Barco F70-4K8 User Manual

F70 Series

User Manual

601–426/02 18/04/2018

Barco Fredrikstad AS Habornveien 53, N-1630 Gamle Fredrikstad, Norway Phone: +47 6930 4550 Fax: +47 6930 4580 Support: Support.fre@barco.com Visit us at the web: www.barco.com

Printed in Norway

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and ﬁ tness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time w ithout notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically m ade to the information in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site w

ttps://www.barco.com/en/signin.

ww.barco.com or from the secured Barco web site

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable p rotection aga inst harmful interference when the equipm ent is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may c ause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user ’s authority to operate the equipment

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names me ntioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.

Turkey RoHS compliance

Türkiye Cumhu riyeti: AEEE Y önetmeli ğine Uygundur.

[Republic of Turkey: In conformity with the WEEE Regulation]

Disposal Information

Waste Electrical and E lectronic Equipment

This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated co llection point for t he recycling of waste electrical and electronic equipm ent. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

For more information about r ecycling of this product, please contact your local city ofﬁce or your municipal waste disposal service.

For details, please visit the Barco website at: h

ttp://www.barco.com/en/AboutBarco/weee

Disposal of batteries in the product

This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately from

municipal waste.

If the battery contains more than the s peciﬁed values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol.

By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health.

Guarantee and Compensation

Barco provides a guara ntee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. O n receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justiﬁed notice of complaint, Barco can repair the fault o r p rovide a replacement at its own discretion w ithin an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser ca n demand a reduction in the purchase pr ice or cancellation of the contract. All other claims, in particular tho se relating to com pensa tion for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is n ot proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out m odiﬁcations or repairs on goods delivered by B arco, or if the goods ar e handled incorrectly, in particular if the systems are o perated incorrectly or if, after the transfer of risk s, the the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are sy stem failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subjec t to the guarantee provided by Barco either.

The environmental conditions as well as t he servicing and maintenance regulations speciﬁed in this manual must be com plied with by the customer.

goods are subject to inﬂuences not agreed upon in

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be r ecorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Software License Agreement

You should carefully read the following terms and conditions before using this software. Your use of this software indicates your acceptance of this license agreement and warranty.

Terms and Conditions:

1. No redistribution of the software is allowed.

2. Reverse-Engineering. You may not reverse engineer, decompile, disassemble or alter this s oftware product.

Disclaimer of Warranty:

This software and the accompanying ﬁles are sold “as is” and without warranties as to performance or merchantability or any other war ranties whether expressed or implied. In no event shall B arco be interruption or other pecuniary loss arising directly or indirectly. Any liability of the s eller will be exclusively limited to replacement of the product or refund of purchase price.

liable for damage of any kind, loss of data, loss of proﬁts, business

Table of contents

TABLE OF CONTENTS

1. Safety................................................................................................................. 5

1.1 General considerations ............................................................................................................... 5

1.2 Important safety instructions ......................................................................................................... 7

1.3 Projector Hazard Distances .......................................................................................................... 9

1.4 High Brightness Precautions......................................................................................................... 9

1.5 Hazard Distance for fully closed projection system ................................................................................ 11

1.6 HD in function of the lens Throw Ratio (TR)........................................................................................12

1.7 Safety symbols ......................................................................................................................13

1.8 RoHS compliance ...................................................................................................................15

1.9 Taiwan RoHS compliance...........................................................................................................17

1.10 Contact information..................................................................................................................18

1.11 Product Info . . ........................................................................................................................ 18

1.12 Statement ............................................................................................................................19

2. Getting to know the projector. ................. ................ ................ ................ ................ .21

2.1 Main Components . . .................................................................................................................21

2.2 Service and Maintenance . ..........................................................................................................22

2.3 LED Status Light..................................................................................................................... 22

2.4 Power on / Standby button backlight indications ...................................................................................22

2.5 LCD panel . .. ........................................................................................................................ 23

2.6 Local keypad......................................................................................................................... 23

2.7 Remote Control...................................................................................................................... 24

2.7.1 Remote control,Battery installation ..........................................................................................24

2.7.2 Remote control,protocol setup...............................................................................................25

2.7.3 Functionality overview ........................................................................................................ 26

2.7.4 Remote control,on/offbutton.................................................................................................26

2.7.5 Enable / Disable Remote Control ............................................................................................27

2.7.6 Wired RC connection ......................................................................................................... 27

2.8 Projector Address....................................................................................................................27

2.8.1 Controlling the projector ......................................................................................................27

2.9 Connector panel ..................................................................................................................... 28

2.10 Color Wheels ........................................................................................................................29

2.11 Optional Accessories ................................................................................................................29

3. Lenses.................... ................ ................ ................ ................ ................ ...........31

3.1 Approved Lenses . .. .................................................................................................................31

3.2 Lens range . . . ........................................................................................................................ 31

3.3 Replace a lens.......................................................................................................................33

3.4 Lens shift............................................................................................................................. 35

3.5 Adjust zoom and focus..............................................................................................................35

3.6 Adjust Iris ............................................................................................................................35

4. Physical Installation ..............................................................................................37

4.1 Installation Process..................................................................................................................37

4.2 Installation conditions ............................................................................................................... 37

4.3 Initial inspection......................................................................................................................38

4.4 Positioning the projector............................................................................................................. 39

4.5 Mounting the projector, general considerations . ...................................................................................39

