Page 1
BARCO PROJECTION SYSTEMS
Date: 13.10.99 Art. No: R5976061
OWNER'S MANUAL
R9827891
VS05
Page 2
Due to constant research, the information in this manual is subject
to change without notice.
Produced by BARCO NV, 1999
All rights reserved.
Trademarks are the rights of their respective owners.
Printed in Belgium
Page 3
R59 76061 VS05 131099 1
Safety instructions.......................................................................................... 3
On installation ................................................................................................ 3
On servicing .................................................................................................. 3
On cleaning ................................................................................................... 3
I. Introduction ................................................................................................... 4
II. Installation of the VS05 .............................................................................. 5
A. Projector - VS05 connections. ................................................................ 5
..... A.1. Data communication connection. ................................................... 5
..... A.2. Signal connection ........................................................................... 7
B. VS05 - audio amplifier connection. .......................................................... 9
C. VS05 - monitor connection. ...................................................................... 9
D. Source connections ............................................................................... 10
..... D.1. Sources to VS05 .......................................................................... 10
..... D.2 Source to projector ........................................................................ 11
III. Operating instructions ............................................................................ 12
A. With the button panel on the VS05. ....................................................... 12
..... A.1. Input selection ............................................................................... 12
..... A.2. Adaptation Keypad to PPM/RC5 Coding ....................................... 12
..... A.3. Analog picture settings : 'Brightness', 'Color', 'Contrast', 'Tint' and .
..... 'Sharpness'................................................................................... 13
..... A.4. Stand-by ....................................................................................... 13
..... A.5. Pause ............................................................................................ 14
..... A.6. TEXT .............................................................................................. 14
B. With the RCU of the projector. ............................................................... 14
..... B.1. Input selection ............................................................................... 14
..... B.2. Analog picture settings : 'Brightness', 'Color', 'Contrast', 'Tint' and .
..... 'Sharpness'.................................................................................... 15
..... B.3. Stand-by ........................................................................................ 16
..... B.4. Pause ............................................................................................ 16
..... B.5. TEXT .............................................................................................. 16
IV. Stand alone use of the VS05. ................................................................ 17
table of contents
Table of Contents
Page 4
R59 76061 VS05 131099 3
safety instructions
Safety instructions
Before operating the set please read this manual thoroughly, and retain it for future
reference.
Record the part number and serial number in the space below. Refer to them
whenever you call upon your BARCO dealer regarding this product.
part number:
serial number:
Warning
To prevent fire or electrical shock hazard, do not expose this VS05 to
rain or moisture.
All instructions for operating and use of this equipment must be
followed precisely.
On installation
Do not place this VS05 on unstable cart, stand or table. The VS05 may fall, causing
serious damage to it.
Do not use this VS05 near water.
On servicing
Replacement parts. When replacement parts are required, be sure the service
technician has used original BARCO replacement part or authorized replacement
parts which have the same characteristics as the BARCO original parts. Unauthorized substitutions may result in degraded performance and reliability, fire, electric
shock or other hazards. Unauthorized substitutions may void warranty.
Safety check. Upon completion of any service or repairs to this VS05, ask the service
technician to perform safety checks to determine that the VS05 is in proper operating
condition.
On cleaning
To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Never
use strong solvents, such as thinner or benzine, or abrasive cleaners since these
will damage the cabinet.
Page 5
R59 76061 VS05 1310994
INTRODUCTION
INTRODUCTION
General
The VS05 is a versatile Video and HDTV source selector for all Barco's digitally
controlled large screen projectors. It offers the possibility to connect and switch up
to 5 Composite Video sources and 3 Super Video sources and 1 RGB analog source.
In addition, the audio signal proper to the source, can be switched to an audio amplifier.
The RGB analog source - directly connected to the projector - can be of standard
or HDTV frequency (in case of HDTV-compatible projectors) or Component Video
(for projectors with Component Video input).
The VS05 fits into any standard 19" rack. Used as stand-alone video source selector
the VS05 can operate with any monitor.
1
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNESS
TINT
COLOR
BRIGHTNESS
CONT RAST
-+
-+
-+
-+
-+
VIDEO SELECTOR VS
05
RGB
COMPONEN T
VIDEO
STANDARD
SYNC
3-LEVEL
SYNC
SYNC ON
GREEN
SEPARATE
SYNC
INPUT SELECTI ON 9
PPM
RC5#0
RC5#1
12
345
6
78
COMM. PORT
AUDIO
VIDEO MON.
