Barco SLM R10 Performer User Manual

BarcoR10 SLM

Owners Manual

R9010010

R5976563/03 20/10/2004

Barco nv Events

aan 5, B-8520 Kuurne

Noordl Phone: +32 56.36.89.70 Fax: +32 56.36.88.24

events@barco.com

E-mail: Visit us at the web: www.barco.com

PrintedinBelgium

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC r These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of t cause harmful interference, in which case the user will be responsible for correcting any interference.

his equipment in a residential area may

ules.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures.

1. Safety Instructions

1. SAFETY INSTRUCTIONS

1.1 Warnings

To prevent personnel injury

The customer should never attempt to disassemble the lamp casing or to dispose of the lamp casing other than by returning it to BARCO.

To prevent injuries and physical damage, always read this manual and all labels on the system before connecting to the or adjusting the projector.

To prevent injuries, take note of the weight of the projector. Minimum 4 persons are needed to carry the projector.

NEVER look into the lens ! Due to the high luminance damage to the eye can happen.

Before attempting to remove the projector’s cover, you must turn off the projector and disconnect from the wall outlet.

When performing set up work at a ceiling mounted projector, to prevent injury caused by falling obje out area.

Consult a professional structural engineer prior to suspending the ceiling mount from a structure not intended for that use. Always ensure the working load limit of the structure supporting the projector.

The power input at the projector side is considered as the disconnect device. When me some parts inside, always disconnect the power cord at the projector side.

ntioned to switch of the projector, to access

cts or the system, set out a keep

wall outlet,

To prevent projector damage

If the Air Filters are not regularly replaced, the air flow inside the projector could be disrupted, causing overheating. Overheating may lead to the projector shutting down during operation.

In order to ensure that correct airflow is maintained, and that the proj it should always be operated with all of it’s covers in place.

Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do not operate the projector again until it has been checked by qualified service personnel.

The projector must always be mounted in a manner which ensures free flo hot air exhausted from its cooling system. Heat sensitive materials should not be placed in the path of the exhausted air.

Special care should be used when DLP projectors are used in the same room as performant laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices (TM) in which case there is a loss of warranty

ector complies with Electromagnetic Compatibility requirements,

w of air into its air inlets and unimpeded evacuation of the

To prevent battery explosion

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

1.2 FCC statement

Federal Communication Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference.

1.3 Note

Definitions

Definition Qualified service technicians or Qualified technicians : Persons having appropriate technical training and experience necessary to be aware of hazards to which they are exposed in performing a task and of measures to minimize the danger to themselves or other persons.

R5976563 BARCOR10 SLM 20/10/2004 1

1. Safety Instructions

Extra Safety manual

Read also safety instructions in separate manual (R5976125).

R5976563 BARCOR10 SLM 20/10/2004

2. Packaging and Dimensions

2. PACKAGING AND DIMENSIONS

Overview

• Projector Packaging

• Box Content

• Lamp Packaging

• Lens Packaging

• Projector Case

2.1 Projector Packaging

Way of Packaging

The projector is packed in a carton box. To provide protection during transportation, the projector is surrounded with foam. The package is secured with banding and fastening clips.

To unpack

1. Release the fastening clips.

2. Remove the banding. Handle as shown in the drawing. (image 2-1)

3. Take the projector out of its shipping carton and place it on a table.

PULL

TO OPE

Image 2-1

Save the original shipping carton and packing material, they will be necessary if you ever have to ship your projector. For maximum protection, repack your projector as i

CAUTION: Never transport the projector with the lens mounted on it !

Always remove the lens before transporting the projector.

2.2 Box Content

Content

• 1 projector BARCO SLM R10 (weight ± 56 kg or 123.5 lbs)

• 1 remote control unit RCU + 1 battery.

• 1 European and 1 American power cable.

• 1 Terminator for linked CLO

• 1 owners manual

• 1 safety manual

t was originally packed at the factory.

R5976563 BARCOR10 SLM 20/10/2004

2. Packaging and Dimensions

2.3 Lamp Packaging

Way of packaging

As it is not allowed to transport the projector with the lamp mounted inside the projector, this lamp is packed in a separate carton box.

Save this carton box , it can be used to repack the lamp when you ever have to transport your projector.

2.4 Lens Packaging

Way of Packaging

Lenses are supplied as an individual item.

They are packed in a carton.

