Barco MDCG-5221 User Manual

Coronis 5MP LED Display

User Guide

MDCG-5221

K5902074/02
19/12/2014

Barco nv
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/esupport
Visit us at the web: www.barco.com

PrintedinBelgium

Table of contents

TABLE OF CONTENTS

1. Welcome! ......... ............................................................ ..................... 3

1.1 About the product ............................................................................................. 3

1.2 What’s in the box.............................................................................................. 3

2. Parts, controls and connectors .................................. ............................. 5

2.1 Display front view .. ................ ................ ................ ................ ................ ........... 5

2.2 Display rear view.............................................................................................. 6

3. Display installation ................... ........................................................... 9

3.1 Unlocking the height mechanism............................................................................ 9

3.2 Adjusting the display position....... ................ ................ ................ ................ ......... 9

3.3 Removing the connector compartment cover ..............................................................10

3.4 Connecting the signal cables ................................................................................11

3.5 Routing the cables & Reattach the connector compartment cover ......... ................ .............12

3.6 VESA-mount installation .....................................................................................13

3.7 First time starting up ..........................................................................................14

4. Daily operation ......... .................................................................... ...... 15

4.1 Recommendations for daily operation ................... ................ ................ ................ ...15

4.2 Key indicator lights..... .................. ................ ................ ................ ................ .....16

4.3 Standby switching.............................................................................................16

4.4 Bringing up the OSD menus .......... ................ ................ ................ ................ .......17

4.5 Navigating through the OSD menus ..... ................ ................ ................ ................ ...17

4.6 I-Luminate .....................................................................................................18

5. Advanced operation .................. ........................................................... 19

5.1 OSD menu language .... ................ ................ .................. ................ ................ ...19

5.2 OSD menu automatic close function........... ................ ................ ................ .............19

5.3 Power status indicator light ..................................................................................19

5.4 Key indicator lights..... .................. ................ ................ ................ ................ .....20

5.5 Power lock function .......... ................ ................ ................ ................ ................ .20

5.6 Ethernet over USB ............................................................................................20

5.7 USB.............. ................ ................ ................ ................ ................ ............... 21

5.8 DPMS mode ........ ................ ................ ................ ................ ................ ...........21

5.9 Hibernate...... ................ ................ ................ ................ ................ ................ .22

5.10 I-Luminate default mode .................... ................ ................ ................ ................ .22

5.11 Luminance target................. ................ ................ ................ ................ .............23

5.12 Viewing modes ................................................................................................23

5.13 Display functions ..............................................................................................24

5.14 Ambient Light Compensation (ALC) ................... ................ ................ ................ .....24

5.15 Reading rooms ... ................ ................ ................ ................ ................ .............25

5.16 Continuous ALC...............................................................................................26

5.17 Embedded QA.................... ................ ................ ................ ................ .............26

5.17.1 About Embedded QA ...................................................................................26

5.17.2 DICOM status report ............... ................ ................ ................ ................ .....27

5.17.3 DICOM compliance check....... ................ ................ ................ ................ .......27

5.17.4 DICOM calibration.......................................................................................28

5.17.5 Reset DICOM calibration .. ................ ................ ................ ................ .............28

5.17.6 DICOM error threshold..................................................................................28

5.18 Image scaling..................................................................................................28

5.19 Display orientation ............................................................................................29

5.20 Video input signals............................................................................................29

5.21 Video encoding modes .................. ................ ................ ................ .................. ...29

5.22 Grayscale conversion modes................................................................................30

5.23 EDID timings...................................................................................................31

5.24 Display info ......... ................ ................ ................ ................ ................ ...........31

5.25 Display status............. ................ ................ ................ ................ ................ .....31

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

1

Table of contents

6. Repackaging instructions ...................................................................... 33

6.1 Replacing the protection buffer ............... ................ ................ ................ ............... 34

7. Cleaning your display ............................... ............................................ 35

7.1 Cleaning instructions .........................................................................................35

8. Important information ......... .................................................................. 37

8.1 Safety information...... .................. ................ ................ ................ ................ .....37

8.2 Environmental information ...................................................................................38

8.3 Regulatory compliance information .......... ................ ................ ................ ............... 41

8.4 EMC notice ... ................ ................ ................ ................ ................ ................ .41

8.5 Explanation of symbols .............. .................. ................ ................ ................ .......45

8.6 Legal disclaimer ...............................................................................................47

8.7 Technical specifications ......................................................................................48

8.8 Open source license information ......... .................. ................ ................ ................ .49

2

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

1. WELCOME!

1.1 About the product

Overview

Thank you for choosing this Coronis 5MP LED Display!

1. Welcome!

Coronis 5MP LED Display is the industry-leading display system for grayscale radiology imaging.
livers optimum diagnostic precision and workflow efficiency for high-resolution PACS imaging, CT, MRI,
chest radiology, angiography, etc.

50 more shades of gray

Barco’s high-bright LED backlights render more Just Noticeable Differences to help you see more shades
of gray. By making subtle details more noticeable more quickly, Coronis 5MP LED Display reduce
dowing and leveling time so you can read more studies each day.

Perfect images

Barco’s image-enhancing technologies — designed for the unique characteristics of LED backlit medical
displays — ensure perfect image quality at all times. PPU-LED removes panel noise and renders uniform
DICOM images from center to corner. An Intelligent Multi Sensor Techn
Barco’s patented I-Guard front-of-screen sensor with backlight, ambient light and temperature sensors to
optimize image quality and keep it consistent over time.

Green performance

Using energy-efficient LED backlights, Barco’s Coronis 5MP LED Display is as low in power consumption
as it is high in brightness. Additionally, Barco’s LED backlights a
last longer. This allows Barco to guarantee a 5-year backlight warranty.

Worryfree DICOM compliance

Barco’s Coronis 5MP LED Display is bundled with MediCal QAWeb for automated calibration and QA,
ensuring continuous diagnostic quality and maximum uptime of your workstation. MediCal QAWeb allows
you to continue working while automated QA checks ar
secure online web service for remote, centralized image quality management.

e being executed. The system also includes a

re mercury-free, produce less heat, and

ology system (I-MST) combines

It de-

swin-

I-Luminate™

One push ’hot light’ brightness boost for inspection of subtle details or comparing with film-based priors.

CAUTION: Read all the important safety information before installing and operating your

Coronis 5MP LED Display. Please refer to the dedicat

ed chapter in this user guide.

1.2 What’s in the box

Overview

Your Coronis 5MP LED Display comes with:

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

3

1. Welcome!

• the display

• a system tilt and swivel foot

• this Coronis 5MP LED Display user guide

• a system CD

• a DisplayPort cable

•aDVIcable

•anUSBcable

•anACpowercord

• an external power supply

If you ordered a Barco display controller, it’s also in the box together with its accessories. A dedicated
user guide is available on the system CD.

Keep y our original packaging. It is designed for this display and is the ideal protection
during transport and storage.

4 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

2. Parts, controls and connectors

2. PARTS, CONTROLS AND
CONNECTORS

2.1 Display front view

Overview

6

1 2 4 5

Image 2-1
Front view

I-Luminate/Left key

1

Right key

2

Menu key

3

Standby key

4

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

3

Power LEDs

5

Ambient light sensor

6

Bottom downstream USB

7

7

5

2. Parts, controls and connectors

2.2 Display rear view

Connector compartment cover closed

Image 2-2
Rear view with closed connector compartment cover

Connector compartment cover

1

Cable duct

2

3

4

Foot lock clip

Tilt & swivel foot

6

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

Connector compartment cover open

2. Parts, controls and connectors

Image 2-3
Rear view with open connector compar

+24 VDC power input

1

+5 VDC, 0.5A power output

2

DisplayPort video input

3

DVI video input

4

The Ethernet connection is used for maintenance purposes and is not supported for
user application.

tment cover

Ethernet connector (see note

5

below)
USB upstream connector

6

USB downstream connector

7

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 7

2. Parts, controls and connectors

8 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

3. DISPLAY INSTALLATION

Prior to installing your Coronis 5MP LED Display and connecting all necessary cables,
make sure to have a suitable display controller physically installed in your computer. If
you are using a Barco display controller, please consult the user guide delivered with it
to do this.

