Barco F80, F80-Q7, F80-4K7, F80-4K9, F80-Ultra User Manual

...

Download

Page 1

F80 series

ENABLING BRIGHT OUTCOMES

User Manual

Page 2

Registered address: Barco NV

President Kennedypark 35, 8500 Kortrijk, Belgium www.barco.com/en/support www.barco.com

Barco Fredrikstad AS

Habornveien 53, N-1630 Gamle Fredrikstad, Norway Support.fre@barco.com www.barco.com

Page 3

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Changes

Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site https://www.barco.com/en/signin.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

EMC statements

EN55032/CISPR32 Class A MME (MultiMedia Equipment)

Page 4

Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment

may cause radio interference.

Class A ITE (Information Technology Equipment)

Warning : This is a class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

警告使用者: 此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。

Page 5

Table of contents

1 Safety....................................................................................................................................................................................................................9

1.1 General considerations.................................................................................................................................................................. 10

1.2 Important safety instructions ....................................................................................................................................................... 11

1.3 Product safety labels .......................................................................................................................................................................15

1.4 Risk Group 3 Safety.........................................................................................................................................................................17

1.4.1 General considerations ...............................................................................................................................................17

1.4.2 High Brightness precautions: Hazard Distance (HD).................................................................................17

1.4.3 HD for fully enclosed projection systems ..........................................................................................................19

1.4.4 HD in function of the lens Throw Ratio (TR)....................................................................................................20

2 Remote Control Unit.........................................................................................................................................................................21

2.1 Remote control, battery installation......................................................................................................................................... 22

2.2 Using the XLR connector of the RCU ....................................................................................................................................23

2.3 Remote control, on/off button .....................................................................................................................................................23

3 Input & Communication ...............................................................................................................................................................25

3.1 Introduction ........................................................................................................................................................................................... 26

3.2 Connection Panel..............................................................................................................................................................................26

3.3 Making connections .........................................................................................................................................................................27

3.4 Connector specifications...............................................................................................................................................................27

3.4.1 DVI-I.......................................................................................................................................................................................27

3.4.2 Display Port 1.2 ...............................................................................................................................................................28

3.4.3 HDMI 2.0 .............................................................................................................................................................................28

3.4.4 3G-SDI.................................................................................................................................................................................. 29

3.4.5 HDBase T ........................................................................................................................................................................... 29

3.5 Control interfaces ..............................................................................................................................................................................30

3.5.1 RS-232 .................................................................................................................................................................................30

3.5.2 LAN/Ethernet .................................................................................................................................................................... 30

3.5.3 USB-A port .........................................................................................................................................................................30

3.6 LED and Button indication chart ............................................................................................................................................... 31

4 Getting Started........................................................................................................................................................................................33

4.1 Functionality overview ....................................................................................................................................................................34

4.2 Power modes.......................................................................................................................................................................................36

4.3 Power mode transitions .................................................................................................................................................................36

4.3.1 General ................................................................................................................................................................................36

4.3.2 Power on projector.........................................................................................................................................................37

R5906852-01 F80 series

Page 6

4.3.3 Going from READY to ON .........................................................................................................................................37

4.3.4 Going from ON to READY.........................................................................................................................................37

4.3.5 Going from READY to ECO standby...................................................................................................................37

4.3.6 Going from ECO to ON ...............................................................................................................................................37

4.3.7 Wake on LAN (WOL)....................................................................................................................................................37

4.4 Status overview .................................................................................................................................................................................. 38

4.5 Power off projector............................................................................................................................................................................38

4.6 Increasing the projector life time...............................................................................................................................................39

4.7 Operation in 24/7 Mode .................................................................................................................................................................39

4.8 Using the RCU ....................................................................................................................................................................................39

4.9 Projector Address..............................................................................................................................................................................41

4.9.1 Controlling the projector .............................................................................................................................................41

4.10 Quick setup via Direct access ....................................................................................................................................................42

5 Graphic User Interface (GUI)...................................................................................................................................................45

5.1 Overview ................................................................................................................................................................................................46

5.2 Navigation..............................................................................................................................................................................................46

5.3 Test Patterns ........................................................................................................................................................................................47

6 GUI – Source..............................................................................................................................................................................................49

6.1 Displaying a single source............................................................................................................................................................50

6.2 Connector Settings........................................................................................................................................................................... 50

7 GUI – Image.................................................................................................................................................................................................53

7.1 Setting image levels manually....................................................................................................................................................54

7.2 Adjusting the sharpness ................................................................................................................................................................56

7.3 Adjusting the gamma correction ...............................................................................................................................................57

7.4 P7 Realcolor.........................................................................................................................................................................................57

7.5 HDR – Perceptual Quantizer (PQ)...........................................................................................................................................60

8 GUI – Installation ..................................................................................................................................................................................61

8.1 Configuring the lens, shift .............................................................................................................................................................62

8.2 Orientation.............................................................................................................................................................................................62

8.3 Warping...................................................................................................................................................................................................63

8.3.1 About warping .................................................................................................................................................................. 63

8.3.2 Warping – On/Off ............................................................................................................................................................ 63

8.3.3 Warping – Screen Size................................................................................................................................................64

8.3.4 Warping – 4 corners adjustment ............................................................................................................................65

8.3.5 Warping – Bow .................................................................................................................................................................67

8.3.6 Warping – Warp files .....................................................................................................................................................70

8.3.7 Warping – Latency control in a multi projector setup .................................................................................. 72

8.4 Blending..................................................................................................................................................................................................73

8.4.1 Blend & Mask....................................................................................................................................................................74

8.4.2 Black level adjustment.................................................................................................................................................77

8.4.3 Black Level Files .............................................................................................................................................................78

8.4.4 Blend Files.......................................................................................................................................................................... 79

8.5 Laser illumination .............................................................................................................................................................................. 80

9 GUI – System Settings....................................................................................................................................................................83

9.1 Communication...................................................................................................................................................................................84

9.1.1 Introduction to a Network connection.................................................................................................................. 84

R5906852-01 F80 series6

Page 7

9.1.2 Wired IP address set up .............................................................................................................................................84

9.2 Themes ...................................................................................................................................................................................................86

9.3 Standby ECO.......................................................................................................................................................................................86

9.4 Service Menu.......................................................................................................................................................................................87

9.4.1 Service – Color Wheel .................................................................................................................................................87

9.4.2 Service – Color................................................................................................................................................................. 88

9.4.3 Service – Statistics......................................................................................................................................................... 89

9.4.4 Lens Calibration .............................................................................................................................................................. 90

9.4.5 Service – Pixel Shift ......................................................................................................................................................91

9.5 Reset ........................................................................................................................................................................................................92

10 Status menu ..............................................................................................................................................................................................95

10.1 Status menu overview ....................................................................................................................................................................96

11 Maintenance..............................................................................................................................................................................................99

11.1 Cleaning the lens ............................................................................................................................................................................ 100

11.2 Cleaning the exterior of the projector .................................................................................................................................. 100

11.3 Filters..................................................................................................................................................................................................... 100

A Specifications...................................................................................................................................................................................... 101

A.1 Specifications of the F80-Q7....................................................................................................................................................102

A.2 Specifications of the F80-Q9....................................................................................................................................................103

A.3 Specifications of the F80-4K7 ................................................................................................................................................. 104

A.4 Specifications of the F80-4K9 ................................................................................................................................................. 106

A.5 Dimensions of a F80 .................................................................................................................................................................... 107

A.6 Technical Regulations..................................................................................................................................................................108

B Environmental information................................................................................................................................................... 109

B.1 Disposal information ......................................................................................................................................................................110

B.2 China RoHS compliance .............................................................................................................................................................110

B.3 Taiwan RoHS compliance...........................................................................................................................................................112

B.4 Turkey RoHS compliance...........................................................................................................................................................113

B.5 Production address ........................................................................................................................................................................113

B.6 Contact information ........................................................................................................................................................................113

B.7 Product Info (Taiwan)....................................................................................................................................................................113

B.8 Download Product Manual .........................................................................................................................................................114

R5906852-01 F80 series 7

Page 8

R5906852-01 F80 series8

Page 9

Safety 1

About this document

Read this document attentively. It contains important information to prevent personal injury while installing and using the F80 projector. Furthermore, it includes several cautions to prevent damage to the F80 projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing the F80 projector.

Clarification of the term “F80” used in this document

When referring in this document to the term “F80” means that the content is applicable for following Barco products:

• F80-Q7, F80-Q9, F80-4K7, F80-4K9, F80-Ultra

Model certification name

•

GPC

R5906852-01 F80 series

Page 10

Safety

1.1 General considerations

General safety instructions

•

Before operating this equipment please read this manual thoroughly and retain it for future reference.

• Installation and preliminary adjustments should be performed by qualified Barco personnel or by

authorized Barco service dealers.

• All warnings on the projector and in the documentation manuals should be adhered to.

• All instructions for operating and use of this equipment must be followed precisely.

• All local installation codes should be adhered to.

Notice on safety

This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, as basis for National safety regulation world wide. The safety standard covers information technology equipment including electrical business equipment intended to operate in “normal” environments (offices and homes). This safety standard imposes important requirements on the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing reduce the risk of hazards and contribute to ensure the safety of the equipment to the user even when the equipment’s normal operation fails.

Notice on optical radiation

This projector embeds extremely high brightness (radiance) lasers; this laser light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a significant risk for the human eye when exposed directly within the beam. This risk is not specific related to the characteristics of laser light but solely to the high thermal induced energy of the light source; which is equivalent with lamp based systems.

Thermal retinal eye injury is possible when exposed within the Hazard Distance (HD). The HD is defined from the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as described in the chapter “Hazard Distance”.

Notice on optical radiation (addendum)

•

F80-Ultra, F80-Q9, F80-4K9 :

- The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. The projector

conforms with IEC 60825–1:2007, and with performance standards for laser products under 21 CFR 1040, except with respect to those characteristics authorized by Variance Number 2017-V-4837 effective September 13, 2017 Do not stare into Beam.

- This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk

Group 3 (RG3) when an interchangeable lens with throw ratio greater than 2.8 is installed. For Northern America, installation requirements according to Risk group 3 (RG3) must be followed when interchangeable lens with throw ratio greater than 2.0 is installed. Refer to the manual for the lens list and throw ratio before operation. Such combination of projector and lens are intended for professional use only, and are not intended for consumer use. Safety considerations for RG3 projectors are discussed in section “Risk Group 3 Safety”, page 17.

- This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very

dangerous and should never be attempted.

• F80-Q7, F80-4K7 :

- The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. The projector

- This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk

Group 3 (RG3) when an interchangeable lens with throw ratio greater than 3.5 is installed. For Northern America, installation requirements according to Risk group 3 (RG3) must be followed when

R5906852-01 F80 series10

Page 11

Safety

interchangeable lens with throw ratio greater than 2.0 is installed. Refer to the manual for the lens list and throw ratio before operation. Such combination of projector and lens are intended for professional use only, and are not intended for consumer use. Safety considerations for RG3 projectors are discussed in section “Risk Group 3 Safety”, page 17.