4.6 Projector safe attachmentpoints....................................................................................................41

4.7 Throw distance ......................................................................................................................42

4.8 Scheimpﬂug (Boresight) adjustment ................................................................................................44

4.9 Scheimpﬂug adjustment procedure .................................................................................................45

5. Getting started .......... ................ ................ ................ ................ .................. .........47

5.1 Projector source and control connections . . ........................................................................................47

5.1.1 Making connections . . ......................................................................................................... 47

5.1.2 Connector speciﬁcations...................................................................................................... 47

5.1.2.1 DVI-I ....................................................................................................................47

5.1.2.2 Display Port 1.2 ........................................................................................................48

5.1.2.3 HDMI 2.0................................................................................................................48

5.1.2.4 3G-SDI..................................................................................................................49

5.1.2.5 HDBase T...............................................................................................................49

5.1.3 Control interfaces.............................................................................................................49

5.1.3.1 RS-232..................................................................................................................50

5.1.3.2 LAN/Ethernet...........................................................................................................50

5.1.3.3 USB-A port .............................................................................................................50

5.2 Power upthe projector ..............................................................................................................50

5.3 Power down the projector ........................................................................................................... 50

5.4 Power mode transitions .............................................................................................................51

5.4.1 General ........................................................................................................................51

5.4.2 Power onprojector............................................................................................................ 51

5.4.3 Going from READY to ON....................................................................................................51

5.4.4 Going from ON to READY....................................................................................................52

601–426 F70 SERIES 18/04/2018

Table of contents

5.4.5 Going from READY to ECO standby......................................................................................... 52

5.4.6 Going from ECO to ON.......................................................................................................52

5.4.7 Wake On LAN (WOL).........................................................................................................52

5.5 Power modes ........................................................................................................................52

5.6 Customize projector settings ........................................................................................................52

5.7 User interface........................................................................................................................52

5.7.1 On Screen Display (OSD) ....................................................................................................53

6. Source menu ...... ................ ................ ................ ................ ................ ................ .55

6.1 Connector selection .................................................................................................................55

6.2 Connector Settings ..................................................................................................................55

6.3 Using Dual inputs....................................................................................................................57

7. Image menu ................... ................ ................ ................ ................ ................ .....59

7.1 Contrast..............................................................................................................................59

7.2 Brightness ........................................................................................................................... 60

7.3 Saturation ............................................................................................................................ 60

7.4 Sharpness . . . ........................................................................................................................61

7.5 Gamma Adjustment .................................................................................................................61

7.6 Advanced image adjustments ....................................................................................................... 62

7.6.1 P7 Realcolor .................................................................................................................. 62

7.6.2 Editthe RealColor presets. ...................................................................................................64

7.6.3 Output Resolution 4K .........................................................................................................65

7.6.4 Smear Reduction ............................................................................................................. 65

7.6.5 Brilliantcolor ...................................................................................................................66

7.6.6 HDR – Perceptual Quantizer (PQ) ........................................................................................... 68

7.6.7 HDR Status....................................................................................................................68

8. Installation menu ..................................................................................................71

8.1 IR / Night vision functionality ........................................................................................................71

8.2 Lens . . ................................................................................................................................73

8.3 Orientation...........................................................................................................................73

8.4 Warping..............................................................................................................................74

8.4.1 About Warping ................................................................................................................74

8.4.2 Warping – On/Off .............................................................................................................75

8.4.3 Warping – Screen Size .......................................................................................................76

8.4.4 Warp – 4 Corners adjustment ................................................................................................ 77

8.4.5 Warping – Bow................................................................................................................78

8.4.6 Warping – Warp ﬁles..........................................................................................................82

8.4.7 Warping – Latency control in a multi projector setup ........................................................................83

8.5 Blending..............................................................................................................................85

8.5.1 Basic Blend ................................................................................................................... 85

8.5.2 Set up the system.............................................................................................................85

8.5.3 Adjustment Procedure ........................................................................................................85

8.5.4 Black LevelAdjustment.......................................................................................................86

8.5.5 Black LevelFiles ..............................................................................................................88

8.5.6 Blend Files ....................................................................................................................89

8.6 Illumination...........................................................................................................................90

8.7 CLO – constant light output.........................................................................................................90

8.8 Display Setup........................................................................................................................91

9. System settings menu............................................................................................93

9.1 Communication ...................................................................................................................... 93

9.2 Apply a menu theme ................................................................................................................93

9.3 Standby ECO ........................................................................................................................94

9.4 Service ...............................................................................................................................94

9.5 Reset.................................................................................................................................94

9.6 Lens Features .......................................................................................................................96

9.7 Controlling thebacklight of the LCD Display .......................................................................................96

10. Status menu ............. ................ ................ ................ ................ ................ ...........99

10.1 Status menu overview ...............................................................................................................99

11. 3D ... ................ ................ ................ ................ ................ ................ ............... 103

11.1 Setup 3D mode. ....................................................................................................................103

12. User Maintenance ............................................................................................... 105

12.1 Update Projector Firmware. ........................................................................................................105

13. Cleaning the projector............... ................ ................ ................ ................ ........... 107

13.1 Projector lenses ....................................................................................................................107

13.2 Projector cabinet....................................................................................................................107

13.3 Filters ...............................................................................................................................107

14. Technical Speciﬁcations ............ ................ ................ ................ ................ ........... 109

14.1 F70 — 4K6C........................................................................................................................109

14.2 F70 — W6 ..........................................................................................................................110

601–426 F70 SERIES 18/04/2018

Table of contents

14.3 FS70 — 4K6 ........................................................................................................................111

14.4 FS70 — W6.........................................................................................................................112

601–426 F70 SERIES 18/04/2018

Table of contents

4 601–426 F70 SERIES 18/04/2018

1. SAFETY

About this chapter

Read this c hapter thoroughly before attempting to install or operate the projector.

