Barco Wodan, HDX 4K User Manual

Download

Page 1

Wodan

R5906102/00 15/02/2017

User manual

Page 2

Barco NV Beneluxpark 21, 8500 Kortrijk, Belgium Phone: +32 56.23.32.11 Fax: +32 56.26.22.62 Support: www.barco.com/en/support Visit us at the web: www.barco.com

Registered address: Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium Phone: +32 56.23.32.11 Fax: +32 56.26.22.62 Support: www.barco.com/en/support Visit us at the web: www.barco.com

Printed in Belgium

Page 3

EN55022/CISPR22 Class A ITE (Information Technology Equipment)

Class A ITE is a category of all other ITE which satisﬁes the class A ITE limits but not the class B IT E limits. Such equipm ent should not be restricted in its sale but the following warning shall be included in the instructions for use:

Warning : This is a class A product. In a domestic environment this product may cause radio interference in whic h case the user may be required to take adequate measures. Contact the installer.

Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply w ith the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in a ccordance with the instruction manual, may c ause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case t he user will be responsible for correcting any interference at his own expense

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user ’s authority to operate the equipment

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war ranties or merchantability and ﬁtness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time w ithout notice.

This publication could c ontain technical inaccuracies or typograp publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals c an be downloaded from the Barco web site w

ttps://www.barco.com/en/signin.

hical errors. Changes are periodically made to the information in this

ww.barco.com or from the secured Barco web site

All rights r eserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as commen ts or examples and are not to be understood as advertising for the products or their manufacturers.

Page 4

Page 5

Table of contents

TABLE OF CONTENTS

1. Safety................................................................................................................ 3

1.1 General considerations .............................................................................................................. 3

1.2 Safety training to be provided by the installer ...................................................................................... 4

1.3 Important safety instructions ........................................................................................................ 4

1.4 High Brightness precautions: Hazard Distance (HD) .............................................................................. 7

1.5 HD for fully enclosed projection systems ........................................................................................... 8

1.6 HD infunction of modifying optics .................................................................................................. 9

2. Remote Control Unit ................. ................ ................ ................ ................ .............11

2.1 Remote control, Battery installation.................................................................................................11

2.2 Using the XLR connector of the RCU...............................................................................................12

3. Input & Communication ..........................................................................................13

3.1 Introduction ..........................................................................................................................13

3.2 Input source connections . .. .........................................................................................................13

3.3 Communication connections ........................................................................................................ 18

3.4 LED and Button indication chart .................................................................................................... 19

4. Getting Started................ ................ ................ ................ ................ .................. ...21

4.1 Functionality overview ...............................................................................................................21

4.2 Power on projector ..................................................................................................................22

4.3 Switching to standby ................................................................................................................ 24

4.4 Power off projector ..................................................................................................................24

4.5 Using the RCU.......................................................................................................................25

4.6 Quick setup via Direct access.......................................................................................................26

5. Graphic User Interface (GUI) ....................................................................................29

5.1 Overview.............................................................................................................................29

5.2 Navigation ...........................................................................................................................29

5.3 Test Patterns.........................................................................................................................30

6. Basic operations ..................................................................................................33

6.1 Source Selection .................................................................................................................... 33

6.2 Connector Settings .................................................................................................................. 33

6.3 Setting image levels manually ......................................................................................................34

6.4 Setting the output resolution ........................................................................................................ 36

6.5 Lamp illumination....................................................................................................................37

6.6 Themes ..............................................................................................................................38

7. Advanced operations.. ................ ................ ................ ................ ................ ...........39

7.1 P7 Realcolor......................................................................................................................... 39

7.2 Conﬁguring the lens .................................................................................................................40

7.3 Orientation...........................................................................................................................42

7.4 Warping ..............................................................................................................................42

7.4.1 About warping.................................................................................................................42

7.4.2 Warping – Screen Size ....................................................................................................... 42

7.4.3 Warping – 4 cornersadjustment..............................................................................................43

7.5 Blending..............................................................................................................................45

7.5.1 Blend Zones. . .................................................................................................................45

7.6 Communication ......................................................................................................................47

7.6.1 Introduction to a Network connection ........................................................................................47

7.6.2 Wired IP address set up ...................................................................................................... 48

7.7 Service Menu ........................................................................................................................50

7.7.1 Service – Color................................................................................................................50

7.7.2 Service – Statistics............................................................................................................51

7.7.3 Lens Calibration...............................................................................................................52

7.8 Reset.................................................................................................................................53

8. Maintenance........... ................ ................ ................ ................ ................ .............55

8.1 Cleaning the lens . .. .................................................................................................................55

8.2 Cleaning the exterior of the projector ............................................................................................... 55

9. Speciﬁcations......................................................................................................57

9.1 Dimensions of a Wodan .............................................................................................................57

9.2 Technical Regulations ...............................................................................................................57

10. Environmental Information ......................................................................................59

10.1 Disposalinformation.................................................................................................................59

10.2 China RoHS compliance ............................................................................................................59

10.3 TurkeyRoHS compliance ........................................................................................................... 60

10.4 Production address . ................................................................................................................. 61

10.5 Contact information..................................................................................................................61

R5906102 WODAN 15/02/2017

Page 6

Table of contents

2 R5906102 WODAN 15/02/2017

Page 7

1. SAFETY

Clariﬁcation of the term “Wodan” used in this document

When referring in this document to the term “Wodan” means that the content is applicable for following Barco products:

• Wodan

Model certiﬁcation name

• HDX 4K

Overview

• General considerations

• Safety training to be provided by the installer

• Important safety instructions

• High Brightness precautions: Hazard Distance (HD)

• HD for fully enclosed projection systems

• HD in function of modifying optics

1.1 General considerations

1. Safety

WARNING: Be aware of suspended loads.

WARNING: Wear a h ard h at to reduce the risk o f person al injury.

WARNING: Be careful while working with heavy loads.

WARNING: Mind your ﬁngers while working with heavy loads.

General safety i nstructions

• Before operating this equipment please read this manual thoroughly and retain it for future reference.

• Installation and preliminary adjustments should be performed by qualiﬁed Barco personnel o r by authorized Barco service dealers.

• All warnings on the pr ojector and in the documentation manuals should be adhered to.

• All instructions for operating and use of this equipment m ust be followed precisely.

• All local installation codes should be adhered to.

Notice on safety

This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including electrical business equipmen t. These safety standards impose important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction an d protection against the risk of ﬁre. Simulated single fault condition testing ensures the safety of the equipm ent to the user even when the equipment’s normal operation fails.

R5906102 WODAN 15/02/2017

Page 8

1. Safety

1.2 Safety training to be provided by the installer

WARNING: The installer is responsible that the user is instructed. The user w ill sign a document to conﬁrm

that the instructions have been received and understood.

Users deﬁnition

The Wodan projector is intended for persons who have been instructed and trained by a skilled person (installer or service personnel) to identify energy sources that may cause injury and to take precautions to a void unintentional contact with or exposure to those energy sources.

The skilled person must instruct the us er about:

• High intensity light beam. The user must respect the exclusion zone, based on the light beam Hazard Distance (HD).

• Dangerous energy sources inside the projector. The user is n ot allowed to remove any cover from the projector.

• Small glass parts can leave the projector in the event of lamp explosion. Keep 1m (40 in) distance from the air outlet side of the projector during operation.

• The installation, maintenance or service is for skilled persons only.

• The requirements for a restricted access location and an exclusion zone.

Restricted access location

To protect untrained persons and children, the projector must be installed in a restricted access location. The deﬁnition of a restricted access location is a location for equipment where both of the following paragraphs apply:

• Access can only be gained by skilled persons ( installer or service personnel) or persons who have been instructed and trained by a skilled person. The persons must have been instructed about the reasons for the restriction applied to the location and about the precautions that shall be taken.

• Access is o nly possible through the use of the tool or lock and key, or other means of security, and is controlled by the authority responsible for the location.

Why a restricted acc ess location: This is a RG3 product. Based on international requirem ents, no person in allowed to enter the projected beam within the z one between the projection lens and the related Hazard Distance (HD). This shall be physically impossible by creating sufﬁcient separation height or by placing optional barriers. Within the restricted area ope rator training is considered sufﬁcient. The applicable separation heights are discussed in "High Brightness precautions: Hazard Distance (HD)", page 7 .

Exclusion zone

The projector radiates heat on its external surfaces and from ventilation ducts during normal operation. Exposing ﬂammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a

ﬁre. For this reason, it is absolutely necessa ry to leave an exclusion zone around all external surfaces of the projector whereby no ﬂammable or combus tible m aterials are present:

• The exclusion zone must not be less than 40 cm (16 in.).

• Loose papers or other objects may not be nearer to the projector than 10 cm (4 in.) on any side.

To protect untrained us ers and children against high intensity light beams, the light beam Hazard Distance (HD) shall be taken into account.

1.3 Important safety instructions

To prevent the risk of electrical shock

• This product should be operated from a mono phase AC power source. Ensure that the mains voltage and capacity matches the projector electrical ratings (110-130V/200-240V, 15A, 50-60Hz). If you are unable to install the AC requirements, contact your electrician. Do not defeat the pu rpose of the grounding.

