Barco MDRC-1119, MDRC-1119 TS, MDRC-1119 HB, MDRC-2120 User Manual

MDRC-1119
MDRC-2120

User manual

2

Copyright notice

This document is copyrighted. All rights are reserved. Nor this
document, nor any part of it, may be reproduced or copied in any form
or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems ­without written permission of Barco

© 2014 Barco N.V. All rights reserved.

3

Table of Contents

Table of Contents ....................................................................................... 3

Preface ........................................................................................................ 5

Important notice.................................................................................... 5

Environmental information ................................................................... 6

Recommendations for using your display system ............................. 10

Unpacking and handling tips .............................................................. 12

Preventing fire and injury ................................................................... 13

Cleaning the display ............................................................................ 13 

Shipping/storing the display .............................................................. 14

Explanation of symbols ....................................................................... 15

Introduction .............................................................................................. 16

About the product ............................................................................... 16

Package Overview ............................................................................... 18

Installation ................................................................................................ 19

Product Overview ................................................................................ 19

Front View ....................................................................................... 19

Back View ....................................................................................... 20

Tilt ........................................................................................................ 21

Kensington Security Slot ................................................................ 21

Start Your Installation .......................................................................... 21

Connecting the Display .................................................................. 22

Adjusting the screen position ............................................................. 24

User Controls ............................................................................................ 25

Jog Dial Controls .................................................................................. 25

How to Use the OSD Menus ................................................................ 26

On-Screen Display Menus ................................................................... 27

Appendix .................................................................................................. 45

Troubleshooting ................................................................................... 45

Warning Signal .................................................................................... 46

Product Dimensions MDRC-1119/MDRC-1119 TS/MDRC-1119 HB ... 47

Technical specifications MDRC-1119 .................................................. 48

Technical specifications MDRC-1119 TS .............................................. 50

Technical specifications MDRC-1119 HB ............................................. 52

Compatibility Modes MDRC -1119/MDRC-1119 TS/MDRC-1119 HB . 54

Product Dimensions MDRC-2120 ........................................................ 56

4

Technical specifications MDRC-2120 .................................................. 57

Compatibility Modes MDRC-2120 ....................................................... 59

Regulatory Compliance ....................................................................... 60

5

Preface

Important notice

Notice

Although every attempt has been made to achieve technical accuracy
in this document, we assume no responsibility for errors that may be
found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.

Barco software products are the property of Barco. They are distributed
under copyright by Barco N.V., for use only under the specific terms of
a software license agreement between Barco N.V. and the licensee.
No other use, duplication, or disclosure of a Barco software product, in
any form, is authorized.

The specifications of Barco products are subject to change without
notice.

Trademarks

All trademarks and registered trademarks are property of their
respective owners.

6

Environmental information

Disposal Information

The lamps inside the display contain mercury. Do not throw the display
in the trash. Dispose of it as required by local ordinances or regulations.

This equipment has required the extraction and use of natural
resources for its production. It may contain hazardous substances for
health and environment.

In order to avoid the dissemination of those substances in the
environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems.

Those systems will reuse or recycle most of the materials of your
end-of-life equipment in a sound way.

The crossed-out wheeled bin symbol invites you to use those
systems.

If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administrator.

You can also contact us for more information on the environmental
performances of our products.

7

Safety Instructions

General Recommendations

 Read the safety and operating instructions before operating the

display.

 Retain safety and operating instructions for future reference.
 Adhere to all warnings on the display and in the operating

instructions manual.

 Follow all instructions for operation and use.

Electrical shock

Warning- T

o prevent the risk of fire or shock hazards, do not expose

this product to rain or moisture

Warning-

Please do not open or disassemble the product as this

may

cause electric shock.

Warning-

Do not modify this equipment without authorization of the
manufacturer.

Warning-

To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.

Warning-

Make sure the user not to contact SIP/SOPs and the patient at
the same time.

Classification:

Electrical Shock Protection: Class I.

Disconnect Device: Connect / Remove power cord plug directly.

Degree of Protection Against Electric Shock: No applied part.

Degree of Protection Against Harmful Ingress of Water: Ordinary
equipment (IPX0).

8

Degree of Safety in the Presence of Flammable Anesthetic Mixture with
Air or with Oxygen or Nitrous Oxide: Not suitable for use in the
presence of a flammable anesthetic mixture with air or with oxygen or
nitrous oxide.

Mode of Operation: Continuous.

Intended use

This display is an AMLCD display designed for viewing medical X-ray
images. This unit should not be used near patients and should be kept
outside of 1.83 m perimeter and 2.29 m vertical.
The unit is not intended to be used in any life support system and
diagnosis.

Power connection

Power requirements: The display must be powered using a medical
approved 12VDC power supply (MDRC-1119, MDRC-1119TS,
MDRC-1119HB) or a 24VDC power supply (MDRC-2120).

The medical approved DC power supply must be powered by the AC
mains voltage.