To prevent personal injury to users or physical damage to the projector while installing and using your projector, ensure that you understand and follow all safety guidelines, instructions and warnings included in this chapter and this manual.

Clariﬁcation of the term F70 / F90 series used in this document

Use in this document of the term, F70 / F90 series, means that the content is applicable for the followi

• F90–W13WUXGA

• F90–4K13 4KUHD/WQXGA

•F70—4K6

•F70—W6

Deﬁning the GP6 platform

The F90 series products in general, are all p roducts within the Barco GP6 Platform.

Deﬁning the GP7 platform

The F70 series products in general, ar e all products within the Barco GP7 Platform

Overview

ng products:

1. Safety

• General considerations

• Important safety instructions

• Projector Hazard Distances

• High B rightness Precautions

• Hazard Distance for fully closed projection system

• HD in function of the lens Throw Ratio (TR)

• Safety sym bols

• RoHS compliance

• Taiwan RoHS compliance

• Contact information

• Product Info

• Statement

1.1 General considerations

Notice on optical radiation F90 Series

• The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. For Northern America, the projector is class 3R laser product up to throw ratio 2.33. The projector conforms with IEC 6 laser products under 21 CFR 1040, except with respect to those characteristics authorized by Variance Number 2016–V-0144 effective March 6, 2017 Do no t stare into Beam.

• This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk Group 3 (RG3) when an interchangeable lens with throw ratio greater than 3.15 is installed. For Northern America, installation requirements according to Risk group 3 (RG3) must be followed when interchangeable lens with throw ratio greater than 2.33 is installed. Refer to the manual for the lens list and throw ratio before operation. Such combination of projec tor and lens are intended for professional use only, and are not intended for consumer use.

• For RG3, no direct exposure to the beam shall be permitted. For RG3, operators s hall control access to the beam within the hazard distance or install the product at a height that will p revent eye exposure within the hazard distance.

• This projector has two (2) built-in Class 4 laser clusters. Disassembly or modiﬁcation is very dangerous and should never be attempted.

• Any operation or adjustment not speciﬁcally instructed by t sure.

• Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.

he user ’s guide creates the risk of hazardous laser radiation expo-

0825–1:2007, and with performance standards for

601–426 F70 SERIES 18/04/2018

1. Safety

Notice on optical radiation F70 Series

• The projector is Class 1 laser product that conforms with IEC EN 60825-1:2014. For Northern America, the projector is class 3R las er product up to throw ratio 2.5. The projector conforms with IEC 60825–1:2007, and with performance standards for laser products under 21 CFR 1040, except with respect to those characteristics authorized by Variance Number 2016–V-0144 effective March 6, 2017 Do no t stare into Beam.

• This projector is Risk Group 2 (RG2) according to IEC EN 62471-5. This projector may become Risk Group 3 (RG3) when an interchangeable lens with throw ratio greater than 4. Northern America, installation requirements according to Risk group 3 (RG3) must be followed w hen interchangeable lens with throw ratio greater than 2.5 is installed. Refer to the manual for the lens list and throw ratio before operation. Such combination of projec tor and lens are intended for professional use only, and are not intended for consumer use.

• This projector has one (1) built-in Class 4 laser clusters. Disassembly or modiﬁcation is very dangerous and should never be attempted.

• Any operation or adjustment not speciﬁcally instructed by the user’s guide creates the risk of hazardous laser radiation exposure.

• Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.

7 is installed. For

General safety instructions

• This product contains no user serviceable parts except the Color Wheel in F90 projectors.

When projector becomes RG3, change of color wheel must only be performed by authorized service personnel.

Attempts to modify/replace mechanics or elec tronics inside the housing or compartments will violate any warranties and may be hazardous. Do not remove/replace any other parts than the Color Wheel. Other parts, service personnel only – Warranty void if Removed. Follow the instructions in the User Guide to replace the Color Wheel.

• Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.

• Not following the prescribed control, adjustment or operation procedure may ca

• Before operating this equipment please read this manual thoroughly and retain it for future reference.

• Installation and preliminary adjustments should be performed by properly trained and qualiﬁed personnel.

• All warnings on the projector and in the documenta tion manuals m ust be adhered to.

• All instructions for operating and use of this equipment must be followed precisely.

• All local installation codes should be adhered to.

use damage by the exposure of laser radiation.

Notice on safety

This equipment is built in accorda nce with the requirements of the international safety standards IEC 60950-1, as basis for National safety regulation world wide. The safety standard covers information technology equipment including electrical business equipment intended to operate in “normal” environments (ofﬁces and homes). This safety standard imposes important requirements o n the use of safety critical components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of ﬁre. Simulated single fault condition testing reduce the risk of hazards and contribute to ensure the safety of the equipm ent to the user even when the equipment’s normal operation fails.

Users deﬁnition

Throughout this manual, the term SERVICE PERSONNE L refers to Barco authorized persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELEC TRIC and ELEC TRONIC CIRCUITRY and HIGH BRIGHTNESS PROJ ECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers to any person other than SERVICE P ERS ON NEL.