For a list of compatible display controllers, please refer to t he latest version of the com­patibility matrix availabl e on m
patibility Matrices > Barco Systems Compatibility Matrices).

3.1 Unlocking the height mechanism

To remove the clip:

1. Position the display with its rear side facing you.

2. Pull the red clip out of the fixation hole in the foot.

yBarco.com (myBarco > My Support > Healthcare > Com-

3. Display installation

3. Keep the clip in the dedicated hole in case the display needs to be shipped later.

3.2 Adjusting the display position

To adjust the display position

1. Stand at the front side of the panel and take the panel at both sides.

2. Very important: Tilt the panel upwards before changing the orientation.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

9

3. Display installation

3. To change from portrait to landscape, turn the panel counterclockwise.

4. To change from landscape to portrait, turn clockwise.

If, after installing the display o f the system, you change the panel orientation while an
image is on the screen, the result depends on the graphic board and the resolution of
the image. In some cases the image will be rotated automatically, in other cases it will
not be rotated (e.g., when pixels would be lost after rotat
image resolution in the display control pa nel and restart the system after changing the
orientation.

ion). If necessary , change the

3.3 Removing the connector compartment cover

To remove the connector compartment cover

1. Gently push the two lips on top of the cover

2. Pull the top of the cover slightly away from the display and lift the cover upwards.

10 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

3. Display installation

3.4 Connecting the signal cables

CAUTION: Only connect one of the two video links. Connecting both inputs simultane-

ously will result in driver errors.

To connect the signal cables to the display:

To get access to the connectors, remove the connector compartment cover. See "Removing the connector
compartment cover", page 10.

You may connect the display to a display controller by using the DVI or the DP connection. The input
selection of the device is automatically done. By default, the DisplayPort input has priority over the DVI
input. This can be changed in the OSD menu.

1. Connect the DVI or DP of the display controller to the DVI or DP connector of the display.

2. If you want to make use of the display’s USB upstream connector, connect a PC USB downstream

connector to the display’s USB upstream connector.

3. If you have chosen to use the display’s USB downstream connector, connect a USB device to the

downstream connector.

4. Connect the supplied external DC power supply to the +24 Vdc power input of the display.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

11

3. Display installation

5. Plug the mains connector of the external DC power supply to a grounded power outlet by means of

one of the supplied power cables.

3.5 Routing the cables & Reattach the connector compartment
cover

To route the cables

1. Route all connected cables through the cable routing channel in the stand of your display.

Tip: The cable straps at the inside of the connector compartment allow you to fix the cables for better

shielding of the cables.

To R eattach the connector compartment cover

1. Reattach the connector compartment cover by sliding the cover’s bottom in position and then push the

cover’s top. You’ll hear a “click” sound of the cover’s clips when the connector compartment cover is
in position.

12

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

3.6 VESA-mount installation

WARNING: Never move a display attached to an arm by pulling or pushing the display

itself. Instead, make sure that the arm is equipped with a VESA approved handle and
use this to move the display.

3. Display installation

Please refer to the instruction manual of the arm for more information and instructions.

WARNING: Use an arm that is approved by VESA (according to the VESA 100 mm stan-

dard).

Use an arm that can support the weight of the display. Refer to the technical specifica­tions of this display for the applicable weight.

Overview

The panel, standard attached to the tilt & swivel foot, is compatible with the VESA 100 mm standard. So
itcanbeusedwithanarmstandaccordingtotheVESA100mmstandard.

Therefore, the tilt & swivel foot must be remove

1. Fasten the height mechanism of the foot by putting the red clip in the hole "Unlocking the height mech-

anism", page 9 .

d from the panel.

2. Put the display face down on a clean and soft surface. Be careful not to damage the panel screen.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

13

3. Display installation

3. Remove the plastic cover with a flathead screw driver.

4. Slide the plastic cover over the neck of the foot.

5. Remove the four screws fixing the foot while supporting the foot.

6. Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm.

3.7 First time starting up

Overview

You are now ready to start up your Coron

1. Switch on your Coronis 5MP LED Display as described in "Standby switching", page 16.

2. Turn on the computer connected to your display.

If you have properly installed your display and display controller, the Windows start-up messages will
appear once the boot procedure is finished.

is 5MP LED Display for the first time.

Your Coronis 5MP LED Display will be running in a basic video mode at a default refresh
rate when first time starting up. If you are using a Barco display controller, please con­sult the user guide delivered with it to install the drivers, software and documentation.
When this is done, your display will automatically detect the connected video input sig­nal(s) and apply the correct video mode and refresh rate.

14 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

4. Daily operation

4. DAILY OPERATION

4.1 Recommendations for d aily operation

Optimize the lifetime of your display

Enabling the Display Power Management System (DPMS) of your display will optimize its diagnostic life­time by automatically switching off the backlight when the display is not used for a specified period of time.
By default, DPMS is enabled on your display, but it also needs to be activated on your workstation. To do
this, go to “Power Options Properties” in the “Control Panel”.

Barco recommends setting DPMS activation after 20 minutes of non-usage.

Use a screen saver to avoid image retention

Prolonged operation of an LCD with the same content on the same screen area may result in a form of
image retention.

You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver. You
can activate a screen saver in the “Display properties” window of your workstation.

Barco recommends setting screen saver activation after 5 minutes of non-usage. A
good screen saver displays moving content.

In case you are working with the same image or an application with static image elements for several hours
continuously (so that the screen saver is not activated), change the image content regularly to avoid image
retention of the static elements.

Understand pixel technology

LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a
limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic
performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its
LCD panels.

To learn more about LCD technology and missing pixels, consult the dedicated white
papers available at w

ww.barco.com/healthcare.

Enhance user comfort

Every Barco multi-head display system is color matched with the highest specifications in the market.

Barco recommends keeping color-matched displays together. Furthermore, it is impor­tant to use all displays of a multi-head configuration at the same rate to preserve color
matching throughout the economic lifetime of the system.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 15

4. Daily operation

Maximize quality assurance

The ’MediCal QAWeb’ system offers online service for high-grade Quality Assurance, providing maximum
diagnostic confi dence and uptime.

Barco recommends to install MediCal QAWeb Agent and apply the default QAWeb policy
at least. This policy includes calibration on regular intervals. Connecting to MediCal
QAWeb Server offers even more possibilities.

Learn more and sign up for the free MediCal QAWeb Essential level at

w

ww.barco.com/healthcare/qa.

4.2 Key indicator lights

About the key indicator lights

By default, the indicator lights of the keys will be dimmed which makes the keys unavailable at that mo­ment. To make the keys illuminate and available for further actions touch one of the keys. As a result, all
keys will be illuminated and are now available for further actions. However, if no further actions are taken
within the following 5 seconds, the keys will dim again.

The I-Luminate/Left key is always lit and available for activation of t
ture. Please refer to "I-Luminate", page 18 for more information.

The key auto-dim function can be disabled in the OSD menus. Please refer to "Key in­dicator lights", page 20 f or detailed instructions on how to do this.

4.3 Standby switching

About standby switching

The connected power supply also provides a switch that can be used to turn the power
completely off. To use the display, please make sure to switch on this power supply.
This can be done by pushing the on/off switch on the power supply into the “│” position.