OUTPUT
S-VIDEO
AUDIO INPUT
12
3
4
5
6
789
VIDEO INPUT
S-VIDEO IN PU T
Input 9 is connected directly to proj ector
In- Output Terminology
Front view
Rear view
Source 9
mode selection
switches
Display
Keypad
PPM/RC5
mode
selection
Video Inputs
S-Video Inputs
Audio Inputs
(Video)
Audio Inputs
(S-Video)
Audio Input
(RGB or Comp Vid)
Video Out
S-Video Out
Video Out to Monitor
Audio Out
Comm. Port
to Projector
Page 6
R59 76061 VS05 131099 5
installation of the VS05
INSTALLATION OF THE VS05
A. Projector - VS05 connections.
Power down the projector before starting the connections.
A.1. Data communication connection.
Use a D9-D9 link cable to connect the VS05 to the projector.
The cables are available in the following lengths :
5 m (15ft) Order number : 98 27770
15 m (46ft) Order number : 98 27560
30 m (91ft) Order number : 98 27570
High Quality 30 m (91ft) Order number : 9827870
Plug the male D9 connector of the D9-D9 link cable into the female D9 connector
labelled 'COMM PORT' of the VS05.
Plug the female D9 connector of the D9-D9 link cable into the male D9 connector
labelled 'communication Remote-RCVDS' or 'COMM port 800 peripherals' on the rear
panel of the 800, 1100, 1200 or 1600 series projectors or on the front panel of the
700 and 5000 series projectors.
Connection VS05 - BARCO 700 series projector.
2
COMM. PORT
pin description
1 PPM
2 TXD
3 RXD
4 +SBI
5 Ground
6 SCL
7 RDY
8 +30V
9 Ground
COMM PORT
REMOTE
RG(S)B SVIDEO
S-VI DEO
12345 678
COMM. PORT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDIO INPUT
123456
789
VID EO INP UT
S-VIDEO INPUT
Input 9 is conne cted directly to projec to r
Page 7
R59 76061 VS05 1310996
Connection VS05 - BARCO 800, 1100, 1200 or 1600 series projector.
Connection VS05 - BARCO 5000 series projector.
installation of the VS05
12
345
678
COMM . PORT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDI O INPUT
123456789
VIDEO INPUT
S-VIDE O INPUT
Input 9 i s connected directl y to projector
75 ohm
OFF
ON
POR T 1
(VIDEO )
PORT 4/5
(RGB - HV)
Comp /H sy nc
V sync
R
GB
POR T 3
PORT 6 R emote
Comm.
PROJECTOR MODE
POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ON
OFF
GREEN : operati onal
RED : s tand-by
12345678
COMM. PORT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDIO INPUT
12
3
4
5
6
7
89
VIDEO INPUT
S-VIDEO INPUT
Input 9 is connected direc tly to projector
DECODER
VIDEO-INPUT
VIDEO
S-VIDEO
COMPONENT-INPUT
R-YYB-Y
RGB-INPUT
RED GREEN BLUE
H/CsyncVsync
0
I
FOR CONTINUED PROTECTION AGAINST
RISK OF FIRE, REPLACE ONLY WITH
SAME T YPE AND R ATING OF FUSE
RS 232 IN
REMO TE
IR-RECEIVER
F 10 AH / 250 V
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY
COMMUNI CATION PORT
(800 -PERIPHERALS)
100 - 230 V
9 - 4 A
60 - 50 Hz
Page 8
R59 76061 VS05 131099 7
A.2. Signal connection
Connect the video output of the VS05 to the video input of projector using coaxial
cable with BNC connectors.
Connect the S-Video output of the VS05 to the S-Video input of the projector using
a 4-wire coaxial cable with 4 pin connectors.
Signal interconnection VS05 - BARCO 700 series projector.
installation of the VS05
COMM PORT
(800 peri pherals)
REMOTE
RG(S)B SVIDEO
S-VIDEO
12
345
678
COMM. PORT
AUDIO
VIDEO
MON.
OUTPU T
S-VIDEO
AUDIO IN PUT
12
3
4
56789
VIDE O INPUT
S-VIDEO INPUT
Input 9 is connected dir ectly to pr ojector
Page 9
R59 76061 VS05 1310998
Signal interconnection VS05 - BARCO 800, 1100, 1200 and 1600 series
projector.