When installing an interchangeable lens with a throw ratio that m akes the projector become an RG3 unit, (See chapter “Approved lenses” in the User m anual), r efer to chapter

Refer to the us er manual for the lens list and hazard distance before operation. Such combination of projector and lens are intended for professional use only, and are not intended for consumer use.

FOR PRO FESS IONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED PERSONNEL familiar with potential hazards associated with high intensity light beams.

"High Brightness Precautions", page 9 for information regarding precautions.

601–426 F70 SERIES 18/04/2018

1.2 Important safety instructions

To prevent the risk of electrical shock

• This product should be operated from a mono phase AC power source.

• This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the outlet, co ntact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.

• Do not allow anything to rest on the power c ord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• Use only the power cord supplied w ith your device or original replacement cords. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the device. F or a replacement power cord, contact your dealer.

• Do not operate the projector with a damaged cord. Replace the cord. Do not operate the projector if the projector has been dropped or dam aged - until it has been examined and approved for operation by a qualiﬁed service technician.

• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat.

• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or sho rt out parts that could result in a risk of ﬁ re or electrical shock.

• Make sure that no objects enter into the vents and openings of the set.

• Do not expose this projector to rain or moisture.

• The projector is designed for indoor use only. Never operate the unit outdoors.

• Do not immerse or expose this projector in water or other liquids.

• Do not spill liquid of any kind on this projector.

• Should any liquid or solid object fall into the c abinet, unplug the set and have it checke resuming op erations.

• Do not d isassemble this projector, always take it to an authorized trained service person when service or repair work is required.

• Do not use an accessory attachment whic h is not recommended by the manufacturer.

• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.

d by qualiﬁed service personnel befo re

1. Safety

To prevent personal injury

• To prevent injury and physical damage, always read this m anual and all labels on the system before connecting to the w all outlet or adjusting the projector.

• To prevent injury, take note of the weight of the projector.

• To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.

• Warning: high intensity light beam. NEVER look into the lens! High luminanc e could result in damage to the eye.

• Warning: extremely high brightness laser: This projector uses extremely high brightness laser. Never attempt to look directly into the lens or at the laser.

• Always switch off the projector and disconnect from the mains power supply before attempting to remove any of the p rojector covers or access parts inside the projector.

• This product contains no user serviceable parts except the Color Wheel. Attempts to modify/replace mechanics or electronics inside the housing or compartm ents will violate any warranties and may be hazardous.

• Do not remove/replace any other parts than the Color Wheel. Other parts, s

• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user.

• Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.

• It is hazardous to operate without lens or lens cap. Lenses or shields shall be changed if they have bec ome visibly damaged, for example with cracks or deep scratches, to such an extent that the ir effectiveness is impaired.

ervice personnel only Warranty void if removed

601–426 F70 SERIES 18/04/2018

1. Safety

To prevent ﬁre hazard

• Barco projection products are designed and manufactured to meet the most s tringent safety regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing ﬂammable or combustible m aterials into close proximity of this projector could result in the spontaneous ignition of that material, resultinginaﬁre. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no ﬂammable or combustible materials are present. The exclusion zone in the exhaust area must be not less than 100 cm (40”). The exclusion zone on the intake area must not be less than 50 cm (20”).

• Do not place ﬂammable or combustible materials near the projector!

• For the F90 projector, the exclusion zone on the lens side within the light beam must be at least 1,5m.

• For the F70 projector the exclusion zone on the lens side within the light bea m must be at least 1,0m.

• Caution! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than 100 cm ( 40”) to the ex haust vent.

• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, these openings must not be blocked or covered.

• The openings should never be blocked by placing the projector too close to walls, or other similar surface. A llow for sufﬁcient distance to walls and ceilings to avoid overheating. Minimum s afety distance to the exhaust area of the unit must not be less than 100 cm (40”) and to the intake area, not less than 50 cm (20”).

• This projector should never be placed near or over a radiator or heat register.

• This projector should not be placed in a built-in installation o r enclosure unless proper ventilation is provided.

• Do not cover the projector or the lens with any material while the projector is in operation. Keep ﬂammable materials away from the projector at all times.

• Mount the p rojector in a well-ventilated area away from sources of ignition and out of direct sun light. A lways allow ample airﬂow through the projector.

• Never expose the projec tor to rain or moisture. In the event of ﬁre, use sand, CO2 or d ry powder ﬁre extinguishers.

• Never use water on an electrical ﬁre.

• Always have service performed on this projector by authorized B arco service perso placement parts. Nev er use non-Barco replacem ent parts as they may degrade the safety of this projector.

• Projection rooms must be well ventilated or cooled in order to avoid heat buildup.

• Let the projector cool down completely before storing. Remove cord from the projector when storing.

nnel. Always insist on genuine Barco re-

and combustible

To prevent projector damage

• To ensure correct airﬂow is maintained the projector should only be operated when all of its covers in place.

• Always remove lens cap before switching on th e projector. If the lens cap is not rem oved, it m ay melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens

• Only connect the projector to signal sources and voltages as described in the technica l speciﬁcation. Connecting to unspeciﬁed signal sources or voltages may lead to malfunction and permanent damage of the unit.

• To ensure correct airﬂow is maintained, it should only be operated when all of its covers are in place.

• The projector must always be installed in a manner which ensures free ﬂow of air into its air inlets and unim peded evacuation of the hot air from its cooling system.

• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the p roduct on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided. Ensure that nothing c an be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply immediately. Do not operate the projector again until it has been checked by Barco authorized service personnel.

• Do not block the projector cooling fans or free air m ovem ent around the projector. Minimum safety distance to the exhaust area of the unit must not be less than 100 cm (40”) and to the intake area, not less than 50 c m (20”).

• Do not use this equipment near water.

• Do not operate the projector outside its temperature and humidity speciﬁcations as this may result in overheating and malfunction.

• Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices™ in which case there is a loss of warranty.

• Save the original shipping carton and packing material. T hey will come in handy if y ou ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.

• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains m ay be removed with a cloth lightly dampen ed with mild detergent solution.

• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reﬂective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.

601–426 F70 SERIES 18/04/2018

1. Safety

On servicing

• Do not attempt to service this product y ourself, as opening or removing covers may expose you to dangerous voltage p otentials and risk of electric shock.

• Refer all servicing to Barco authorized repair centers.

• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty.

• Unplug this product from the wall outlet and refer servicing to Barco authorized service pers onnel or technicians under the following conditions:

- If liquid has been spilled into the equipment.

- If the product has been expo sed to rain or water.

- If the p roduct does not o perate normally when the operating instructions ar e followed. Adjust only those controls that are

covered by the operating instructions since improper adjustment of the other controls may r esult in damage and will often require extensive work by a qualiﬁed technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has been dam aged.

- If the product exhibits a distinct change in per formance, indicating a need for service.

- When the power cord or plug is damaged or frayed.

• Replacement parts: When replacement parts are re quired, be sure the service technician has used original Barco replacement parts. U nauthorized substitutions may result in degraded performance and reliability, ﬁre, electric shock or other hazards. Unauthorized substitutions may v oid warranty.

• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

1.3 Projector Hazard Distances

For F90 series: WARNING. This may be a RG3 laser Product, dependent on whi ch lens u

This projector may become Risk Group 3 (RG3) whe n an interchangeable lens with throw ratio greater than 3.15 is installed. For Northern America, installation requirements according to Risk group 3 (RG3) must be followed when interchangeable lens with throw ratio greater than 2.33 is installed

Refer to t he product ma nual for the lens list and throw ratio before operation.

Do not look directly in to the beam from the projector lens.

No direct eye exposure to the beam is permitted.

Operators shall c ontrol access to the beam within the hazard distance or install the product at a height that will prevent eye exposure within the hazard distance.

See table below for a deﬁnition of hazardous dis tances versus the throw ratio of the lens.

For F70 Series: WARNING. This may be a R G3 laser Product, dependent on which lens used.

This projector may becom e Risk Group 3 (RG 3) when an interchangeable lens with throw ratio greater than 4.7 is installed. For Northern America, installation requirements according to Risk group 3 (RG3) must be followed when interchangeable lens with throw ratio greater than 2.5 is installed

Refer to t he product ma nual for the lens list and throw ratio be

Do not look directly in to the beam from the projector lens.

No direct eye exposure to the beam is permitted.

Operators shall c ontrol access to the beam within the hazard distance or install the product at a height that will prevent eye exposure within the hazard distance.

See table below for a deﬁnition of hazardous dis tance

s versus the throw ratio of the lens.

fore operation.

sed.

1.4 High Brightness Precautions

Restriction Zone (RZ) based on the HD (Hazard Distance).

The HD depends on the amount of lumens produced by the projector and the type of lens installed. S ee next chapter"HD in function of the lens Throw Ratio (TR)", page 8 .

To protect untrained end users (as cinema visitors) the installation shall comply with the following installation requirements: Operators shall control access to the beam within the hazard distance or install the product at the height that will prevent spectators’ eyes from being in the hazard distance. Radiation le above any surface upon which persons other than operators, performers, or employees are permitted to stand or less than 1.0 meter (SH) lateral separation from any place where such persons are permitted to be. In non-cinema environments where unrestrained

601–426 F70 SERIES 18/04/2018

vels in excess of the limits will not be permitted at any point less than 2.0 meter (SH)

1. Safety

behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual’s sho ulders, within the HD.

These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section 6.6.5.

The end user m ust understand the risk and apply protective measures based upon the hazard distance as indicated on the label and in the user information. Installation method, barriers, detection system or other applicable control measure shall prevent hazardous eye access to the radiation within the hazard distance.

For example, projectors that have a HD greater than 1 m and emit light into an un controlled area where pe rsons may be present should be positioned in accordance with “the ﬁxed projector installation” parameters, resulting in a HD that does not extend into the audience area unless the beam is at least 2.0 meter above the ﬂoor level. In non-c inema environmen behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual’s shoulders, within the HD. For example, a sufﬁciently large separation height may be achieved by mo unting the image projector on the ceiling or through th

For applications installed in the USA market the abov e limits for cinema like environments do not apply. The relevant minimum separation height is 2.5m (8,2 ft) by the FDA CDRH. Non cinema like environments require 2.5 meter (8.2 ft) separation height and 1.0 me ter (3.3 ft) separation width for areas where restrained behavior is to be expected. All other areas require 3.0 (9.9 ft) separation height.

e use of physical bar riers.

ts where unrestrained

RA TH

Image 1-1 A Side View BTopView RA Restricted Area PR Projector TH Theater RZ Restriction Zone in the theater SH Separation Height SW Separation Width

Regarding the SH Distance: For Cinema applications, the distance must be >2m. For Concert applications, thedistancemustbe>3m.