Switching on the display while it is in standby mode or vice versa can be done by:

1. Illuminate the keys as previously described.

2. While the keys are illuminated, touch the stan

dby key (right button) for approximately 2 seconds.

he I-Luminate fea-

As a result, the display will switch on or will switch to standby mode. When the display is switched on,
the power LED is white. When the display is in standby mode, the power LED is orange.

The power LED can be disabled in the OSD menus. Please refer to "Power status indi­cator light", page 19 for detailed instructions on how to do this.

16 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

4. Daily operation

In case of a power outage recovery, your display will always start-up in the power mode
it was in before the power interruption (i.e. standby or on). This protects your display
against inadvertent image retention problems.

4.4 Bringing up the OSD menus

How to bring up the OSD menus

TheOSDmenuallowsyoutoconfigure different settings to make your Coronis 5MP LED Display fityour
needs within your working environment. Also, you can retrieve general information about your display and
its current configuration settings through the OSD menu.

Bringing up the OSD menus can be done by:

1. If not already done so, switch on the display as previously described.

2. Illuminate the keys as previously described.

3. While the keys are illuminated, touch the menu key.

As a result, the OSD main menu comes up in the bottom right corner of the screen. However, if no further
actions are taken within the following 90 seconds, the OSD will disappear agai

n.

The OSD menu auto-exit function can be disabled in the OSD menu. Please refer to
"OSD menu automatic close function", page 19 for detailed instructions on how to do
this.

4.5 Navigating through the OSD menus

How to navigate through the OSD menus

Navigating through the OSD menus can be done by:

• Use the left/right keys to move through the (sub)menus, change values or make selections.

• To go into a submenu or confirm adjustments and selections

• Use the standby key to cancel adjustments or exit a (sub)menu.

• Exit all OSD menus at once by touching the standby key for approximately 2 seconds.

The key icons are displayed above the keys, adapte
(menu dependent).

I-Luminate is not available while the OSD menu is activated.

, use the menu key.

d to the function that it is used for

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 17

4. Daily operation

Overview key icons

4.6 I-Luminate

Left, Right

Menu

Enter

Cancel

Standby (IEC 60417–5009)

About I-Luminate

When the display is in power on mode and the OSD menu is not shown, I-Luminate can be activated by
touching the I-luminate/left key.

Unlike other Barco products, especially designed for tomography, in the MDCG-5221, I-Luminate supports
one mode: Full-screen luminance boost.

When touching the I-Luminate key, the display will enter the I-Luminate mode, for approximately 1 minute.
Touch the I-Luminate key again to immediately switch back to normal mode.

18

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

5. Advanced operation

5. ADVANCED OPERATION

5.1 OSD menu language

About the OSD menu language

By default, the OSD menu comes up in English. However, there’s a wide range of other languages avail­able for the OSD menu of your Coronis 5MP LED Display.

To change the language of the OSD menu:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > User Interface > Menu menu.

3. Enter the Language submenu.

4. Select one of the available languages and confirm.

5.2 OSD menu automatic close function

About the OSD menu automatic close function

By default, the OSD menu will disappear automatically after approximat
ever, this function can be disabled so that the OSD menu remains on the screen until manually closed.

ely 90 seconds of inactivity. How-

To enable/disable the OSD menu automatic close function:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > User Interface > Menu menu.

3. Enter the Automatic Close submenu.

4. Select Enabled/Disabled as desired and confirm.

5.3 Power status indicator ligh t

About the power status indicator light

By default, when the display is switched on, the power status indicator light is dimmed. This behavior can
be changed so that the power status indicator light will be blue when the display is switched on.

When the display is in stand-by mode, the power status indicator light will always turn
orange, even when the power status indicator light is disabled.

To enable/disable the power status indicator light:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > User Interface > Indicator Lights menu.

3. Enter the Power Status submenu.

4. Select Enabled/Disabled as desired and confirm.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

19

5. Advanced operation

5.4 Key indicator lights

About the key indicator lights

By default, after lighting up, the key indicator lights will dim again if no further actions are taken within the
following 5 seconds. However, this behavior can be changed so that the key indicator lights are always
on or always off.

To configure the key indicator lights

1. Bring up the OSD main menu.

2. Navigate to the Configuration > User Interface > Indicator Lights menu.

3. Enter the Keys submenu.

4. Select Automatic/Always On/Always Off as desired and confirm.

The I-Luminate key is always lit and cannot be turned off.

5.5 Power lock function

About the power lock function

By enabling the power lock function, the Coronis 5MP LED Display is forced to remain switched on. This
means that it can’t be switched to stand-by mode manually until the power lock function is disabled again.

To enable/disable the power lock function:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > User Interface > Controls menu.

3. Enter the Power Lock submenu.

4. Select Enabled/Disabled as desired and confirm.

5.6 Ethernet over USB

About Eth. over USB

By default, the Ethernet over USB will be disabled. This does not disable the USB hub and still allows
to make use of the display’s USB downstream connectors and any external devices connected to it (key­board,mouse,...).

Please note that a connection from a PC USB downstream connector to the display’s USB upstream
connector is required to be able to use this functionality.

By enabling the Ethernet over USB, you allow the internal Coronis 5MP LED Display processor to com­municate directly over USB with the connected PC.

Enabling the Ethernet over USB is only recommended when you are using a non-Barco
display controller. If you are using a Barco displ
automatically be done over the connected video cable(s).

20 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

ay controller, this communication will

5. Advanced operation

To enable/disable the eth. over USB:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Connectivity menu.

3. Enter the Eth. over USB submenu.

4. Select Enabled/Disabled as desired and confirm.

5.7 USB

About USB

By default, USB will be enabled. This will allow the connected PC to communicate directly over USB with
the internal Coronis 5MP LED Display processor.

By disabling USB, communication between the internal Coronis 5MP LED Display processor and the con­nected PC will not be possible. This does not disable the USB hub and still allows to make use of the
display’s USB downstream connectors and any external devices connected to it (keyboard, mouse, ...).

Please note that a connection from a PC USB downstream connector to the display’s USB upstream
connector is required to be able to use this functionality.

Enabling the USB endpoint is only recommended when you are using a non-Barco dis­play controller. If you are using a Barco display controller, this communication will au­tomatically be done over the connected video cable(s).

To enable/disable USB:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Connectivity menu.

3. Enter the USB submenu.

4. Select Enabled/Disabled as desired and confirm.

5.8 DPMS mode

About DPMS mode

Enabling the Display Power Management System (DPMS) mode on your display will optimize its diagnos­tic lifetime by automatically switching off the backlight when the display is not used for a specified period
of time. By default, DPMS mode is enabled on your display, but it also needs to be activated on your
workstation. To do this, go to the “Power options properties” window of your workstation.

Barco recommends setting DPMS activation after 20 minutes of non-usage.

When DPMS mode is enabled on your display, an additional OSD power saving function
becomes available: hibernate. Please refer to "Hibernate", page 22 for more information
on hibernation and how to enable this function.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 21

5. Advanced operation

To enable/disable DPMS mode on your display:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Power Management menu.

3. Enter the DPMS Mode submenu.

4. Select Enabled/Disabled as desired and confirm.

5.9 Hibernate

About hibernate

Enabling hibernation will not only switch off the backlight but will also force the display to disable other
functionalities so that power consumption is further reduced to a minimum. This happens after a specific
period of time which can be manually adjusted.

Hibernate can only be enabled on your display when the DPMS mode is enabled first.
Therefore, please refer to "DPMS mode", pa ge 21 to do this.

To enable/disable hibernation on your display:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Power Management menu.

3. Enter the Hibernate submenu.

4. Select Enabled/Disabled as desired and confirm.

To specify the hibernate timeout:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Power Management menu.

3. Enter the Hibernate Timeout submenu.

4. Set the timeout value as desired and confirm.

5.10 I-Luminate default mode

About the I-Luminate default mode

The I-Luminate default mode defines the default activated mode during the I-Luminate boost. This mode
is:

Screen The boost mode is applied on the screen display.