• This a pparatus must be grounded (earthed) via the supplied 3 conductor A C power cable. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.

• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.

• Do not operate the projector with a damaged cord. Replace the cord.

• Do no t operate the projector if the projector has been dropped or damaged - until it has been examined and approved for operation by qualiﬁed service personnel.

• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

• If an extension cord is nec essary, a cord with a cur rent rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat.

R5906102 WODAN 15/02/2017

Page 9

1. Safety

• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of ﬁ re or electrical shock.

• Do not expose this projector to rain or moisture.

• Do not immerse or expose this projector in water or other liquids.

• Do not spill liquid of any kind on this projector.

• Should any liquid or solid object fall into the cabinet, unplug the set and hav e it checked by qualiﬁed service personnel before resuming operations.

• Do not disassemble this projector, always take it to qualiﬁed service personnel when service or repair work is r equired.

• Do not use an accessory attachment which is not recom mended by the manufacturer.

• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.

To prevent personal injury

• To prevent injury and phy sical damage, always read this manual and all labels on the system before powering the projector or adjusting the projector.

• To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the pr ojector. T he projector weights about ±50 kg (±111 lbs) without lens and rigging frame.

• To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.

• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.

• Warning: e xtremely high brightness lamps: This projector uses extremely high brightness lamp s. Never attempt to look directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 m eters away from the projected image. Avoid close range reﬂ ection of the projected image on any reﬂecting surface (such as glass, metal, …) . When operating the projector, we strongly recommend wearing suitable safety glasses.

• Based on international requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related Hazard Distance (HD). This shall be physically impossible by creating sufﬁcient separation height or by placing optional barriers. Within the restricted area operator training is considered sufﬁcient. The applicable separation heights are discussed in "High Brightness precautions: Hazard Distance (HD)", page 7 .

• Don’t put your hand in front of the beam.

• Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet.

• When required to switch off the projector, to access parts inside, always disconnect the pow er cord from the power net.

• The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the ﬁxed wiring.

• Never stack more than 2 Wodan projectors in a hanging c onﬁ gur ation (truss) and nev er stack more t han 3 Wodan projectors in a base stand conﬁguration (table mount).

• When using the pr ojector in a hanging c onﬁgur ation, always m ount 2 safety cables. See installation manual for the correct use of these cables.

• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user.

• It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall b e changed if they have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.

• Warning: Protection from ultraviolet radiation: Do not look dire an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. P rotect y ourself and your employees by ma king them aware of the hazards and how to pr by wearing tightly wov en garments and glov es. Protecting the eyes from UV can be accomplished by wearing safety glasses that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be considered when choosing protective eye wear.

• Exposure to UV radiation: Some medications are known to make individuals extra sens itive to UV radiation. The American Conference of Governmen tal Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV radiation is allowed for only 1 hour per day for m aintenance and service persons.

• Cooling liquid circuit. The projector contains a cooling circuit ﬁlled with Blue antifreeze diluted (1/3 ethanediol – 2/3 Demi water). When the cooling circuit leaks, switch off the device and contact qualiﬁed service personnel. The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with eyes , sk in and clothing. Avoid inhale of the noxious fumes.

• Never point or allow light to be directed on people or reﬂective objects within the HD zone.

• When the projector is mounted above persons, mo

• All operators shall have received adequate training and be aware of the potential hazards.

• In case the product malfunctions, power off the unit and c ontact Barco by logging an incident via the support website:

ww.barco.com/en/support.

unt always a lens safety cable.

ctly in the light beam. The lamp contained in this product is

otect themselves. Protecting the skin can be accomplished

R5906102 WODAN 15/02/2017

Page 10

1. Safety

To prevent ﬁre hazard

• Do not place ﬂammable or com bustible m aterials near the projector!

• Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. E xpo sing ﬂammable or combustible materials into close proximity of this projector c ould result in the spontaneous ignition of that material, resulting in a ﬁre. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the pro jector whereby no ﬂam mable or combustible m aterials are present. The exclusion zone mu st be not less than 40 cm (16”) for this projector. The ex clusion zone on the lens side must be at least 5 m. Do not cov

er the projector or the lens with any material while the projector is in operation. Keep ﬂammable and combustible materials away from the projector at all times. M ount the projector in a well ventilated area away from sources of ignition and out o f direct sun light. Never expose the projector to rain or moisture. In the event of ﬁre, use sand, CO electrical ﬁre. Always have service per formed on this projector by authorized Barco service personnel. Alway s insist on genuine

or dry powder ﬁre extingu

ishers. Never use wate r on an

Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.

• Ensure no misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) can represent a ﬁre risk. After alignment the projector shall be securely mounted to the pedestal.

• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projec tor an d to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat register. This p rojector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Projection rooms m ust be well ve ntilated or cooled in order to avoid build up of heat. It is necessary to vent hot e xhaust air from projector and cooling system to the outside of the building.

• Let the projector cool completely before storing. Remove cord from the projector when storing.

To prevent battery explosion

• Danger of explosion if battery is incorrectly installed.

• Replace only with the same or equivalent type recommended by the manufacturer.

• For disposal of used batteries, always consult federal, state, to ensure proper disposal.

local and provincial hazardous waste disposal r ules and regulations

To prevent projector damage

• This projector has been designed for use with a spe ciﬁc lamp (house) type. S ee installation instructions for its correct type.

• The air ﬁlters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum). Neglecting this could result in disrupting the air ﬂow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation.

• The projector must always be installed in a manner which ens ures free ﬂow of air into its air inlets and unimpeded evacuation of the hot air from its cooling system.

• In order to ensure that correct airﬂow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC ) requirements, it should always be operated with all of it’s covers in place.

• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the p roduct on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Ensure that nothing can be spilled on, or dropped inside the projector. If this d oes happen, switch off and unplug the mains supply immediately. Do not operate the projector again un til it has been checked by qualiﬁed service personnel.

• Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects m ay n ot be nearer to the projector than 10 cm (4") on any

• Do not use this equipment near water.

• Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices which case there is a loss of warranty.

• Never place the projector in direct sun light. Sun light on the lens can sev erely damage the Digital M irror Devices case there is a loss of warranty.

• Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.

• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, s ince these will damage the cabinet. Stubborn stains m ay be rem oved with a cloth lightly dampened with mild detergent solution.

• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reﬂective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry c loth. Do not use a damp cloth, detergent solution, or thinner.

• Rated maximum ambient temperature, t

• The lamp house shall be replaced if it has become damaged or thermally deformed.

side.

= 40°C (104°F).

in which

R5906102 WODAN 15/02/2017

Page 11

1. Safety

On servicing

• Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and risk of electric shock.

• Refer all servicing to qualiﬁed s ervice personnel.

• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty.

• Remove all power from the projector and refer servicing to qualiﬁed service technicians under the following conditions:

- When the power cord or plug is damaged or frayed.

- If liquid has been spilled into the equipment.

- If the product has been exposed to rain or water.

- If the product does not operate norm ally when the operating instructions are followed. Adjus t only those controls that are

covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualiﬁed technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has been damaged.

- If the product exhibits a distinct change in performance, indicating a need for service.

• Replacement parts: When replacement parts are r equired, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the sam e cha racteristics as the Barco original part. Unauthorized substitutions m ay result in degraded performance and reliability, ﬁre, electric shock or other h azards. Unauthorized substitutions may void warranty.

• Safety check: Upon completion of any s ervice or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

CAUTION: Xeno n co mp act arc lamps are highly pressurized. When ignited, the n orm al o perating temperature

of the bulb increases the pressure to a level at which the bulb may explode if not handled in strict accordance to the manufacturer’s instructions. The bulb is stable at room temperature, but otherwise mishandled. Whenever the lamp house, containing a xenon lamp, has to be dismantled or whenever the protective container or cloth has to be removed from the xenon lamp, authorized protective clothing M U ST be wo r n!

may still explode if dropped or

1.4 High Brightness precautions: Hazard Distance (HD)

Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or t he energy per surface unit becom es lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the

Restriction Zone (RZ) based on the HD

The HD depends on the amount of lumens p roduced by the proje of modifying optics", page 9 .

To protect untrained e nd users (as cinema v isitors) the installation shall comply with the following installation requirements: Operators shall control access to the beam within the hazard distance or install the product at the height that will prevent spectators’ eyes from being in the hazard distance. Radiation levels in excess of the limits will not be permitted at any point less than 2.0 meter (SH) above any surface upon which persons other than ope rators, performers, or employees are permitted to stand or less than 1.0 meter (SH) lateral separation from any place wher e such persons are permitted to be. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for ex ample by an individual sitting on another individual’s sho ulders, within the HD.

These va lues are minimum values and are based on the guidance provided in IEC 62471-5:2015 section 6.6.5.

The end user m ust understand the risk and apply protective measures based upon the haz ard distance as indicated on the label and in the user information. Installation method, barriers, detection system or other applicable control m easu re shall prevent hazardous eye access to the radiation within t he hazard distance.