Power requirements: The display must be powered using a medical
approved 24 VDC SELV power supply.

The medical approved DC power supply must be powered by the AC
mains voltage.

Power cords

Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent,
18 AWG min., rated 300 V min., provided with a hospital-grade type
plug 5-15P configuration for 120V application, or 6-15P for 240V
application.

9

Do not overload wall outlets and extension cords as this may result in
fire or electric shock.

Mains lead protection (U.S.: Power cord): Power cords should be routed
so that they are not likely to be walked upon or pinched by items
placed upon or against them, paying particular attention to cords at
plugs and receptacles.

Use a power cord that matches the voltage of the power outlet, which
has been approved and complies with the safety standard of your
particular country.

External equipment

External equipment intended for connection to signal input/output or
other connectors, shall comply with relevant UL/ EN/ IEC standard (e.g.
UL/EN/IEC 60950 for IT equipment and ANSI/AAMI ES60601-1/EN
60601-1 / IEC 60601 series for medical electrical equipment). In
addition, all such combinations – systems – shall comply with the
standard IEC 60601-1-1, Safety requirements for medical electrical
systems. Equipment not complying with ANSI/AAMI ES60601-1/EN /
IEC 60601-1 shall be kept outside the patient environment, as defined
in the standard.

Equipment not complying with IEC 60601 must be kept outside the
patient environment, as defined in the standard as at least 1.5 meters
from the patient or the patient support.

Any person who connects external equipment to signal input, signal
output, or other connectors has formed a system and is therefore
responsible for the system to comply with the requirements of IEC
60601-1-1. If in doubt, speak with a qualified technician.

In locations where 240V outlets are used, connect this display only on a
center-tapped, 240V, single-phase supply.

10

Water and moisture

Never expose the display to rain or moisture.

Never use the display near water - e.g. near a bathtub, washbasin,
swimming pool, kitchen sink, laundry tub or in a wet basement.

Ventilation

Do not cover or block the ventilation openings in the cover of the set.
When installing the display in a cupboard or another closed location,
heed the necessary space between the set and the sides of the
cupboard.

Installation

Place the display on a flat, solid and stable surface that can support the
weight of at least 3 displays. If you use an unstable cart or stand, the
display may fall, causing serious injury to a child or adult, and serious
damage to the equipment.

Recommendations for using your display system

1. Optimize the lifetime of your display

Enabling the Display Power Management System (DPMS) of your
display (in the display’s Settings menu) will optimize its lifetime by
automatically switching off the backlight when the display is not used
for a specified period of time. By default, DPMS is enabled on your
display, but it also needs to be activated on your workstation. To do
this, go to “Power Options Properties” in the “Control Panel”.

Barco recommends setting DPMS activation after 20 minutes of
non-usage.

11

2. Use a screen saver to avoid image retention

Prolonged operation of an LCD with the same content on the same
screen area may result in a form of image retention.

You can avoid or significantly reduce the occurrence of this
phenomenon by using a screen saver. You can activate a screen saver
in the “Display properties” window of your workstation.

Barco recommends setting screen saver activation after 5 minutes of
non-usage. A good screen saver displays moving content.

In case you are working with the same image or an application with
static image elements for several hours continuously (so that the
screen saver is not activated), change the image content regularly to
avoid image retention of the static elements.

3. Understand pixel technology

LCD displays use technology based on pixels. As a normal tolerance in
the manufacturing of the LCD, a limited number of these pixels may
remain either dark or permanently lit, without affecting the
performance of the product. To ensure optimal product quality, Barco
applies strict selection criteria for its LCD panels.

To learn more about LCD technology and missing pixels, consult the
dedicated white paper available at www.barco.com/healthcare.

4. Enhance user comfort

Every Barco multi-head display system is color matched with the
highest specification in the market.

Barco recommends keeping color-matched displays together.
Furthermore, it is important to use all displays of a multi-head
configuration at the same rate to preserve color matching throughout
the economic lifetime of the system.

12

5. Maximize Quality Assurance

The ‘MediCal QAWeb’ system offers online service for high-grade
Quality Assurance, providing maximum confidence and uptime.

Learn more and sign up for the free MediCal QAWeb Essential level at

www.barco.com/healthcare/qa

Unpacking and handling tips

The MDRC display is a precision instrument that requires proper care to
maintain product operation and adherence to specification. Unpack the
display and components carefully, then set up and handle the unit
properly to avoid damage to the LCD panel.

 Use both hands to grasp the display case when lifting it from

the shipping carton, but avoid touching the screen.

 Do not apply pressure to the screen or touch the screen with

bare fingers or objects. Pressure can affect image quality.
Cosmetics and oils on the skin are both detrimental to the
screen and difficult to remove.

 Allow the display to warm up to room temperature before

turning it on. Avoid sudden temperature changes in the
environment, as this may cause condensation, which damages
the display.