To enable/disable I-Luminate:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > I-Luminate menu.

3. Enter the Default mode submenu.

4. Select Enabled / Disabled as desired and confirm.

22

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

5. Advanced operation

5.11 Luminance target

About the luminance target

The luminance target of your Coronis 5MP LED Display is adjustable over a predefined range. When you
change the luminance target, the display will adjust its backlight to reach the target.

To set the luminance target:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration menu.

3. Enter the Luminance Target submenu.

4. Set a luminance target value as desired and confirm.

The default, factory DICOM calibrated luminance value is available in the technical spec­ifications table. The guaranteed backlight lifetime is valid for this setting.

5.12 Viewing mo des

About viewing modes

The Coronis 5MP LED Display can be used in two viewing modes:

Diagnostic This mode provides the full calibrated luminance

and is intended for using the display for diagnostic
purposes.

Text In this mode, the luminance is reduced to

approximately half of the luminance. This
is intended for using the display with office
applications such as word processing.

Please note that text mode is not persistent, once
powered off, the unit will restart in diagnostic mode.

To quickly switch the viewing mode without having to enter the OSD menu, touch the
left and right key (the two leftmost buttons) at the same time during normal operation.

As the Coronis 5MP LED Display is intended to be used in a diagnostic environment,
the diagnostic mode should always be selected.

To select a viewing mode:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration menu.

3. Enter the Viewing Mode submenu.

4. Select Diagnostic/Text as desired and confirm.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

23

5. Advanced operation

5.13 Display functions

About display functions

Native, uncorrected panels will display all grayscale/color levels with luminance increments that are not
optimal for crucial diagnostic information. Studies have shown however, that in medical images certain
grayscale/color parts contain more diagnostic information then others. To respond to these conclusions,
display functions have been defined. These functions emphasize on these parts containing crucial diag­nostic information by correcting the native panel behavior.

Native

Dynamic Gamma 1.8

Dynamic Gamma 2.2

DICOM DICOM (Digital Imaging and Communications

User

Gamma 1.8

Gamma 2.2

If you select Native, the native panel behavior will
not be corrected.

These are gamma functions that are shifted to take
into account the non-zero luminance of an LCD
panel when driven with a “black” signal. They are
especially useful in CT applications to improve the
perception of low Hounsfield values.

in Medicine) is an international standard that
was developed to improve the quality and
communication of digital images in radiology.
In short, the DICOM display function results in
more visible grayscales in the images. Barco
recommends selecting the DICOM display function
for most medical viewing applications.
This display function will be automatically selected
when display functions are defined by MediCal
QAWeb.

Select one of these display functions in case the
display is to replace a CRT display with a gamma
of 1.8 or 2.2 respectively .

To select a display function:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration menu.

3. Enter the Display Function submenu.

4. Select one of the available display functions and confirm.

5.14 A mbient Light Compensation (ALC)

About ALC

Ambient Light Compensation (ALC) can only be enabled on your display when the DI­COM display function is selected. Therefore, please refer to "Display functions", page
24 to correctly set the display function.

When ALC is enabled, the DICOM display function will be recalculated taking a preset ambient light cor­rection value into account. This value is determined by the selected reading room. Therefore, it is also
important to select a realistic reading room when enabling ALC. This can be done by following the instruc­tions in "Reading rooms", page 25.

To enable/disable ALC:

1. Bring up the OSD main menu.

24

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

2. Navigate to the Configuration > Calibration > Ambient Light menu.

3. Enter the Ambient Light Compensation submenu.

4. Select Enabled/Disabled as desired and confirm.

5.15 Reading rooms

About reading rooms

Reading rooms can only be selected w hen the DICOM display function is selected.
Therefore, please refer to "Display functions", page 24 to correctly set the display
function.

5. Advanced operation

The American Association of Physicists in Medicine (AAPM) composed a list of pre-defined reading rooms
Each of these reading rooms are defined by following parameters:

• the maximum light allowed in this type of room

• the preset ambient light correction value for this reading room

These parameters are stored in your display and determine the preset ambient light correction value to
take into account to recalculate the DICOM display function when Ambient Light Compensation (ALC) is
enabled. Please refer to "Ambient Light Compensation (ALC)", page 24 to enable ALC.

The available reading rooms for your Coronis 5MP LED Display are:

CR/DR/ MAMMO Corresponds to light conditions in diagnostic

reading rooms for computed radiology, digital
radiology or mammography. This setting has the
lowest maximum ambient light.

CT/MR/NM Corresponds to light conditions in diagnostic

reading rooms for computed tomography, magnetic
resonance or nuclear medicine scans.

Staff Office Corresponds to light conditions in office rooms.

Clinical Viewing Room Corresponds to light conditions in diagnostic

reading rooms for clinical viewing.

Emergency Room

Operating Room Corresponds to light conditions in operating rooms.

Corresponds to light conditions in emergency
rooms.

This setting has the highest maximum ambient light.

.

To select a reading room:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Ambient Light menu.

3. Enter the Reading Room submenu.

4. Select one of the available reading rooms and confirm.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

25

5. Advanced operation

5.16 Continuous ALC

About Con tinuous ALC

Continuous ALC can only be selected when the DICOM display function is selected.
Therefore, please refer to "Display functions", page 24 to correctly set the display func­tion.

Enabling continuous ALC will continuously recalculate the DICOM display function taking the averaged
ambient light into account.

To select continuous ALC:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Ambient Light menu.

3. Enter the Continuous ALC submenu.

4. Select Enabled/Disabled as desired and confirm.

5.17 Embedded QA

Overview

• About Embedded QA

• DICOM status report

• DICOM compliance check

• DICOM calibration

• Reset DICOM calibration

• DICOM error threshold

5.17.1 About Embedded QA

About

Embedded QA allows you to run a display calibration or compliance test directly from the display using the
OSD menus described in the next sections. Embedded QA will use the front sensor / I-Guard to measure
the necessary luminance levels for either a calibration or compliance test. Various settings for both actions
can be selected from the display’s OSD menu. The last results of both actions can be consulted from the
OSD.

Embedded QA or MediCal QAWeb?

Embedded QA is not a replacement for the Barco MediCal QAWeb sol

Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still
highly recommends MediCal QAWeb as the solution of choice for calibration and QA. Medical QAWeb
brings many benefits such as centralized asset management, the ability to schedule tasks, remote man­agement, automated reporting, alerting and specific support of regional QA standards such as DIN 6868­57, JESRA and AAPM TG18. That’s why MediCal QAWeb Agent acts as the master for all supported dis­plays from the moment it is installed and running. MediCal QAWeb Agent will take over from Embedded
QA and overwrite any settings which were applied by Embedded QA.

ution.

26

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

5.17.2 DICOM status report

About DICOM status report

Following information is available:

5. Advanced operation

DICOM Compliance Status (status
since last compliance check)

DICOM Calibration Status

Current DICOM Settings

Compliance status Shows if the current DICOM curve

is compliant or not.

Maximum error

Error threshold

Time elapsed since latest
compliance check
Display Function

Ambient light compensation

Reading Room

Luminance

Black luminance

No calibration executed yet.

Calibration executed.

Display function Shows the current display

Ambient Light Compensation Shows the ambient light

Reading room

Shows the maximum error of the
current DICOM curve. This is the
deviation compared to a perfect
DICOM.

Shows the error threshold. This is
the maximum error allowed before
a DICOM calibration is required.
Shows the backlight runtime since
last compliance check.
Shows the current display
function.

Shows the ambient light
compensation status.
Shows the selected reading room.

Shows the measured luminance.

Shows the measured backlight
luminance.

No other information is visible

When the calibration is executed,
the following extra information
is shown: Backlight runtime
elapsed since latest calibration,
display function, ambient light
compensation, reading room.

function.

compensation status.
Shows the selected reading room.

