Barco MXRT-5550, MXRT-5600, MXRT-5500, MXRT-5450, MXRT-45002 User Manual
...
Display Contr oller
User Guide
Windows 7, Windows 8.1 and Windows 10
K5905271/11
27/02/2017
Barco NV
neluxpark 21, 8500 Kortrijk, Belgium
Be
Phone: +32 56.23.32.11
Fax: +32 56.26.22.62
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Registered address: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: +32 56.23.32.11
Fax: +32 56.26.22.62
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
PrintedinBelgium
Table of contents
TABLE O F CONTENTS
1. Welcome! .............................................. ............................................ 3
1.1 About the product ............................................................................................. 3
1.2 What’s in the box.............................................................................................. 3
2. Display Controller installation ..... ........................................................... 5
2.1 Which Display Controller ?.. ................ ................ ................ ................ ................ . 5
2.2 Installing a Barco Display Controller ........................................................................ 5
2.3 Installation procedure...................... ................ ................ ................ ................ ... 6
2.4 Connecting your Barco Displays ............... ................ ................ ................ ............. 7
2.5 Dongles ........................................................................................................ 9
2.5.1 Passive Single-Link Dongle ............................................................................ 9
2.5.2 Active Single-Link Dongle ..............................................................................10
2.5.3 Active Dual-Link Dongle ................................................................................10
2.6 Shipping the Barco Display Controller. ................ ................ ................ ................ .....10
3. Driver and software installation .......................... .................................... 13
3.1 Introduction ........... ................ ................ ................ ................ ................ .........13
3.2 Installation procedure...................... ................ ................ ................ ................ ...14
3.3 Silent installation ................... ................ ................ ................ ................ ...........14
3.4 Installation options ............................................................................................15
3.5 After installation ...............................................................................................15
3.6 Uninstallation ... ................ ................ ................ ................ ................ ............... 16
4. Configuring Barco displays in Windows ....... ............................................ 19
4.1 Display resolution ............ ................ ................ ................ ................ ................ .19
4.2 Software rotation ............... ................ ................ ................ .................. .............19
5. Driver and software features ............................................................ ...... 21
5.1 Barco System Settings Control Panel ... ................ ................ ................ ................ ...21
5.1.1 Description ...... ................ ................ ................ ................ ................ .........21
5.1.2 Operation.................... ................ ................ ................ ................ .............21
5.2 Application Appearance Manager ...........................................................................22
5.2.1 Description ...... ................ ................ ................ ................ ................ .........22
5.2.2 Operation.................... ................ ................ ................ ................ .............23
5.2.3 Configuration.............................................................................................23
5.3 Conference CloneView ................ ................ ................ ................ ................ .......23
5.3.1 Description ...... ................ ................ ................ ................ ................ .........23
5.3.2 Operation.................... ................ ................ ................ ................ .............24
5.3.3 Configuration.............................................................................................25
5.4 DimView........................................................................................................25
5.4.1 Description ...... ................ ................ ................ ................ ................ .........25
5.4.2 Operation.................... ................ ................ ................ ................ .............25
5.4.3 Configuration.............................................................................................25
5.5 Film Clip..... ................ ................ ................ ................ ................ .................. .26
5.5.1 Description ...... ................ ................ ................ ................ ................ .........26
5.5.2 Operation.................... ................ ................ ................ ................ .............26
5.5.3 Configuration.............................................................................................26
5.6 FindCursor.....................................................................................................26
5.6.1 Description ...... ................ ................ ................ ................ ................ .........26
5.6.2 Operation.................... ................ ................ ................ ................ .............27
5.6.3 Configuration.............................................................................................27
5.7 I-Luminate .....................................................................................................27
5.7.1 Description ...... ................ ................ ................ ................ ................ .........27
5.7.2 Operation.................... ................ ................ ................ ................ .............27
5.7.3 Configuration.............................................................................................27
5.8 Reading Environment.................... ................ ................ .................. ................ ...28
5.8.1 Description ...... ................ ................ ................ ................ ................ .........28
5.8.2 Operation.................... ................ ................ ................ ................ .............28
K5905271 DISPLAY CONTROLLER 27/02/2017
1
Table of contents
5.8.3 Configuration.............................................................................................29
5.9 Screen Capture ...............................................................................................29
5.9.1 Description ...... ................ ................ ................ ................ ................ .........29