2.5 Projector Case

Dimensions

The dimensions are given in mm

25.4mm = 1 inch

372,7

466

0 456

64,5 520,5

Image 2-2 Front view dimensions

FRONT VIEW

IR-receiver

AIR IN

83 373

38 418

AIR OUT

118

64,5

162

4 R5976563 BARCOR10 SLM 20/10/2004

Image 2-3 Side view dimensions

2. Packaging and Dimensions

R5976563 BARCOR10 SLM 20/10/2004 5

2. Packaging and Dimensions

6 R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

3. INSTALLATION GUIDELINES

The engines are non sealed versions.

3.1 General

WARNING: Before installing the projector, read first the safety instructions.

Ambient Temperature Conditions.

Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.

Max. ambient temperature : 35°C or 95 °F

Min. ambient temperature : 10 °C or 50 °F

The projector will not operate if ambient air temperature falls outside this range (10°C- 35°C or 50°F-95°F).

Storage temperature: -35°C to +65°C (-31°F to 149°F)

Humidity Conditions

Storage: 0 to 98 % RH Non-condensing

Operation: 0 to 95 % RH Non-condensing

CAUTION: Harmful Environmental Contamination Precaution

Environment

Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive.

Environment condition check

A projector must always be mounted in a manner which ensure installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirab air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered.

Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning optical parts, never use industrial strength cleaners on the projector’s optics as these will degrade optical coatings and damage sensitive optoelectronics components. Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contaminants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be non-effective and impracticable. Damage of this nature is under no circumstances covered under the manufacturer’s warranty and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the environment of the projector. The manufacturer reserves the right to refuse repair if a projector has been subject to wantful neglect, abandon or improper use.

le to have this contamination removed prior to it reaching the projectors clean

s the free flow of clean air into the projectors ventilation inlets. For

Special Care for Laser Beams

Special care should be used when DLP projectors are used in the same room as performant laser equipment. Direct or indirect hitting of a laser beam on to the lens can seve

rely damage the Digital MicroMirror Devices™ in which case there is a loss of warranty

Which screen type ?

There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications.

R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a gain of 10 (x10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another consideration called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For more information about screens, contact your local screen supplier.

What image size? How big should the image be?

The projector is designed for projecting an image size : min 1.00m (3.3ft) to max 15 m (49.2ft) (depending on the ambient light conditions), with an aspect ratio of 4 to 3.

3.2 Configuration

Which configuration can be used?

The projector can be installed to project images in four different configurations:

• Front/table

• Rear/table

• Front/ceiling

• Rear/ceiling

Positioning the projector

Table mounted, front projection

Table/Top side facing ceiling

Projector

CD = SH/2 + B - A

SIDE VIEW

Optical axis projection lens

Floor

TOP VIEW

Screen

Floor

BACK VIEW

Image 3-1 Table mounted configuration

8 R5976563 BARCOR10 SLM 20/10/2004

Table mounted, front projection, second way.

Table/Top side facing floor

Projector

SIDE VIEW

Optical axis projection lens

Screen

3. Installation Guidelines

CD = SH/2 + B + A - 554mm

Image 3-2 Table mounted configuration up side do wn

Ceiling mounted, front projection

Ceiling/Top side facing floor

Floor

Screen

TOP VIEW

Floor

BACK VIEW

Ceiling

Projector

Image 3-3 Ceiling mounted projector

CD = SH/2 + B - A

Optical axis projection lens

SIDE VIEW

CEILING VIEW

Ceiling

BACK VIEW

Screen

R5976563 BARCOR10 SLM 20/10/2004 9

3. Installation Guidelines

Ceiling mounted, front projection, second way.

Ceiling/Top side facing ceiling

Ceiling

Projector

Image 3-4 Ceiling mounted projector

CD = SH/2 + B + A - 554mm

Ceiling

Optical axis projection lens

SIDE VIEW

CEILING VIEW

BACK VIEW

Screen

3.3 Safety Area around projector

Safety area

Make sure the projector is located so that the air inlets and outlets for the cooling system are not obstructed. Leave a safety area A of about 1 meter on the left and the right side of the projector.