- This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very

dangerous and should never be attempted.

Users definition

Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL. When installing an interchangeable lens with a throw ratio that make the projector become RG3, refer to chapter “Risk Group 3 Safety”, page 17. Such combination of projector and lens are intended for professional use only, and are not intended for consumer use.

FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED PERSONNEL familiar with potential hazards associated with high intensity light beams.

1.2 Important safety instructions

To prevent the risk of electrical shock

•

This product should be operated from a mono phase AC power source.

• This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the

supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the groundingtype plug. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.

• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the

cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• Use only the power cord supplied with your device. While appearing to be similar, other power cords have

not been safety tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.

• Do not operate the projector with a damaged cord. Replace the cord.

• Do not operate the projector if the projector has been dropped or damaged - until it has been examined

and approved for operation by qualified service personnel.

• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should

be used. A cord rated for less amperage than the projector may overheat.

• Never push objects of any kind into this product through cabinet slots as they may touch dangerous

voltage points or short out parts that could result in a risk of fire or electrical shock.

• Make sure that no objects enter into the vents and openings of the set.

• Do not expose this projector to rain or moisture.

• The projector is designed for indoor use only. Never operate the unit outdoors.

• Do not immerse or expose this projector in water or other liquids.

• Do not spill liquid of any kind on this projector.

• Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified

service personnel before resuming operations.

• Do not disassemble this projector, always take it to qualified service personnel when service or repair

work is required.

• Do not use an accessory attachment which is not recommended by the manufacturer.

R5906852-01 F80 series 11

Page 12

Safety

• Lightning - For added protection for this video product during a lightning storm, or when it is left

unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.

To prevent personal injury

•

To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or adjusting the projector.

• To prevent injury, take note of the weight of the projector. Minimum 2 persons are needed to carry the

projector. The projector weights about ±26 kg (±57 lbs) without lens and rigging frame.

• To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.

• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to

the eye.

• Warning: extremely high brightness projector: This projector embeds extremely high brightness

(radiance) lasers; this laser light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a significant risk for the human eye when exposed directly within the beam. This risk is not specific related to the characteristics of laser light but solely to the high thermal induced energy of the light source; which is comparable with lamp based systems. Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is defined from the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as described in the chapter “High Brightness precautions: Hazard Distance (HD)”, page 17.

• Based on international requirements, no person is allowed to enter the projected beam within the zone

between the projection lens and the related Hazard Distance (HD). This shall be physically impossible by creating sufficient separation height or by placing optional barriers. Within the restricted area operator training is considered sufficient. The applicable separation heights are discussed in “High Brightness precautions: Hazard Distance (HD)”, page 17.

• Don’t put your hand in front of the beam.

• This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics

inside the housing or compartments will violate any warranties and may be hazardous.

• A special device (“rigged frame”) based on an external frame must be used when the projector is deployed

in a hanging configuration, or when several projector must be stacked. See installation manuals for the correct use of these devices.

• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious

damage to it and possible injury to the user.

• It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if

they have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.

• Cooling liquid circuit. The projector contains a cooling circuit filled with Green Ethylene glycol diluted

(53% Glycol – 47% Demi water). When the cooling circuit leaks, switch off the device and contact qualified service personnel. The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.

• Never point or allow light to be directed on people or reflective objects within the HD zone.

• All operators shall have received adequate training and be aware of the potential hazards.

• In case of using an external cooling system position the hoses of the cooling system so that they will not

be tripped over, pulled, or contact hot surfaces.

To prevent fire hazard

•

Do not place flammable or combustible materials near the projector!

• Barco projection products are designed and manufactured to meet the most stringent safety regulations.

This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is

R5906852-01 F80 series12

Page 13

Safety

absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone in the exhaust area must be not less than 100 cm (40”). The exclusion zone on the intake area must be not less than 50 cm (20”).

• Do not place any object in the projection light path at close distance to the projection lens output. The

concentrated light at the projection lens output may result in damage, fire or burn injuries.

• Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable

and combustible materials away from the projector at all times. Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In the event of fire, use sand, CO electrical fire. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this projector.

or dry powder fire extinguishers. Never use water on an

• Ensure no misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) can

represent a fire risk. After alignment the projector shall be securely mounted to the pedestal.

• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the

projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent

hot exhaust air from projector and cooling system to the outside of the building.

• Let the projector cool completely before storing. Remove cord from the projector when storing.

To prevent projector damage

•

Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens.

• The air filters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area

would be monthly-minimum. Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation.

• The projector must always be installed in a manner which ensures free flow of air into its air inlets.

• If more than one projector is installed in a common projection booth, the exhaust air flow requirements are

valid for EACH individual projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector as a whole as well as causing premature failure of the lasers.

• In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic

Compatibility (EMC) and safety requirements, it should always be operated with all of it's covers in place.

• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product

and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and

remove all power from the projector. Do not operate the projector again until it has been checked by qualified service personnel.

• Do not block the projector cooling fans or free air movement around the projector.

• Do not use this equipment near water.

• Special care for Laser Beams: Special care should be used when DLP projectors are used in the same

room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices

in which case there is a loss of warranty.

• Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror

Devices

in which case there is a loss of warranty.

• Save the original shipping carton and packing material. They will come in handy if you ever have to ship

your equipment. For maximum protection, repack your set as it was originally packed at the factory.

• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive

R5906852-01 F80 series 13

Page 14

Safety

cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.

• To ensure the highest optical performance and resolution, the projection lenses are specially treated with

an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. For lens cleaning follow the instructions precisely as stipulated in the projector manual.

• Only connect the projector to signal sources and voltages as described in the technical specification.

Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of the unit.

• Allowed ambient temperature range: t

= 10°C (50°F) to 40°C (104°F)

• Rated humidity = 20% RH to 80% RH Non-condensed.

• Do not operate the projector outside its temperature and humidity specifications as this may result in

overheating and malfunction.

On servicing

•

Do not attempt to service this product yourself. This product contains no user serviceable parts except parts describe in the User manual. Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may expose you to dangerous voltage potentials, risk of electric shock and retinal eye injury.

• Refer all servicing to Barco authorized repair centers.

• Attempts to alter the factory-set internal controls or to change other control settings not specially

discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty.

• Remove all power from the projector and refer servicing to Barco authorized repair center under the

following conditions:

- When the power cord or plug is damaged or frayed.

- If liquid has been spilled into the equipment.

- If the product has been exposed to rain or water.

- If the product does not operate normally when the operating instructions are followed. Adjust only

those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has been damaged.

- If the product exhibits a distinct change in performance, indicating a need for service.

• Replacement parts: When replacement parts are required, be sure the service technician has used

original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.

• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to

perform safety checks to determine that the product is in proper operating condition.

Safety Data Sheets for Hazardous Chemicals

For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available upon request via safetydatasheets@barco.com.

R5906852-01 F80 series14

Page 15

1.3 Product safety labels

Light beam related safety labels

Label image Label description Label location

Refer to user manual for further information!

Caution! Do not stare into beam, RG2 product.

Safety

Hazard RG3: not for household use symbol.

R5906852-01 F80 series 15

Page 16

837

Safety

Label image Label description Label location

Hazard RG3: optical radiation warning symbol.

For F80-Q7, F80-4K7:

For North America: THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER 2017-V-4837 EFFECTIVE September 13, 2017. This projector may become RG3 when an interchangeable lens with throw ratio greater than 3.5 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use. Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif interchangeable dont le rapport de projection est supérieur à 3.5. Veuillez vous reporter au manuel pour en savoir plus sur la liste des objectifs et la distance de sécurité avant toute utilisation. De telles combinaisons entre projecteur et objectif sont conçues pour des applications professionnelles uniquement et pas pour des applications grand public.

本投影机安装透射比大于3.5的可换镜头后，可成为RG3，操作前，请参考手册中镜头清单和危险距离。本投影机与镜头组合仅供专业使用，非普通消费者使用。

For F80-Ultra, F80-4K9, F80-Q9 :

For North America: THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER 2017-V-4837 EFFECTIVE September 13, 2017. This projector may become RG3 when an interchangeable lens with throw ratio greater than 2.8 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use. Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif interchangeable dont le rapport de projection est supérieur à 2.8. Veuillez vous reporter au manuel pour en savoir plus sur la liste des objectifs et la distance de sécurité avant toute utilisation. De telles combinaisons entre projecteur et objectif sont conçues pour des applications professionnelles uniquement et pas pour des applications grand public.

本投影机安装透射比大于2.8的可换镜头后，可成为RG3，操作前，请参考手册中镜头清单和危险距离。本投影机与镜头组合仅供专业使用，非普通消费者使用。

R5906852-01 F80 series16

Page 17

Safety

1.4 Risk Group 3 Safety

1.4.1 General considerations

Notice on optical radiation from F80 Projector when it becomes Risk Group 3.

•

For RG3, no direct exposure to the beam shall be permitted. For RG3, operators shall control access to the beam within the hazard distance or install the product at a height that will prevent eye exposure within the hazard distance.

• This projector has one or several built-in Class 4 laser clusters. Disassembly or modification is very

dangerous and should never be attempted.

• Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous

laser radiation exposure.

• Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.

FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED PERSONNEL familiar with potential hazards associated with high intensity light beams.

WARNING: No direct exposure to the beam within the hazard distance shall be permitted, RG3 (Risk Group 3) IEC 62471-5:2015

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

1.4.2 High Brightness precautions: Hazard Distance (HD)

Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the light source is less than the HD.

Restriction Zone (RZ) based on the HD

The HD depends on the amount of lumens produced by the projector and the type of lens installed. See next chapter“HD in function of the lens Throw Ratio (TR)”, page 20.

To protect untrained end users (as cinema visitors) the installation shall comply with the following installation requirements: Operators shall control access to the beam within the hazard distance or install the product at the height that will prevent spectators' eyes from being in the hazard distance. Radiation levels in excess of the limits will not be permitted at any point less than 2.0 meter (SH) above any surface upon which persons other than operators, performers, or employees are permitted to stand or less than 1.0 meter (SH) lateral separation from any place where such persons are permitted to be. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual's shoulders, within the HD.

These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section

6.6.5. The end user must understand the risk and apply protective measures based upon the hazard distance as

indicated on the label and in the user information. Installation method, barriers, detection system or other applicable control measure shall prevent hazardous eye access to the radiation within the hazard distance.

For example, projectors that have a HD greater than 1 m and emit light into an uncontrolled area where persons may be present should be positioned in accordance with “the fixed projector installation” parameters, resulting in a HD that does not extend into the audience area unless the beam is at least 2.0 meter above the floor level. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual's shoulders, within the HD. For example, a sufficiently large

R5906852-01 F80 series 17

Page 18

EXIT

(B) TOP VIEW(A) SIDE VIEW

Safety

separation height may be achieved by mounting the image projector on the ceiling or through the use of physical barriers.