5.9.2 Operation.................... ................ ................ ................ ................ .............29
5.9.3 Configuration.............................................................................................30
5.10 SingleView...... ................ ................ ................ ................ ................ ............... 30
5.10.1 Description .............. ................ ................ ................ ................ ................ .30
5.10.2 Operation.... ................ ................ ................ ................ ................ .............30
5.10.3 Configuration.............................................................................................30
5.11 SmartCursor...................................................................................................31
5.11.1 Description ...............................................................................................31
5.11.2 Operation.................................................................................................31
5.11.3 Configuration.............................................................................................31
5.12 SoftGlow ............ ................ ................ ................ ................ ................ ...........31
5.12.1 Description .............. ................ ................ ................ ................ ................ .31
5.12.2 Operation.... ................ ................ ................ ................ ................ .............32
5.12.3 Configuration.............................................................................................32
5.13 SpotView...... ................ ................ ................ ................ ................ ................ .32
5.13.1 Description .............. ................ ................ ................ ................ ................ .32
5.13.2 Operation.... ................ ................ ................ ................ ................ .............32
5.13.3 Configuration.............................................................................................33
5.14 Touchpad gestures............................................................................................34
5.14.1 Description .............. ................ ................ ................ ................ ................ .34
5.14.2 Operation.... ................ ................ ................ ................ ................ .............34
5.14.3 Configuration.............................................................................................35
5.15 VirtualView.....................................................................................................35
5.15.1 Description .............. ................ ................ ................ ................ ................ .35
5.15.2 Operation.... ................ ................ ................ ................ ................ .............36
5.15.3 Configuration.............................................................................................36
6. Important information .............................................. ............................. 39
6.1 Safety information............ ................ ................ ................ ................ ................ .39
6.2 Environmental information ...................................................................................39
6.3 Regulatory compliance information .............. ................ ................ ................ ...........41
6.4 Explanation of symbols.. ................ ................ ................ ................ ................ .....41
6.5 Legal disclaimer...............................................................................................43
6.6 Technical specifications ......................................................................................44
2
K5905271 DISPLAY CONTROLLER 27/02/2017
1. WELCOME!
1.1 About t he product
Display Controller
Thank you for choosing this Barco Display Controller!
1. Welcome!
Barco’s state-of-the-art Display Controllers deliver the performance, quality and stability r
day’s advanced medical imaging applications. The powerful boards ensure ultra-fast and smooth image
loading, and graphics processing of images in every resolution.
Use the instructions in this guide to install your Barco Display Controller.
equired for to-
1.2 What’s in the box
Contents
Your Barco Display Controller comes with:
• This Barco Display Controller User Guide
• 1 extender bracket is included with the MXRT-7600.
• 2 Single-Link Dongles are included with the MXRT-4500, MXRT-5500 & MXRT
•1low-profile bracket is included with the MXRT-2400, MXRT-2500 & MXRT-2600.
• 1 DMS-59-to-DVI adapter cable and 1 low-profile bracket are included with the MXRT-1450 & MXRT-
1451.
Keep your original pac kaging. It is designed for this Display Controller and is the ideal
protection during transport and storage.
-7500.
K5905271 DISPLAY CONTROLLER 27/02/2017 3
1. Welcome!
4 K5905271 DISPLAY CONTROLLER 27/02/2017
2. Display Controller installation
2. DISPLAY CONTROLLER INSTALLATION
2.1 Which Display Controller ?
Display Controller range
Your Barco medical display is compatible with a large range of Barco Display Controller boards. Depending on the order details, the display can be delivered with or without a Display Controller.
If you are installing a Barco Display Controller, please follow the installation instructions in this section.
Barco displays are compatible with a limited set of non-Barco display controllers. If you are installing a
non-Barco display controller, please consult its corresponding documentation.
2.2 Installing a Barco Display Controller
Guidance
This chapter will guide you through the physical installation of a Barco Display Controller for your display
system.
WARNING: Wear a grounded, protective ESD strap when handling or d uring installation
of the Display Controller. Electrostatic charges can damage the Display Controller.
Overview
Prior to installing the Barco Display Controller(s) for your Barco Display System in your workstation, please
take a few minutes to familiarize yourself with the Display Controller(s) and the PCIe slots.
Types of Display Controllers for Barco Display Systems
The following models of Barco Display Controllers are available for your display system. Please check
which of the following models is delivered with your system and follow the corresponding installation instructions:
Barco Model
Barco MXRT-1450 x11,x8,x16
Barco MXRT-1451 x11,x8,x16
Barco MXRT-2400 x16
Barco MXRT-2500 x16
Barco MXRT-2600 x16
Barco MXRT-4500
Barco MXRT-5400 x16
Barco MXRT-5450 x16
Barco MXRT-5500 x16
Barco MXRT-5550 x16
Barco MXRT-5600 x16
2
Compatible PCIe Slot
x16
1. Recommended PCIe slot. You can also use x16 & x8 slots for x1 boards.
2. Available in limited markets
K5905271 DISPLAY CONTROLLER 27/02/2017 5
2. Display Controller installation
Barco Model Compatible PCIe Slot
Barco MXRT-7400 x16
Barco MXRT-7500 x16
Barco MXRT-7600 x16
Which PCIe slot to use
The table above lists the various Display Controller model(s) available for your Barco Display System and
the recommended PCIe slot to use for optimum performance. The figure below shows the different types
of PCIe slots that can be used.