For example, projectors that hav e a HD greater than 1 m and emit light into an uncontrolled area where persons may be present should be positioned in accordance wit the audience area unless the beam is at least 2.0 meter above the ﬂoor level. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individ separation height may be achieved by mounting the image projector on the ceiling or through the use of physical barriers.

For applications installed in the USA market the above limits do not apply. The relevant minimum separation height is 2.5 meter (8.2 ft) and the separation w idth is deﬁned as 1.0 meter (3.3 ft) by the FDA CDRH.

h“theﬁxed projector installation” parameters, resulting in a HD that does not extend into

ual sitting on another individual’s shoulders, within the HD. For example, a sufﬁciently large

ctor and the type of lens installed. S ee next chapter"HD in function

light source is less than the HD.

R5906102 WODAN 15/02/2017

Page 12

1. Safety

RA TH

Image 1-1 ASideview. B Top view. RA Restricted Access location (boot area of projector). PR Projector. TH Theater. RZ Restriction Zone in the theater. SH Separation Height. SW Separation Width.

Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related hazard distance (HD). This s hall be ph The minimum separation height takes into account the surface upon which persons other than operator, performers or employees are permitted to stand.

On image 1-2 a typical setup is displayed. It must be veriﬁed if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This c an be done by using physical barrier, like a red rope as illustrated in image 1-2.

The restricted area sticker can be replaced by a sticker with only the symbol.

ysically impossible by creating sufﬁcient separation height or by placing barriers.

(B) TOP VIEW(A) SIDE VIEW

RESTRICTED

AREA

Image 1-2

1.5 HD for fully en

RESTRICTED

AREA

closed projection systems

8 R5906102 WODAN 15/02/2017

Page 13

1. Safety

Restriction Zone (RZ) based on the HD

The projector is also suitable for rear projection applications; projecting a beam onto a defuse coated projection screen. As display ed in image 1-3 two areas should be considered: the restricted enclosed projection area (RA) and the observation area ( TH ).

RESTRICTED

RA TH

AREA

RESTRICTED

AREA

HDDIFFUSE

REFLECTION

reﬂection

); also taking into account a 1 meter lateral

Image 1-3 RA Restricted Access location (enclosed projection area). PR Projector. TH Theater (observation area). RZ Restriction Zone. PD Projection Distance. SW Separation Width. Must be minimum 1 meter.

For this type of setup 3 different HD sh all be considered:

• HD as discussed in "High Brightness precautions: Hazard Distance (HD)", page 7 , relevant for intrabeam exposure.

•HD

: the distance that has to be kept restrictive related to the reﬂected light from the rear projection screen.

reﬂection

: the relevant distance to be considered while observing the defuse surface of the rear projection screen.

diffuse

As described in "High Brightness precautions: Hazard Distance (HD)", page 7 , it is mandatory to create a r estricted z one within the beam areas closer than any NOHD. In the enclosed p

rojection area the combination of two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to the rear reﬂection from the screen (HD separation.

The HD projection screen. To determine the HD distance for the used lens and projector model see graphs in chapter "HD in function of

distance equals 25% of the difference between the determined HD distance and the p rojection distance to the rear

reﬂection

modifying optics", page 9 .

reflection

= 25% (HD – PD)

The light emitted from the screen within the observation shall never exceed the RG2 exposure limit, determined at 10 cm. The HD

can b e neglected if the measured light at the screen surface is below 5000 cd/m² or 15000 LUX.

diffuse

1.6 HD in function of modifying optics

TR (Th r ow Ratio)

The ratio of the distance to th

R5906102 WODAN 15/02/2017 9

e screen (throw) to the screen width.

Page 14

1. Safety

Hazard Distance

HD [m]

0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 5,0 5,5 6,0 6,5 7,0 7,5 8,0 8,5 9,0 10,0

Image 1-4 HD (in meter) in function of the Throw Ratio (TR)

10 R5906102 WODAN 15/02/2017

Page 15

2. Remote Control Unit

2. REMOTE CONTROL UNIT

2.1 Remote control, Battery installation

Where to ﬁnd the batteries for the remote control ?

The batteries are not placed in the rem ote control unit to avoid control operation in its pac kage, r time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your rem ote control, install the batteries ﬁrst.

How to install

1. P ush the battery cover tab with the ﬁngernail a little backwards (1) and pull, at the same time, the cover upwards (2).

esulting in a shorter battery life

Image 2-1

2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.

Image 2-2

3. Insert (1) both lower tabs of the battery cover in the gaps at the bottom of the remote control, and press (2) the cover until it clicks

in place.

Image 2-3

CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the

battery is replaced with an incorrect type.

R5906102 WODAN 15/02/2017 11

Page 16

2. Remote Control Unit

CAUTION: Replace the battery as explained ab ove. There is a risk of exp losion if the battery is incorrectly

installed.

2.2 Using the XLR connector of the RCU

How to use the XLR connector

1. Remove the XLR cover by pulling it backwards.

Image 2-4

2. C onnect a cable with XLR plug into the XLR connector of the R CU.

3. Connect the other end of the cable with the XLR input of the p rojec

tor.

R5906102 WODAN 15/02/2017

Page 17

3. Input & Communication

3. INPUT & C OMMU NICATION

3.1 Introduction

General

The Input & Comm unication side of the projector consists of a local keypad, a communication panel, a (V&H) and a free input slots. The free input slot can be used for optional modules (e.g. Virtual & Augmented Reality Input (V &A R)).

2 3

venues & hospitality Input

Image 3-1 1 Local Keypad and touch panel 2 O ptional antenna for WiFi connection 3 O ptional antenna for GSM 4 Com munication Panel 5 Venues & Hospitality Input (V&H) 6 F ree input slot (here ﬁlled with t he V&AR module)

3.2 Input source connections

Venues & Hospitality Input (V&H)

SDI IN SDI IN/OUT

SEL

SYNC

1 2 3 4 5 6 7 8

Image 3-2

SEL

SYNC

SEL

SYNC

SEL

SYNC

SEL

SYNC SYNC

HDM I

SEL

HDBT 1

SEL

SYNC

HDBT 2

SEL

SYNC

Quad 3G SDI channel A Input

Quad 3G SDI channel B Input

Quad 3G SDI channel C Input

Quad 3G SDI channel D Input

The yellow LED lights up when valid input sync is detected.

The green LED lights up when the input is selected.