R5976563 BARCOR10 SLM 20/10/2004

Image 3-5 Safety a rea around the projector

3. Installation Guidelines

R5976563 BARCOR10 SLM 20/10/2004 11

3. Installation Guidelines

3.4 Projector tilting

Turning around the projection axes

(E) FRONT VIEW

15° 15°

(D)Lamp

Axis

Image 3-6 Tilting diagram

A Allowed Projector Tilting Area B Forbidden Projector Tilting Area C Start point D Lamp axis EFrontview

Consider the starting point at the lamp side (input side), the following tilting is possible :

• Maximum 15° upwards

• Maximum 195° downwards (indicated by the allowed projector tilting area)

Forwards and backwards tilting

Forwards and backwards tiltin

g is allowed.

3.5 Mounting the projection lamp

WARNING: Unplug the power cord from the wall outlet before starting with the mounting procedure.

WARNING: Mounting the projection lamp should be done by qualified service technician.

12 R5976563 BARCOR10 SLM 20/10/2004

3.5.1 Access to the Lamp Unit.

What has to be done

To access the lamp casing, a side panel has to be removed.

Necessary tools

A flatblade screwdriver of 5 mm

Removingthesidepanel

1. Turn with a screwdriver the side panel lock screw a quarter turn counter clockwise. (image 3-7)

2. Pull the right side of the panel towards you and further to the right to remove. (image 3-8)

3. Installation Guidelines

Image 3-7 Unlocking the side cover

Image 3-8 Pull and remove the side cover

3.5.2 Installation of the new Lamp Unit.

What has to be done

First remove the lock nut on each spacer screw and next slide the lamp unit into the projector frame.

R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

Necessary tools

Flatblade screwdriver of 5mm or Nut driver 8mm

Installing the lamp unit

1. Remove the lock nut on the 3 spacer screws (A). (image 3-9)

2. Line up the lamp unit guides with the guides on the projector frame (B) and push the unit into the frame until it fits. (image 3-10)

3. Secure the position of the lamp unit with the 3 spacer screws. (image 3-11)

Image 3-9 Lamp unit, rem oving the lock nuts

14 R5976563 BARCOR10 SLM 20/10/2004

Image 3-10 Inserting the lamp

3. Installation Guidelines

Image 3-11 Securing the lamp

3.5.3 Reinstalling the Side Panel

What has to be done

After the new lamp unit has been installed, the side panel has to be remounted.

Necessary tools

A flatblade screwdriver of 5 mm

Reinstalling the side panel

1. Move the cover guides under the back cover and push the front of the cover against the projector frame lining up the cover lock screw with the speed nut (A) on the frame. (image 3-12, image 3-13)

2. Turn with a screwdriver the side panel lock screw (B) a quarter turn clockwise to lock. (image 3-14)

R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

Image 3-12 Mounting the side cover

Image 3-13 Closing the side cover

Image 3-14 Lockingthesidecover

3.6 Re-adjusting the lamp position in the lamp casing

WARNING: As the projector has to be opened, this procedure has to be performed by qualified service tech-

nician.

Why

With higher run times, the light output of the lamp will decrease, which results in a lower light output on the screen. This light output decrease can be compensated by readjusting the position of the lamp.

A suggestion dialog box will be displayed when the projector is restarted after 100 hours and 250 hours. Once ENTER is pressed when that box is open, this box will not be displayed again till the next alert point is reached.

R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

Suggestion

Lamp runtime is

105 hours

It is advisable to

adjust the Z-axis

of the lamp to obtain maximum

light output

(see owners manual)

<ENTER> to confirm

Menu 3-1

The user can now adjust the Z-axis by following the next procedure.

How to readjust.

1. On the side of the inputs, turn the retaining bolt a quarter counter clockwise.

2. Flip the cover to the left side and take off. (image 3-15)

3. Start up the adjustment mode and select Service. (menu 3-2)

4. Select Lamp. The Z-axis indication (lamp menu in service mode) will be helpful while turning screw B . (menu 3-3)

5. Loosen the nut A (image 3-16)on the back of the lamp casing (nutdriver 10).

6. Adjust the screw B (image 3-16)with an Allen key by turning a little clockwise until the maximum light output is reached (the maximum value of the Z-AXIS indication on the lamp menu).