 Do not set up the display near strong light or heat sources.
 Do not block the vents on the back of the display or install the

display in a built-in enclosure. Blocked vents cause excessive
heat to build up inside the display, increasing risk of fire.

 When installing components, turn off your computer, but leave

it plugged into a grounded outlet.

 Do not remove the back cover or disassemble the display.

There are no user-serviceable parts inside.

13

Preventing fire and injury

 Replace the power supply or cables if damaged.
 Use only the power source indicated in this guide or listed on

the display.

 Do not plug the power supply into an overloaded AC outlet or

extension cord. Overloaded AC outlets and cords can result in
electric shock or fire.

 Do not drop or push objects into the display case. Internal

components contain high voltage.

 Unplug the power cord from the wall outlet during

thunderstorms.

 Do not place magnetic devices, such as motors, near the

display.

Cleaning the display

Observe the following guidelines to maintain display and LCD screen.

 Use a clean, lint-free, absorbent cotton cloth to clear off any

residual glue from removal of the protective film or to remove
surface dust. Apply light pressure to remove the dust.

 Dampen a clean cloth with a small amount of isopropyl alcohol

to remove glue or dust if the screen is still not clean. Do not
saturate the cloth; otherwise, alcohol may seep into the display
case and collect in the enclosure. Use a clean, dry cloth to
completely remove the alcohol residue.

 It is advised to clean the display on weekly basis.
 Do not use chemically treated dust cloths, acetone, toluene, or

harsh solvents on the display case or the screen. They can
damage the polarizer and the display case.

14

 Do not expose the display to water or excessive moisture. Do

not allow water or other stains to stand on the unit. Wipe
liquids off immediately to prevent damage to the display case
and the screen.

Shipping/storing the display

Keep the display in its shipping container until installation. Return the
display to its original container whenever you need to store the unit,
move it to another location, or return it for repair. The packaging
supplied by the manufacturer protects the display while it is in transit.
See environment specifications for more information.

Before returning the display to the container, do the following:

1 Swivel the display panel in landscape mode.

2 Push the panel down to the lowest position.

3 Use the stand lock to anchor the panel.

15

Explanation of symbols

DISPOSAL. Do not use household or municipal waste
collection services for disposal of electrical and electronic
equipment. EU countries require the use of separate
recycling collection services.

CAUTION. Read the accompanying text carefully for proper
operation and maintenance of the display system.

DIRECT CURRENT

ALTERNATING CURRENT

RELATIVE HUMIDITY
Storage & transport: 5%~ 90% (No condensation)
Operating: 8% ~ 80%

TEMPERATURE
Storage & transport: -20° to 60°
Operating: 0°~35°C

ISO 7000-1641. Follow operating instructions or consult
instructions for use.

16

Introduction

About the product

Thank you for choosing Barco.

The MDRC series are LCD displays with an active matrix, thin-film
transistor (TFT) liquid crystal display (LCD). These products also
demonstrate the following outstanding features:

MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB

 Dual Analog and Digital signal.
 19” diagonal Screen.
 1280x1024 high resolution.
 Wide Viewing Angle Technology.
 31.5 ~ 80 kHz horizontal scan.
 56 ~ 75 Hz refresh rate.
 Auto Adjustment and Re-scaling function.
 High quality full screen re-scaling capability.
 Multilingual OSD user controls.
 VESA DPM power saving.
 Kensington lock capability

17

MDRC-2120

 Dual Analog and Digital signal.
 20.1” diagonal Screen.
 1600x1200 high resolution.
 Wide Viewing Angle Technology.
 31.5 ~ 93.75 kHz horizontal scan.
 59 ~ 61 Hz refresh rate.
 Auto Adjustment and Re-scaling function.
 High quality full screen re-scaling capability.
 Multilingual OSD user controls.
 VESA DPM power saving.
 Kensington lock capability

18

Package Overview

USA Power Cord EUR Power Cord China Power Cord

Power Adapter

VGA Signal Cable DVI-D Cable User’s Manual

19

Installation

Product Overview

Front View

20

Back View

MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB

MDRC-2120

DC Power-In USB Ports

DVI-D Input

VGA Input

DC Power-In

USB Ports DVI-D Input

VGA Input

21

Tilt

Grasp the LCD Display with both hands and adjust the tilt as desired.

Kensington Security Slot

The Monitor can be secured to your desk or any other fixed object with
Kensington lock security products. Kensington lock is not included.

Kensington Security Slot

22

Start Your Installation

Connecting the Display

Use only the power adapter which are the forming part of each
medical device, the power cord, and the video cable shipped with this
display.

CAUTION: For MDRC-1119 / MDRC-1119 TS: The universal external 12V
DC/ 5.0A power adapter (100-240V~, 1.5A, 50-60Hz for power adapter
rating) is the BridgePower (BPM060S12F09). For MDRC-2120: The
universal external 24V DC/ 2.7A power adapter (100-240V~, 1.5A,
50-60Hz for power adapter rating) is the BridgePower
(JMW190KB1200F09). For MDRC-1119 HB: The universal external 12 V
DC / 7.0A power adapter (100-240V~, 2.0A, 50-60Hz for power
adapter rating) is the BridgePower (JMW190KB1200F09).