(B) TOP VIEW(A) SIDE VIEW

Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related hazard dis tance (HD). This shall b e physically impossible by creating sufﬁcient separation height or by placing bar riers. The minimum separation height takes into account the surface upon which persons other than operator, performers or employees are permitted to stand.

On image 1-2 a typical setup is displayed. It must be veriﬁed if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This c an be done by using physical barrier, like a red rope as illustrated in image 1-2.

The restricted a rea sticker can be replaced by a sticker with only the sy mbol.

601–426 F70 SERIES 18/04/2018

Image 1-2

RESTRICTED

AREA

1. Safety

RESTRICTED

1.5 Hazard Distance for fully closed projection system

Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface unit becomes lower than the ap plicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to t

he light source is less than the HD .

Restriction Zone RZ Based on the HD

The projector is also suitable for rear proje in image 1-3 two areas should be considered: the restricted enclosed pr ojection a rea (RA) and the observation area (TH).

RESTRICTED

ction applications; projecting a beam onto a defuse coated projection screen. As displayed

RA TH

AREA

RESTRICTED

AREA

HDDIFFUSE

REFLECTION

Image 1-3 RA Restricted Access location (Enclosed projection area) PR Projector. TH Theater (observation area). RZ Restriction Zone PD Projection Distan SW Separation Widt

Restriction zo

h. Must be minimum 1 meter.

ne (RZ) based on the HD continued.

For this type of setup 3 different HD sh all be considered:

601–426 F70 SERIES 18/04/2018

1. Safety

• HD as discussed in "High Brightness precautions: Hazard Distance (HD)", page 6 , relevant for intrabeam exposure.

• HDreﬂection : the distance that has to be kept restrictive related to the reﬂected light from the rear projection screen.

• HDdiffuse : the relevant distance to be considered while observing the defuse surface of the rear projec tion sc reen.

As desc ribed in "High Brightness precautions: Hazard Distance ( HD)", page 6 , it is mandatory to create a restricted zone within the beam areas closer than any NOHD. In the enclosed projection area the combination of two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to the rear reﬂection from the screen (HDreﬂection); also taking into ac count a 1 m eter lateral separation.

The HDreﬂection distance equals 25 % of the difference between the determined HD distance and the projection distance to the rear projection screen. To determine the HD distance for the used lens a nd projector model see graphs in chapter "HD in f unction of the lens Throw Ratio (TR)", page 8 .

HDreﬂection = 25% (HD – PD)

The light emitted from the s creen within the observation shall never exceed the RG 2 exposure limit, determined at 10 cm. The HDdiffuse can be neglected if the m easured light at the screen surface is below 5000 c d/m² or 15000 LUX.

1.6 HD in function of the lens Throw Ratio (TR)

TR (Throw Ra ti o)

The ratio of the distance to the screen (throw) to the screen width.

HD versus Throw Ratio

Image 1-4 Hazard Distance in meters versus Throw ratio of the lens for the F90 projectors

12 601–426 F70 SERIES 18/04/2018

Hazard Distance Thermal Acidental Exposure

䲙

1,8

1,6

1,4

1,2

0,8

Hazard Distance [m]

0,6

0,4

0,2

0,5 0,9 1,3 1,7 2,0 2,3 2,7 3,1 3,5 3,9 4,3 4,7 5,1 5,5 5,9 6,3 6,7 7,1 7,5

Image 1-5 Hazard Distance in meters versus Throw ratio of the lens for the F70 projectors

Throw Rao

Graphs shows Hazard D istance in m eters versus Throw ratio o f the lens

1. Safety

1.7 Safety symbols

Description of safety symbols used in product documentation or on product.

Image Description

Refer to user manual for further information!

Caution! Do not stare into beam, RG2 product.

No telephone! Do not connect to telephone lines.

For F90 series: Warning Label

For North America, this projector may become RG3 when an interchangeable lens with throw ratio greater than

2.33 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use.

Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif interchangeable dont le rapport de projection est supérieur à 3,15. Veuillez vous reporter au manuel pour en savoir plus sur la liste des objectifs et la distance de sécurité avant toute utilisation. De telles combinaisons entre projecteur et objectif sont conçues pour des applications professionnelles uniquement et pas pour des applications grand public.

This projector may become RG3 when an interchangeable lens with throw ratio greater than 3.15 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use.

ᵜᣅᖡᵪᆹ㻵ᣅሴ∄བྷҾ3.15Ⲵᦒ䮌ཤˈᡀѪRG3Ǆ󰪞֌ࡽˈ䈧৲㘳᡻ ޼ѝ䮌ཤ␵অ઼ড 䐍⿫Ǆ ᵜᣅᖡᵪо䮌ཤ㓴ӵ׋уъ֯⭘ˈ䶎Პ䙊⎸䍩㘵֯⭘Ǆ

Caution! For North America: With interchangeable lens with throw ratio greater than 2.33, consider hazard distance and installation requirements for RG3 product. Refer User Manual.

Caution! With Interchangeable lens with throw ratio greater then 3.15, consider hazard distance and installation requirements for RG3 product. Refer User manual.