To retrieve the DICOM status report:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Embedded QA menu.

3. Select DICOM status report to make the information visible on the screen.

5.17.3 DICOM compliance check

About DICOM compliance check

The DICOM compliance check will measure the DICOM curve of your display in different steps. After
measurement, the DICOM status report is shown.

To start DICOM compliance check:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Embedded QA menu.

3. Select DICOM compliance check to start the compliance check.

Warning:Pressing a key during the compliance check will abort the check.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

27

5. Advanced operation

5.17.4 DICOM calibration

About DICOM calibration

TheDICOMcalibrationwilladdacorrectiontothecurrentDICOMcurvetoapproachtheperfectDICOM
curve as good as possible.

To start DICOM calibration:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Embedded QA menu.

3. Select DICOM calibration to start the calibration.

Warning:Pressing a key during calibration will abort the calibration, previous values will be restored.

Note: After calibration, the compliance check will start automatically.

5.17.5 Reset DICOM calibration

About reset DICOM calibration

It is possible to restore the original (not corrected) DICOM curve.

To reset the DICOM calibration:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Embedded QA menu.

3. Enter the DICOM preferences submenu.

4. Select reset DICOM calibration to restore the original (not corrected) DICOM curve.

5.17.6 DICOM error threshold

About DICOM error threshold

The threshold to definetheDICOMcompliancecanbemodified in steps of 5% starting from 5 to 30%.
When the maximum deviation is not bigger than the selected threshold, the compliance check will be OK.

To set the DICOM error threshold:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Calibration > Embedded QA menu.

3. Enter the DICOM preferences submenu.

4. Set DICOM error threshold as desired and confirm.

5.18 Image scaling

About image scaling

Enabling image scaling will multiply each individual pixel to one or more adjacent pixels so that the size
of the displayed image will be a multiple of the original image source video input signal.

Image scaling is only possible when the resolution of y o
is less than or equal to half the maximum resolution of the display.

28 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

ur display’s video input signal

5. Advanced operation

To enable/disable image scaling:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Image Source menu.

3. Enter the Scaling submenu.

4. Select Enabled/Disabled as desired and confirm.

5.19 Display o rientatio n

About Display orientation

Your display automatically detects its physical orientation (portrait or landscape) and, by default, automat­ically adjusts the image orientation to this. This means that when your display is physically rotated, the
image will rotate along.

The OSD menu however, allows to overrule this behavior and force the image orientation to portrait or
landscape regardless of the physical orientation of the display. This may be especially useful when oper­ating your display with the screen facing upwards.

To set the Display orientation

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Image Sources menu.

3. Enter the Display Orientation submenu.

4. Select Landscape/Portrait/Automatic as desired and confirm.

5.20 Video input signals

About inp ut signals

The available input signals for your display are:

DisplayPort 1 The input corresponding to the DisplayPort

connector.

DVI 1 The input corresponding to the DVI connector.

Automatic Selection

To manually select a video input signal:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Image Source menu.

3. Enter the Input Signal submenu.

The input is automatically selected.

4. Select one of the available input signals and confirm.

5.21 Video encoding modes

About video encoding modes

Video encoding modes specify how the color and lu
In consumer displays, this is usually done by a limited 8-bit encoding mechanism. Your Coronis 5MP
LED Display however, features 10-bit encoding enabling it to better match the DICOM defined grayscale

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

minance information is encoded in the video signal.

29

5. Advanced operation

range. Such an extensive range is necessary to comply with the guidelines set forward by the latest
medical guidelines.

The available video encoding modes for your display are listed below.

Please note that the display controller connected to your display might not always sup­port all these video encoding modes.

Standard

HDR1

HDR2

Dual 10 (only with Barco display controller) Dual 10 is a Barco specific 10-bit video encoding

Automatic When selecting this option, your Coronis 5MP LED

This mode uses the standard 8 bit encoding
mechanism.

This mode features 10-bit video encoding following
the High Dynamic Range (HDR) standard, usually
used on color displays.
HDR2 is a Barco specific mode featuring 10-bit
video encoding following the High Dynamic Range
(HDR) standard but allowing full refresh rate (which
is not always possible with HDR1). This mode is
usually used on color displays.

mode which is usually used on grayscale displays
and which allows full refresh rate.

Display will automatically assign the correct video
encoding settings to the connected video input
signals.

To manually select a video encoding mode:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Image Source menu.

3. Enter the Video Encoding submenu.

4. Select one of the available video encoding modes and confirm.

5.22 Grayscale conversion modes

About grayscale conversion modes

Grayscale conversion modes specify how color generated on the display controller is converted to
grayscale in your display.

The available grayscale conversion modes are:

No Conversion

Use Red Channel This mode is intended for grayscale displays where

gray is sent over the red channel.

Use Green Channel This mode is intended for grayscale displays where

gray is sent over the green channel.

Use Blue Channel This mode is intended for grayscale displays where

gray is sent over the blue channel.

Use All Channels This mode is intended for grayscale displays where

gray is sent over the red, green and blue channel.
This is done by means of a standard conversion
mechanism where 30% red, 59% green and 11%
blue are used to generate gray.

30 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

5. Advanced operation

To manually select a grayscale conversion mode:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Image Source menu.

3. Enter the Grayscale Conversion submenu.

4. Select one of the available color conversion modes and confirm.

5.23 EDID timings

About EDID timings

Following EDID timings are available for your Coronis 5MP LED Display:

Refresh Rate Allows to manually select the refresh rate of the

image source video input signal depending on the
maximum refresh rate of the display controller
connected to your display.

Preferred Orientation Allows to change the orientation of the image

source video input signal to landscape, portrait or
to let the display automatically assign the correct
orientation.

Color Depth

Allows to change the color depth to 8 or to 10 bit.

To manually set EDID timings:

1. Bring up the OSD main menu.

2. Navigate to the Configuration > Image Source menu.

3. Enter the Timings submenu.

4. Select Refresh Rate, Preferred Orientation or Color Depth.

5. Select one of the available settings and confirm.

5.24 Display info

About display info

Your display serial number, color type, native resolution, firmware versions, etc. are available in a dedi­cated submenu of the OSD menu.

To retrieve info about your display:

1. Bring up the OSD main menu.

2. Navigate to the About this Display menu to make the information visible on the screen.

5.25 Display status

About d isplay status

The Status submenu of the OSD menu provides info on the current status of your display (runtimes, tem­peratures, etc.), the status of the connected image sources (video encoding mode, timings, etc.), the
current calibration status of your display (display function, luminance, ALC, etc.) and the status about
activated connections.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

31

5. Advanced operation

To retrieve the status of your display:

1. Bring up the OSD main menu.

2. Navigate to the Status menu.

3. Enter the Display, Image Sources, Calibration or Connectivity submenu as desired.

32

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

6. Repackaging instructions

6. REPA CKAGING INSTRUCTIONS

WARNING: Before repacking the display, follow the instruction to replace the protection

buffer to prevent damage to the display.

Overview of the packaging

10

9

8

7

6

5

4

3

2

1

Image 6-1
Packaging

Box

1

Bottom buffer

2

Left protection buffer

6

Display controller box buffer

7

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

33

6. Repackaging instructions

Foot protection buffer

3

Right protection buffer

4

Accessory box buffer

8

Accessory box (Power supply,

9

cables)

5

Display

Display controller box

10

6.1 Replacing the protection buffer

How to replace the protection buffer

1. Place the display on a stable surface.

2. Put the display in the lowest position and fasten the height mechanism, see "Unlocking the height mech-

anism", page 9 .

3. Very important: Tilt the panel away from the foot before changing the orientation.

4. Turn the panel counterclockwise to put the panel in landscape orientation, see "Adjusting the display

position", page 9 .