Signal interconnection VS05 - BARCO 5000 series projector.
installation of the VS05
DECODER
VIDEO-INPUT
VIDEO
S-VIDEO
COMPONENT-INPUT
R-YYB-Y
RGB-INPUT
RED GREEN BLUE
H/CsyncVs yn c
0
I
FOR CONTINUED PROTECTION AGAINST
RISK OF FIRE, REPLACE ONLY WITH
SAME TYPE AND RATING OF FUSE
RS 232 IN
REMOTE
IR-RECEIVER
F 10 AH / 250 V
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY
COMMUNI CATION PORT
(800-PERIPHERALS)
100 - 230 V
9 - 4 A
60 - 50 H z
12345678
COMM. POR T
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDIO INPUT
12
3
4
5
6
7
89
VIDEO INP UT
S-VIDEO INPUT
Input 9 is connected directly to projector
123456
78
COMM. PORT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDIO INPUT
123456789
VIDEO I NPUT
S-VIDEO INPUT
Input 9 is connected directly t o projector
75 ohm
OFF
ON
PORT 1
(VIDEO)
PORT 4/5
(RGB - HV)
Comp /H sy nc
V sync
RGB
PORT 3
PORT 6 Remote
Comm.
PROJECTOR MODE
POWER/MAINS
PORT 2
(S-VIDEO)
75 ohm
ONOFF
GR EEN : op erational
RED : stand-by
Page 10
R59 76061 VS05 131099 9
Connect the left and right audio outputs of the VS05 to the left and right audio inputs
of an audio amplifier using two conductor audio cables with RCA (cinch) connectors.
B. VS05 - audio amplifier connection.
C. VS05 - monitor connection.
When connecting a monitor, using a coaxial cable with BNC terminals, to the VS05
monitor output, it is possible to view the selected source (video or S-video) on the
monitor screen in video (S-video will be converted into video). (only for input
selections 1 to 8)
installation of the VS05
12
345
678
COMM. PORT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDI O INPUT
123
4
5
6
789
VIDEO INPUT
S-VIDEO INPUT
Input 9 is connec ted directly t o project or
1
2
3456
78
COMM. PO RT
AUDIO
VIDEO
MON.
OUTPUT
S-VI DEO
AUDIO I NPUT
12
3
4
5
6
7
89
VIDEO INPUT
S-VIDE O INPUT
Input 9 is connected directly to projector
Page 11
R59 76061 VS05 13109910
D. Source connections
installation of the VS05
TV tuner, e.g. TVDM40 stereo
VCR
VCR S-VHS
VCR S-VHS
1
2
345 678
COMM. PORT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDIO INPUT
12
3
4
5
6
789
VIDEO INPUT
S-VIDEO INPUT
Input 9 is connected directl y to projector
D.1. Sources to VS05
D.1.a. Video + audio
Connect the video sources to the video inputs of the VS05 (inputs 1 to 5) using
coaxial cables with BNC connectors. Connect the audio sources, corresponding
with the Video sources, to the audio inputs of the VS05 using two conductor audio
cables with RCA (cinch) connectors.
D.1.b. S-Video + audio
Connect the S-Video sources to the S-Video inputs of the VS05 (inputs 6 to 8)
using 4-wire coaxial cables with 4 pins connectors. Connect the audio sources,
corresponding with the S-Video sources, to the audio inputs of the VS05 using
two conductor audio cables with RCA (cinch) connectors.
Page 12
R59 76061 VS05 131099 11
installation of the VS05
D.2 Source to projector
One RGB analog source (standard or HDTV frequency - in case of HDTV compatible
projectors -) or Component Video source (for projectors with Component Video
input) with audio signal can be switched by the VS05 (source 9).
D.2.a. RGB analog source + audio
Connect the RGB analog source directly to the RGB analog input of projector using
coaxial cables with BNC connectors. Connect the corresponding audio signals to
audio input 9 of the VS05 using two conductor audio cables with RCA (cinch)
connectors.
D.2.b.Component Video source + audio
Connect the Component Video source directly to the RGB analog input of projector
(for projectors with component video input) or to the Component inputs (5000 series)
using coaxial cables with BNC connectors. Connect the corresponding audio signals
to audio input 9 of the VS05 using two conductor audio cables with RCA (cinch)
connectors.