Image 2-1
Examples of PCIe slots
1
x16 slot
2
x8 slot
3
x1 slot
2.3 Installation pro ced ure
WARNING: Wear a grounded, protective ESD strap when handling or d uring installation
of the Display Controller. Electrostatic charges can damage the Display Controller.
If you are using a motherboard containing an on-board graphics solution and do not
intend to use it as part of a multiple-display setup, disable it either in the computer’s
System Set-up utility (BIOS) or the Windows d evice manager.
How to install
The following instructions will take you step by step through the installation of the Barco Display Controller(s) for your Barco Display System.
1. If you are not going to use your old Display Controller, uninstall its drivers and software.
2. Turn off the computer, display(s), and other peripheral devices.
3. Unplug the computer’s power cord and disconnect all cables from the back of your computer.
Warning:Wait approximately 20 seconds after unplugging the power cord before disconnecting a pe-
ripheral or removing a component from the motherboard to avoid possible damage to the
motherboard.
4. Remove the computer cover. If necessary, consult your computer’s manual for instructions.
5. If necessary, unscrew or unfasten and remove any existing display controller(s) from your computer.
6. Locate the appropriate slot and, if necessary, remove the metal back-plate cover(s).
7. Align the Barco Display Controller(s) for your Barco Display System with the slot(s) and press it(them)
in firmly until the card(s) is(are) fully se
6
ated.
K5905271 DISPLAY CONTROLLER 27/02/2017
2. Display Controller installation
8. Connect the power cable to the 6-pin power connection on the Display Controller. Make sure the cables
are not interfering with anything inside the computer (for example, a cooling fan).
Tip: This step only applies to the MXRT-7400, MXRT-7500 & MXRT-7600.
Image 2-2
Power connection for the M XRT-7400, MXRT-7500 & MXRT-7600 controllers
1
6-pin graphics controller power cable
9. Screw in or firmly fasten the Display Controller. Replace and secure the computer cover.
2.4 Connecting your Barco Displays
For a detailed description of the display installation and signal connection, please refer
to the Display User Guide.
IO-Panel for the Barco MXRT-1450 & MXRT-1451
Image 2-3
MXRT-1450 & MXRT-1451
DMS-59 connector provides DVI-I / Head 1 & Head 2 output connections through included the
1
Y-adapter cable.
IO-Panel for the Barco MXRT-2400 & MXRT-2500
Image 2-4
MXRT-2400 & MXRT-2500
K5905271 DISPLAY CONTROLLER 27/02/2017 7
2. Display Controller installation
1
DisplayPort Connection
2
DVI-I Connection
IO-Panel for the Barco MXRT-2600
Image 2-5
MXRT-2600
1
DisplayPort #1
2
DisplayPort #2
IO-Panel for the Barco MXRT-5450 & MXRT-5550
Image 2-6
MXRT-5450 & MXRT-5550
1
Head 1- DVI-I Connection
2
Head 2- DVI-I Connection
IO-Panel for the Barco MXRT-4500, MXRT-5400, MXRT-5500 & MXRT-7400
Image 2-7
MXRT-4500, MXRT-5400, MXRT-5500 & MXRT-7400
1
DisplayPort #1
2
DisplayPort #2
3
DVI-I
8 K5905271 DISPLAY CONTROLLER 27/02/2017
2. Display Controller installation
IO-Panel for the Barco MXRT-5600, MXRT-7500 & MXRT-7600
Image 2-8
MXRT-5600, MX RT-7500 & MXRT-7600
1
DisplayPort #1
2
DisplayPort #2
3
DisplayPort #3
4
DisplayPort #4
For displays with native DisplayPort input, use a native DisplayPort cable to connect the DisplayPort output
of the Display Controller to the DisplayPort input of the display. You cannot connect the DVI output of a
Display Controller to the DisplayPort input of a display.
2.5 Dongles
About
Barco dongles are designed to allow Barco Display Controllers with
with only a DVI input. Most current Barco displays support direct DisplayPort connection.
If video cable conversion is not required, you may bypass this section.
Barco dongles are available for purchase independently.
2.5.1 Passive Single-Link Dongle
About
The passive Single-Link Dongle converts DisplayPort input signals to single-link DVI output signals. It is
compatible with all Barco grayscale displays and up to 2MP color models. For color displays of 3MP and
greater resolutions, the Dual-Link Dongle is necessary.
a DisplayPort connector to a display
Image 2-9
Single-Link dongle
1
To display Single-Link DVI cable
2
To DisplayPort connector on Barco Display Controller
K5905271 DISPLAY CONTROLLER 27/02/2017
9
2. Display Controller installation
2.5.2 Active Single-Link Dongle
About
Barco Display Controllers are not compatible with third-party active single-link dongles. Please use Barco
passive Single-Link dongles.