To setup this display, please refer to the following figure and
procedures.

1. Be sure all equipment is turned off.

2. Connect the DC power cord to the power connector; plug one

end of the AC power cord into the power adapter, and the

other end into an electrical outlet. (1).

3. For a PC with Analog output: Connect the VGA signal cable

from display VGA input connector to the 15-pin connector of

your host computer and tighten the screws. (2).

4. For a PC with DVI digital output: Connect the DVI signal cable

to the connector of the display card in your computer, connect
the other side to the DVI-D input port of your display. Tighten

the screws (3).

5. Turn on your computer, display and video source.

Note: To ensure the LCD Display will work well with your computer,
please configure the display mode of your graphics card to make it less

23

than or equal to the native resolution, and make sure the timing of the
display mode is compatible with the LCD screen. We have listed the
“Compatibility Modes” of this LCD screen in appendices for your
reference.

24

Adjusting the screen position

Vertical Height

Portrait/Landscape

Left to Right Pan

Front to Back Tilt

Remove Monitor

Stand may forcefully extend and cause injury
Lift Monitor to "Full UP" position in advance
Picking up the base or removing the monitor

25

User Controls

Jog Dial Controls





26

No./ Icon Control Function



Jog Dial button

- Power Switch

- Menu

1.

Press the jog dial button for 1 sec
to power off to the LCD Display.

2. Swivel jog dial button for OSD
menu

 LED

Power LED

1. Green indicates the display is

turned on.

2. Orange indicates the display is

in stand-by mode.

How to Use the OSD Menus

1. Swivel the Jog dial button to pop up the ”on-screen menu”

and to scroll among the six Main Menus.

2. Choose the adjustment items by pressing the jog dial button.

3. Adjust the value of the adjustment items by swiveling the jog

dial button.

4. After a period of inactivity *(based on a user setting), the OSD

menus will automatically disappear.

27

On-Screen Display Menus

Main Menu

Function Description

Input Selection Go to the ‘Input Selection Menu’ while the

jog-dial button is pressed.

Adjustments Go to the ‘Adjustment Menu’ while the

jog-dial button is pressed.

28

Color Go to the ‘Color Menu’ while the jog-dial

button is pressed.

Geometry* Go to the ‘Geometry Menu’ while the

jog-dial button is pressed.

Settings Go to the ‘Settings Menu’ while the

jog-dial button is pressed.

Information Go to the ‘Information Menu’ while the

jog-dial button is pressed.

Exit Close this menu.

29

Input selection Menu

Function Description

DVI Select the DVI input while the jog-dial

button is pressed.

VGA Select the VGA input while the jog-dial

button is pressed.

Back Go back to the ‘Main Menu’.

Exit Close this menu.

30

Adjustments Menu

Function Description

Brightness To adjust the backlight luminance..

Contrast** To adjust the image contrast (only applicable

if VGA is selected).

Sharpness** Manual adjustment of the image sharpness

(only applicable if VGA is selected)

Gamma Go to the ‘Gamma Menu’ while the jog-dial

button pressed.

Exit Close this menu.

31

Adjustments -> Gamma menu

Function Description

Native Select the panel original gamma.

Gamma 1.8 Select the Dynamic Gamma 1.8.

Gamma 2.2 Select the Dynamic Gamma 2.2.

Dicom Select the Dicom.

User Select the user defined gamma which built

by QAWeb Agent tool.

Back Go back to the ‘Adjustments Menu’

Exit Close this menu.

32

Color Menu

Function Description

Native Select the panel original color temperature.

Clearbase Set the image color temperature to Clearbase

Bluebase Set the image color temperature to Bluebase

User Go to the ‘User Menu’ while the jog-dial button

pressed.

Back Go back to the ‘Adjustments Menu’.

33

Exit Close this menu.

Color Menu -> User Menu

Function Description

Red Turn red gain value manually.

Green Turn green gain value manually.

Blue Turn blue gain value manually.

Back Go back to the ‘Color Menu’.

Exit Close the menu.

34

Geometry Menu**

Function Description

Auto set Adjust the image parameters to obtain a correctly

aligned image automatically while the jog-dial
button pressed.

clock Adjust the internal clock frequency manually.

Increase this value to make the image wider,
decrease this value to make the image smaller.

Phase Adjust the internal clock phase manually. If this

setting is not correct, the vertical bands with
alternate intensity will be visible.

35

Horizontal position Adjust the image horizontal position manually.

Vertical position Adjust the image vertical position manually.

Exit Close this menu.

36

Setting Menu

Function Description

OSD Setting Go to the ‘OSD Settings menu’ while the

jog-dial button is pressed.