R5906102 WODAN 15/02/2017

DisplayPort Input

HDMI Input

HDBaseT Input 1

HDBaseT Input 2

Page 18

3. Input & Communication

Input speciﬁcations

HDMI

Up to 297 MHZ pixel clock

YCbCr 4:4:4

For future release

• YCbCr 4:2:2 and YCbCr 4:2:0

• 3D support

• Interlaced support

• HDCP 1.4

• HDCP 2.2

HDMI 1.4a Support for ’Deep Color’ up to 12 bit pe r c olor

Audio not supported

Video timings

640 x 480 @60 Hz

720 x 480 @60 Hz

720 x 576 @50 Hz

800 x 600 @60 Hz

1024 x 768 @60 Hz

1280 x 720 @50 Hz

1280 x 720 @60 Hz

1280 x 960 @60 Hz

1280 x 1024 @60 Hz

1400 x 1050 @60 Hz

1920 x 1080 @24 Hz

1920 x 1080 @30 Hz

1920 x 1080 @50 Hz

1920 x 1080 @60 Hz

2560 x 1600 @60 Hz

3840 x 2160 @24 Hz

3840 x 2160 @30 Hz

4096 x 2160 @24 Hz

4096 x 2160 @30 Hz

HDBase-T

Up to 297 MHz pixel clock

YCbCr 4:4:4

Audio not supported

Video timings

For future release

• YCbCr 4:2:2 and YCbCr 4:2:0

• 3D support

• Interlaced support

•HDCP1.4

640 x 480 @60 Hz

720 x 480 @60 Hz

720 x 576 @50 Hz

800 x 600 @60 Hz

1024 x 768 @60 Hz

R5906102 WODAN 15/02/2017

Page 19

HDBase-T

1280 x 720 @50 Hz

1280 x 720 @60 Hz

1280 x 960 @60 Hz

1280 x 1024 @60 Hz

1400 x 1050 @60 Hz

1920 x 1080 @24 Hz

1920 x 1080 @30 Hz

1920 x 1080 @50 Hz

1920 x 1080 @60 Hz

2560 x 1600 @60 Hz

3840 x 2160 @24 Hz

3840 x 2160 @30 Hz

4096 x 2160 @24 Hz

4096 x 2160 @30 Hz

SDI

3G SDI follows the SMPT E 425M standard Level A

HD-SDI follows the SMPTE 292M standard

Color space YCbCr

RGB : future re lea se

Colordepth 10 bpc

12 bpc : future release

Chroma sampling 4:2:2

4:2:0 and 4:4:4 : future release

Audio support not supported

3D support

For future release

3. Input & Communication

Video timings Progressive

Up to 600 MHz pixel clock

YCbCr 4:4:4

• Interlaced support

• Segmented frame support

Type Port type Format

HD-SDI Single link 1280 x 720 @24 Hz

HD-SDI Single link 1280 x 720 @25 Hz

HD-SDI Single link 1280 x 720 @30 Hz

HD-SDI Single link 1280 x 720 @50 Hz

HD-SDI Single link 1280 x 720 @60 Hz

HD-SDI Single link 1920 x 1080 @24 Hz

HD-SDI Single link 1920 x 1080 @25 Hz

HD-SDI Single link 1920 x 1080 @30 Hz

3G-SDI Level A Single link 1920 x 1080 @5 0 Hz

3G-SDI Level A Single link 1920 x 1080 @6 0 Hz

R5906102 WODAN 15/02/2017

Page 20

3. Input & Communication

Audio not supported

DP 1.2

Video timings

For future release

• YCbCr 4:2:2 and YCbCr 4:2:0

• 3D support

• Interlaced support

•HDCP1.4

Support for ’Deep Color’ up to 12 bit per color

640 x 480 @60 Hz

720 x 480 @60 Hz

800 x 600 @60 Hz

1024 x 768 @60 Hz

1280 x 720 @50 Hz

1280 x 720 @60 Hz

1280 x 960 @60 Hz

1280 x 1024 @60 Hz

1400 x 1050 @60 Hz

1920 x 1080 @24 Hz

1920 x 1080 @30 Hz

1920 x 1080 @50 Hz

1920 x 1080 @60 Hz

1920 x 2160 @60 Hz

2560 x 1600 @60 Hz

3840 x 2160 @24 Hz

3840 x 2160 @30 Hz

3840 x 2160 @60 Hz

4096 x 2160 @24 Hz

4096 x 2160 @30 Hz

CAUTION: In order to display high resolut

ion images (ex.: 3840 X2160@60H z) via the DP1.2 input, the quality of the cable must be adequate, in add ition the length of the cable can also inﬂu ence the performance. In case there is an issue with one of thes e criteria the automatic link-trai ning in iti a ted by the DP-standard may dec ide to switch to a lower resolution.

CAUTION: The HDBaseT inputs can bridge a distance of 100 m but is sensitive to radiated electromagnetic

interference: radiated electromagnetic interference (e.g. from GSM or switching induc tive or ca pacitive load s) within the limits of electromagnetic compatibility requiremen ts of 3 V/m can cause random ﬂashes or temporary loss of the projected image.

As such, shielded CAT-6 cables with metal RJ-45 connectors are recommended; choose cable length no longer than required and route HDBT cable optimally screened from possible sources of electromagnetic emission.

Virtual & Augmented Reality Input (V&AR) (Optional)

DP A

SEL

SYNC

DP B

SEL

SYNC

1 2 3 4

Image 3-3

16 R5906102 WODAN 15/02/2017

DP C

SEL

SYNC

DP D

SEL

SYNC

Page 21

3. Input & Communication

Quad DisplayPort channel A Input

Quad DisplayPort channel B Input

The yellow LED lights up when valid input sync is detected.

The green LED lights up when the input is selected.

Input speciﬁcations

All inputs are DisplayPort 1.2 .

Up to 600 MHz pixel clock

YCbCr 4:4:4

For future release

• YCbCr 4:2:2 and YCbCr 4:2:0

• 3D support

• Interlaced support

•HDCP1.4

Audio not supported

DP 1.2 Support for ’Deep Color’ up to 12 bit per color

Video timings

640 x 480 @60 Hz

720 x 480 @60 Hz

800 x 600 @60 Hz

1024 x 768 @60 Hz

1280 x 720 @50 Hz

1280 x 720 @60 Hz

1280 x 960 @60 Hz

1280 x 1024 @60 Hz

1400 x 1050 @60 Hz

1920 x 1080 @24 Hz

1920 x 1080 @30 Hz

1920 x 1080 @50 Hz

1920 x 1080 @60 Hz

1920 x 2160 @60 Hz

2560 x 1600 @60 Hz

3840 x 2160 @24 Hz

3840 x 2160 @30 Hz

3840 x 2160 @60 Hz

4096 x 2160 @24 Hz

4096 x 2160 @30 Hz

Quad DisplayPort channel C Input

Quad DisplayPort channel D Input

R5906102 WODAN 15/02/2017

Page 22

3. Input & Communication

3.3 Communication connections

Communication Panel

321 4 5 6 7 8 9 10 11 12 13

Image 3-4

WIFI antenna for wireless IP ( optional)

RS232 for serial communication

12V 1A output

USB backup custom settings

10/100 base-T for external con trol over IP and Art-Net

DMX interface input

DMX interface output

XLR input for wired projector control

Sync Out

Sync In

Status lights

IR receive sensor

GSM antenna input (optional)

12V output

12 V output, maximum 1A, available w hen projector is not in s tand by.

DMX interface

DMX is used as communication bus between different devices in the light technic. Eac h device has an input and an output, so that the bus can be looped between the different devices. A ccording the standard a ﬁve wire cable with XLR connector is us ed.

You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector from that DMX device (console). The DMX output port can be connected with t he next device in the loop.

Pin Description

1Earth

2Cold

3Hot

4 Return - (or not used)

Return + (or not used)

DMX

DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting controller to lighting devices. Standardized by US ITT.

RS232/RS422 input

The communication interface of the Wodan supports R S232 and RS422 serial communication on two different types of input connectors, a Sub-D connector and an USB connector acting as RS input when connected to an USB input of a PC.

You can use the RS232/RS422 input to connect a local PC to yo ur Wodan. By this way you can conﬁgure and control y our Wodan from your local P C.

Advantages of using RS232/RS422 se rial comm unication:

• easy adjustment of the projector via PC (or MAC).

• allow storage of multiple projector conﬁgurations and set ups.

• wide range of control possibilities.

• address range from 0 to 255.

• sending data to the projector (update).

• copying data from the projector (backup).

R5906102 WODAN 15/02/2017

Page 23

Pin Description

1 DCD : Data Carrier Detect

2RXD-:ReceiveData

3 TXD- : Transmitted Data

4 DTR : Data Terminal Ready [RS232]

TXD+ : Transmitted Data [R S422]

GND : G round

6 DSR : Data S et Ready [RS232]

RXD+ : Rec eived Data [RS422]

— (not connected) —

8CTS:ClearToSend

9 RI : Ring Indicator

RS232

An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the com m unication path between two devices using either D-SU B 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and do es not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to be used. The standard speciﬁes component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < 3V. The range between -3V and +3V is the transition zone.

3. Input & Communication

RS232/422 input (Sub-D) port

RS422

An EIA serial d igital interface standard that speciﬁes the electrical characteristics of balanced (differential) voltage, digital interface circuits. This standard is usable over longer dist chronous transmission of computer data a t speeds of up to 920,000 bits per second. It is also used as the serial port standard f or Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical ’0’. When the difference is > +0.2V that equals to a logica

l’1’..

ances than RS-23 2. This signal governs the asyn-

USB port

The communication interface is equipped with a mast cedures for software updates or for taking backup ﬁles from the projector with out network connection. An USB-stick is plugged into the USB port and ﬁles can be transferred from or to the projector using the local or remote control unit. Note that the USB-stick has to be Linux FAT16 compatible.

er USB port, type “A” connector. This USB port will simplify the service pro-

3.4 LED and Button indication chart

Button Backlight Status

Button Color status Description

Standby button

Shutter button

Blinking WHITE (slow) Projector starts up (booting)

Blinking WHITE (fast) Firmware upgrade

Solid WHITE Projector is in S tandby mode

Blinking BLUE Projector goes to O N mod e

Solid BLUE Projector is ON

Blinking RED Error condition

Off (no color) Projector is OFF, starts up, or is in Standby

mode.

Solid WHITE Projector is O N, shutter is open

Solid RED Projector is ON, shutter is closed

R5906102 WODAN 15/02/2017 19

Page 24

3. Input & Communication

LED Status

LED Color status Description

PWR (power LED)

LIGHT (Illumination LED)

ERR (error LED)

Off Projector powers up

RED Projector is in Standby

ORANGE Projector is Ready

GREEN Projector is on

Off Lamp is off

RED No lamp inserted

ORANGE Lamp is on in ECO mode

GREEN Lamp is on in normal mode

GREEN-ORANGE Lamp is on in CLO mode

Off No error

RED toggles on/off Error

ORANGE toggles on/off Warning

RED IR signal receivedIR

GREEN IR signal acknowledged

20 R5906102 WODAN 15/02/2017

Page 25

4. Getting Started

4. GETTING STARTED

How controlling the projector ?

The projector can be controlled by the local keypad, by the remote control unit or by browser application.

Location of the local keypad ?

The local keypad is located on the input side of the projector.

Remote control functions.

This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up.

Other functions of the remote control are :

• switching between stand by and operational m ode.

• switching to "pause" (blanked picture, full power for immediate restarting)

• direct access to all c onnected sources.

Overview

• Functionality overview

• Power on projector

• Switching to standby

• Power off projector

• Using the RCU

• Quick setup via Direct access

4.1 Functionality overview

Local Keypad overview

Menu Selection.

Menu Activation, OK button

OSD On/Off.

Menu Back.

Power On/Off.

Touch Panel On/Off.

Input Selection.

Shutter O pen/Close.

Test P atterns.

Lens Menu.

Touch Panel.