2.5.3 Active Dual-Link Dongle
About
The active Dual-Link Dongle converts DisplayPort input signals to dual-link DVI output signals. Unlike the
passive Single-Link dongle, the Dual-Link dongle allows higher resolutions (greater than 1920x1200) on
color displays.
USB calibration must be used when connecting a display through a Dual-Link dongle.
Image 2-10
Dual-Link dongle
1
To computer’s USB port
2
To display via DVI Dual-Link cable
3
To DisplayPort connector on Barco Display Controller
2.6 Shipping the Barco Display Controller
About
After the installation and validation of software components, Barco recommends removing the display
controllers from the workstation and returning th
Barco does not recommend shipping display controllers installed in the workstation.
If it is necessary to ship a controller installed in a workstation, the MXRT-7600 requires an extender bracket
to protect against shock and vibration. Assemble the extender bracket as shown below. Refer to the
workstation user documentation on proper installation to its card guide.
em to their original packaging prior to shipment.
10
K5905271 DISPLAY CONTROLLER 27/02/2017
Image 2-11
MXRT-7600 Ex tender Bracket
1
Bracket
2
Extender
3
MXRT-7600
2. Display Controller installation
K5905271 DISPLAY CONTROLLER 27/02/2017
11
2. Display Controller installation
12 K5905271 DISPLAY CONTROLLER 27/02/2017
3. Driver and software installation
3. DRIVER AND SOFTWARE
INSTALLATION
3.1 Introduction
About
This chapter will guide you through the installation of the drivers, software and documentation associated
with your Barco Display System or Barco Display Controller(s).
Prerequisites
Before starting the installation of the Barco drivers, software and documentation following prerequisites
must be adhered:
• Your operating system must be installed and running. Following versions of Windows are supported:
- Windows 7 (32-bit or 64-bit)
- Windows 8.1 (64-bit)
- Windows 10 (64-bit)
• You must be logged on as a user with administrator privileges.
• All Barco displays must be connected to the appropriate Display Controller(s) in your system.
For optimal system performance, Barco recommends installing no more than two
drivers on a system at one time. If the configuration will require three drivers, the Barco
Driver Installer will alert the user to replace one board to eliminate one of the drivers.
• When there is a non-Barco board in the system, you must first ins
display controller before installing the Barco driver.
After each driver installation, you should reboot the system before proceeding with the
installation of another driver.
You will need to install the Barco Display Controller system drivers and software in the following cases:
• After you have installed the Barco Display Controller(s) for your Barco Display System in your system
for the first time.
• After you have reinstalled or upgraded your operating system.
• When upgrading to a newer version of the MXRT driver and software, manual uninstallation of the
prior version is not necessary. The Barco Product Installation Wizard will detect any prior installations
and start the uninstallation process automatically.
The installation dialog will display in English if
supported.
your operating system’s language is not
tall the driver for the non-Barco
K5905271 DISPLAY CONTROLLER 27/02/2017 13
3. Driver and software installation
3.2 Installation pro ced ure
Installation procedure
1. Start your system.
If you have a fresh OS installation, or you have uninstalled an existing driver, the OS may automatically
install an inbox driver from the Windows driver store, either an AMD driver or a standard VGA driver,
for the Barco Display Controller(s). If this occurs, the OS prompts you to restart your computer, click
Yes to allow the automatic driver installation to complete and reboot the system.
2. Launch the Barco Product Installation Wizard. The installation Wizard should start automatically when
you insert the Barco Display System Installation DVD into your computer’s DVD drive. If the installation
does not start, in the "auto play" window, click Run setup.exe.
3. The first page of the installation wizard is the license agreement. You must accept the license agree-
ment in order to proceed.
4. The second page of the installation wizard will show you the display controller driver and software com-
ponents that will be installed. To accept the installation of default software components, click Next.To
custom select software components, click on specific software components to unselect them.
Image 3-1
Barco Product Installation Wizard
- MXRT Driver and Intuitive Workflow Tools: Barco MXRT Display Controller drivers and accompanying software for supporting Intuitive Workflow tools
- BarcoMed Self Exam: Barco diagnostic tool
- MediCa l QAWeb Agent: Barco calibration software
5. If a previous installation of an MXRT driver ex
through the uninstallation process if necessary.
6. During installation, the desktop may flash, and the Installation Wizard window may appear on different
displays. This is expected behavior.
7. When the installation of all components has completed, the system must reboot to complete the
changes, and an automatic reboot win
dow will be displayed.
ists, the installation wizard will detect it and guide you
3.3 Silent inst allation
Installation procedure
Navigate to the Barco installation folder and execute the command setup.exe -silent.
14
K5905271 DISPLAY CONTROLLER 27/02/2017
Loading...