Factory Reset Go to the ‘Factory Reset Menu’ while the

jog-dial button is pressed.

Language Go to the ‘Language Menu’ while the jog-dial

button is pressed.

37

Power Save Go to the ‘Power Save Menu’ while the

jog-dial button is pressed.

LED Go to the ‘LED Menu’ while the jog-dial button

is pressed.

Back Go back to the ‘Main Menu’.

Exit Close this menu.

38

Settings Menu -> OSD Settings Menu

Function Description

OSD Timeout Set the OSD timeout value.

OSD Horizontal Set the OSD horizontal alignment

OSD Vertical Set the OSD vertical alignment

OSD Direction Go to the ‘OSD Direction Menu’ while the jog-dial

button pressed.

Back Go back to the ‘Settings Menu’.

Exit Close the menu.

39

Settings Menu -> OSD Settings Menu -> OSD Direction

Function Description

Landscape Select OSD Landscape.

Portrait Select OSD Portrait.

Back Go back to the ‘OSD Settings Menu’.

Exit Close the menu.

40

Settings Menu -> Factory Reset Menu

Function Description

Yes Execute the ‘Factory Reset’.

No Abort the ‘Factory Reset’.

Back Go back to the ‘Settings Menu’.

Exit Close the menu.

41

Settings Menu -> Factory Reset Menu

Function Description

English Execute the ‘Factory Reset’.

Français Select 'Français' as the OSD words while the

jog-dial button pressed.

Deutsch Select 'Deutsch' as the OSD words while the

jog-dial button pressed.

Español Select 'Español' as the OSD words while

thejog-dial button pressed.

Italiano Select 'Italiano' as the OSD words while the

jog-dial button pressed.

Nederlands Select 'Nederlands' as the OSD words while

thejog-dial button pressed.

日本語 Select '日本語' as the OSD words while the

jog-dial button pressed.

简体中文 Select '简体中文' as the OSD words while the

jog-dial button pressed.

繁體中文 Select '繁體中文' as the OSD words while the

jog-dial button pressed.

한국 Select '한국' as the OSD words while the jog-dial

button pressed.

Back Go back to the ‘Settings Menu’.

Exit Close the menu.

42

Settings Menu -> Power Save Menu

Function Description

On Enable the ‘Power Save’ function.

Off Disable the ‘Power Save’ function.

Back Go back to the ‘Settings Menu’.

Exit Close the menu.

43

Settings Menu -> LED Menu

Function Description

On Enable the LED.

Off Disable the LED.

Back Go back to the ‘Settings Menu’.

Exit Close the menu.

44

Information Menu

Function Description

FW version Firmware version

System hours System run time

Backlight run time Backlight run time

Back Go back to the ‘Main Menu’.

Exit Close the menu.

Notes 1：Symbol (*) means only active while VGA is selected.
Otherwise, it will be un-selectable with gray color, and the
subordinate items are blocked.

Note 2: Symbol (**) means only active while VGA is selected. Oth­erwise, it will be not selectable with gray color.

45

Appendix

Troubleshooting

If you are experiencing trouble with the LCD display, refer to the
following troubleshooting. If the problem persists, please contact your
local dealer or our service center.

Problem: No image appears on screen.

 Check that all the I/O and power connectors are correctly and

well connected as described in the “Installation” section.

 Make sure the pins of the connectors are not crooked or

broken.

Problem: Partial image or incorrectly displayed image.

 Check to see if the resolution of your computer is higher than

that of the LCD Display.

 Reconfigure the resolution of your computer to make it less

than or equal to the native resolution MDRC-1119, MDRC-1119
TS and MDRC-1119 HB (1280 x 1024) MDRC-2120(1600 x1200)

Problem: Image has vertical flickering line bars.

 Use “Clock” to make an adjustment.
 Check and reconfigure the display mode of the vertical refresh

rate of your graphics card to make it compatible with the LCD
Display.

46

Problem: Image is unstable and flickering

 Use “Phase” to make an adjustment.

Problem: Image is scrolling

 Check and make sure the VGA signal cable (or adapter) is well

connected.

 Check and reconfigure the display mode of the vertical refresh

rate of your graphics card to make it compatible with the LCD
Display.

Problem: Vague image (characters and graphics)

 Use “Clock” to make an adjustment. If this problem still exists,

use “Phase” to make an adjustment.

Warning Signal

Sometimes you may see warning messages for this LCD Display. This
means that the LCD Display cannot correctly receive the signal from the
computer graphics card.

No Signal

This message means that the LCD Display has been powered on but it
cannot receive any signal from the computer graphics card. Check all
the power switches, power cables, and VGA signal cable.

Out Of Range

This message means that the signal of the computer graphics card is
not compatible with the LCD Display. When the signal is not included in
the compatibility mode we have listed in the Appendices of this
manual, the LCD display will show this message.