The Keypad gives direct access to several functions, in addition to access to the m enu system.

The keypad has a back light that can be switched on and off manually. The light turns off automatically after a preselected time.

The keys are equipped with white and blue backlit LEDs. Power button is equipped with white, blue and red backlit. The L EDs are controlled according to the features available.

1 2 3 4 5 6

1011 9 8 7

R5906102 WODAN 15/02/2017

Page 26

4. Getting Started

Remote Control Unit buttons

Button pressed indicator.

Shutter Open.

Shutter Close.

Touch P anel On/Off.

OSD On/Off.

Lens Zoom.

Lens Shift.

Menu Activation.

Menu Selection, OK button.

Menu Navigation.

Input Selection.

Address button.

Numeric buttons.

XLR connector.

Macro button.

Menu Back.

Default button.

Lens Focus.

Color On/Off.

Test P atterns.

Power On.

Power Off.

Stereo Jack.

RCU On/Off.

2423

The projector re mote control is a full feature wireless remote control, powered by two (2) standard AA batteries. The battery compartment is on the back side of the remote control.

The remote control is backlit for use in dark environments. It also has an XLR c onnector for wired connection to the pr ojector. When the wire is connected, the IR beam is switched off.

LCD panel

The LCD panel has two main functions:

1. Showing the menus and adjustment information. and also a mirror of the OS D, (On Screen Display) desc ribed in User Interface when this is enabled.

2. Information regarding the status of the projector showing this data:

- Projector status

- Network address

- Active source

- Current ﬁrmware version

- Operation Data

- Active functions (Enabled Functions).

Toggle between the two indications by using the Menu button on the keypad, or on the remote control

The LCD Display will fade out 30 seconds after the las t key operation.

4.2 Power on projector

How to power on.

1. P ress the m a ins switch at the back of the projector to switch on this projector.

R5906102 WODAN 15/02/2017

Page 27

4. Getting Started

Image 4-1 Main switc h

- When ’0’ is pressed, the projector is switched off.

- W hen ’I’ is pressed, the projector is switched on.

The projector starts up to standby mode. The Power on/off button will blink until standby mode is achieved. Once in standby mode, the Power on/off button will be lit WHITE, but the display w

2. P ress the Powe r on/ off button on the projector, or the Power On button on the remote control.

The projector will continue to power on mode. The Power on/off button will blink until the projector is read y. Onc e the projector is ready, the Power button will be lit BLUE.

The start up screen is displayed on the touch panel and when fully started up, it changes to the ov erview screen.

ill be off.

Image 4-2

The current mains input voltage is indicated on the voltmeter just above the power switch.

The bac kground image of the st artup screen and info screens can be changed with Projector Toolset with an installed Pulseplug-in.

Status overview

Once the projector is s tarted, press Status to get an overview of parameters such as :

R5906102 WODAN 15/02/2017

Page 28

4. Getting Started

• Chosen source

• Current resolution and refresh r ate

• Device serial number and article number

• Current ﬁrmware version and model name

• Current illumination (in percentage)

• Lamp runtime in hours

• Chosen communication method and IP address (if connected)

•Warpstatus

• Environmental temperature

Starting image projection

1. M ake sure the available sources are connected to the app ropriate input ports.

Tip: If properly connected, the “SYN C” LED will lit up ORANGE.

2. P ress the Input Selection button on the keypad or on the remote control until:

- the LED of the selected source (the “SEL” LED) lit up G R EEN, and

- the image of the selected source is projected.

1 2

Image 4-3

4.3 Switching to standby

How to switch to standby

1. P ress and hold the Pow e r on/off b utton for 3 seconds on the local keypad, or press the Power Off button on the remote control.

The projector goes to standby mode. The after-cooling cycle will start (up to 300 seconds). During this period the P ower on/off button will blink. Once the after-cooling cy cle has ended, the projector will be in standby mode and the Power on/off button will be lit WHITE.

3 s

300 s

Image 4-4

4.4 Power off projector

CAUTION: This proced ure assu mes the pro jector is in standby mode.

24 R5906102 WODAN 15/02/2017

Page 29

How to power off

1. S witch off the projector with the mains switch. ’0’ m ust be pressed.

Image 4-5

2. U nplug the power cord from the projector.

4.5 Using the RCU

Pointing to the reﬂective screen

1. P oint the front of the RCU to the reﬂective screen surface.

4. Getting Started

AD J

TR EB

HTN

NTR

Image 4-6 IR control via reﬂective screen

Hardwired to the XLR input

1. P lug one end of the remote cable in the connector on the bo ttom of the RCU.

2. P lug the other end in the big connector on the communication interface of the projector, labelled Remote CTRL.

Pointing directly to the IR sensor

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light s trikes the sensor window or if there are obstacles b etween the remote control unit and the projector IR sensor.

R5906102 WODAN 15/02/2017

Page 30

4. Getting Started

Image 4-7 RCU to one of the IR sensors

45°

EX I

TER

US E

PH AS

SH A

R EB

45°

3 F

TE R

A U

PH AS

CO L

BR IG

EB LE

45°

F3 F

AD J

NT R

TR EB

BA LA

4.6 Quick setup via Direct access

Quick source selection

1. P ress the Input button o n the remote c ontrol or local key

Image 4-8

pad.

26 R5906102 WODAN 15/02/2017

Page 31

The source selection menu opens.

Image 4-9 Input selection

2. Use the arrow keys to select the desired source.

Quick test pattern selection

1. P ress the Test pattern button on the r emote control or local keypad.

4. Getting Started

Image 4-10

A ﬁrst t est pattern will be displayed.

2. P ress a s m ay times o n that button until the des ired pattern is displayed

R5906102 WODAN 15/02/2017

Page 32

4. Getting Started

28 R5906102 WODAN 15/02/2017

Page 33

5. Graphic User Interface (GUI)

5. GRAPHIC USER INTERFACE (GUI)

Overview

•Overview

• Navigation

• Test Patterns

5.1 Overview

GUI - Main Menu overview

The projector on screen display (OSD) is the primary user interface (UI). From here, you can review and adjust all projector and display settings.

The OSD interface uses tabs to display the main men u. Each main menu contains submenus.

The OSD can be d isabled by pressing the OSD on/off button.

Image 5-1 Home menu

The projector’s software platform uses access levels what each user can do. A standard user has access to all projector functionality. Acertiﬁed service technician has also access to service me nu. T his me nu is password protected.

5.2 Navigation

Navigation via the RCU or local keypad

Navigating the O SD can be done using the remote control or the local keypad.

1 4

2 3

3 2 1

Image 5-2

To start up the menu s tructure, p ress ME NU (1).

R5906102 WODAN 15/02/2017

Page 34

5. Graphic User Interface (GUI)

Use the arrow keys (Menu Navigation buttons) to navigate to the desired menu item (2). The background color changes to light blue.

Press the Menu Selection button (center key of the arrow keys), also c alled OK button, to activate that item a nd to jump one level deeper (3).

Use the n umeral keys to enter values, or use the arrow keys to move the barscale up or down.

Press the Back button to go up one level ( 4).

Image 5-3 Home menu

Deﬁne values

Menu settings are displayed using checkboxes, barscale sliders, and drop-down lists.

To set a value:

•PressOK to select or deselect a checkbox (turn a function O N or OF F).

• Use the arrow keys to move the bar scale slider up or down on the value line. For a bar scale 0-9, each step will equal 10% of the total value.

• To enter the value as a direct number, press ENTER, input the digit(s), and then press ENTER again to execute and exit cursor mode e.g. EN TER 79 ENTER.

Changes to values are implemented dynamically.

Menu memory

The OSD menu remembers the last selected sub–item as long as the projector is running. The menu m emo ry is reset when restarting the projector from standby.

5.3 Test Patterns

How to use test patterns

1. In the main menu, select Test Patterns.

Or, Push the Test Patterns button on the RC or on the local keypad.

Image 5-4 Main menu, Test Patterns

2. In the Test Patterns menu, select either Internal,orOutput test patterns.

3. In the ch osen submenu, select the desired test pattern from the list.

You can select one of the following Intern

al test patterns:

R5906102 WODAN 15/02/2017

Page 35

- Co lor bars

- Ch ecker board

- B lue / Green / Red / White

- Co nvergence 1 / 2

-Focus

- Aspec t

- Focu s green

- Cross hatch

- M ono scope

- FRHL

- Ansi lumen

You can select one of the following Output test patterns:

- Vertical / diagonal lines

- Step bar

- B le m ish zone

- Ch eckerboard

- Co lor bars

- Co nvergence

-FIP

- Full s creen black / white / blue / green / red / cyan / magenta / yellow

-Grid

- Vertical Ramp

- Ho rizontal Ramp

-MTF

4. To turn the test pattern off, return to the previous menu.

5. Graphic User Interface (GUI)

R5906102 WODAN 15/02/2017

Page 36

5. Graphic User Interface (GUI)

32 R5906102 WODAN 15/02/2017

Page 37

6. BASIC OPERATIONS

Overview

• Source Selection

• Connector Settings

• Setting image levels manually

• Setting the output resolution

• Lamp illumination

• Themes

6.1 Source Selection

How to select?