For applications installed in the USA market the above limits for cinema like environments do not apply. The relevant minimum separation height is 2.5m (8,2 ft) by the FDA CDRH. Non cinema like environments require

2.5 meter (8.2 ft) separation height and 1.0 meter (3.3 ft) separation width for areas where restrained behavior is to be expected. All other areas require 3.0 (9.9 ft) separation height.

Image 1-1

A Side view. B Top view. RA Restricted Access location (boot area of projector). PR Projector.

TH Theater. RZ Restriction Zone in the theater. SH Separation Height. SW Separation Width.

Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related hazard distance (HD). This shall be physically impossible by creating sufficient separation height or by placing barriers. The minimum separation height takes into account the surface upon which persons other than operator, performers or employees are permitted to stand.

OnImage 1-2 a typical setup is displayed. It must be verified if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in Image 1-2.

The restricted area sticker can be replaced by a sticker with only the symbol.

R5906852-01 F80 series18

Page 19

RESTRICTED

AREA

RESTRICTED

AREA

RA TH

DIFFUSE

REFLECTION

RESTRICTED

AREA

RESTRICTED

AREA

Safety

Image 1-2

1.4.3 HD for fully enclosed projection systems

Restriction Zone (RZ) based on the HD

The projector is also suitable for rear projection applications; projecting a beam onto a defuse coated projection screen. As displayed in Image 1-3 two areas should be considered: the restricted enclosed projection area (RA) and the observation area (TH).

Image 1-3

RA Restricted Access location (enclosed projection area). PR Projector. TH Theater (observation area).

RZ Restriction Zone. PD Projection Distance. SW Separation Width. Must be minimum 1 meter.

R5906852-01 F80 series 19

Page 20

0.5

1.5

2.5

3.5

4.5

0.4 0.8 1.2 1.6 2.0 2.3 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 5.9 6.3 6.7 7.1 7.5 7.9 8.3 8.7 9.1 9.5 9.9

Hazard distance [m]

Throw Ra!o

F80-Q7, F80-4K7 F80-Ultra, F80-Q9, F80-4K9

Safety

For this type of setup 3 different HD shall be considered:

• HD as discussed in “High Brightness precautions: Hazard Distance (HD)”, page 17, relevant for intrabeam

exposure.

• HD

reflection

screen.

• HD

diffuse

screen.

As described in “High Brightness precautions: Hazard Distance (HD)”, page 17, it is mandatory to create a restricted zone within the beam areas closer than any HD. In the enclosed projection area the combination of two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to the rear reflection from the screen (HD

The HD distance to the rear projection screen. To determine the HD distance for the used lens and projector model see graphs in chapter “HD in function of the lens Throw Ratio (TR)”, page 20.

reflection

The light emitted from the screen within the observation shall never exceed the RG2 exposure limit, determined at 10 cm. The HD cd/m² or 15000 LUX.

: the distance that has to be kept restrictive related to the reflected light from the rear projection

: the relevant distance to be considered while observing the diffuse surface of the rear projection

); also taking into account a 1 meter lateral separation.

reflection

distance equals 25% of the difference between the determined HD distance and the projection

= 25% (HD – PD)

can be neglected if the measured light at the screen surface is below 5000

diffuse

1.4.4 HD in function of the lens Throw Ratio (TR)

TR (Throw Ratio)

The ratio of the distance to the screen (throw) to the screen width.

HD versus Throw Ratio

Image 1-4

Graph shows Hazard Distance in meters versus Throw ratio of the lens

R5906852-01 F80 series20

Page 21

Remote Control Unit 2

21R5906852-01 F80 series

Page 22

Remote Control Unit

2.1 Remote control, battery installation

Where to find the batteries for the remote control ?

The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control, install the batteries first.

How to install

1. Push the battery cover tab with the fingernail a little backwards (1) and pull, at the same time, the cover

upwards (2).

Image 2-1

2. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery

compartment.

Tip: Use alkaline batteries for optimum range and life time.

Image 2-2

3. Insert (1) both lower tabs of the battery cover in the gaps at the bottom of the remote control, and press (2) the

cover until it clicks in place.

Image 2-3

R5906852-01 F80 series22

When replacing batteries, the broadcast address of the RCU will be reset to its default value '0'.

Page 23

CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of

explosion if the battery is replaced with an incorrect type.

CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly installed.

2.2 Using the XLR connector of the RCU

Connecting a cable with the XLR connector will reset the broadcast address of the RCU to its default value '0'.

How to use the XLR connector

1. Remove the XLR cover by pulling it backwards.

Remote Control Unit

Image 2-4

2. Connect a cable with XLR plug into the XLR connector of the RCU.

3. Connect the other end of the cable with the XLR input of the projector.

2.3 Remote control, on/off button

Purpose of the remote control on/off button

The Pulse remote control unit has at the front side an on/off switch (reference 1 Image 2-5). Switching off the remote control prevents that unwanted commands are send due to an accidental key press. Furthermore, switching the RCU off will extend the battery life time of the remote control.

To activate the remote control press the on/off button. To deactivate the remote control press the on/off button again. Default when (re)placing batteries, is “ON”.

Image 2-5

R5906852-01 F80 series 23

Page 24

Remote Control Unit

R5906852-01 F80 series24

Page 25

Input & Communication

Overview

•

Introduction

• Connection Panel

• Making connections

• Connector specifications

• Control interfaces

• LED and Button indication chart

R5906852-01 F80 series

Page 26

1 2

1 3 6 8

2 4 5 7 9 1110 12

Input & Communication

3.1 Introduction

General

The Input & Communication features of the projector consists of a local keypad and a communication panel situated at the left side, and a connection panel (sources and control connections) located at the back side.

Image 3-1

1 local keypad and a communication panel 2 connection panel

3.2 Connection Panel

General

Projector sources and control connections are located at the back of the projector.

Image 3-2

Nb.Name Pcs Description Purpose

1 DMX IN/

OUT

2 RS-232 1 9–pin DB9 connector For Projector Control. Allows for wired remote

3 Sync 3 BNC Sync Port IN/OUT;

2 DMX 512 input / DMX 512

output

Bidirectional mini-DIN (1x 3D sync Out, and 2x Sync In/Out)

For Projector Control

control and monitoring of many projector functions used in installation environments

For Projector Control. This is mainly used in multiple projector installations with requirement of synchronization between the units

4 Trigger 2 12VDC - 0,5A (6W) For Controlling Peripherals, like motorized

screens, curtains etc. Give 12V output when

5 RC 1 Mini jack 3,5mm connector for

wired remote

6 USB 2 USB 2.0 type A, 4 pin( 2x

Rear and 1x Front)

7 LAN 1 Standard RJ45 connector For Projector Control

R5906852-01 F80 series26

projector are switched onSee also the note

below.

For Projector Control

For Software upgrade

Page 27

Nb.Name Pcs Description Purpose

8 DP 2 Standard display port For Projector Input

Input & Communication

9 DL-DVI-D 2 Dual DVI-I 1.0 (DVI_D

Functionallity).

10 HDMI 1 Standard HDMI 2.0 For Projector Input

11 HDBaseT 1 Standard RJ45 8P8C

Connector

12 SDI 2 SDI1 is Input, SDI 2 is pass

through. (out)

Regarding the Trigger Output: If these outputs are loaded too heavy, there is a risk that the projector will go in reset mode, and restart. This causes no damage to the projector, but is an undesirable response. This will also happen if the startup current for the external equipment is too high, even though the nominal power consumption is less than 0,5A.

For Projector Input. These connectors can also be used to form one uniform image by feeding half of the image into each connector. HDCP compliant for sources up 165 Mhz

For Projector Control

For Projector Input

3.3 Making connections

The source switching time varies from 0.5 to 5 seconds.

Source signal connectivity

The connector panel at the back of the projector is used for all source connections. Source signal connectivity on the projector is:

• 2x Dual Link DVI-I (DVI-D functionality)

• 2x DisplayPort 1.2

• 1x HDMI 2.0

• 1x HDBaseT

• 1x 3G SDI

3.4 Connector specifications

Overview

•

DVI-I

• Display Port 1.2

• HDMI 2.0

• 3G-SDI

• HDBase T

3.4.1 DVI-I

Specifications

Parameter Value

Connector DVI-I female digital RGB

Signal characteristics DVI 1.0, Digital, TMDS

R5906852-01 F80 series 27

Page 28

Input & Communication

Parameter Value

Max. cable length 25 m (24 AWG)

Max. pixel rate 330 MHz (dual link), 165 Mhz (single link)

Scan format Progressive

Max. input data resolution 1920x1200 60Hz (Single link), 2560x1600 60Hz

(Dual Link).1920x2400 @60Hz

Bit depth 8 bit

EDID Supported

HDCP Supported

3.4.2 Display Port 1.2

Specifications

Parameter Value

Connector Standard Display port

Signal characteristics DP 1.2

Functionality Mandatory

Max. cable length 15 m (24 AWG) - RBR;

2 m (24 AWG) – HBR1, HBR2

Supported Link Rate RBR, HBR1, HBR2

Scan format Progressive

Max. input data resolution 2560x1600@120Hz WQXGA / 3840x2400 @60Hz

(4K ) Max

Bit depth 8, 10, 12 bit

EDID Supported

3.4.3 HDMI 2.0

Specifications

Regarding HDMI 2.0: The decryption protocol HDCP 2.2 are enabled and valid in this unit.