47

Product Dimensions MDRC-1119/MDRC-1119
TS/MDRC-1119 HB

48

Technical specifications MDRC-1119

LCD Panel MDRC-1119

Technology TFT Color LCD (VA)

Native resolution 1280 x1024

Active screen diagonal 19" (483 mm)

Active screen area 376 x 301 mm

Pixel Pitch 0.294 x 0.294

Visual Characteristic

Maximum luminance 300 cd/m2

DICOM calibrated luminance 180 cd/m2

Image stabilization BLOS (Backlight sensor)

Contrast ratio 1300:1

Aspect ratio 5:4

Viewing angle (CR>10) 178°/178°

Display LUT 10 bit

Response time (G-G) 8 ms

Display Functions Gamma, Dicom

Colors 16.7 million

Connectivity and control

Video Input DVI

VGA (DB15)

USB (1 upstream, 2 downstream)

49

OSD languages English, French, German, Spanish, Italian, Dutch,

Simplified Chinese, Traditional Chinese, Korean.

Options

Protective Cover Yes

Touch Screen No

Landscape/Portrait Yes

Certifications

EMC EN 60601-1-2; FCC-B; ICES-001, VCCI, KETI, CCC,

BSMI

Safety CE EN60601-1; UL ANSI/AAMI ES60601-1,

c-UL, CAN/CSA-C22.2 NO. 60601-1, CCC, KETI,
PSE, BSMI

Mechanical characteristics

Display dimensions (W x H x D)
Landscape, w/o pedestal

418 x 346 x 70 mm

Display weight With Stand : 8.75 kg

Without Stand : 5.65 kg

Display stand Tilt, height & swivel

Mounting VESA 100x100

WARNING: use suitable mounting apparatus to
avoid risk of injury.

Power requirements

System rating Input: 12Vdc/5A

External DC Power Supply Input: 90V-264V (50Hz-60Hz), 1.5A

Output: 12Vdc/5A
For only use power supply BridgePower:
BPM060S12F09

Standby Power < 1 W

Power consumption 50 Watts

50

Environmental

Operating T (min-max) 0° to 35°C (32° to 95°F)

Humidity 8% - 80% (no condensation)

Storage & Transport Humidity 5% - 90% (no condensation)

Technical specifications MDRC-1119 TS

LCD Panel MDRC-1119 TS

Technology TFT Color LCD (VA)

Native resolution 1280 x1024

Active screen diagonal 19" (483 mm)

Active screen area 376 x 301 mm

Pixel Pitch 0.294 x 0.294

Visual Characteristic

Maximum luminance 300 cd/m2

DICOM calibrated luminance 180 cd/m2

Image stabilization BLOS (Backlight sensor)

Contrast ratio 1300:1

Aspect ratio 5:4

Viewing angle (CR>10) 178°/178°

Display LUT 10 bit

Response time (G-G) 8 ms

Display Functions Gamma, Dicom

Colors 16.7 million

51

Connectivity and control

Video Input DVI

VGA (DB15)

USB (1 upstream, 2 downstream)

OSD languages English, French, German, Spanish, Italian, Dutch,

Simplified Chinese, Traditional Chinese, Korean.

Options

Protective Cover No

Touch Screen Yes

Landscape/Portrait Yes

Certifications

EMC EN 60601-1-2; FCC-B; ICES-001, VCCI, KETI, CCC,

BSMI

Safety CE EN60601-1; UL ANSI/AAMI ES60601-1, c-UL

CAN/CSA-C22.2 NO. 60601-1, CCC, KETI, PSE,
BSMI

Mechanical characteristics

Display dimensions (W x H x D)
Landscape, w/o pedestal

418 x 346 x 70 mm

Display weight With Stand : 9.39 kg

Without Stand : 6.29 kg

Display stand Tilt, height & swivel

Mounting VESA 100x100

WARNING: use suitable mounting apparatus to
avoid risk of injury.

Power requirements

System rating Input: 12Vdc/5A

External DC Power Supply Input: 90V-264V (50Hz-60Hz), 1.5A

52

Output: 12Vdc/5A
For only use power supply BridgePower:
BPM060S12F09

Standby Power < 1 W

Power consumption 50 Watts

Environmental

Operating T (min-max) 0° to 35°C (32° to 95°F)

Humidity 8% - 80% (no condensation)

Storage & Transport Humidity 5% - 90% (no condensation)

Technical specifications MDRC-1119 HB

LCD Panel MDRC-1119

Technology TFT Color LCD (VA)

Native resolution 1280 x1024

Active screen diagonal 19" (483 mm)

Active screen area 376 x 301 mm

Pixel Pitch 0.294 x 0.294

Visual Characteristic

Maximum luminance 600 cd/m2

DICOM calibrated luminance 300 cd/m2

Image stabilization BLOS (Backlight sensor)

Contrast ratio 2000:1

Aspect ratio 5:4

Viewing angle (CR>10) 178°/178°

53

Display LUT 10 bit

Response time (G-G) 8 ms

Display Functions Gamma, Dicom

Colors 16.7 million

Connectivity and control

Video Input DVI

VGA (DB15)

USB (1 upstream, 2 downstream)

OSD languages English, French, German, Spanish, Italian, Dutch,

Simplified Chinese, Traditional Chinese, Korean.