5. Place the connector compartment cover in the protection buffer.

6. Slide the protection buffer over the foot of the display.

7. Tilt the panel back to the foot.

Image 6-2
Placing the protection buffer.

34 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

7. Cleaning your display

7. CLEANING YOUR DISPLAY

7.1 Cleaning instructions

To clean the display

Clean the display using a sponge, cleaning cloth or soft tissue, lightly moistened with a recognized clean­ing product for medical equipment. Read and follow all label instructions on the cleaning product. In case
of doubt about a certain cleaning product, use plain water.

Do not use following products:

• Alcohol/solvents at higher concentration > 5%

• Strong alkalis lye, strong solvents

•Acid

• Detergents with fluoride

• Detergents with ammonia

• Detergents with abrasives

• Steel wool

• Sponge with abrasives

• Steel blades

• Cloth with steel thread

CAUTION: Take care not to da mage or scratch the front glass or LCD. Be careful with

rings or other jewelry and do not apply excessive pressure on the front glass or LCD.

CAUTION: Do not apply or spray liquid directly to the display as excess liquid may cause

damage to internal electronics. Instead, apply the liquid to a cleaning cloth.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 35

7. Cleaning your display

36 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

8. IMPORTANT INFORMATION

8.1 Safety information

General recommendations

Read the safety and operating instructions before operating the device.

Retain safety and operating instructions for future reference.

Adhere to all warnings on the device and in the operating instructions manual.

Follow all instructions for operation and use.

Electrical Shock or Fire Hazard

To prevent electric shock or fire hazard, do not remove cover.

No serviceable parts inside. Refer servicing to qualified personnel.

Do not expose this apparatus to rain or moisture.

8. Important information

Modifications to the unit:

Do not modify this equipment without authorization of the manufacturer.

Type of protection (electrical):

Display with external power supply: Class I equipment.

Degree of safety (flammable anesthetic mixture):

Equipment not suitable for use in the presence of a flammable anesthetic mixture
or nitrous oxide.

with air or with oxygen

Non-patient care equipment

• Equipment primarily for use in a health care facility that is i

is unlikely (no applied part).

• The equipment may not be used with life support equipment.

• The user should not touch the equipment, nor its signal input por

and the patient at the same time.

Power connection – Equipment with external 24 VDC power suppl

• Power requirements: The equipment must be powered using the d

(

) SELV power supply.

• The medical approved DC (

• The power supply is specified as a part of the ME equipme

system.

• To avoid the risk of electric shock, this equipment must only be connected to a supply mains with

protective earth.

• The equipment should be installed near an easily accessible outlet.

• The equipment is intended for continuous operation.

) power supply must be powered by the AC mains voltage.

ntended for use where contact with a patient

ts (SIP)/signal output ports (SOP)

y

elivered medical approved 24 VDC

nt or combination is specified as a ME

Transient over-voltage

If the device is not used for a long time, disconnect it from the AC inlet to avoid damage by transient
over-voltage.

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

37

8. Important information

To fully disengage the power to the device, please disconnect the power cord from the AC inlet.

Power cords:

• Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent, 18 AWG min., rated 250 V

min., provided with a hospital-grade type plug 5-15P configuration for 120V application, or 6-15P for
240V application.

• Do not overload wall outlets and extension cords as this may result in fire or electric shock.

• Mains lead protection (U.S.: Power cord): Power cords should be routed so that they are not likely to

be walked upon or pinched by items placed upon or against them, paying particular attention to cords
at plugs and receptacles.

• The power supply cord should be replaced by the designated operator only at all time.

• Use a power cord that matches the voltage of the power outlet, which has been approved and complies

with the safety standard of your particular country.

Water and moisture

Never expose the display to rain or moisture.

Never use the display near water - e.g. near a bathtub, washbasin, swimming pool, kitchen sink, laundry
tuborinawetbasement.

Ventilation

Do not cover or block any ventilation openings in the cover of the set. When installing the device in a
cupboard or another closed location, heed the necessary space between the set and the sides of the
cupboard.

Installation

Place the device on a flat, solid and stable surface that can support the weight o
use an unstable cart or stand, the device may fall, causing serious injury to a child or adult, and serious
damage to the device.

fatleast3devices. Ifyou

This apparatus conforms to:

CE0120 (MDD 93/42/EEC; A1:2007/47/EC class IIb product), CE - 2004/108/EC, CE - 93/42/EEC;
A1:2007/47/EC class II b, IEC 60950-1:2005 + A1:2009 (2ND EDITION), IEC 60601-1:2005 + A1:2012,
ANSI/AAMI ES 60601-1:2005 + C1:2009 + A1:2012, CAN/CSAC22.2 No. 60601-1-08:2008, DEMKO ­EN 60601-1:2006, EN 60601-1-2:2007, CCC - GB9254-2008 + GB4943.1-2011 + GB17625.1-2003, KC,
VCCI, FCC class B, ICES-001 Level B, FDA 510(k), RoHS

National Scandinavian Deviations for CL. 1.7.2:

Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan"

Norway: "Apparatet må tilkoples jordet stikkontakt"

Sweden: "Apparaten skall anslutas till jordat uttag"

8.2 Environmental information

Disposal Information

Waste Electrical and Electronic Equipment

This symbol on the product indicates that, under the European Directive 2012/19/EU governing
waste from electrical and electronic equipment, this product must not be disposed of with other municipal
waste. Please dispose of your waste equipment by handing it over to a designated collection point for the

38

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

8. Important information

recycling of waste electrical and electronic equipment. T o prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.

For more information about recycling of this product, please contact your local city office or your municipal
waste disposal service.

For details, please visit the Barco website at: h

ttp://www.barco.com/en/AboutBarco/weee

Turkey RoHS compliance

Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.

[Republic of Turkey: In conformity with the WEEE Regulation]

中国大陆 RoHS

Chinese Mainland RoHS

根据中国大陆《电子信息产品污染控制管理办法》（也称为中国大陆RoHS）， 以下部分列出了Barco产品
中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准：

“电子信息产品中有毒物质的限量要求”中。

According to the “China Administration on Control of Pollution Caused by Electronic Information Products”
(Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or
hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in
the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of
toxic substances in Electronic Information Products”.

零件项目(名称)

Component name

印制电路配件

有毒有害物质或元素

Hazardous substances and elements

铅

Pb

xooo oo

汞

Hg

镉

Cd

六价铬

Cr6+

多溴联苯

PBB

多溴二苯
醚

PBDE

Printed Circuit Assemblies

液晶面板

LCD panel
外接电(线)缆

External Cables

內部 线路

Internal wiring

金属外壳

Metal enclosure

塑胶外壳

Plastic enclosure
散热片(器)

Heatsinks

电源供应器

Power Supply Unit

风扇

Fan

文件说明书

Paper Manuals

xooo oo

xooo oo

oo oo oo

oo oo oo

oo oo oo

oo oo oo

xooo oo

oo oo oo

oo oo oo

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 39

8. Important information

零件项目(名称)

Component name

光盘说明书

CD manual
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下.

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for
this part is below the limit requirement in SJ/T11363-2006.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的
限量要求.

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous
materials used for this part is above the limit requirement in SJ/T11363-2006

在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子信息产品污染控制标识要求》标准
贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP标签（请参阅实例，徽标内部的编号使用于制
定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。

All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the
“Electronic Information Products Pollution Control Labeling Standard” of Chinese Mainland, marked with
the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses
(please refer to the photo) is based on the “Standard of Electronic Information Products Environmental
Friendly Use Period” of Chinese Mainland.