Parameter Value

Connector Standard HDMI

Signal characteristics Digital, TMDS

Max. cable length 15 m (24 AWG)

Max. pixel rate 594MHz

Max. input data resolution 3840x2160 @60Hz

Bit depth 8, 10, 12 bits

EDID Supported

HDCP Supported

R5906852-01 F80 series28

Page 29

Input & Communication

Parameter Value

Ethernet No

Audio return No

3.4.4 3G-SDI

Specifications

Parameter Value

Standard SMPTE 424M-2006 10bit level A

Connectors 1x) BNC 75 ohm type IEC 60169-8, Amendment 2

1997, A

Bandwidth >3 GHz

Return loss >10dB at 3GHz

Impedance 75 ohm resistive

3.4.5 HDBase T

Specifications

Parameter Value

Reference specification HDBaseT 1.0 Specification, June 2010

Connector Standard RJ-45, 8P8C

Signal characteristics HDBaseT

Max. cable length (1080p/48b/60Hz) 100 m (Cat5e/6), Pixel Clock <=225HHz, Video

Datarate <=5.3Gbps 70 m (Cat5e/6), Pixel Clock >225HHz, Video Datarate >5.3Gbps 100 m (Cat6a/7), Pixel Clock >225HHz, Video Datarate >5.3Gbps

Max TMDS Clock Frequency 270 MHz

Max video resolution supported 1920x1200 @60Hz (WUXGA 60Hz)

HDCP Pass-Through Yes, from Source to Projector

IR Extension Not Supported

RS-232 Extension Not Supported

10/100Mbps Ethernet Pass-Through Not Supported

Fallback to 100BaseTx, IEEE 802.3u Not Supported

USB Over Centre Tap Not Supported

Power Over Ethernet Not Supported

R5906852-01 F80 series 29

Page 30

Input & Communication

Parameter Value

Audio Not Supported

LEDs - HD Base Status Operation: Green, Left

Link/Mode: Yellow, Right

3.5 Control interfaces

About

The following control interfaces are available on the projector:

• 1x RS-232 (for projector control)

• 1x LAN/Ethernet (for projector control

• 3x USB-A ports

Overview

•

RS-232

• LAN/Ethernet

• USB-A port

3.5.1 RS-232

Specifications

Parameter Value

RS-232 connector 1 female DB9 connector (RS232-in) for projector

control and debug

3.5.2 LAN/Ethernet

Specifications

Parameter Value

Ethernet connector 1 RJ45 Connector for projector control (not content)

Protocols DHCP, TCP/IP, UDP/P

Speed 10/100 Mbit/1000Mbit

3.5.3 USB-A port

Specifications

Parameter Value

USB connector Type A

Function Firmware upgrade using USB sticks

R5906852-01 F80 series30

Page 31

Power Power 5V, max 1,5A (out)

Standard USB 2.0

3.6 LED and Button indication chart

Button Backlight Status

Button Color status Description

Standby button

Shutter button

Blinking WHITE (slow) Projector starts up (booting)

Blinking WHITE (fast) Firmware upgrade

Solid WHITE Projector is in Standby mode

Blinking BLUE Projector goes to ON mode

Solid BLUE Projector is ON

Blinking RED Error condition

Off (no color) Projector is OFF, starts up, or is in

Standby mode.

Solid WHITE Projector is ON, shutter is open

Solid RED Projector is ON, shutter is closed

Input & Communication

LED Status

The LED status is located on the top side of the projector, near the IR receiver. During normal operation the LED is unlit. In the event of a critical error or high temperature, the LED will

display red. By critical error, the projector cannot be restarted until the projector is disconnected from the power supply

and then reconnected again. If the reason for the error persist, the projector will again go to critical error status.

By high temperature, the projector will restart when it has cooled down, and temperatures are back within the normal operating limitations.

R5906852-01 F80 series 31

Page 32

Input & Communication

R5906852-01 F80 series32

Page 33

Getting Started 4

About this chapter

This chapter describes how to power up, control and set up your projector setup when the physical installation process is complete.

How controlling the projector ?

The projector can be controlled by the local keypad, by the remote control unit or by browser application.

Location of the local keypad ?

The local keypad is located on the right side of the projector.

Remote control functions.

This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely. This remote control is used for source selection, control, adaptation and set up.

Other functions of the remote control are :

• switching between stand by and operational mode.

• switching to "pause" (blanked picture, full power for immediate restarting)

• direct access to all connected sources.

Overview

•

Functionality overview

• Power modes

• Power mode transitions

• Status overview

• Power off projector

• Increasing the projector life time

• Operation in 24/7 Mode

• Using the RCU

• Projector Address

• Quick setup via Direct access

R5906852-01 F80 series

Page 34

1 2 3 4 5 6

1011 9 8 7

Getting Started

4.1 Functionality overview

Local Keypad overview

Menu navigation

Menu confirmation, OK button

Menu Open / Close

Menu back

Power On/Off

Project OSD On / Off

Input selection

Shutter open / close

Test patterns

Lens adjustment

LCD panel

The Keypad gives direct access to several functions, in addition to access to the menu system. The keypad has a back light that can be switched on and off manually. The light turns off automatically after a

preselected time. The Power button and Shutter buttons are equipped with white, blue and red backlit LEDs. The other keys are

only equipped with white and blue backlit LEDs. The LEDs are controlled according to the features available.

R5906852-01 F80 series34

Page 35

Remote Control Unit buttons

2625

Getting Started

Button pressed indicator

Shutter open

Shutter close

LCD panel On / Off

Project OSD On/Off

Lens zoom

Lens shift

Menu Open / Close

Menu selection, OK button

Menu navigation

Input selection

Address button

Numeric buttons

Backspace (while entering values)

XLR connector

Decimal mark (while entering values)

Macro button

Menu back

Default value button

Lens focus

Color menu

Test patterns

Power On

Power Off

3.5 mm jack

RCU On / Off

The projector remote control is a full feature wireless remote control, powered by two (2) standard AA batteries. The battery compartment is on the back of the remote control.

The remote control is backlit for use in dark environments. It also has an XLR connector for wired connection to the projector. When the wire is connected, the IR beam is switched off.

LCD panel

The LCD panel has two main functions:

1. Showing the menus, the adjustment information and also a mirror of the OSD, (On Screen Display)

described in User Interface when this is enabled. Information regarding the status of the projector showing this data:

• Projector status

• Network address

• Active source

• Current firmware version

• Operation Data

• Active functions (Enabled Functions).

Toggle between the two indications by using the Menu button on the keypad, or on the remote control. The LCD Display will fade out 30 seconds after the last key operation.

R5906852-01 F80 series 35

Page 36

ECO

READY

50%

Getting Started

4.2 Power modes

General

The table below details the F80 power modes.

Mode Description

ON (normal) Projector is booted up and the light source is on

READY Projector is booted up but the light source is off

ECO (Standby) Light source is switched off and projector electronics

are powered down

Energy consumption is significantly lowers in ECO (Standby) mode: only <0.5W if network is not plugged in and 2W with network (Wake-on-LAN).

In ECO (Standby) mode, remote power up (Wake-on-LAN) and local power up (button) are supported.

4.3 Power mode transitions

4.3.1 General

Transition Diagram

This diagram shows all modes available on the projector (unplug, ON, READY, ECO), and the actions necessary to change mode.

Image 4-1

Projector mains powered

Auto transition after x minutes if ECO mode enables

Press power On/Off button, remote On/Off button

R5906852-01 F80 series36

Page 37

Getting Started

4.3.2 Power on projector

If not already connected, connect the female side of the power cord with the power input socket of the projector. For more details see section dedicated to the power cord installation.

The background image of the startup screen and info screens can be changed with Projector Toolset with an installed F80 plug-in.

Description

Plug the 3-prong plug of power cord into a grounded AC outlet. The projector will go to READY mode. During this stage the system boots and performs the internal check of the boards. The Power On/Off button will BLINKING WHITE until READY mode is achieved. Once in READY mode, the Power On/Off button will be lit WHITE.

4.3.3 Going from READY to ON

Description

Press the Power On/Off button on the projector, or the Power On button on the remote control. The projector will power ON. The Power On/Off button will BLINK BLUE during the transition from READY to ON. Once the projector is on, the Power On/Off button will be lit BLUE.

4.3.4 Going from ON to READY

Description

Press and hold the Power on/off button on the projector for 3 seconds, or press the Power Off button on the remote control. The projector will power down through a cool down phase. The Power on/off button will BLINK WHITE during the transition from ON to READY. Once the projector is in READY, thePower on/off button will be lit WHITE.

4.3.5 Going from READY to ECO standby

Description

If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby ECO", in User Guide) the projector will automatically go to ECO standby mode after a time-out (default 15 minutes). All electronics (including fans, pumps,...) go down except for a very small wake up controller. The Power on/off button will FLASH WHITE every second.

4.3.6 Going from ECO to ON

Description

Press the Power on/off button on the projector or the Power On button on the remote control. The projector goes from ECO directly to ON. The projector will go through the same booting phase as on power plugging, then do the transition from READY to ON. Of course startup-time will be longer then from READY to ON.

4.3.7 Wake on LAN (WOL)

Description

Wake-on-LAN (WOL), the standard ethernet network command, can be used to awakened or to turn on the projector by network message.

Used alone, the WOL command allows to switch in READY mode. A JSON command must be performed in addition to make the projector turn in to ON mode:

1. Send WOL.

2. Wait for connection to façade/prospector (the unit does provide feedback when it’s ready).

3. Wait for ready state.

R5906852-01 F80 series 37

Page 38

Getting Started

4. Sleep 5 seconds.

5. Send power on command (to switch in ON mode).

4.4 Status overview

Description

Once the projector is started, press Status to get an overview of parameters such as :

• Chosen source

• Current resolution and refresh rate

• Device serial number and article number

• Current firmware version and model name

• Current illumination (in percentage)

• Lamp runtime in hours

• Chosen communication method and IP address (if connected)

• Warp status

• Environmental temperature

Image 4-2

4.5 Power off projector

How to Switch off the projector

1. Use the standby button, or the Power On button on the remote control, to switch off the projector.

The projector will switch to READY mode first in order to run through a cool down phase (see “Power mode transitions”, page 36).

2. If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby

ECO", in User Guide) the projector will automatically go to ECO standby mode after a time-out (default 15 minutes).

Some actions like apply a grey test pattern are done during the two minutes of the cool down phase in order to minimize the potential effect of burn-in and increase the projector lifetime.

CAUTION: Never switch off the projector by means of unplugging mains cord or by cut down of mains power.

R5906852-01 F80 series38

Page 39

Getting Started

Barco advises to keep the projector always powered and use the ECO mode for low power consumption.

How to unplug the projector

1. Follow the procedure above to Switch Off the projector.

2. Wait at least 2 minutes prior to unplug the projector by removing the power cord from the AC outlet.

CAUTION: It is very important to wait few minutes before unplug the power cord. If the cool down phase is not adhered, projector lifetime could be degraded.

4.6 Increasing the projector life time

General

Barco propose the following recommendations to increase the projector life time:

• Dimming out the laser output intensity (70%).

• Use the device in regulated temperature area.

• Apply the recommendations describe in the “Operating in 24/7 Mode” chapter if the projector is destined to

be operated continuously 24 hours a day / 7 days a week.

Typical life time of the projector could be up to double if the laser output is dimmed to 75% and if the projector operate in 25°C temp condition.

4.7 Operation in 24/7 Mode

General

When the projector is destined to be operated continuously 24 hours a day / 7 days a week, Barco has a number of recommendations to increase the projector life time:

• Regularly, preferably twice a day if possible, switch off the projector during two minutes by using the

standby button. The power down action will automatically and invisibly trigger a grey test pattern running within the projector. Note: if you really don't want to shut down the projector, an alternative method is select the grey test pattern yourself within the normal “on” mode. This method is not as effective as completely shut down the projector, but may be a more workable alternative.

• Apply moving video content as much as possible, with on average a level of 50% white (long-term use of

extreme black or white content could potentially cause accelerated aging).