1. P ress Menu to activate the men us and select Source.

6. Basic operations

Image 6-1 Select Source

2. P ress ENTER.

The Select Source menu is displayed with the actual available sources ﬁ lled out.

Image 6-2 Input selection

3. S elect the desired input.

6.2 Connector Settings

How to conﬁgure the connector

1. P ress Menu to activate the men us and select Source.

R5906102 WODAN 15/02/2017

Page 38

6. Basic operations

Image 6-3 Select Source

2. P ress ENTER.

The Select Source menu is displayed with the actual available sources ﬁ lled out.

3. S croll down to the bottom of the list and select Connector Settings.

Image 6-4

The available sources are displayed.

Image 6-5 Select source

4. S elect the desired connector.

The Connector Settings menu for this connector will be displayed. All default values are Auto.

Image 6-6

5. To apply a limit on the used co lor space, select one of the other values in Color space.

6. To apply a limit on the used signal range, select one of the other ranges in Signal Range.

6.3 Setting image levels manually

Purpose

Contrast: Change the contrast of the complete output signal (main and PiP window together) of the projected image.

R5906102 WODAN 15/02/2017

Page 39

6. Basic operations

Brightness: Change the brightness of the complete output signal (main and PiP window together) of the projected image.

Saturation: Change the saturation of the complete output signal (main and PiP window together) of the projected image.

How to set up Contrast

1. In the main menu, select Image → Contrast.

Image 6-7 Image menu — Contrast

2. U se the ◄ or ► key to c hange the contrast enhancement until the desired value is reached (adjustable between 0 and 2).

Image 6-8 Contrast slider

3. U se the ▲ or ▼ key to select Saturation or Brightness.

Or, go to Home - Image and select Saturation or Brightness.

How to set up Brightness Level

1. In the main menu, select Image → Brightness.

Image 6-9 Image menu — Brightness

2. U se the ◄ or ► key to change the brightness until the desired value is reache d (adjustable between –1 and 1).

R5906102 WODAN 15/02/2017

Page 40

6. Basic operations

Image 6-10 Brightness slider

3. U se the ▲ or ▼ key to select Contrast or Saturation.

Or, go to Home - Image and select Contrast or Saturation.

How to set up Saturation Level

1. In the main menu, select Image → Saturation.

Image 6-11 Image menu — Saturation

2. U se the ◄ or ► key to change the saturation until the desired value is reached (adjustable between -1 and 1).

Image 6-12 Saturation slider

3. U se the ▲ or ▼ key to select Brightness or Contrast.

Or, go to Home - Image and select Brightness or Contrast.

6.4 Setting the output resolution

How to choose the output resolution

1. In the main menu, select Image → A

dvanced → Output resolution.

R5906102 WODAN 15/02/2017

Page 41

Image 6-13 Advanced menu — Output resolution

The current active output resolution is indicated at the bottom of the selection button.

2. S elect the desired output resolution.

Possible resolutions:

- 4K UHD: 4K images, using the actuator.

- WQ X GA : 2K images. In this m ode, the actuator is disabled.

6. Basic operations

Image 6-14 Output resolution

6.5 Lamp illumination

What can be done?

Within a certain power mode, the light output of the lamp can be reduced by reducing the lamp power

How to reduce the power

1. In the main menu, select Installation → Illumination.

Image 6-15 Installation menu, Illumination

2. In the Illumination Menu, select Power.

Image 6-16 Illumination menu, Power

The actual power setting is indicated at the bottom of the Power button.

3. Use the Slider to change the power value.

R5906102 WODAN 15/02/2017

Page 42

6. Basic operations

Image 6-17 Lamp Power Adjustm ent

6.6 Themes

About Themes

Themes a re used to apply a predeﬁned functionality to the OSD displ

ay. There are two options: light (default) or dark.

How to s elect a different interface theme

1. In the main menu, select S ystem Settings →Themes.

Image 6-18 System Settings Menu — Themes.

2. In the themes menu, selec t the desired Theme.

You can choose one of the following: Light,orDark.

R5906102 WODAN 15/02/2017

Page 43

7. Advanced operations

7. ADVANCED OPERATIONS

Overview

• P7 Realcolor

•Conﬁguring the lens

• Orientation

• Warping

• Blending

• Communication

• Service Menu

•Reset

7.1 P7 Realcolor

Purpose

When blending images from multiple projectors, the measured color coordination of each projector can be altered to a desired common level. This so that the projected colors are identical over all projectors used.

How to set the P7 desired values

1. In the main menu, select Image → Advanced → P7 Realcolor.

Image 7-1 Advanced menu — P7 Realcolor

The P7 menu is displayed.

Image 7-2 P7 Realcolor menu

2. S elect the desired Mode. Choose one of the following:

- Na tive: Default mode, with default values. All other options in the P7 menu are disabled.

- Custom RGB: 3–point color conﬁgur ation. In RG B mode, the C, M and Y coordinates will be calculated automatically based

on the R, G and B coordinates.

- Custom RGBCMY: 6–point color conﬁguration (both RGB and CMY). In RGBCMY mode, each color can be given a speciﬁc

coordinate within the measured color triangle.

- Custom WHITE:Conﬁgure only the White temperature.

3. D eﬁ ne the coordinates for each available color.

Click o n a coordinate value and select the current value. Enter the desired value with the numeric keys.

Note: You can only pick coordinates within the mea sured color triangle.

4. F or Custom White, click on W hite point and choose one of the following:

R5906102 WODAN 15/02/2017

Page 44

7. Advanced operations

- Coordinates:Conﬁ gure the white point via speciﬁc coordinates. The white point is speciﬁed using an x, y coordinate in the

CIE 1931 Chart.

- Temperature:Conﬁgure the white point via a color temperature slider. The w h ite point is speciﬁed on a Kelvin scale between

3200K and 13000K tracking along the b lack body curve.

You can reset all coordinates to the default values (to n ative) by selecting Reset m od es to native. Press OK button to reset.

7.2 Conﬁguring the lens

What can be done?

Once a lens has been installed in the projector, you can ﬁne-tune the projected image.

The following things can be conﬁgured possible:

• Correcting the lens zoom and focus.

• Shifting the lens position.

• High Contrast mode

Zoom - Focus

1. In the main menu, s elect Installation → Lens.

Image 7-3 Installation menu — Lens Options

2. To change the focus and zoom, select Zoom focus.

Image 7-4 Lens menu, Focus & Zoom

3. U se the ▲ or ▼ key to zoom the lens in or out.

Use the ◄ or ► key to focus the lens to far or near.

Image 7-5 Zoom and focus adjustment

Vertical and Horizontal Shift

1. To ch ange the position of the projected image, select Installation → Lens → Shift.

R5906102 WODAN 15/02/2017

Page 45

Image 7-6 Lens menu, Lens shift

2. U se the ▲ or ▼ key to shift the lens (image) in vertical direction.

Use the ◄ or ► key to shift the lens (image) in horizontal direction.

7. Advanced operations

Image 7-7 Shift adjustment

High Contrast

1. To (de)activate high contrast mode, select Installation → Lens → High Contrast .

Image 7-8

The actual state is indicated on the bottom of the High Contrast button.

2. Click on or off to activate / deactivate high contrast mode.

Image 7-9 High contrast ON-OFF

R5906102 WODAN 15/02/2017 41

Page 46

7. Advanced operations

7.3 Orientation

What can be done?

The way of physical installation of the projector can be deﬁ ned to the projector.

The following installation are pos sible:

• front/table

• front/ceiling

• rear/table

• rear/ceiling

How to set the correct orientation

1. In the main menu, select Installation → Orientation.

Image 7-10 Installation menu, Orientation

The Orientation menu is displayed.

Image 7-11 Orientation menu

2. U se the ▲ or ▼ key to select the desired mounting position and press OK button to activate.

Use the ▲ or ▼ key to select the desired projection position and press OK button to activate.

7.4 Warping

7.4.1 About warping

Overview

Image warping is the process of digitally manipulating an image to compensate for the distortion of the screen. Consequently, it can also be used to generate an image with irregular shape.

While an im age can be transformed in various ways, pure warping doesn’t affect the colors.

7.4.2 Warping – Screen Size

About Screen Size adjustment

If the used screen or projected area is not a standard size, you can adjust the projected image to perfectly ﬁt the s creen/area.

Note that Screen Size adjustment is not the same as zooming in or out. If an non-standard screen/area is used, it is better to ﬁrst use the Zoom and focus functions to match the projected image to the target area as closely as possible. Only after this is done, you can shrink either the width or height to obtain a perfect match.

R5906102 WODAN 15/02/2017

Page 47

How to adjust the image?

1. In the main menu, se lect Installation → Warp.

Image 7-12 Installation menu, Warp

2. In the Warp menu, select Screen Size.

Image 7-13 Warp Me nu, Sc ree n S ize

The Screen S ize menu is displayed.

7. Advanced operations

Image 7-14 Screen Size menu

3. S elect either Screen width or Screen height.

4. S et the new v alue to shrink either the width or height of the projected image and conﬁrm.

Tip: A red border corner will be projected along with the current image. The border is a visual aid, showing the result of the

adjusted screen size.