Options

Protective Cover No

Touch Screen No

Landscape/Portrait Yes

Certifications

EMC EN 60601-1-2; FCC-B; ICES-001, VCCI, KETI, CCC,

BSMI

Safety CE EN60601-1; UL ANSI/AAMI ES60601-1, c-UL

CAN/CSA-C22.2 NO. 60601-1, CCC, KETI, PSE,
BSMI

Mechanical characteristics

Display dimensions (W x H x D)
Landscape, w/o pedestal

418 x 346 x 70 mm

Display weight With Stand : 7.61 kg

Without Stand : 4.42 kg

Display stand Tilt, height & swivel

Mounting VESA 100x100

54

WARNING: use suitable mounting apparatus to
avoid risk of injury.

Power requirements

System rating Input: 12Vdc/7A

External DC Power Supply Input: 90V-264V (50Hz-60Hz), 2.0A

Output: 12Vdc/7A
For only use power supply BridgePower:
JMW190KB1200F09

Standby Power < 1 W

Power consumption 45 Watts

Environmental

Operating T (min-max) 0° to 35°C (32° to 95°F)

Humidity 8% - 80% (no condensation)

Storage & Transport Humidity 5% - 90% (no condensation)

Operating altitude 3,048m

Compatibility Modes MDRC -1119/MDRC-1119
TS/MDRC-1119 HB

Standard Resolution

Vertical
Refresh
(Hz)

Horizontal
Scan
(KHz)

IBM VGA
IBM VGA
IBM VGA

640x350
640x480
720x400

70
60
70

31.5

31.5

31.5

55

VESA VGA
VESA VGA

VESA SVGA
VESA SVGA
VESA SVGA
VESA SVGA

640x480
640x480

800x600
800x600
800x600

800x600

72
75

56

60
72

75

37.9

37.5

35.1

37.9

48.1

46.9

VESA XGA
VESA XGA
VESA XGA

1024x768
1024x768

1024x768

60
70

75

48.4

56.5

60.0

VESA XGA
VESA XGA

1152x870
1152x864

60
75

54.36

68.1

VESA SXGA
VESA SXGA

1280x1024
1280x1024

60
75

63.96

79.95

Apple Mac II
Apple Mac
Apple Mac

640x480
832x624

1024x768

67
75

75

35.0

49.7

60.2

56

Product Dimensions MDRC-2120

57

Technical specifications MDRC-2120

LCD Panel MDRC-2120

Technology TFT Color LCD (IPS)

Native resolution 1600 x1200

Active screen diagonal 20.1" (510.54 mm)

Active screen area 432 x 331.5 mm

Pixel Pitch 0.255 x 0.255

Visual Characteristic

Maximum luminance 300 cd/m2

DICOM calibrated luminance 180 cd/m2

Image stabilization BLOS (Backlight sensor)

Contrast ratio 800:1

Aspect ratio 4:3

Viewing angle (CR>10) 178°/178°

Display LUT 10 bit

Response time (G-G) 6 ms

Display Functions Gamma, Dicom

Colors 16.7 million

Connectivity and control

Video Input DVI

VGA (DB15)

USB (1 upstream, 2 downstream)

58

OSD languages English, French, German, Spanish, Italian, Dutch,

Simplified Chinese, Traditional Chinese, Korean.

Options

Protective Cover Yes

Touch Screen No

Landscape/Portrait Yes

Certifications

EMC EN 60601-1-2; FCC-B; ICES-001, VCCI, KETI, CCC,

BSMI

Safety CE EN60601-1; UL ANSI/AAMI ES60601-1, c-UL

CAN/CSA-C22.2 NO.60601-1, CCC, KETI, PSE,
BSMI

Mechanical characteristics

Display dimensions (W x H x D)
Landscape, w/o pedestal

455 x 354 x 70 mm

Display weight With Stand : 9.8 kg

Without Stand : 6.0 kg

Display stand Tilt, height & swivel

Mounting VESA 100 x 100 mm

WARNING: use suitable mounting apparatus to
avoid risk of injury.