4.8 Using the RCU

Pointing to the reflective screen

1. Point the front of the RCU to the reflective screen surface.

R5906852-01 F80 series 39

Page 40

Getting Started

Image 4-3: IR control via reflective screen

Hardwired to the mini jack input

1. Plug one end of the remote cable in the connector on the front side (3,5mm mini jack) of the RCU.

2. Plug the other end in the connector on the communication interface of the projector, labelled ‘Remote

CTRL’(reference 1, Image 4-4).

Image 4-4

Note: Plugging the remote control will switch the broadcast address of the remote control to the default value '0'. This is the only broadcast address that will work when hardwired. If you want to change the broadcast address after disconnecting the remote control, see “Projector Address”, page

41.

Pointing directly to the IR sensor

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector IR sensor.

R5906852-01 F80 series40

Page 41

XIT

TR E

LA N

VO L

45°

Image 4-5: RCU to one of the IR sensors

Getting Started

4.9 Projector Address

Projector address

Address installed in the projector to be individually controlled.

Broadcast address

Projector will always execute the command coming from a RCU programmed with that broadcast address.

4.9.1 Controlling the projector

Why a projector address?

As more than one projector can be installed in a room, each projector should be separately addressable with an RCU or computer. Therefore each projector has its own address.

Set up an individual Projector Address

The set up of a projector address can be done via the software.

Projector controlling

When the address is set, the projector can be controlled now:

• with the RCU: only for addresses between 1 and 31.

Broadcast Address

Every projector has a broadcast (common) address '0' or '1'. The default address is '0'. The choice between '0' and '1' can be selected in the GUI: “System Settings” → “Communication” →“IR Control

“.

R5906852-01 F80 series 41

Page 42

Getting Started

Placing new batteries in the remote control or plugging the remote to a projector via a cable will automatically reset the address back to its default value '0'.

4.10 Quick setup via Direct access

Quick source selection

1. Press the Input button on the remote control or local keypad.

Image 4-6

The Source selection menu opens on the LCD display.

Image 4-7: Input selection

2. Use the arrow keys to select the desired source.

Quick test pattern selection

1. Press the Test pattern button on the remote control or local keypad.

R5906852-01 F80 series42

Page 43

Getting Started

Image 4-8

The Test pattern menu opens on the LCD display.

2. Use the arrow keys to select the desired test pattern.

R5906852-01 F80 series 43

Page 44

Getting Started

R5906852-01 F80 series44

Page 45

Graphic User Interface (GUI)

Overview

•

Overview

• Navigation

• Test Patterns

R5906852-01 F80 series

Page 46

1 4

2 3

3 2 1

Graphic User Interface (GUI)

5.1 Overview

GUI - Main Menu overview

The projector on screen display (OSD) is the primary user interface (UI). From here, you can review and adjust all projector and display settings.

The OSD interface uses tabs to display the main menu. Each main menu contains submenus. The OSD can be disabled by pressing the OSD on/off button.

Image 5-1: Home menu

The projector's software platform uses access levels what each user can do. A standard user has access to all projector functionality. A certified service technician has also access to the service menu. This menu is password protected.

5.2 Navigation

Navigation via the RCU or local keypad

Navigating the OSD can be done using the remote control or the local keypad.

Image 5-2

To start up the menu structure, press MENU (1). Use the arrow keys (Menu Navigation buttons) to navigate to the desired menu item (2). The background

color changes to light blue.

R5906852-01 F80 series46

Page 47

Graphic User Interface (GUI)

Press the Menu Selection button (center key of the arrow keys), also called OK button, to activate that item and to jump one level deeper (3).

Use the numeral keys to enter values, or use the arrow keys to move the bar scale up or down. Press the Back button to go up one level (4).

Image 5-3: Home menu

Remark: a blue slider bar on the right side of the window means that there are more items to show than those currently displayed.

Define values

Menu settings are displayed using check boxes, bar scale sliders, and drop-down lists.

To set a value:

• Press OK to select or deselect a checkbox (turn a function ON or OFF).

• Use the arrow keys to move the bar scale slider up or down on the value line. For a bar scale 0-9, each

step will equal 10% of the total value.

• To enter the value as a direct number, press OK, input the digit(s), and then press OK again to execute

and exit cursor mode e.g. OK 79 OK. Within an input field, use the * button as backspace button to remove an entered digit. Use the # button to enter a dot (.).

Changes to values are implemented dynamically. To enter values with the local keyboard, use the arrow keys to select the first digit, press OK. Select the

second digit and press OK. Continue until all digits are entered. Close the action by selecting the enter (↵) button and press OK. Select the backspace button and press OK to remove the last entered digit.

Menu memory

The OSD menu remembers the last selected sub-item as long as the projector is running. The menu memory is reset when restarting the projector from standby.

5.3 Test Patterns

How to use test patterns

1. In the main menu, select Test Patterns.

Push the Test Patterns button on the RC or on the local keypad.

R5906852-01 F80 series 47

Page 48

Graphic User Interface (GUI)

Image 5-4: Main menu, Test Patterns

2. In the Test Patterns menu, select either Patterns, Internal, or P7 Calibration test patterns.

3. In the chosen submenu, select the desired test pattern from the list.

You can select one of the following Patterns test patterns:

• Refresh

• Native Black

You can select one of the following Internal test patterns:

• Aspect

• ANSI Lumen

• Checker Board

• Focus

• Cross hatch

• Mono scope

• FRHL

• Green

• Focus BW

• Color bars

• Blue

• Red

• White

You can select one of the following P7 Calibration test patterns:

• Native Red

• Native Green

• Native Blue

• Native White

4. To turn the test pattern off, return to the previous menu.

R5906852-01 F80 series48

Page 49

GUI – Source 6

About the Source menu

This menu is used to select, review and configure sources into the projector.

Overview of features

•

Displaying a single source

• Connector Settings

R5906852-01 F80 series

Page 50

GUI – Source

6.1 Displaying a single source

About selecting a source

Before a source can be projected, the source signal must be connected to the source input (s) of the device and a valid synchronization signal must be available along with the source signal on at least one of the input connectors.

How to select?

1. Press Menu to activate the menus and select Source.

Image 6-1: Select Source

2. Press OK.

The Select Source menu is displayed with the actual available sources filled out.

Image 6-2: Input selection

3. Select the desired input.

6.2 Connector Settings

About Connector Settings

The Connector Settings menu allows you to change settings for each input connector of the projector.

By default all options for every connector are set to automatic, together with the native Extended Display Identification Data (EDID).

When entering the menu for each input connector, you can change the following:

• Color Space

• Signal Range

• EDID

How to configure a connector

1. Press Menu to activate the menus and select Source.

R5906852-01 F80 series50

Page 51

Image 6-3: Select Source

2. Press OK.

The Select Source menu is displayed with the actual available sources filled out.

3. Scroll down to the bottom of the list of available sources and select Connector Settings.

GUI – Source

Image 6-4: Source menu, Connector Settings

The available input connectors are displayed.

Image 6-5: Select source

4. Select the desired connector.

The Connector Settings menu for this connector will be displayed.

Image 6-6: Example of connector settings for an HDMI connector

R5906852-01 F80 series 51

Page 52

GUI – Source

5. You can change the following:

• To force a limit on the color space, select one of the available color spaces.

• To force a limit on the used signal range, select one of the available signal ranges.

• To set a video timing other than the one native for the connector, select one of the options under EDID.

Note: You cannot change the EDID for SDI connectors.

R5906852-01 F80 series52

Page 53

GUI – Image 7

Overview of features

•

Setting image levels manually

• Adjusting the sharpness

• Adjusting the gamma correction

• P7 Realcolor

• HDR – Perceptual Quantizer (PQ)

R5906852-01 F80 series

Page 54

GUI – Image

7.1 Setting image levels manually

Purpose

Contrast: Change the contrast of the complete output signal (main and PiP window together) of the projected

image.

Brightness: Change the brightness of the complete output signal (main and PiP window together) of the projected image.

Saturation: Change the saturation of the complete output signal (main and PiP window together) of the projected image.

How to set up Contrast

1. In the main menu, select Image → Contrast.

Image 7-1: Image menu — Contrast

2. Use the ◄ or ► key to change the contrast enhancement until the desired value is reached (adjustable between

0 and 2).

Image 7-2: Contrast slider

3. Use the ▲ or ▼ key to select Saturation or Brightness.

go to Home - Image and select Saturation or Brightness.

How to set up Brightness Level

1. In the main menu, select Image → Brightness.

Image 7-3: Image menu — Brightness

R5906852-01 F80 series54

Page 55

GUI – Image

2. Use the ◄ or ► key to change the brightness until the desired value is reached (adjustable between –1 and 1).

Image 7-4: Brightness slider

3. Use the ▲ or ▼ key to select Contrast or Saturation.

go to Home - Image and select Contrast or Saturation.

How to set up Saturation Level

1. In the main menu, select Image → Saturation.

Image 7-5: Image menu — Saturation

2. Use the ◄ or ► key to change the saturation until the desired value is reached (adjustable between -1 and 1).

Image 7-6: Saturation slider

3. Use the ▲ or ▼ key to select Brightness or Contrast.

go to Home - Image and select Brightness or Contrast.

R5906852-01 F80 series 55

Page 56

GUI – Image

7.2 Adjusting the sharpness

About adjusting the sharpness

The sharpness adjustment amplifies the high frequency components in the picture. This means that by increase the sharpness, the picture will be perceived as sharper, and if decreased, the picture will be perceived as more blurry.

Increasing the sharpness will have the best effect in high contrast images, eg a table with text and borders.

In a natural picture, high sharpness can be perceived as noise, as all details in the picture will be amplified.

Available range: -2 to 8.

Default value: 0

Image 7-7: Effect of sharpness adjust

How to adjust

1. In the main menu, select Image → Advanced → Sharpness.

Image 7-8: Image menu — Sharpness

2. Use the ◄ or ► key to change the sharpness until the desired value is reached.

Image 7-9

R5906852-01 F80 series56

Page 57

GUI – Image

7.3 Adjusting the gamma correction

About gamma correction

Gamma correction is an image quality enhancement function that offers a richer image by brightening the already darker portions of the image without altering the brightness of the brighter portions (contrast feeling enhanced).

How to adjust

1. In the main menu, select Image → Advanced → Gamma.

Image 7-10: Advanced menu – Gamma

2. Use the ◄ or ► key to change the gamma value between 1.0 and 2.8 . The default value is 2,2.

Tip: The slider can be adjusted with a precision of 0.1.

Image 7-11

3. Use the ▲ or ▼ key to select Sharpness or Contrast.

go to Home - Image and select Sharpness or Contrast.

7.4 P7 Realcolor

Purpose

When blending images from multiple projectors, the perceived color coordinates of each projector can be altered to a desired common level, so that the projected colors are identical over all projectors used.

Alternatively, if you are unfamiliar with how adjusting the Colors to a specific setting, there are also a certain number of presets available, which forces the color output to specific color standards.

The selection of the presets will vary, depending on the projector type and on the peripherals installed.