Page 13
R59 76061 VS05 13109912
operating instructions
3
OPERATING INSTRUCTIONS
A. With the Keypad on the VS05.
The VS05 is linked with the projector via a bi-directional data communication line. All
actions entered by touching a button on the front panel are decoded by the projector
in control or switch functions for the projector or the VS05.
The controls on the button panel of the VS05 have the same functions as those on
the RCU:
- input selection
- analog picture settings
- stand-by switching
- text on/off
- pause function
A.1 Adaptation Keypad to PPM or RC5 coding
The switch PPM/RC5 on the front panel allows
to adapt the transmission code of the local
keypad towards PPM or RC5#0 similar the transmission code of the connected projector (Position RC5#1 is provided for further expansion).
A.2 Input selection
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNE SS
TINT
COLOR
BRIGHTNESS
CONTRAST
-+
-+
-+
-+
-+
VS
05
PPM
RC5#0
RC5#1
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNE SS
TINT
COLOR
BRIGHTNESS
CONTRAST
-+
-+
-+
-+
-+
VS
05
PPM
RC5#0
RC5#1
numeric keypad
Input input selection source type
1 1 Composite Video
2 2 Composite Video
3 3 Composite Video
4 4 Composite Video
5 5 Composite Video
6 6 S-Video
7 7 S-Video
8 8 S-Video
9* 9 RGB or ponent Video
* Key in a source number with the numeric keys
(number between 1 and 9).
* When the source is available :
- source is displayed on the screen.
- source number is displayed on the display.
- the corresponding audio input is switched
through to the amplifier.
Switch PPM/RC5
* Source is directly connected to the RGB terminals of the projector (800, 1100, 1200,
1600,5000 series) or to the Component input (5000 series) (see Source to projector
connection).
Page 14
R59 76061 VS05 131099 13
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
-+
-+
-+
-+
-+
VS
05
PPM
RC5#0
RC5#1
RGB
COMPONEN T
VIDEO
STANDARD
SYNC
3-LEVEL
SYNC
SYNC ON
GREEN
SEPARATE
SYNC
INPUT SELECTI ON 9
Note for source selection 9 : Set the switches on the front panel of the VS05 in their
correct position before selecting source 9.
The following indications have to
be set before a correct operation is
possible.
Source type : RGB analog or Component Video.
Sync type : standard sync or 3level sync.
Sync position : sync on green or
separate sync.
A.3 Analog picture settings :
'Brightness', 'Color', 'Contrast', 'Tint' and 'Sharpness'.
* Press the + and - key to change the analog
picture settings.
Note :
When TEXT is ON :
* A bar scale and a number below this bar scale
(between 0 and 99) appear on the screen every
time when touching a + or - key.
When TEXT is OFF :
* No indication of the change on the screen.
A.4 Stand-by
To go to stand-by : press once on the stand-by
button.
Return out of stand-by :
a. press stand-by key : last selected source will
be displayed.
or
b. press a source number : the selected source
will be displayed.
Note for 5000 series projectors :
When stand-by key is pressed, the projector asks for a confirmation. Press standby key a second time to switch to stand-by. If you want to cancel, select CANCEL
with the arrow keys on the RCU and press ENTER on that RCU.
operating instructions
Sync position
Sync type
Source type
SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
-
+
-
+
-
+
-
+
-
+
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNE SS
TINT
COLOR
BRIGHTNESS
CONTRAST
-+
-+
-+
-+
-+
VS
05
PPM
RC5#0
RC5#1
ê
Page 15
R59 76061 VS05 13109914
operating instructions
A.5 Pause
B. With the RCU of the projector.
With the RCU, it is possible to control the projector and the VS05. Point the IR beam
to the reflective screen surface or to one of the IR inputs of the projector.
B.1. Input selection
BRIG HTNESS
-
+
-
+
-
+
-
+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
0
9
7
8
6
5
4
3
2
1
* Press Pause to interrupt the image projection.
Projector stays with full power for
immediate restarting.
* Restart :
- Press Pause again. The image will be
redisplayed.
or
- enter a source number.
A.6 TEXT
This button acts as a toggle switch in
operational mode between text ON and
text OFF. When text is ON, a bar scale and
number indication will be displayed during
a change of an image control. When text
is off, no indication will be displayed on the
screen when changing an image control.
* Key in a source number with the numeric keys
(number between 1 and 9).
* When the source is available :
- source is displayed on the screen.
- source number is displayed on the display.
- the corresponding audio input is switched
through to the amplifier.
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
-+
-+
-+
-+
-+
VS
05
PPM
RC5#0
RC5#1
ê
0
321
456
789
STANDBY
PAUSE
TEXT SHARPNESS
TINT
COLOR
BRIGHTNESS
CONTRAST
-+
-+
-+
-+
-+
VS
05
PPM
RC5#0
RC5#1
ê
Page 16
R59 76061 VS05 131099 15
Input input selection source type
1 1 Composite Video
2 2 Composite Video
3 3 Composite Video
4 4 Composite Video
5 5 Composite Video
6 6 S-Video
7 7 S-Video
8 8 S-Video
9* 9 RGB or Component Video
* Source is directly connected to the RGB terminals of the projector (800,
1100, 1200, 1600,5000 series) or to the Component input (5000 series) (see
Source to VS05 connection).
Note for source selection 9 : Set the switches on the front panel of the VS05
in their correct position before selecting source 9.
The following indications
have to be set before a
correct operation is possible.
Source type : RGB analog or Component Video.
Sync type : standard sync
or 3-level sync.
sync position : sync on
green or separate sync.
B.2. Analog picture settings :
'Brightness', 'Color', 'Contrast', 'Tint' and 'Sharpness'.
* Press the + and - key to change the analog picture
settings.
Note :
When TEXT is ON :
* A bar scale and a number below this bar scale
(between 0 and 100) appear on the screen every time
when touching a + or - key.
When TEXT is OFF :
* No indication of the change on the screen.
operating instructions
BRIGHTNESS
-
+
-
+
-
+
-
+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
0
9
7
8
6
5
4
3
2
1
RGB
COMPONEN T
VIDEO
STANDARD
SYNC
3-LEVEL
SYNC
SYNC ON
GREEN
SEPARATE
SYNC
INPUT SELECTI ON 9
Sync position
Sync type
Source type
Page 17
R59 76061 VS05 13109916
operating instructions
ADDR
ADJ
EXIT
ST BY TE XT
FREEZ
ENT ER
PAUSE
ADDR
ADJ
EXIT
ST BY TE XT
FREEZ
ENT ER
PAUSE
ADDR
ADJ
EXIT
ST BY TEXT
FREEZ
ENT ER
PAUSE
B.3. Stand-by
To go to stand-by : press once on the stand by
button.
Return out of stand-by :
a. press stand-by key : last selected source will
be displayed.
or
b. press a source number : the selected source
will be displayed.
B.4. Pause
* Press Pause to interrupt the image projection.
Projector stays with full power for immediate
restarting.
* Restart :
- Press Pause again. The image will be redisplayed.
or
- enter a source number.
B.5. TEXT
This button acts as a toggle switch in
operational mode between text ON and text
OFF. When text is ON, a bar scale and
number indication will be displayed during
a change of an image control. When text is
off, no indication will be displayed on the
screen when changing an image control.
ê
ê
ê
Page 18
R59 76061 VS05 131099 17
STAND ALONE USE OF THE VS05
STAND ALONE USE OF THE VS05.
If supplied with an external DC voltage (between 15 and 20V/200mA), the VS05 can
switch the input source to projector or monitor. The analog picture controls on the
key pad of the VS05 are enabled.
Basic configuration.
Supply a DC voltage (15 - 20V/200mA) to pin 6 of the D-sub-9 connector labelled
'comm port'. Pin 5 and 9 are ground.
4
TV tuner, e.g. TVDM 40 stereo
VCR
VCR S-VHS
VCR S-VHS
To projector
or monitor
DC power
supply
1
2
345678
COMM. PO RT
AUDIO
VIDEO
MON.
OUTPUT
S-VIDEO
AUDIO INPUT
12
3
4
5
6
7
89
VIDEO INPUT
S-VIDEO INPUT
Input 9 is connected directl y to projector
Connect your sources to the VS05 as described in Source connection to VS05.
5 video inputs and 3 S-Video inputs can be switched through to the outputs of the
VS05. The selection has to be done with the numeric keys on the button panel of
the VS05 (source 1 to 8, no source 9 -direct connection to the projector - available).
Page 19
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium
Loading...