有毒有害物质或元素

Hazardous substances and elements

铅

Pb

oo oo oo

汞

Hg

镉

Cd

六价铬

Cr6+

多溴联苯

PBB

多溴二苯
醚

PBDE

10

ChinaEnergyLabel

按照中国 <<能源效率标识管理办法>>

In accordance with The Regulation of the
Implementation on China Energy Label

能源效率

Energy Efficiency (cd/W)

关闭状态能耗

Energy Consumption in off mode (W)

能源效率等级

Energy Efficiency Level

执行的能源效率国家标准编号

Code of National Standard applied

本显示器符合以下要求

This monitor is compliant with the following
requirements
>1.05

<0.5

1

GB 21520-2008

40 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

8. Important information

8.3 R egulatory compliance information

Indications for use

The Coronis 5MP LED Display (MDCG-5221) display is intended to be used in displaying and viewing
digital images, for review and analysis by trained medical practitioners. It is designed for radiology and
digital mammography applications. Caution (USA): Federal law restricts this device to sale by or on the
order of a physician. (Details & exemptions are in the Code of Federal Regulations Title 21, 801 Part D).

FCC class B

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference re­ceived, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

Canadian notice

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme à la norme NMB-001 du Canada.

8.4 EMC notice

General information

No specific requirement on the use of external cables or other accessories except power supply.

With the installation of the device, use only the delivered power supply or a spare part provided by the
legal manufacturer. Using another can result in a decrease of the immunity level of the device.

Electromagnetic emissions

The Coronis 5MP LED Display is intended for use in the electromagnetic environment specified below.
The customer or the user of the Coronis 5MP LED Display should assure that it is used in such an envi­ronment.

Emissions test

RF emissions

CISPR 11

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 41

Compliance

Group 1 The Coronis 5MP LED Display

Electromagnetic environment –
Guidance

uses RF energy only for its
internal function. Therefore,
its RF emissions are very low
and are not likely to cause any
interference in nearby electronic
equipment.

8. Important information

Emissions test

RF emissions

CISPR 11
Harmonic emissions

IEC 61000-3-2
Volta ge fluctuations/ flicker

emissions

IEC 61000-3-3

This Coronis 5MP LED Display complies with appropriate medical EMC standards on emissions to, and
interference from surrounding equipment. Operation is subject to the following two conditions: (1) th
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Interference can be determined by turning the equipment off and on.

If this equipment does cause harmful interference to, or suffer from harmful interference of, surrounding
equipment, the user is encouraged to try to correct the interference by one or more of the following mea
sures:

• Reorient or relocate the receiving antenna or equipment.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which t

• Consult the dealer or an experienced technician for help.

Compliance

Class B

Class D

Complies

Electromagnetic environment –
Guidance

The Coronis 5MP LED Display
is suitable for use in all
establishments, including
domestic establishments and
those directly connected to the
public low-voltage power supply
network that supplies buildings
used for domestic purposes.

he receiver is connected.

is

-

Electromagnetic immunity

The Coronis 5MP LED Display is intended for use in the electromagnetic environme
The customer or the user of the Coronis 5MP LED Display should assure that it is used in such an envi­ronment.

Immunity test

Electrostatic discharge
(ESD)

IEC 61000-4-2

Electrical fast
transient/burst

IEC 61000-4-4

Surge

IEC61000-4-5

IEC 60601

Test levels

± 6kV contact

±8kVair

± 2kV for power supply
lines

± 1kV for input/ output
lines

± 1 kV line(s) to line(s)

± 2 kV line(s) to earth

Compliance level

± 6kV contact

±8kVair

± 2kV for power supply
lines

± 1kV for input/ output
lines

± 1 kV line(s) to line(s)

±2kVline(s)toearth

Electromagnetic
environment –
guidance

Floors should be wood,
concrete or ceramic tile.
If floors are covered with
synthetic material, the
relative humidity should
be at least 30%

Mains power quality
should be that of a typical
commercial or hospital
environment

Mains power quality
should be that of a typical
commercial or hospital
environment

nt specified below.

42 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

8. Important information

Immunity test

Voltage dips, short
interruptions and voltage
variations on power
supply input lines

IEC 61000-4-11

Power frequency (50/60
Hz) magnetic field

IEC 61000-4-8

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

IEC 60601

Test levels

<5%U
U

T

40% U

1

(> 95% dip in

T

) for 0.5 cycle

(60%dipinUT)

T

for 5 cycles

70% U

(30%dipinUT)

T

for 25 cycles

<5%U
U

) for 5s

T

(>95% dip in

T

3A/m

3Vrms

150 kHz to 80 MHz

3V/m

80 MHz to 2.5 GHz

Compliance level

<5%U
U

) for 0.5 cycle

T

40% U

(> 95% dip in

T

(60% dip in UT)

T

for 5 cycles

70% U

(30% dip in UT)

T

for 25 cycles

<5%U
U

)for5s

T

Not applicable

(>95% dip in

T

2

3V

3V/m

Electromagnetic
environment –
guidance

Mains power quality
should by that of a typical
commercial or hospital
environment. If the user
of the Coronis 5MP
LED Display requires
continued operation
during power mains
interruptions, it is
recommended that
the Coronis 5MP LED
Display be powered from
an uninterruptible power
supply or a battery.
Power frequency
magnetic fields should
be at levels characteristic
of a typical location in
a typical commercial or
hospital environment.
Portable and mobile
RF communications
equipment should be
used no closer to any part
of the Coronis 5MP LED
Display, including cables,
than the recommended
separation distance
calculated from the
equation applicable
to the frequency
of the transmitter.
Recommended
separation distance

d=1.2√P
d=1.2√P 80 MHz to 800

MHz
d=2.3√P 800 MHz to 2.5

Ghz

Where P is the maximum
output power rating
of the transmitter in
watts (W) according
to the transmitter
manufacturer and d
is the recommended
separation distance in
meters (m).

Field strengths from
fixed RF transmitters,
as determined by an
electromagnetic site

1. is the a.c. mains voltage prior to application of the test level.

2. Coronis 5MP LED Display doesn’t contain susceptible components to magnetic fields

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 43

8. Important information

Immunity test

At 80 MHz and 800 MHz, the higher frequency range applies.

These guidelines may not apply in all situations. Electromagnetic propagation is af­fected by absorption and reflection from structures, objects and people.

IEC 60601

Test levels

Compliance level

Electromagnetic
environment –
guidance

survey,3should be less
than the compliance
level in each frequency

4

range.

Interference may occur in
the vicinity of equipment
marked with symbol:

Recommended separation distance

The Coronis 5MP LED Display is intended for use in an electromagnetic environment in which radiated
RF disturbances are controlled. The customer of the user of the Coronis 5MP LED Display can help
prevent electromagnetic interference by maintaining a minimum distance between portable and mobile
RF communications equipment (transmitters) and the Coronis 5MP LED Display as recommended below,
according to the maximum output power of the communications equipment.

Rated maximum output
power of transmitter

W

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100121223

At 80 M Hz and 800 MHz, the separation distance for the higher frequency range applies .

Separation distance according to frequency of transmitter

5

150kHz to 80MHz
d=1.2√P

80MHz to 800MHz
d=1.2√P

800MHz to 2.5GHz
d=2.3√P

3. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur
radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the
location in which the Coronis 5MP LED Display is used exceeds the applicable RF compliance level above, the Coronis 5MP LED
Display should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary,
such as re-orienting or relocating the Coronis 5MP LED Display.

4. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than3V/m.

5. For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be
estimated using the equation applicable to the frequency of the transmitter. Where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.

44 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

These guidelines may not apply in all situations. Electromagnetic propagation is af­fected by absorption and reflection form structures, object and people.

8.5 Explanation of symbols

Symbols on the device

On the device or power supply, you may find the following symbols (nonrestrictive list):

Indicates compliance with the Directive 93/42/EEC as Class I device

Indicates compliance with the Directive 93/42/EEC as Class II device

8. Important information

Indicates compliance with Part 15 of the FCC rules (Class A or Class B)

Indicates the device is approved according to the UL regulations

Indicates the device is approved according to the UL regulations for Canada
and US

Indicates the device is approved according to the UL Demko regulations

Indicates the device is approved according to the CCC regulations

Indicates the device is approved according to the VCCI regulations

Indicates the device is approved according to the KC regulations

Indicates the device is ap

Indicates the device is approved according to the PSE regulations

Indicates the USB co

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014 45

proved according to the BSMI regulations

nnectors on the device

8. Important information

Indicates the DisplayPort connectors on the device

Indicates the manufacturing date

Indicates the temperature limitations6for the device to safely operate within specs

Indicates the device serial no.

Warning: dangerous voltage

Caution

Consult the operating instructions

Indicates this device must not be thrown in the trash but must be recycled,
according to the European WEEE (Waste Electrical and Electronic Equipment)
directive

Indicates Direct Current (DC)

Indicates Alternating Current (AC)

Stand-by

Equipotentiality

Symbols on the box

On the box of the device, you may find the following symbols (nonrestrictive list):

Indicates a medical device that can be broken
or damaged if not handled ca
stored.

Indicates a medical devic
protected from moisture when being stored.

Indicates the storage
must be transported, handled and stored in such a
way that the arrows always point upwards.

6. Values for xx and yy can be found in the technical specifications paragraph.

46 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

direction of the box. The box

refully when being

e that needs to be

8. Important information

15

n

20 - 30 Kg

-20 °C

x

5 %

xx

50 kPa

Indicates the maximum number of boxes to be
stacked on each other.

Indicates that the box should be carried with two
persons.

Indicates that the box should not be cut with a
knife, a cutter or any other sharp object.

Indicates the temperature limits to which the

yy

+60 °C

xx

yy

85 %

medical device can be safely exposed when being
stored.

Indicates the range of humidity to which the
medical device can be safely exposed when being
stored.

yyy

106 kPa

Indicates the range of atmospheric pressure to
which the medical device can be safely exposed
when being stored.

8.6 Legal disclaimer

Disclaimer notice

Although every attempt has been made to achieve technical accuracy in this document, we assume no
responsibility for errors that may be found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.

Barco software products are the property of Barco. They are distributed under copyright by Barco N.V. or
Barco, Inc., for use only under the specific terms of a software license agreement between Barco N.V. or
Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any
form, is authorized.

The specifications of Barco products are subject to change without notice.

Trademarks

All trademarks and registered trademarks are property of their respective owners.

Copyright notice

This document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may
be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems - without written permission of Barco.

© 2014 Barco N.V. All rights reser

Patent information

ved.

This product is covered under the following intellectual property rights:

US Patent RE43,707

US Patent 7,038,186

US Patent 7,166,829

US Patent 6,950,098

European Patent 1 274 066

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

47

8. Important information

European Patent 1 915 875

8.7 Technical specifications

MDCG-5221

Product acronym

Screen technology a-si TFT active matrix dual domain IPS

Active screen size (diagonal) 540 mm (21.3”)

Active screen size (H x V) 422.4 mm x 337.9 mm (16.5 x 13.3“)

Aspect ratio (H:V)

Resolution

Pixel pitch 0,165

Color imaging

Gray imaging

Number of grayscales (LUT
in/LUT out)
Viewing angle (H, V) 170°

MDCG-5221

5:4

5 MP (2560 x 2048)

No

Yes

1024 gray levels (10/12)

Uniform Luminance
Techn o l o g y (ULT )
Per Pixel Uniformity (PPU)

Ambient Light Compensation
(ALC)
Backlight Output Stabilization
(BLOS)
I-Guard

Maximum luminance

DICOM calibrated luminance
(ULT off)
Contrast ratio (ULT off)

Responsetime(Tr+Tf)

Scanning frequency (H; V)

Housing color

Video input signals

Video inout terminals NA

USB ports

USB standard

Power requirements (nominal) 100-240V

Power consumption (nominal)

Power save mode Yes

Power management DVI-DMPM

Dot clock 280 MHz

OSD languages English, German, French, Dutch, Spanish, Italian, Portugese, Polish,

Dimensions with stand (W x H
xD)

Yes

Yes

Yes

Yes

Yes

1200 cd/m² typical

600 cd/m²

1200:1 typical

25 ms typical

15-129 kHz; 24-100 Hz

Black / White

DVI-D Dual Link / DisplayPort

1 upstream, 2 downstream

2.0

46W

Russian, Swedish, Chinese (simplified), Japanese, Korean, Arabic
Portrait: (w x hmax x d) 407 x 623 x 235 mm (w x hmin x d) 407 x 523 x
235 mm Landscape: (w x hmax x d) 493.5 x 579 x 235 mm (w x hmin x
d) 493.5 x 479 x 235 mm

48 K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

8. Important information

Dimensions w/o stand (W x H
xD)
Dimensions packaged (W x H
xD)
Net weight with stand 13.6 kg

Net weight w/o stand

Net weight packaged with
stand

Net weight packaged w/o stand N/A

Height adjustment range 100 mm

Tilt

Swivel -30° / +30°

Pivot

Mounting standard VESA (100 mm)

Screen protection Protective, non-reflective glass cover

Recommended modalities

Certifications CE0120 (MDD 93/42/EEC; A1:2007/47/EC class IIb product), CE

Supplied accessories

Optional accessories

QA software MediCal QAWeb

Units per pallet 4 per layer

Pallet dimensions (W x H)

Warranty

Operating temperature 0°C to 40°C (15°C to 30°C within specs)

Storage temperature -20°C to 60°C

Operating humidity 8% - 80% (non-condensing)

Storage humidity 5% - 95% (non-condensing)

407 x 493.5 x 84 mm

676 x 565 x 317 mm

8.6 kg

19.6 kg

-5° / +25°

N/A

CT, MR, US, DR, CR, NM , Film

- 2004/108/EC, CE - 93/42/EEC; A1:2007/47/EC class II b, IEC
60950-1:2005 + A1:2009 (2ND EDITION), IEC 60601-1:2005 + A1:2012,
ANSI/AAMI ES 60601-1:2005 + C1:2009 + A1:2012, CAN/C
No. 60601-1-08:2008, DEMKO - EN 60601-1:2006, EN 60601-1-2:2007,
CCC - GB9254-2008 + GB4943.1-2011 + GB17625.1-2003, KC, VCCI,
FCC class B, ICES-001 Level B, FDA 510(k), RoHS
User Guide

Quick Installation Sheet

Video cables (1 x DVI Dual Link + 1 x DisplayPort)

Main cables (UK, European (CEBEC/KEMA), USA (UL/ CSA; adaptor
plug NEMA 5-15P), Chinese (CCC))
USB 2.0 cable

External power supply

None

80 cm x 120 cm

5years

SAC22.2

Operation altitude

Storage altitude

8.8 Open sourc

e license information

2000 m

7500 m

Open source license information

Open source license usage

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

49

8. Important information

This product contains software components released under an Open Source license. A copy of the source
code is available on request by contacting your Barco customer support representative.

EACH S EPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA­TION ARE PROVIDED "AS IS" WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU­LAR PURPOSE. IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTOR
BE LIABLE FOR DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. MORE INFORMATION/DETAILS IS TO BE FOUND IN EACH SPE­CIFIC OPEN SOURCE LICENSE.

Copyright on each Open Source Software component belongs to the respective initial copyright holder,
each additional contributor and/or their respective assignee(s), as may be identified in the respective doc­umentation, source code, README file, or otherwise. You shall not remove or obscure or otherwise alter
the respective copyrights.

You acknowledge living up to the conditions of each separate Open Source Software license.

A list of the Open Source Software components used is available in the applicable EULA, through the
(customer section of the) Barco website or through other (online) means.

50

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014