7. Fasten the nut on the back of the lamp casing to secure this position (nutdriver 10).

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Select with ↑ or ↓

then <ENTER>

<EXIT> to return

Menu 3-2

Image 3-15 Lamp adjustment access

CHANGE PASSWORD

CHANGE LANGUAGE CHANGE PROJ. ADDRESS SERIAL COMMUNICATION

Select with ↑ or ↓

<EXIT> to return

Menu 3-3

SERVICE

IDENTIFICATION

NETWORK

LAMP

DIMMING MORE...

then <ENTER>

LAMP

Constant Light output [OFF]

Using [RS port]

Mode [NORMAL]

Serial number : R101111

Article number : R9840xxx

Run time : 10 hours

Remaining run time : 490

hours

Number of strikes : 10

Z_AXIS : 100

Select with ↑ or ↓

then <ENTER>

<EXIT> to return.

Menu 3-4

R5976563 BARCOR10 SLM 20/10/2004 17

3. Installation Guidelines

Image 3-16

3.7Le

nses

verview

• Lenses

• Lens selection

• Lens formulas

• Lens Installation

• Clean

ing the lens

3.7.1 Lenses

Available lenses

TLD(1.6–2.0:1)

TLD(2.0–2.8:1)

8–5.0:1)

TLD(2.

CAUTION: Never turn the other screws ! These are factory aligned.

0670

R984

R9840680

R9840690

TLD(1.2:1)

TLD(0.8:1)

TLD(5.0–

TLD HB(0.8:1)

TLD HB(1.6–2.0:1)

18 R5976563 BARCOR10 SLM 20/10/2004

8.0:1)

R984077

R9840900

R9840910

R9842040

R9842060

3. Installation Guidelines

TLD HB(2.0–2.8:1)

TLD HB(2.8–5.0:1)

TLD HB(5.0–8.0:1)

R9842080

R9842100

R9842120

3.7.2 Lens selection

How to select ?

1. Determine the required screen width.

2. Determine the approximate position of the projector in the projection room with regard to the screen and measure the projectorscreen distance (PD).

3. Use the lens formulas to find the best corresponding PD with regard to the measured projector-screen distance for the required screen width.

3.7.3 Lens formulas

Formulas

Metric formulas (meter) Inch formulas (inch)

TLD(0.8:1) PD=0.85xSW-0.05 PD=0.85SW-1.97

TLD(1.2:1) PD=1.22xSW-0.01 PD=1.22xSW-0.39

TLD(1.6–2.0:1) PD

TLD(2.0–2.8:1) PD

=1.62xSW-0.09

min

=2.03xSW-0.13

max

=2.03xSW-0.17

min

=2.88xSW-0.24

max

=1.62xSW-3.54

min

=2.03xSW-5.12

max

=2.03xSW-6.69

min

=2.88xSW-9.45

max

TLD(2.8–5.0:1) PD

TLD(5.0–8.0:1) PD

=2.84xSW-0.16

min

=5.18xSW-0.38

max

=4.97xSW-0.01

min

=8.28xSW-0.29

max

=2.84xSW-6.30

min

=5.18xSW-14.96

max

=4.97xSW-0.39

min

=8.28xSW-11.42

max

TLD HB(0.8:1) PD=0.85xSW-0.05 PD=0.85SW-1.97

TLD HB(1.2:1) PD=1.22xSW-0.01 PD=1.22xSW-0.39

TLD HB(1.6–2.0:1) PD

TLD HB(2.0–2.8:1) PD

TLD HB(2.8–5.0:1) PD

TLD HB(5.0–8.0:1) PD

=1.62xSW-0.09

min

=2.03xSW-0.13

max

=2.03xSW-0.17

min

=2.88xSW-0.24

max

=2.84xSW-0.16

min

=5.18xSW-0.38

max

=4.97xSW-0.01

min

=8.28xSW-0.29

max

=1.62xSW-3.54

min

=2.03xSW-5.12

max

=2.03xSW-6.69

min

=2.88xSW-9.45

max

=2.84xSW-6.30

min

=5.18xSW-14.96

max

=4.97xSW-0.39

min

=8.28xSW-11.42

max

R5976563 BARCOR10 SLM 20/10/2004 19

3. Installation Guidelines

3.7.4 Lens Installation

How to install ?

Follow the next procedure:

1. Remove the foam rubber in the opening of the lens holder.

2. Take the lens assembly out of its packing material and remove the lens caps on both sides.

3. Move the handle (A) of the lens anchor system to the right. (image 3-17)

4. Push the lens, motors at the top, in the lens block gap horizontally, lining up the motor connector on the lens with the connector on the lens block (B), until the lens clicks in the lens anchor system. (image 3-18)

Caution: On a table mounted projector, hold the projector when pushing the lens into the lens block to avoid sliding off from

the table.