R5906852-01 F80 series 57

Page 58

GUI – Image

How to set custom P7 values

1. In the main menu, select Image → Advanced → P7 Realcolor.

Image 7-12: Advanced menu — P7 Realcolor

The P7 menu is displayed.

Image 7-13: P7 Realcolor menu

2. Select the desired Mode. Choose one of the following custom options:

• Custom RGB: 3–point color configuration.

In RGB mode, the C, M and Y coordinates will be calculated automatically based on the R, G and B coordinates.

• Custom RGBCMY: 6–point color configuration (both RGB and CMY).

In RGBCMY mode, each color can be given a specific coordinate within the measured color triangle.

• Custom WHITE: Configure only the White temperature.

3. Define the coordinates for each available color.

Click on a coordinate value and select the current value. Enter the desired value with the numeric keys.

Note: You can only pick coordinates within the measured color triangle.

4. For Custom White, click on White point and choose one of the following:

• Coordinates: Configure the white point via specific coordinates.

The white point is specified using an x, y coordinate in the CIE 1931 Chart.

• Temperature: Configure the white point via a color temperature slider.

The white point is specified on a Kelvin scale between 3200K and 13000K tracking along the black body curve.

You can reset all coordinates to the default values (to native) by selecting Reset modes to native. Press OK button to reset.

How to choose one of the P7 presets

1. In the main menu, select Image → Advanced → P7 Realcolor.

R5906852-01 F80 series58

Page 59

Image 7-14: Advanced menu — P7 Realcolor

The P7 menu is displayed.

GUI – Image

Image 7-15

Image 7-16: P7 Realcolor menu

2. Choose one of the pre-defined presets:

• Native: Projector native color settings. Default setting

• DCI-P3: Color standard for Cinema.

• EBU: European color standard for broadcasting

• SMPTE-C: American color standard for broadcasting.

• Rec. 709: Color standard for high-definition televisions (HDTV).

Image 7-17: Example of one of the presets: Rec. 709

Note: After choosing one of the presets, you can still alter the values of the coordinates to your own choosing, similarly to how you set custom P7 values. Use Reset to return to the default values of the chosen preset.

R5906852-01 F80 series 59

Page 60

GUI – Image

7.5 HDR – Perceptual Quantizer (PQ)

About PQ

Perceptual Quantizer (PQ) is an electro-optical transfer function (EOTF) that allows for the display of High Dynamic Range (HDR) content with a luminance level of up to 10 000 cd/m² and can be used with the Rec. 2020 color space.

If your provided HDR content has been mastered with PQ (e.g. Dolby Vision or HDR10), you can adapt the luminance on screen to adapt to the provided content.

For optimal display of HDR content, this is just one value that will influence the projected image. When entering the desired screen luminance, take into account the distance of the projector to the screen and the quality of the screen used.

How to set the PQ?

1. In the main menu, select Image → Advanced → PQ.

Image 7-18

The PQ menu is displayed

Image 7-19

2. Select the desired Unit (nits or foot-lambert).

3. Enter the Screen luminance (either in nits or foot-lambert).

R5906852-01 F80 series60

Page 61

GUI – Installation 8

Overview of features

•

Configuring the lens, shift

• Orientation

• Warping

• Blending

• Laser illumination

R5906852-01 F80 series

Page 62

GUI – Installation

8.1 Configuring the lens, shift

What can be done?

The image can be shifted by using the vertical and horizontal lens shift.

Lens shift is only possible when lens shift is calibrated. Please refer to the lens calibration section in System Settings → Lens Calibration menu.

Vertical and Horizontal Shift

1. To change the position of the projected image, select Installation → Lens → Shift.

Image 8-1: Lens menu, Lens shift

2. Use the ▲ or ▼ key to shift the lens (image) in vertical direction.

Use the ◄ or ► key to shift the lens (image) in horizontal direction.

Image 8-2: Shift adjustment

8.2 Orientation

What can be done?

The way of physical installation of the projector can be defined to the projector.

The following installation are possible:

• front/table

• front/ceiling

• rear/table

• rear/ceiling

How to set the correct orientation

1. In the main menu, select Installation → Orientation.

R5906852-01 F80 series62

Page 63

Image 8-3: Installation menu, Orientation

The Orientation menu is displayed.

GUI – Installation

Image 8-4: Orientation menu

2. Use the ▲ or ▼ key to select the desired mounting position and press OK button to activate.

Use the ▲ or ▼ key to select the desired projection position and press OK button to activate.

8.3 Warping

8.3.1 About warping

Overview

Image warping is the process of digitally manipulating an image to compensate for the distortion of the screen. Consequently, it can also be used to generate an image with irregular shape.

While an image can be transformed in various ways, pure warping doesn’t affect the colors.

8.3.2 Warping – On/Off

About warping on/off

By toggling between on and off the warping functionality can be enabled or disabled.

How to toggle

1. In the main menu, select Installation → Warp.

Image 8-5: Installation menu, Warp

R5906852-01 F80 series 63

Page 64

GUI – Installation

The Warp menu is displayed.

Image 8-6

2. In the Warp menu, click Warp to toggle between On and Off.

Image 8-7

Image 8-8

8.3.3 Warping – Screen Size

About (Warp) Screen Size adjustment

If the used source aspect ratio is different than the projector aspect ratio, e. g. source is 16:9 and projector is 16:10, then black bars will be projected. In the example case a black bar on top and bottom of the image will be projected. The warp area contains not only the image information but also the black bars. If we want to position e.g. the active left top corner exactly on the screen using 4 corner warp, then it is very hard to do that as we are moving the black left top corner and we do not have control over the exact position of image left top corner. By moving the outline of the warp screen size to the active image information, the corner points of the warp area are now exactly on the corner points of the active image information and makes warping much easier.

Image 8-9: Warp outline example

R5906852-01 F80 series64

Page 65

How to adjust the image?

1. In the main menu, select Installation → Warp → Screen Size.

Image 8-10: Warp Menu, Screen Size

The Screen Size menu is displayed.

GUI – Installation

Image 8-11: Screen size

2. Select either Screen width or Screen height.

3. Set the new value to shrink either the width or height of the warp outline so that the outline is equal with the

active source.

Tip: A red border will be projected along with the current image. The border is a visual tool, showing the result of the adjusted outline.

Tip: The value can also be entered by the numeric keys on the remote control. Press * to delete existing numbers, and enter the new value by the numeric keys.

4. Click Apply.

8.3.4 Warping – 4 corners adjustment

About 4 Corners adjustment

4 corner adjustment is typically used when the mechanical installation of the projector prevents it from pointing perpendicularly at the screen. For example, you can overshoot the screen and use 4 corner adjustment to pull your projected image corners back into the screen.

Some examples:

R5906852-01 F80 series 65

Page 66

GUI – Installation

Image 8-12: 4 corner adjustment

How to adjust the image?

1. In the main menu, select Installation → Warp → 4 Corners.

Image 8-13: Warp menu, 4 Corners

The 4 Corners menu is displayed.

Image 8-14: 4 Corners Warping

2. To enable 4 Corners warping, make sure the 4 corners slider is set to On.

The slider is enabled when set to the right and when it is colored blue.

3. To set warping on one or more of the four corners, select one of the four corners.

4. Set the desired X and Y coordinates for this corner, using the arrow keys.

Tip: A red border corner will be projected along with the current image. The border is a visual aid, showing the result of the warped corners.

5. Repeat from for each corner, until all corners are warped in the desired position.

To reset the 4 corner adjustments, select Reset and press the OK button.

R5906852-01 F80 series66

Page 67

GUI – Installation

8.3.5 Warping – Bow

About bow adjustment

A bow distortion can be adjusted so that a normal image is displayed. Positive adjustments introduce more outside bow distortion. Negative adjustments introduce more inside bow distortion.

Image 8-15: Bow distortion

Symmetric bow correction

1. In the main menu, select Installation → Warp.

Image 8-16: Installation menu, Warp

2. In the Warp menu, select Bow.

Image 8-17: Warp menu, Bow

A check symbol at the bottom right corner indicates that the bow function is activated.

3. To enable Bow correction, make sure the Bow slider is set to On.

The slider is enabled when set to the right and when it is highlighted blue.

R5906852-01 F80 series 67

Page 68

GUI – Installation

Image 8-18: Symmetric Bow correction.

4. To enable a symmetric adjustment, make sure the Symmetric slider is set to On.

The slider is enabled when set to the right and when it is colored blue.

5. Select the side of the picture to be bow corrected, confirm by pressing enter, and use the arrow keys to adjust

the angle and linearity (length) of the vectors.

The angle is adjusted by the up and down arrows on the remote control, and the linearity is adjusted by the left and right arrows.

The correction will occur symmetrically on each side of the center of the highlighted side.

When corrected with the values in the image above, the picture will occur as shown below.

Repeat this step for all sides of the picture that has to be corrected.

Image 8-19: Symmetric bow correction

Non symmetric bow correction

1. Enter the Bow menu, and disable the symmetric slider.

2. There are now two vectors on each side of the picture that can be adjusted individually. Select each of them,

and adjust angle and linearity (length) individually to obtain the correct correction.

The angle is adjusted by the up and down arrows on the remote control, and the linearity is adjusted by the left and right arrows

R5906852-01 F80 series68

Page 69

Image 8-20: Left vector of the upper side of the picture.

GUI – Installation

Image 8-21: Right vector of the upper side of the picture.

3. When corrected with values in the illustrations above, the picture will occur as shown below. Observe that the

upper side of the picture now has an asymmetric correction.

Image 8-22: Asymmetric bow correction

4. Repeat the step for each side of the picture that must be corrected.

R5906852-01 F80 series 69

Page 70

GUI – Installation

Definition of angle and linearity (length) in the bow warp procedure

Image 8-23

To reset the bow adjustments, select Reset and press the OK button.

8.3.6 Warping – Warp files

About custom Warp Files

Next to setting your specific warp configuration in the GUI, you can also upload or download a custom warp grid in XML format to/from the projector. This is a time-saving option when multiple projectors need an identical Warp configuration.

To upload or download warp files you can use Projector Toolset or Prospector tool to upload/download the warp grid in the format of an XML file. Alternatively, you can contact the “file endpoint” directly via the curl program or some other tool that supports http upload.

For more information on uploading/downloading Warp files using the Projector Toolset, refer to the Projector Toolset user manual.

For more information on uploading/downloading Warp files using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

How to activate an uploaded Warp grid?

1. In the main menu, select Installation → Warp.

Image 8-24: Installation menu, Warp

2. In the Warp menu, select Files.

R5906852-01 F80 series70

Page 71

Image 8-25: Warp menu, Files

The Warp Files menu is displayed.

GUI – Installation

Image 8-26

3. If any custom Warp files are available, select the desired warp file.

Image 8-27

4. Click on the on/off button on top to activate the selected warp file.

R5906852-01 F80 series 71

Page 72

GUI – Installation

Image 8-28

8.3.7 Warping – Latency control in a multi projector setup

Transport latency

The added delay in the image processing chain. The value is the number of lines relative to the output resolution.