601–426 F70 SERIES 18/04/2018 13

1. Safety

䲙

㬌䁢䓚栆屯妲㈨埻姕⁁炻㕤⯭ỷ䑘⠫󰵶ἧ䓐㗪炻⎗傥㚫忈 ㆸ⮬柣㒦≽炻

⛐㬌䧖ね㱩ᶳ炻ἧ䓐侭㚫塓天㯪㍉⍾㝸ṃ怑䔞䘬⮵䫾ˤ

嬎⏲ἧ䓐侭

IEC EN 60825-1

CLASS 1 LASER PRODUCT

RG2 IEC EN 62471-5

㬌䁢䓚栆屯妲㈨埻姕⁁炻㕤⯭ỷ䑘⠫󰵶ἧ䓐㗪炻⎗傥㚫忈ㆸ⮬ 柣㒦≽炻

⛐㬌䧖ね㱩ᶳ炻ἧ䓐侭㚫塓天㯪㍉⍾㝸ṃ怑䔞䘬⮵䫾ˤ

嬎⏲ἧ䓐侭

Image Description

For F90 series: FDA Label

THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER

2016-V-0144 EFFECTIVE MARCH 6, 2017.

For F70 Series: Warning label

For North America, this projector may become RG3 when an interchangeable lens with throw ratio greater than 2.5 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use.

Ce projecteur peut devenir un projecteur RG3 en cas d'installation d'un objectif interchangeable dont le rapport de projection est supérieur à 4.7. Veuillez vous reporter au manuel pour en savoir plus sur la liste des objectifs et la distance de sécurité avant toute utilisation. De telles combinaisons entre projecteur et objectif sont conçues pour des applications professionnelles uniquement et pas pour des applications grand public.

For F70 Series: FDA Label

THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER 2016-V-0144 EFFECTIVE MARCH 6, 2017.

F70 EM C Label

This is a class A product. In a domestic environment this product

EMC:

may cause radio Interference in which case the user may be required to take adequate measures.

RG2 IEC EN 62471-5

CLASS 1 LASER PRODUCT

IEC EN 60825-1

This device complies with part 15 of the FCC Rules, Operation is subject to the following

FCC:

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CANADA:

This Class A digital apparatus complies with Canadian ICES-003, / Cet appareil numerique de Ia classe est conforme à Ia norme NMB-003 du Canada.

F90 EM C Label

This projector may become RG3 when an interchangeable lens with throw ratio greater than 4.7 is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use.

ᵜᣅᖡᵪᆹ㻵ᣅሴ∄བྷҾ4.7 Ⲵᦒ䮌ཤˈᡀѪRG3Ǆ󰪞֌ࡽˈ䈧৲㘳᡻޼ѝ䮌ཤ␵অ઼ড 䐍⿫Ǆ ᵜᣅᖡᵪо䮌ཤ㓴ӵ׋уъ֯⭘ˈ䶎Პ䙊⎸䍩㘵֯⭘Ǆ

Caution! For North America: With interchangeable lens with throw ratio greater than 2.5, consider hazard distance and installation requirements for RG3 product. Refer User Manual

Caution! With Interchangeable lens with throw ratio greater then 4.7, consider hazard distance and installation requirements for RG3 product. Refer User manual.

This is a class A product. In a domestic environment this product may

EMC:

cause radio Interference in which case the user may be required to take adequate measures.

FCC:

This device complies with part 15 of the FCC Rules, Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES-003, / Cet

CANADA:

appareil numerique de Ia classe est conforme à Ia norme NMB-003 du Canada.

Location of Safety Label

EMC Label Warning Label

Image 1-6 F90 Projector

RG2 IEC EN 62471-5

CLASS 1 LASER PRODUCT

IEC EN 60825-1

Image 1-7 F70 Projector

Warning and EMC labels

14 601–426 F70 SERIES 18/04/2018

1. Safety

Disposal Information

Waste Electrical and Electronic Equipment

This symbol on the product indicates that, under the E uropean Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipm ent by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

For more information about recycling of this product, please contact your local city ofﬁce or your municipal waste disposal service.

For details, pleas e visit the Barco website at: h

ttp://www.barco.com/en/AboutBarco/weee

WEEE Information

This product conforms to all requirements of the EU Directive on waste electrical and electronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to facilitate proper recycling of it’s individual parts.

Consult your dealer or relevant public authority regarding drop-off points for collection of WEEE. For details, please visit the Barco website at: http://www.barco.com/en/ AboutBarco/weee.

CAUTION: This product contains chemicals, including lead, known to the State of California to cause birth

defects or other reproductive harm. Recycle properly, do not dispose of in ordinary waste!

Turkey RoHS compliance

Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.

[Republic of Turkey: In conformity w ith the WEEE R egulation]

1.8 RoHS compliance

中国大陆 RoHS (Chinese Mainland RoHS)

根据中国大陆《电器电子产品有害物质限制使用管理办法》（也称为中国大陆RoHS ），以下部分列出了Barco产品中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS 指令包含在中国信息产业部MCV标准：“电子信息产品中有毒物质的限量要求”中。

According to the “Management Methods for the Restriction o f the Use of Hazardous Substances in Electrical and Electronic Products” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of t oxic substances in Electronic Information Products”.

