Page 1
Setting Up Video Routings
The MatrixPRO-II DVI 16x16 Router uses a more efficient
method of routing. A Video Input can be linked to multiple
Outputs with a single entry. Follow the steps below to setup a Video Routing from the front panel.
The MP-II DVI 16x16 Router System settings and
functions listed below can be changed using the “FUNC”
Key. Pressing the FUNCTION key will allow you to cycle
through the following features:
PC Program Operation
A PC Program has been included on the MP-II DVI product
CD. This program provides a user friendly graphic interface
(GUI) alternative to front panel and command input
operation. Additional info on this software can be found in
section 5 of the User’s Guide.
To install the program on your PC just run the MPIIDVISetup program that is located in the MPII-DVI folder on
the product CD.
Input Selection Section
Provides 16 DDC/HDCP Compliant
DVI Inputs
Menu Display
Use Func Key for
System Set-Up and
Link Key to make
Input/Output
connections
Control Keys
Link Key to Set-Up Video Routings
Link then Shift to remove Routing
Func Key for System Set-up
“SHIFT ON PRESET” is currently unavailable.
This feature will be added in the future.
Menu Navigation
Input keys 1 thru 6 are
used to navigate in the
Function Menu
Output Selection
Section
Provides 16 DDC/HDCP
Compliant DVI Outputs
MatrixPRO-II DVI 16x16
Quick Start Guide
Visibly yours
BARC
1 2 3
987
654
1 2 3
987
654
INPUT
OUTPUT
DISPLAY
MatrixPRO-II DVI 16x16
MP-II DVI 16x16
Reset Switch
This switch puts the unit
into reset mode. Unplug
the AC power cord to
power the unit off
completely
Press the “Link” key
Select the Input Channel Number using the “Input”
Keys
Using the “Output” Keys, select all outputs you
would like to route the input to. (pressing the
output key again will de-select that output)
Press the Enter Key after selecting your Outputs to
store your Video Routing
To Clear a routing from the front panel
Press the “Link” key then Press the “Shift” Key
“UnLink” should appear on the display
Press the “Input” key you would like to clear the
routings for.
Press the Enter Key to clear all outputs associated
with the “Input” you selected.
System Set-Up
Gateway
Subnet Mask
IP Address
MAC Address (fixed value, can not be changed
from front panel)
UDP Port Number (fixed value, can not be
changed from front panel)
Video Generator (1280x1024@60Hz Vertical Bars)
Monitoring Output
EDID Configure
HDCP Configure
Baud Rate
Control Lock
Factory Reset
Remote Configuration and Control
Web Control Panel Operation
The Web control panel provides a user-friendly GUI and
easy access to control the MP-II DVI. Additional
information on the Web Control Panel can be found in
section 6 of the User’s Guide.
To launch the Web control panel connect your PC to the
MP-II DVI through a switch or hub. A direct connection can
be made from a PC to the MP-II DVI but may require a
crossover cable. Set-up your PC Network Properties as
instructed in section 3.1 of the User’s Guide.
Launch your web browser and enter the IP address of the
MP-II DVI 16x16 into the URL address line. The factory
default IP address of the router is 192.168.0.246
Technical Support
(Europe, Middle East, Asia)
Telephone: 0800900410
Website: www.barco.com/support/eSupport.aspx
Technical Support (USA)
Telephone: (866) 374-7878
6 am to 10 pm (PST) 7 days/week
Websites: www.barco.com
www.barco.com/esupport
Page 2
Upgrading Firmware
Remote Configuration and Control
MatrixPRO-II DVI 16x16
Quick Start Guide
AC
Connect to
AC power
source.
P/N 26-1302004-00 Rev 01
Visibly yours
Input LED
Indicates
valid input
connected
DVI Inputs
16 DDC/HDCP Compliant
DVI Inputs are provided
DVI Outputs
16 DDC/HDCP Compliant
DVI Outputs are provided
Output LEDs
Indicate valid
“Hot Plug Detect”
SDVI-4EI
CH 1
CH 2 CH 3
CH 4
1
2
3
4
SDVI-4EI
CH 1 CH 2 CH 3 CH 4
1
2
3
4
SDVI-4EI
CH 1 CH 2 CH 3 CH 4
1
2
3
4
SDVI-4EI
CH 1
CH 2 CH 3
CH 4
1
2
3
4
SDVI-4EO
CH 1
CH 2 CH 3
CH 4
1
2
3
4
CH 1 CH 2 CH 3 CH 4
1
2
3
4
CH 1 CH 2 CH 3 CH 4
1
2
3
4
CH 1
CH 2 CH 3
CH 4
1
2
3
4
SDVI-4EO
SDVI-4EO
SDVI-4EO
100-240~, 47/63Hz
PM-350
SERVICE RS-232
LAN
REFERENCE
OUTPUT
MONITOR
OUTPUT
Power Supply Bay
For optional
Redundant Power
Supply Module.
Barco part number
R767420K
Service Port
Used to
upgrade product
firmware
RS-232 Port
Command input using
Hyper Terminal
(Default Baud Rate:
115200bps, N-8-1)
Ethernet Port
Command Input using TCP/
IP Telnet, Web Panel, or PC
Program GUI
(Default IP: 192.168.0.246)
Reference Output
Test pattern video
source
1280x1024@60Hz
Vertical Color Bars
Monitoring Output
Provides an additional
output to monitor Input
signals.
Command Input
The MP-II DVI 16x16 Router can also be controlled
using Command codes that are in an ASCII String
format. These strings can be sent to the Router
through a RS-232 or TCP/IP connection. The
commands can be found in section 7 of the User’s
Guide.
RS-232 default settings:
Bits per second (baud rate):
115200 (115200 is default baud
rate of MATRIXPRO-II DVI 16x16 )
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
IMPORTANT
For HDCP sources, ensure the Output
Display device is HDCP-compliant.
Otherwise, the display device will be
blacked when protected content is
selected to be shown on that output.
VGEXT
Product firmware updates are available on the Barco website at
www.barco.com. Go to Image Processing and then to Matrix
Switchers
The MegaBoot.exe software is used when downloading new
firmware to the MatrixPRO-II DVI Router. The software can be run
on a PC with Windows 7, as an Administrator or on a PC with
windows XP.
Connect your PC to the service port using the RJ11 to DB9 serial
download cable provided. Your PC serial COM port must be set
38400bps baud rate when performing firmware updates through the
service port.
For detailed instructions on updating the product firmware see
section 8 of the User’s Guide.
Supports Entire family of Barco Encore Controllers
4RU 19" rack mountable chassis
DDC/HDCP Compliant
Ability to Enable and Disable HDCP for each Input
Additional DDC/HDCP Compliant Monitor Output
Optional Redundant Power Supply
Features
Technical Support
(Europe, Middle East, Asia)
Telephone: 0800900410
Website: www.barco.com/support/eSupport.aspx
Technical Support (USA)
Telephone: (866) 374-7878
6 am to 10 pm (PST) 7 days/week
Websites: www.barco.com
www.barco.com/esupport
Loading...