5. Click Apply.

7.4.3 Warping – 4 corners adjustment

About 4 Corners adjustment

4 corner adjustment is typically used when the mechanical installation of the projector prevents it from pointing perpendicularly at the screen. For example, you ca n overshoot the screen and use 4 corner adjustment to pull your projected im age corners bac k into the screen.

Some examples:

R5906102 WODAN 15/02/2017 43

Page 48

7. Advanced operations

Image 7-15 4 corner adjustment

How to adjust the image?

1. In the main menu, se lect Installation → Warp.

Image 7-16 Installation menu, Warp

2. In the Warp menu, select 4Cor ners.

Image 7-17 Warp menu, 4Corners

The 4Corners m enu is displayed.

Image 7-18 4Corners Warpin g

3. To enable warping, make sure the Warp slider is set to On.

The slider is enabled when set to th e right an d when it is colored blue.

4. To set warping on one or m ore of the four corners, select one of the four corners.

5. S et the des ired X and Y coordinates for this c orner, using the arrow keys.

Tip: A red border corner will be projected along with the current image. The border is a visual aid, showing the result of the

warped co rn ers.

6. Repeat from step 4 for each corner, until all corners ar e warped in the desired position.

R5906102 WODAN 15/02/2017

Page 49

7. Advanced operations

The reset the 4 corner adjustments, select Reset and press the OK button.

7.5 Blending

About Blending

Blending is used in multi channel installation to have a seamless transition between the channels. Image blending gives the appearance of a single view, thus achieving realistic imm ersion for the majority of wide screen applicati

The principle is that the light intensity in the blend zone from each projector will be adjusted individually, so that the rendering on the screen are perceived as from one projector.

From the start (offset) position, you can blend zone size per edge (left, top, right, bottom). For each edge there will be a drop-off curve for the blend zone.

7.5.1 Blend Zones

About offset and blending width or height

Offset is used to clip the image. T he larger the offset value, the m ore the E.g. Top offset of 100 will blank the top 100 lines.

Height or width is used to create a blending zone with a smooth brightness drop off. This is used to compensate for the double brightness in overlap areas. The value is the size of the blended area in pixels.

image is masked (by black bar) at the co rresponding side.

ons.

How to adjust blend zones?

1. In the main menu, select Installation → Blend.

Image 7-19 Installation menu, Blend

2. In the Blend menu, select Blend Zones.

Image 7-20 Blend menu, Zones

The Blend zones menu is displayed

Image 7-21 Blend Zone menu

3. To enable blending, put the switch to the right. The color of the switch becomes blue when activated.

R5906102 WODAN 15/02/2017

Page 50

7. Advanced operations

4. To show blending lines on the screen, put the switch before Show lines to the right. The color of the switch becomes blue when

activa ted.

5. S pecify the start position (offset)(1) for the blending height and width, setup an siz e value (2) to determine the width of the blending

area.

When the blending lines are activated, you will get a visual indication of the sc reen of the installed blending area.

Image 7-22 1 Start position (offset) 2 B lending width

6. F irst select an offset and click M en u selection to activate the selection.

Use the arrow keys to change the value (the start position of the blending) Repeat for the other edges if necessary.

7. S elect the height or width and se tup a size value.

Repeat for the other edges if necessary. The value will range from 0 to 1.0 (linear to S-curved), with a default value of 0.5.

Example of the use of blending

When projecting an image with 2 projectors, there is always an small overlap that should be corrected by using the blending function.

In order to obtain a satisfying result for th at least 10% of the picture width.

The basic principle is that the overlap setup in the source shall correspond with the blend width setup for the projector. That means that if the overlap zone for the source is set to 500 pixels, the width of the blend zone for the projector also must be set to 500 pixels.

First step is to align the image from the projectors as accurate as possible in a mechanical way, meaning without any optical c orrections. At the same time, establish an overlap in the pictures between the two screens.

Then adjust the remaining irregularities by using the shift and warp features in the projectors to obtain the last ﬁne tuning of the alignment.

Enable blending and activate Show lines.

First set the blending width for th

e right edge of the ﬁrst projector. Enter a width value equal to the overlap area (width1).

Repeat for the left edge o f the second projector.

Adjust the offset to cut the image on each side (masking).

e Blend f unction, the overlap / Blend zone are recommended to be

R5906102 WODAN 15/02/2017

Page 51

Image 7-23 Set up for projector 1

7. Advanced operations

Image 7-24 Set up for projector 2

7.6 Communication

About a network connection

A network c onnection can be made via a wired connection or via the optional wireless unit.

7.6.1 Introduction to a Network connection

DHCP

Dynamic host conﬁguration protocol. DHCP is a communications protocol that lets network administrators manage centrally and automate the assignment of IP addresses in an organization’s network. Using the Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at ea ch computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network.

R5906102 WODAN 15/02/2017 47

Page 52

7. Advanced operations

Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.

Subnet mask

A num ber that is used to identify a subnetwork so that IP addresses can be shared on a local area network.

Default Gateway

A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may need a gateway to connect it to a wide area network (WAN) or to the Internet.

MAC address

Media A ccess Control address. Unique hardware number, used in combination with the IP-address to connect to the network (LAN or WAN).

What should be set up for an Ethernet address?

Two ways can be used to assign an address:

•usetheAutomatic setting so that an automatic address will be assigned.

• Assign manually an IP address, Net-mask (subnet-mask), (default) gateway address.

- Set the IP-Address ﬁeld to the desired value. This must NO T be 0.0.0.0 for static IP-Address assignment. The IP address

identiﬁes a projector’s location on the network in the same way a street address identiﬁes a h a street address must identify a unique residence, an IP address must be globally unique and have a uniform format.

- Set the S ubnet-Mask as appropriate for the local subnet.

- Set the Default-Gateway to the IP-Address of the local router (MUST be on the local subnet!) on the same network as this

projector that is used to forward trafﬁc to destinations beyond the local network. This must not be 0.0.0.0. If there is no router on the projector’s local subnet then just set this ﬁ eld to any IP-Address on the subnet.

ouse on a city block. Just as

7.6.2 Wired IP address set up

How to automatically s et up the IP address

1. In the main menu, select System Settings → Communication.

Image 7-25

2. In the Communication menu, select LAN.

Image 7-26 Communication menu, LAN

48 R5906102 WODAN 15/02/2017

Page 53

The LAN menu is d isplayed

Image 7-27 LAN menu

3. To enable A utomatic, put the switch to the right. The color of the switch becomes blue.

An automatic IP is assigned.

When connected, it is indicated with the connection sy mbol and the indication Connected.

4. Click Apply.

How to manually set up the IP address

1. In the main menu, select System Settings → Communication.

7. Advanced operations

Image 7-28

2. In the Communication menu, select LAN.

Image 7-29 Communication menu, LAN

The LAN menu is d isplayed

Image 7-30 LAN menu

3. Disable Automatic. Put the switch to the left. The switch becomes gray.

4. U se the ▲ or ▼ key to select Address and press OK button to activate the input box.

5. U se the ▲ or ▼ key to change the selected charac ter.

Use the ◄ or ► key to select a nother character.

Note: Digits can be entered with the digit keys on the remote control or the local keypad. W hen a digit is entered in that way,

the next character will be s elected autom atically.

R5906102 WODAN 15/02/2017

Page 54

7. Advanced operations

6. R epeat steps 4 and 5 for the Subnet mask and Default G ateway.

7. Click APPLY to conﬁrm all changes.

When the connection is established, it is indicated with the connection symbol and the indication Connected.

7.7 Service Menu

About the service menu

The service menu can only be entered with a Service code.

Image 7-31 Service code

If you have a service code, select Service code with the arrow keys and click OK to enter the entry mode. Enter the code with the numeric k eys and click OK to conﬁrm. Otherwise click DISCARD to return to the System Settings menu.

Overview

• Service – Color

• Service – Statistics

• Lens Calibration

7.7.1 Service – Color

CAUTION: The native colors h ave been measured and set d

unless parts of the optical path have been replaced due to servicing.

If you need to change the native colors on the device, make sure to also perform a P7 calibration, using the Projector Toolset and a ch rom a meter. For mo re info on P7 calibration, refer to the Projector Toolset R eference guide.

How to adjust the P7 native settings

1. In the main menu, Sy stem Settings → Service.

Image 7-32

2. E nter the service code.

3. In the Service menu, select Color.

uring factory production. Do not change them,

R5906102 WODAN 15/02/2017

Page 55

Image 7-33

The Color m enu will be displayed.

Image 7-34

4. S elect the desired value to change and conﬁrm.

5. Change the values to the desired position, taking into account the color gam ut values.

6. Click Apply.

7. Advanced operations

7.7.2 Service – Statistics

What can be seen?

The statistics s creen show s the general information about the projector.

The following items will be displayed:

• Lamp on runtime

• Lamp Strike

• Projector Runtime

•Systemtime

• Current Uptime

How to display the statistics

1. In the main menu, Sy stem Settings → Service.

Image 7-35

2. E nter the service code.

3. In the Service menu, s elect Statistics.

Image 7-36

R5906102 WODAN 15/02/2017 51

Page 56

7. Advanced operations

The Statistics will be displayed.