Latency

The total time from the first pixel is coming in on an input source, until the first light representing that pixel is visible on the screen. This includes the transport delay. The value is normally given in milliseconds.

Functional description

Every projector in a multi–projector setup will have a different latency. This latency depends on the amount of warp and on the frequency of the projected image. In order to have no visible difference in the overall projected image, the user needs to be able to control the latency of each projector.

The latency value can be read out in the status menu for each individual projector.

How to configure transport delay?

1. Read out and note the latency of each projector in the multi-projector setup. You can find this latency under

Transport delay in the status menu for each projector.

2. Identify the projector with the longest delay.

3. For each projector in the setup, select Installation → Warp in the main menu.

Image 8-29: Installation menu, Warp

4. In the Warp menu, select Transport Delay.

R5906852-01 F80 series72

Page 73

Image 8-30: Warp menu, Transport delay

The Transport menu is displayed.

GUI – Installation

Image 8-31

5. Enter the value either by the arrow keys (one step at a time) or directly by the numeric keys on the remote

control.

6. Enter “Apply” to confirm the value.

7. Repeat this process for every projector in the setup.

8.4 Blending

About Blending

Blending is used in multi channel installation to have a seamless transition between the channels. Image blending gives the appearance of a single view, thus achieving realistic immersion for the majority of wide screen applications.

The principle is that the light intensity in the blend zone from each projector will be adjusted individually, so that the rendering on the screen are perceived as from one projector.

R5906852-01 F80 series 73

Page 74

Picture frame Projector 1

Picture frame Projector 2

Width, Projector 2Width, Projector 1

Overlap / Blend Zone

GUI – Installation

Image 8-32

From the start (mask) position, you can blend zone size per edge (left, top, right, bottom). For each edge there will be a drop-off curve for the blend zone.

8.4.1 Blend & Mask

About masking and blending width or height

Offset is used to clip the image on one or multiple sides (masking). This is used to hide parts of the picture that should not be shown on the screen. For example: if the source is a Windows PC, you can hide the menu bar using this method.

The larger the Mask value, the more the image is masked (by black bar) at the corresponding side. E. g. Top mask of 100 will blank the top 100 lines.

Height or width is used to create a blending zone with a smooth brightness drop off. This is used to compensate for the double brightness in overlap areas. The value is the size of the blended area in pixels.

How to adjust blend zones?

1. In the main menu, select Installation → Blend and Mask → Blend – Mask.

Image 8-33: Blend and Mask menu, Blend – Mask

The Blend – Mask menu is displayed.

R5906852-01 F80 series74

Page 75

GUI – Installation

Image 8-34: Blend & Mask menu

2. To enable blending, put the Enable switch to the right. The color of the switch becomes blue when enabled.

3. To project masking lines on the screen, put the Show lines switch to the right. The color of the switch

becomes blue when enabled.

4. Determine the start position of the mask (1) for the masking height and width, together with the desired size of

the mask (2) to determine the width of the masked area.

When the blending lines are activated, you will get a visual indication of the screen of the installed blending area.

Image 8-35

1 Start position (mask) 2 Blending width

5. Select one of the four starting positions values with the arrow keys and confirm.

6. Use the arrow keys or remote digits to change the value of the mask and confirm.

7. Repeat this process for the desired width/height value.

8. Repeat this process for all other desired sides.

R5906852-01 F80 series 75

Page 76

GUI – Installation

Do not forget to disable the Show lines button after you achieved the desired blend zone.

Example of the use of blending

When projecting an image with 2 or more projectors, there is always an small overlap that should be corrected by using the blending function.

In order to obtain a satisfying result for the Blend function, the overlap / mask zone are recommended to be at least 10% of the picture width.

The basic principle is that the overlap setup in the source shall correspond with the mask width setup for the projector. That means that if the overlap zone for the source is set to 500 pixels, the width of the mask zone for the projector also must be set to 500 pixels.

First step is to align the image from the projectors as accurate as possible in a mechanical way, meaning without any optical corrections. At the same time, establish an overlap in the pictures between the two screens.

Then adjust the remaining irregularities by using the shift and warp features in the projectors to obtain the last fine tuning of the alignment.

Enable blending and activate Show lines.

First set the mask width for the right edge of the first projector. Enter a width value equal to the overlap area (width1).

Repeat for the left edge of the second projector.

Adjust the offset to cut the image on each side (masking).

Image 8-36: Set up for projector 1

R5906852-01 F80 series76

Page 77

Image 8-37: Set up for projector 2

Picture Left Picture RightBlend Zone

GUI – Installation

8.4.2 Black level adjustment

About adjusting the black level

The purpose of the black level adjustment is to align the black levels in the overlapped regions with the black levels in the other regions.

This is needed because the black levels will be brighter in the blend zones, since multiple projectors will project on the same screen area.

The size of the black level area is calculated automatically from the blend zones. This is done by using the start position and size of each edge of the blend and adding an additional size of 8 pixels to reduce the effect known as "sea of mirrors".

You can also specify the offsets manually by turning off the automatic calculation. The black level value is adjusted in a 8 bit resolution from 0 to 255.

The following figure shows how this occurs in a side by side configuration without any correction of the black level.

Image 8-38

How to adjust the black level manually

1. In the main menu, select Installation → Blend and Mask → Black Level.

R5906852-01 F80 series 77

Page 78

GUI – Installation

Image 8-39: Blend and Mask menu — Black Level

The Black Level menu is displayed.

Image 8-40: Black Level menu

2. Enable the Black level button. If you want a visual aid, enable the Show lines button as well.

3. Move the cursor to the side where the overlapped area occurs (left/right/top/bottom) and press enter.

4. Adjust the level with the arrow keys and press enter when the desired black level zone is reached.

enter the black level value with the numeric keys in the remote control.

5. Move the cursor to “Level”, press enter and adjust this level until the black level equals the level in the blend

zone.

This value can also be entered by the numeric keys on the remote control.

6. Repeat the same procedure for any other projector connected to this projector, but on the opposite side.

Note: Do not forget to disable the Show lines button after you achieved the desired blend zone.

8.4.3 Black Level Files

About custom Black Level Files

Next to setting your specific Black Level Adjustment in the GUI, you can also upload or download a custom Black Level adjustment file in png, jpeg or tiff format to/from the projector.

To upload or download Black Level adjustment files you can use Projector Toolset or upload/download the Black Level adjustment file in the format of an XML file. Alternatively, you can contact the “file endpoint” directly via the curl program or some other tool that supports http upload.

For more information on uploading/downloading Black Level files using the Projector Toolset, refer to the Projector Toolset user manual.

For more information on uploading/downloading Black Level files using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

R5906852-01 F80 series78

Page 79

How to activate an uploaded Black Level adjustment file?

1. In the main menu, select Installation → Blend and Mask → Black Level Files.

Image 8-41: Blend and Mask menu, Black Level Files

The Black Level Files menu is displayed.

GUI – Installation

Image 8-42

2. If any custom Black Level adjustment files are available, select the desired file.

Image 8-43

3. Click on the on/off button on top to activate the selected Black Level adjustment file.

8.4.4 Blend Files

About custom Blend Files

Next to setting your specific Blending configuration in the GUI, you can also upload or download a custom Blend configuration file in png, jpg or tiff format to/from the projector. This is a timesaving option when multiple projectors need an identical blending configuration.

To upload or download Blend configuration files you can use Projector Toolset or upload/download the Blend configuration file in the format of an xml file. Alternatively, you can contact the “file endpoint” directly via the curl program or some other tool that supports http upload.

For more information on uploading/downloading Blend files using the Projector Toolset, refer to the Projector Toolset user manual.

R5906852-01 F80 series 79

Page 80

GUI – Installation

For more information on uploading/downloading Blend files using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

How to activate an uploaded Blend configuration file?

1. In the main menu, select Installation → Blend and Mask → Blend Files.

Image 8-44: Blend menu, Blend Files

The Blend Files menu is displayed.

Image 8-45

2. If any custom Blend files are available, select the desired file.

Image 8-46

3. Click on the on/off button on top to activate the selected Blend file.

8.5 Laser illumination

What can be done?

Within a certain power mode, the light output of the light source can be reduced by reducing the laser power.

Alternatively, you can enable CLO mode (Constant light output) for a constant light output over a longer period of time.

R5906852-01 F80 series80

Page 81

GUI – Installation

About CLO mode

All light sources naturally decrease their intensity over time. In order to prevent a decreasing output in a multiprojector setup, you can activate CLO mode to make sure that the light output remains constant.

CLO mode will ensure that the projector regulates its illumination power to maintain the same level of output light during the lifetime of the light source. This requires that the light source power is not set to 100% from the start, but to a lower value. The lower this value is set, the longer the projector will be able to maintain the output level.

How to reduce the power

1. In the main menu, select Installation → Illumination → Power.

Image 8-47: Illumination menu, Power

The actual power setting is indicated at the bottom of the Power button.

2. Use the Slider to change the power value.

Image 8-48: Laser power adjustment

3. If you want CLO mode to be active, click Enable underneath Constant light output.

R5906852-01 F80 series 81

Page 82

GUI – Installation

R5906852-01 F80 series82

Page 83

GUI – System

Settings

Overview of features

•

Communication

• Themes

• Standby ECO

• Service Menu

• Reset

R5906852-01 F80 series

Page 84

GUI – System Settings

9.1 Communication

About a network connection

Network connection is required to communicate with the projector via LAN or Internet. The setup could be done manually (set address, subnet mask and default gateway according to network specification), or automatically assign (DHCP).

9.1.1 Introduction to a Network connection

DHCP

Dynamic host configuration protocol. DHCP is a communications protocol that lets network administrators manage centrally and automate the assignment of IP addresses in an organization's network. Using the Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network.

Internet Protocol. The network layer of TCP/IP. Required for communication with the internet.

Subnet mask

A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network.

Default Gateway

A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may need a gateway to connect it to a wide area network (WAN) or to the Internet.

MAC address

Media Access Control address. Unique hardware number, used in combination with the IP-address to connect to the network (LAN or WAN).

What should be set up for an Ethernet address?

Two ways can be used to assign an address:

• use the Automatic setting so that an automatic address will be assigned.

• Assign manually an IP address, Net-mask (subnet-mask), (default) gateway address.

- Set the IP-Address field to the desired value. This must NOT be 0.0.0.0 for static IP-Address

assignment. The IP address identifies a projector's location on the network in the same way a street address identifies a house on a city block. Just as a street address must identify a unique residence, an IP address must be globally unique and have a uniform format.

- Set the Subnet-Mask as appropriate for the local subnet.

- Set the Default-Gateway to the IP-Address of the local router (MUST be on the local subnet!) on the

same network as this projector that is used to forward traffic to destinations beyond the local network. This must not be 0.0.0.0. If there is no router on the projector's local subnet then just set this field to any IP-Address on the subnet.