Image 3-18 Mounted Lens

Image 3-17 Lens installation

3.7.5 Cleaning the lens

To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have developed recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.

Necessary tools

To ra ys e eTMcloth (delivered together with the lens kit). Order number : R379058.

Howtocleanthelens?

Proceed as follow :

1. Always wipe lenses with a CLEAN Toraysee

2. Always wipe lenses in a single direction.

Warning: Do not wip

3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

e back and forwards across the lens surface as this tends to grind dirt into the coating.

cloth.

WARNING: Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the

cloth.

Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

CAUTION: Other lenses can also be cleaned safely with this Toraysee

20 R5976563 BARCOR10 SLM 20/10/2004

cloth.

3. Installation Guidelines

3.8 Battery Installation in the RCU

How is the battery delivered ?

A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord.

How to install ?

1. Remove the battery cover on the backside of the remote control by pushing the indicated handle a little towards the bottom of the RCU. (image 3-19)

2. Lift up the top side of the cover at the same time.image 3-19

3. Insert the new 9 V battery (type E-block or equivalent) in the lower compartment.

4. Connect the battery (B) to the contact plate (A). (image 3-20)

5. Insert the battery into the lower compartment and put the cover back.

6. Insert a overview card (C) in the back side.image 3-20

Image 3-19 Opening the battery cover of the RCU

Image 3-20 Mounting the battery into the RCU

3.9 Stacking Projectors

What is possible?

Up to 3 projectors can be stacked on each other without using extra tools or accessories.

How to stack?

Handle as follow:

1. Put the second projector on the first one so that base plate of the second projector matches with the rigging socket of the first projector. (image 3-21)

2. Turn the rigging sockets of the second projector counter clockwise until they are free to move up and down. (image 3-22)

cure the projectors on each other by bringing the free part of the second projector into the socket of the first projector and turn

3. Se a quarter clockwise while pushing downwards until it clicks in.

4. For ceiling mounted configurations, pull on the hook (A) with the cable of the lowest projector. (image 3-23)

5. Guide hook and cable around the carry handle and guide it around the carry handle of the upper projector. (image 3-24)

6. Hook it in the foreseen hole B in the base plate of the upper projector. (image 3-25)

R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

Image 3-21 Stacking two projectors

Image 3-22 Closing the rigging sockets

Image 3-23 Mounting the security chain

Image 3-24 Mounting the security hook

22 R5976563 BARCOR10 SLM 20/10/2004

3. Installation Guidelines

Image 3-25 Mounting the security hook (detail)

How to open a secured rigging point?

1. Push the ring (A) of the first projector downwards and hold it in that position. (image 3-26)

2. Turn the locked part (B) of the second projector a quarter counter clockwise and move it upwards.

Image 3-26 Opening the rigging sockets

R5976563 BARCOR10 SLM 20/10/2004 23

3. Installation Guidelines

3.10 Rigging points and Accessories

Clamps

Slots are made in the carry handle frame for easy inserting the overlockers and for easy adjusting the clamps position so that this position matches with the rigging points.

Image 3-28 Image 3-27 Mounting the clamps

Mounting the clamps

WARNING: When mounting the projector to the ceiling or to a rigging system, always mount security chains.

How to mount the clamps?

To fix the clamps to the U-profile, follow the next procedure :

1. Measure the distance, center tube as reference, between the two used support bars of a truss.

2. Slide the clamps holders (2 per profile) on its place in the U-profile according the measured distance and secure this position. (image 3-29)

3. Turn the o

The overlocker can turn around.

verlockers in the holes of the clamp holder.

Image 3-29 Mounting the clamp — detail

24 R5976563 BARCOR10 SLM 20/10/2004

How to mount the Overlockers to the truss?

To mount the overlocker to the truss, handle as follow :

1. Open the fixation handle. (image 3-30)

2. Hook the clamp around the tube.

The trigger automatically shuts the clamp.

3. Close the fixation handle and secure it by turning the hand screw. (image 3-31)

3. Installation Guidelines

Image 3-30 Opening the rigging clamp

Image 3-31 Closing the rigging clamp

R5976563 BARCOR10 SLM 20/10/2004 25

3. Installation Guidelines

26 R5976563 BARCOR10 SLM 20/10/2004

+ 107 hidden pages