Image 7-37

7.7.3 Lens Calibration

Lens calibr ation is a time cons uming operation.

How to calibrate

1. In the main menu, Sy stem Settings → Service.

Image 7-38

2. E nter the service code.

3. In the Service menu, select Lens Calibration.

Image 7-39 System Settings menu — Lens Calibration

The Lens Calibration menu is displayed.

Image 7-40 Lens Calibration menu

4. In the Lens Calibration menu, select the desired calibration action and click OK.

You can select one of the following functions:

52 R5906102 WODAN 15/02/2017

Page 57

7. Advanced operations

- Ho rizontal shift

- Vertical shift

-Focus

- Zoom

- Shutter

- High contrast

The text Calibration in progress will be displayed next to s elected function until the calibration is completed.

When an error is detected, the message Calibration Error is displayed next to function.

7.8 Reset

What can be done?

All s ettings and values on the projector can be reset to its default values. This can be done for one or more settings separately, or all settings together (factory reset).

Default settings

The following settings are default s ettings:

Setting Default value

ImageConnector Color Space

Signal Range

ImageFeatures

ImageWarp

ImageResolution

Optics High Contrast Off

ImageSource Source ﬁles Standard

ImageRealColor

ImageOrientation Orientation

UserInterface

Illumination Power

ImageBlend Blend Width

Contrast

Brightness mid value

Saturation

Screen size 5120x3200 / 2560x1600

4 corner

Output Resolution

P7 Realcolor all set to native

Theme Light

offset

auto

mid value

Warp off, no wa rp

4K UHD

Table, Front

100%

disabled, all value to zero

How to reset one or more projector settings

1. In the main menu, select Sys tem Settings → Reset.

Image 7-41 System Settings menu, Reset

R5906102 WODAN 15/02/2017 53

Page 58

7. Advanced operations

The Reset menu is displayed.

Image 7-42 Reset menu

2. N avigate to the checkbox next to the settings that need to be reset and press OK.

Multiple selection ar e possible.

3. Click RESET to reset all selected settings.

How to reset all projector settings

1. In the main menu, select Sys tem Settings → Reset.

2. In the Reset menu, select RESE T ALL and click OK.

R5906102 WODAN 15/02/2017

Page 59

8. MAINTENANCE

About this chapter

This chapter contains general maintenance procedures.

Overview

• Cleaning the lens

• Cleaning the exterior of the projector

8.1 Cleaning the lens

To minimize the possibility of damage to optical coatings, or scratches to lens surfaces follow the cleaning procedure as described h ere precisely.

Necessary tools

• Compressed air.

• Clean Toraysee® cloth or any micro ﬁber lens cleaning cloth.

• Clean cotton cloth.

8. Maintenance

Necessary parts

Lens cleaner (e.g. Carl Zeiss lens cleaner or Purasol® or any water-based lens cleaner)

How to clean the lens?

1. B low off dust with c lean compr essed air (or pressurized air cans1).

2. Clean with lens cleaner together with a clean lens cleaning cloth to remov e the dust and contamination. Use big wipes in one

single direction.

Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.

3. Use a dry lens cleaning cloth to remove left liquid or stripes. Polish with small circles.

4. If there are still ﬁngerprints on the surface, wipe them off with lens cleaner together with a clean lens cleaning cloth. Polish again

with a dry one.

If smears occur when cleaning lenses, replace the cloth. Smears are the ﬁrstindicationofadirtycloth.

8.2 Cleaning the exterior of the projector

How to cl ean the exterior of the projector ?

1. S witch off the projector and unplug the projector from the mains power n et.

2. Clean the housing o f the projector with a damp cloth. S tubborn stains m ay be removed with a cloth lightly dam pened with a mild

detergent solution.

1. Pressurized air cans are not efficient if there is too much dust on the surface, the pressure is too low

R5906102 WODAN 15/02/2017 55

Page 60

8. Maintenance

56 R5906102 WODAN 15/02/2017

Page 61

9. SPECIFICATIONS

9.1 Dimensions of a Wodan

Overview

725

Center of gravity

373

383

Center of gravity

9. Specifications

413

CG0

CG1

CG2

Image 9-1 Dimensions, mm

Geometrical centre C entre without lens Centre with lens

CG0

CG1

CG2

186.5 170.0 185.0

237.5 241.0 248.0

362.5 370.0 330.0

9.2 Technical Regulations

Certiﬁcates

475

RoHS

Image 9-2 EAC mark

R5906102 WODAN 15/02/2017 57

Image 9-3 Rohs

Image 9-4 Rohs OK

Image 9-5 CE mark

Image 9-6 ETL mark

Page 62

9. Specifications

Image 9-7 CCC mark

Image 9-8 FCC label

Image 9-9 RCM mark

58 R5906102 WODAN 15/02/2017

Page 63

10. Environmental Information

10. E NVIRONMENTAL INFORMATION

Overview

• Disposal information

• China RoHS c ompliance

• Turkey RoHS compliance

• Production address

• Contact information

10.1 Disposal information

Disposal Information

Waste Electrical and Electronic Equipment

This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other m unicipal waste. Please dispose of your waste equipment by handing it over to a designated collection p oint for the recycling o f waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please s eparate these items from other types of waste and recycle t hem responsibly to promote the sustainable reuse of material resources.

For more information about r ecycling of this product, please contact your local city ofﬁce or your municipal waste disposal service.

For details, p lease visit the Barco website at: h

ttp://www.barco.com/en/AboutBarco/weee

Disposal of batteries in t he product

This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately

from municipal waste.

If the battery contains more than the speciﬁed values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol.

By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health.

Disposal of lamp

Dispose of expired bulbs that are beyond w arranty in the following manner: wrap the bulb tightly in several layers of c anvas or heavy cloth. Place it on hard surface and shatter the envelope with a sharp hammer blow. DO NOT place a non shattered bulb in any ordinary refuse container.

Small amounts of radioactive material (< 1000 Bq per lamp) are deliberately added to Xenon lamps for functional reasons. These lamps are manufactured under regulatory control as consumer product according to IAEA basic safety standard BSS 115. Disposal according to national regulations is required e.g. in Europe covered by WEEE regulation. Se e also related user manual of the lamp supplier for more guidance.

10.2 China RoH S compliance

中国大陆 RoHS (Informa tion for China ROHS compliance)

根据中国大陆《电器电子产品有害物质限制使用管理办法》（也称为中国大陆RoHS），以下部分列出了Barco产品中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准：“电子信息产品中有毒物质的限量要求”中。

According to the “Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may c ontain. T he RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirem ents of toxic substances in Electronic Information Products”.

R5906102 WODAN 15/02/2017

Page 64

10. Environmental Information

零件项目( 名称)

Component name

印制电路配件

Printed Circuit Assemblies 外接电(线 )缆

External Cables

內部线路

Internal wiring

光学镜头

Optical lenses 螺帽,螺钉( 栓),螺旋( 钉),垫圈 , 紧固件

Nuts, bolts, screws, washers, Fasteners

电源供应器

Power Supply Unit

风扇

Fan

燈泡支架

Lamp holder

附電池遙控器

Remote control 本表格依据SJ/T 11364的规定编制

This table is prepared in accordance with the provisions of SJ/T 11364.

O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572 标准规定的限量要求以下.

O: Indicates that this toxic or hazardous s ubstance contained in all of the homogene ous materials for this part is below the limit requirement in GB/T 26572.

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 标准规定的限量要求.

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.

在中国大陆销售的相应电子信息产品（EIP ）都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP 标签（请参阅实例，徽标内部的编号使用于指定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。

All E lectronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Marking for the restriction of the use of hazardous substances in electrical and electronic product” of Chinese Mainland, mar ked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland.

有毒有害物质或元素

Hazardous substances and elements

铅

(Pb)

xooo oo

汞

(Hg)

ooooo

镉

(Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

10.3 Turkey RoHS compliance

Turkey RoHS compliance

Türkiye Cumhuriyeti: AEEE Yönetmeliği

[Republic of Turkey: In conformity with the WEEE Regulation]

ne Uygundur.

R5906102 WODAN 15/02/2017

Page 65

10. Environmental Information

10.4 Production address

Factories

Barco NV

Noordlaan 5, B-8520 Kuurne (BELGIUM)

Barco Visual (Beijing) Electronics Co. Ltd.

巴可伟视（北京）电子有限公司

No.16 Changsheng Road, Changping District, 102200, Beijing, P.R.C

北京市昌平区中关村科技园区昌平园昌盛路16号邮政编码：102200

10.5 Contact information

Barco contact information

Registered ofﬁc e address: President Kennedypark 35, 8500 Kortrijk, Belgium

Contact address: Beneluxpark 21, 8500 Kortrijk, Belgium

Importers contact information

To ﬁ nd your local importer, contact B arco directly or one of Barco’s regional ofﬁces via the contact inform ation given on Barco’s web site, w

ww.barco.com.

Made in information

The made in country is indicated on the product ID label on the product itself.

Production date

The month and year of production is indicated on the product ID label on the product itself.

R5906102 WODAN 15/02/2017