9.1.2 Wired IP address set up

How to automatically set up the IP address

1. In the main menu, select System Settings → Communication → LAN.

R5906852-01 F80 series84

Page 85

Image 9-1: Communication menu, LAN

The LAN menu is displayed

GUI – System Settings

Image 9-2: LAN menu

2. To enable Automatic, put the switch to the right. The color of the switch becomes blue.

An automatic IP is assigned.

When connected, it is indicated with the connection symbol and the indication Connected.

3. Select APPLY and click OK.

How to manually set up the IP address

1. In the main menu, select System Settings → Communication → LAN.

Image 9-3: Communication menu, LAN

The LAN menu is displayed

Image 9-4: LAN menu

2. Disable Automatic. Put the switch to the left. The switch becomes gray.

R5906852-01 F80 series 85

Page 86

GUI – System Settings

3. Use the ▲ or ▼ key to select Address and press OK button to activate the input box.

4. Use the ▲ or ▼ key to change the selected character.

Use the ◄ or ► key to select another character.

Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatically.

5. Repeat steps 4 and 5 for the Subnet mask and Default Gateway.

6. Select APPLY and click OK to confirm all changes.

When the connection is established, it is indicated with the connection symbol and the indication Connected.

9.2 Themes

About Themes

Themes are used to apply a predefined functionality to the OSD display. There are two options: light (default) or dark.

How to select a different interface theme

1. In the main menu, select System Settings →Themes.

Image 9-5: System Settings Menu — Themes.

2. In the themes menu, select the desired Theme.

You can choose one of the following: Light, or Dark.

9.3 Standby ECO

About Standby ECO

When the ECO mode is enabled, the projector will automatically go to ECO standby mode after a time-out (default 15 minutes). All electronics (including fans, pumps, ...) go down except for a very small wake-up controller. See section dedicated to the Power Mode transitions for further details.

How to enable the ECO mode

1. In the main menu, select System Settings →Standby ECO.

Image 9-6: System Settings Menu — Standby ECO

R5906852-01 F80 series86

Page 87

GUI – System Settings

2. To enable the ECO mode, make sure the slider is set to On. The slider is enabled when set to the right and

when it is colored blue.

How to disable the ECO mode

1. In the main menu, select System Settings →Standby ECO.

Image 9-7

2. To disable the ECO mode, make sure the slider is set to Off. The slider is disabled when set to the left and

when it becomes grey.

9.4 Service Menu

About the service menu

The service menu can only be entered with a Service code.

Image 9-8: Service code

If you have a service code, select Service code with the arrow keys and click OK to enter the entry mode. Enter the code with the numeric keys and select OK and click OK on to confirm. Otherwise select DISCARD and click OK to return to the System Settings menu.

Overview

•

Service – Color Wheel

• Service – Color

• Service – Statistics

• Lens Calibration

• Service – Pixel Shift

9.4.1 Service – Color Wheel

About Color Wheel

F80 is equip with only one Color Wheel which is controlled by the software. However, via the service menu, a Slider makes possible a fine-tuning for variation on the Color Wheel.

How to fine-tuning

1. In the main menu, System Settings → Service.

R5906852-01 F80 series 87

Page 88

GUI – System Settings

Image 9-9

2. Enter the service code.

3. In the Service menu, select Color Wheel.

Image 9-10

The Color Wheel menu will be displayed.

Image 9-11

4. Change the values to the desired position.

9.4.2 Service – Color

CAUTION: The native colors have been measured and set during factory production. Do not

change them, unless parts of the optical path have been replaced due to servicing. If you need to change the native colors on the device, make sure to also perform a P7 calibration, using the Projector Toolset and a chroma meter. For more info on P7 calibration, refer to the Projector Toolset Reference guide.

How to adjust the P7 native settings

1. In the main menu, System Settings → Service.

Image 9-12

2. Enter the service code.

3. In the Service menu, select Color.

R5906852-01 F80 series88

Page 89

Image 9-13

The Color menu will be displayed.

GUI – System Settings

Image 9-14

4. Select the desired value to change and confirm.

5. Change the values to the desired position, taking into account the color gamut values.

6. Select APPLY and click OK.

9.4.3 Service – Statistics

What can be seen?

The statistics screen shows the general information about the projector.

The following items will be displayed:

• Laser runtime

• Laser Strikes

• Projector Runtime

• System time

• Current Uptime

• Pump Runtime

How to display the statistics

1. In the main menu, System Settings → Service.

Image 9-15

2. Enter the service code.

3. In the Service menu, select Statistics.

R5906852-01 F80 series 89

Page 90

GUI – System Settings

Image 9-16

The Statistics will be displayed.

Image 9-17

9.4.4 Lens Calibration

Lens calibration is a time consuming operation.

How to calibrate

1. In the main menu, System Settings → Service.

Image 9-18

2. Enter the service code.

3. In the Service menu, select Lens Calibration.

Image 9-19: System Settings menu — Lens Calibration

The Lens Calibration menu is displayed.

R5906852-01 F80 series90

Page 91

GUI – System Settings

Image 9-20: Lens Calibration menu

4. In the Lens Calibration menu, select the desired calibration action and click OK.

You can select one of the following functions:

• Horizontal shift

• Vertical shift

• Focus

• Zoom

The text Calibration in progress will be displayed next to selected function until the calibration is completed.

When an error is detected, the message Calibration Error is displayed next to function.

9.4.5 Service – Pixel Shift

About Pixel Shift

This setting allows production to fine tune the wobulator/XPR until the marker is in the ‘bullseye’. During the settings, the repetitive on screen pattern ‘CROSS HATCH’ must be displayed. The maintenance person has to align the both following images with the sliders available in this menu.

Image 9-21

How to fine-tuning

1. In the main menu, System Settings → Service.

Image 9-22

2. Enter the service code.

3. In the Service menu, select Pixel Shift.

R5906852-01 F80 series 91

Page 92

GUI – System Settings

Image 9-23

The Pixel Shift menu will be displayed.

Image 9-24

4. Change the values to the desired position.

• Gain: is the amplitude of the waveform which is sent into the Wobulator. Default value: 0.65

• Resonance (frequency) : if frequency is 0Hz the wobulator is of. High frequency means high noise. Default

value: 227Hz

9.5 Reset

What can be done?

All settings and values on the projector can be reset to its default values. This can be done for one or more settings separately, or all settings together (factory reset).

Default settings

The following settings are default settings:

Setting Default value

UserInterface Theme Light

Network Communication LAN, Automatic settings

System Eco Mode (if applicable) Available

Ready Timeout auto

Screen Screen luminance - Unit nits

Optics High Contrast Off

Illumination Power 100%

ImageConnector Color Space auto

Signal Range auto

ImageResolution Output Resolution (if applicable) 4K UHD

ImageWarp Screen size 5120x3200 / 2560x1600

4 corner Bow

Warp files Disabled, no files selected

R5906852-01 F80 series92

Warp off, no warp

Page 93

GUI – System Settings

Setting Default value

ImageBlend Blend/Mask size

Black Level

Black Level Files Blend Files

ImageRealColor P7 Realcolor all set to native

ImageStereo Sync delay 0 µs

Swap eye Off

Dark time lowest value available

ImageDisplay Display mode AutoStereo

ImageOrientation Orientation Table, Front

ImageSource Source files Standard

ImageFeatures Contrast mid value

Brightness mid value

Saturation mid value

Sharpness mid value

Gamma mid value

Cropping (if applicable) Off

Aspect Ratio (if applicable) 16:9

disabled, all value to zero

Disabled, no files selected

How to reset all projector settings

1. In the main menu, select System Settings → Reset.

2. In the Reset menu, select RESET ALL and click OK.

How to reset one or more projector settings

1. In the main menu, select System Settings → Reset.

Image 9-25: System Settings menu, Reset

The Reset menu is displayed.

R5906852-01 F80 series 93

Page 94

GUI – System Settings

Image 9-26: Reset menu

2. Navigate to the checkbox next to the settings that need to be reset and press OK.

Multiple selections are possible.

3. Select RESET and press OK to reset all selected settings.

R5906852-01 F80 series94

Page 95

Status menu 10

This is a status menu only. No changes can be made to settings from this menu.

Overview

•

Status menu overview

R5906852-01 F80 series

Page 96

Status menu

10.1 Status menu overview

Status menu

While in the main menu, press Status.

Image 10-1: Status Menu enter

Image 10-2: Status overview

Image 10-3: Status overview (Menu scrolled down)..

R5906852-01 F80 series96

Page 97

Image 10-4: Example of active functions enabled.

Source status

Displays active source information

Product

Displays active product information:

• Article number: Projector article / part number

• Serial number: Projector serial number

• Firmware: Projector software package version

• Model name: Projector model name

Status menu

Illumination

Shows the used light source power (in %) and runtime.

Communication

Lists the projector network address, the remote control broadcast address and the remote control projector address.

Warp

Displays the Warp status and type of warp used

Blend

Displays the Warp status and type of Blend used

Environment

Shows the ambient temperature.

Display

Shows display settings

Active Functions

Shows the active function enabled.

R5906852-01 F80 series 97

Page 98

Status menu

R5906852-01 F80 series98

Page 99

Maintenance 11

About this chapter

This chapter contains general maintenance procedures.

Overview

•

Cleaning the lens

• Cleaning the exterior of the projector

• Filters

R5906852-01 F80 series

Page 100

Maintenance

11.1 Cleaning the lens

To minimize the possibility of damage to optical coatings, or scratches to lens surfaces follow the cleaning procedure as described here precisely.

Required tools

• Compressed air.

• Clean Toraysee® cloth or any micro fiber lens cleaning cloth.

• Clean cotton cloth.

Required parts

Lens cleaner (e.g. Carl Zeiss lens cleaner or Purasol® or any water-based lens cleaner)

How to clean the lens?

1. Blow off dust with clean compressed air (or pressurized air cans1) .

2. Clean with lens cleaner together with a clean lens cleaning cloth to remove the dust and contamination. Use

big wipes in one single direction.

Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the

coating.

3. Use a dry lens cleaning cloth to remove left liquid or stripes. Polish with small circles.

4. If there are still fingerprints on the surface, wipe them off with lens cleaner together with a clean lens cleaning

cloth. Polish again with a dry one.

If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

11.2 Cleaning the exterior of the projector

How to clean the exterior of the projector ?

1. Switch off the projector and unplug the projector from the mains power net.

2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly

dampened with a mild detergent solution.

11.3 Filters

General info regarding Air intake and filters.

The F80 is shipped without any filters. The air intake is just protected by a mesh. This mesh has to be vacuum cleaned occasionally when needed. There is no specific interval for this operation.

1: Pressurized air cans are not efficient if there is too much dust on the surface, the pressure is too low

R5906852-01 F80 series100

Barco F80, F80-Q7, F80-4K7, F80-4K9, F80-Ultra User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual