device.
Before attempting to remove any of the device’s covers, you must turn off the device and disconnect from the wall outlet.
1.9 Device damage
To prevent device damage
In order to ensure that correct airflow is maintained, and that the device complies with Electro-Magnetic Compatibility requirements,
it should always be operated with all of it’s covers in place.
Ensure that nothing can be spilled on, or dropped inside the device. If this does happen, switch off and unplug the mains supply
immediately. Do not operate the device again until it has been checked by qualified service personnel.
R59770579 XDS-100 07/07/2010
3
1. Safety instructions
The device must always be mounted in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the
hot air exhausted from its cooling system. Heat sensitive materials should not be placed in the path of the exhausted air.
1.10 Environment condition check
Environment condition check
A device must always be mounted in a manner which ensures the free flow of clean air into the device’s venti
installations in environments where the device is subject to excessive dust, then it is highly advisable and desirable to have this dust
removed prior to it reaching the device clean air supply. Devices or structures to extract or shield excessive dust well away from the
device are a prerequisite; if this is not a feasible solution then measures to relocate the device
considered.
It is the clients responsibility to ensure at all times that the device is protected from the harmful effects of hostile airborne particles
in the environment of the device. The manufacturer reserves the right to refuse repair if a device has been subject to negligence,
abandon or improper use.
to a clean air environment should be
Ambient temperature conditions
Max. ambient temperature : +40°C or 104°F
Min. ambient temperature : -5°C or 41°F
Storage temperature: -35°C to +65°C (–31°F to 149°F)
Humidity Conditions
Storage: 0 to 98% relative humidity, non-condensing
Operation: 0 to 95% relative humidity, non-condensing
lation inlets. For
Environment
Do not install the device in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive
dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive.
Environment condition check
The device must always be mounted in a manner which ensures the free flow of clean air into the air intake and out of the air outlet.
1.11 Service
Safety On Servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and
risk of electric shock!
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the equipment.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
• If the product has been dropped or the cabinet has been damaged.
• If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original BARCO replacement parts or authorized replacement parts whic
substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
• Safety check: Upon completion of any service or repairs to this device, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
h have the same characteristics as the BARCO original part. Unauthorized
4
R59770579 XDS-100 07/07/2010
1. Safety instructions
1.12 Cleaning
Safety On Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly
dampened with mild detergent solution. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these
will damage the cabinet.
1.13 Repacking
On Repacking
Save the original shipping carton and packing material; they will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.
R59770579 XDS-100 07/07/2010
5
Loading...