Power requirements

System rating Input: 24Vdc/2.7A

External DC Power Supply Input: 90V-264V (50Hz-60Hz), 1.5A

Output: 24Vdc/2.7A
For only use power supply BridgePower:
BPM060S24F09

Standby Power < 1 W

Power consumption 55 Watts

59

Environmental

Operating T (min-max) 0° to 35°C (32° to 95°F)

Operating Humidity 8% - 80% (no condensation)

Storage & Transport Humidity 5% - 90% (no condensation)

Compatibility Modes MDRC-2120

Standard Resolution Vertical Re-

fresh (Hz)

Horizontal
Scan (KHz)

VGA 640x480 60 31.50

SVGA 800x600 60 37.68

XGA 1024x768 60 48.36

1152*870 60 54.36

SXGA 1280*1024 60 63.96

1MP2FH 1280*1024 60 62.50

1024*1280 59 77.78

UXGA 1600*1200 60 75.00

2MP2FH 1600*1200 59 72.81

1200*1600 59 95.84

60

Regulatory Compliance

Canada, European Union, United States

This display has been tested and
found to comply with IEC/EN 60601-1
and IEC 60601-1-2 standards, and is
certified to meet medical standard
ANSI/AAMI ES60601-1 and CAN/CSA

C22.2 No 60601.1(C US Mark) which
are related to electrical shock, fire and mechanical hazards only as
shown on right UL mark on this page.

The medical display, in addition to meeting medical requirements, has
been tested and found to comply with the limits for Federal
Communications Commission (FCC) Class B computing devices in a
typically configured system since many medical offices are located in
residential areas. It is the system integrator’s responsibility to test and
ensure that the entire system complies with applicable
electromagnetic compatibility (EMC) laws.

Barco NV has made great efforts to support the medical device industry,
in particular, medical device manufacturers and medical device system
integrators. We offer state-of-the-art color displays that are compliant
with worldwide accepted medical device safety standards, and for the
European market, CE-marked displays based on compliance with
counsel directive 93/42/EEC—commonly referred to as the Medical
Device Directive (MDD). The following summarizes our qualification of
these displays as it relates to compliance with the MDD.

61

The European Medical Device Directive requires that the intended use
of the device be defined. The intended use of these displays is “to
display alphanumeric, graphic, and image data as inputted from any
type of medical device.” These displays do not provide a measurement
function in any way, and it is the device and systems manufacturer’s
responsibility to verify its function in the integrated device or system.

The display was classified as required by the MDD according to Annex
IX of the directive and the medical device (MEDDEV) guidance available
at the time of classification. Because the display uses electrical energy
and has no direct patient connections and—by itself—no medical utility,
the display is classified according to Rule 12 as an MDD Class I device,
component, or accessory. The MDD states that manufacturers of Class I
medical devices or accessories shall satisfy the requirements in regard
to design and manufacturing controls, that is, the applicable
assessment route to be used for CE-marking under the MDD, and it
shall carry the CE mark according to Annex XII of the directive, with no
notified body annotation.

In the opinion of Barco NV registration required to put this device into
commerce is the responsibility of the medical device/system
manufacturer, and Barco supports this requirement by providing a
European Commission (EC) declaration of conformity. If Barco supplies a
display to an end user, rather than a device manufacturer, it is the end
user’s responsibility to ensure continued compliance with the MDD of
the system in which the display is integrated.

The supplier will make available on request, circuit diagrams,
component part lists, etc.

For vigilance reporting as required under Article 10 of the MDD, Barco
NV will provide any information requested by competent authority to
support any reported incident investigation by such an authority.

62

EU Declaration of Conformity for Medical Application

A Declaration of Conformity has been filed for this product. For
additional copies of the Declaration of Conformity document, contact
Barco NV

The MDRC series digital flat-panel display meets the essential health
and safety requirements, is in conformity with, and the CE marking has
been applied according to the relevant EU Directives listed below, using
the relevant section of the following EU standards and other normative
documents;

EU EMC Directive 89/336/EEC

EU Electromagnetic Compatibility Directive

EN 60601-1-2 (2001) Collateral standard

electromagnetic

Medical Electrical Equipment compatibility requirements

EN 55011 (Class B) Limits and methods of

measurements for radio
interference characteristics of
industrial, scientific, and medical
equipment

IEC 61000-3-2 Harmonic emissions

IEC 61000-3-3 Voltage fluctuations/flicker

emissions

IEC 61000-4-2 Electrostatic discharge

requirements for industrial
process measurement and control
equipment

IEC 61000-4-3 Radiated electromagnetic field

requirements for industrial

63

process measurement and control
equipment

IEC 61000-4-4 Electrically fast transients for

industrial process measurement
and control equipment

IEC 61000-4-5 Surge requirements

IEC 61000-4-11 Voltage variations/dips/interrupts

IEC 61000-4-6 Conducted immunity

IEC 61000-4-8 Magnetic field immunity

Conformance to the Medical

Device Directive 93/42/EEC

EN 60601-1 Medical Part 1 General requirements for safety

Electrical Equipment.

U.S. FCC Compliance Statement

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.

NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communications.

64

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technical for

help.

CAUTION: Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

Other countries

Japan VCCI level B

Korea KETI level B

PRC CCC level B

Taiwan BSMI level B

65

B4100531-05

January 2014

Barco nv

President Kennedypark 35

8500 Kortrijk

Belgium

www.barco.com