601–426 F70 SERIES 18/04/2018

1. Safety

夃

零件項目（名稱）有毒有害物質或元素 Component Name Hazardous Substances or Elements

(Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE)

印製電路配件 Printed Circuit Assemblies

外接電（線）纜 External Cables

緉部線路 Internal wiring 鏡頭支架 Lensholder

激光發生器 Laser

底架 Chassis 外殼 Enclosure

螺帽，螺釘（栓），螺旋（釘），䐭圈緊固件 Nuts, bolts, screws, washers. Fasteners

電源供應商 Power Supply Unit 散熱片（器）

Heatsinks 風扇 Fan 塑膠外殼 Plastic Enclosure 外殼 Enclosure 電池（組） Batteries 文件茢明書 Paper Manuals 裝置配件 Installation kit 附電池遙控器 Remote control 本表格依據 SJ/T 11364 的規定編制。

This table is prepared in accordance with the provisions of SJ/T 11364.

O: 表示該有毒有害物質在該部件所有均質材料中的含量均在 GB/T 26572 標準規定的限量要求以下。

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572

X: 表示該有毒有害物質至少在該部件的某一均質材料中的含量超出 GB/T 26572 標準規定的限量要求。

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used forth is part is above the limit requirement in GB/T 26572.

鉛汞

X O X O O O

X O O O O O

O O O O O O

X O O O O O

O O O O O O

X O O O O O

O O O O O O

X O O O O O

六價壗多䘳聯䴙多䘳二䴙慂

Image 1-8

在中国大陆销售的相应电子信息产品（EIP ）都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限（EFUP）标签。Bar

co产品所采用的EF U P 标签（请参阅实例，徽标内部的编号使用于指定产品）基于中国大陆的《电子信息产品环

保使用期限通则》标准。

All Electronic Information P roducts (EIP) that are sold within Chines e Mainland must comply with the “Marking for the restriction of the use of hazardous substances in electrical and electronic product” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please r efer to the photo) is based on the “ General guidelines of environment-friendly use period of electronic information products” of Chinese Mainland.

601–426 F70 SERIES 18/04/2018

1.9 Taiwan RoHS compliance

1. Safety

零件项目 (名称)

Component Nam e

印制电路配件

Printed Circuit Assemblies

外接电( 线)缆

External Cables

內部线路

Internal wiring

镜头支架

Lensholder

激光发生器

Laser

底架

Chassis

外壳

Enclosure

螺帽,螺钉(栓 ),螺旋( 钉 ),垫圈, 紧固件

Nuts, bolts, screws, washers, Fasteners

电源供应器

Power Supply Unit

散热片 (器 )

Heatsinks

风扇

Fan

塑胶外壳

Plastic Enclosure

外壳

Enclosure

电池 ( 组)

Batteries

文件说明书

Paper M anuals

装置配件

Installation kit

有毒有害物质或元素

Hazardous Substances or Elements

铅

(Pb)

XOOOOO

OOO OOO

汞

(Hg)

OOOOO

镉

(Cd)

六价铬

(Cr6+)

OOO

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

601–426 F70 SERIES 18/04/2018 17

1. Safety

零件项目 (名称)

Component Nam e

附電池遙控器

Remote control

本表格依据SJ/T 11364的规定编制

This table is prepared in accordance with the provisions of SJ/T 11364.

O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 G B/T 26572 标准规定的限量要求以下.

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572.

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 标准规定的限量要求.

X: Indicates that this toxic or hazardous substance c ontained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.

有毒有害物质或元素

Hazardous Substances or Elements

铅

(Pb)

汞

(Hg)

OOOOO

镉

(Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

1.10 Contact information

Barco contact information

Registered ofﬁce address: President Kennedypark 35, 8500 Kortrijk, Belgium

Contact address: Beneluxpark 21, 8500 Kortrijk, B elgium

Contact address (for Taiwan) :

Barco ltd.., 33F., No. 16. Xinzhan Rd., Banqiao Dist.,, New Taipei City 220, Taiwan

Tel: +886-2-7715-0099, Fax: +886-2-7715-0097

E-mail: service.taiwan@barco.com

多溴二苯醚

(PBDE)

Importers contact information

To ﬁnd your local importer, contact Barco directly or one of Barco’s regional ofﬁces via the contact information given on Barco’s web site, w

ww.barco.com.

Contact information Norway factory

Barco F redrikstad as

Habornveien 53, N1630 Gamle Fredrikstad, Norway

Phone: +476930 4550

Support:Support.fre@barco.com

1.11 Product Info

Product info

Image 1-9

product name 產品名稱:

projector 投影機

model 型號:GP6/GP7

601–426 F70 SERIES 18/04/2018

1.12 Statement

EN55032/CISPR32 Class A MME (MultiMedia Equipment)

Warning : Th is equipment is compliant with Class A of CISPR 32. In a residential environment this equipment m ay cause radio interference.

Class A ITE (Information Technology Equipment)

Warning : This is a clas s A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

警告使用者: 此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。

1. Safety

601–426 F70 SERIES 18/04/2018

1. Safety

20 601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

2. GETTING TO KNOW THE PROJECTOR.

Overview

• Main Components

• Service and Maintenance

• LED Status Light

• Power on / Standby button backlight indications

• LCD panel

• Local keypad

• Remote Control

• Projector Address

• Connector panel

• Color Wheels

• Optional Accessories

2.1 Main Components

Naming Conventions

Left

Front

Image 2-1

Projector Items Overview

Top

Back

Right

Image 2-2

601–426 F70 SERIES 18/04/2018 21

2. Getting to know the projector.

LED Warning Indicator

Adjustable Feet

Lens

Lens Holder

IR Receiver. For receiving remote control signals

LCD Display

Keypad Panel. Used for local operation of the projector.

Connector Panel. Control and communication interfaces for the projector

Front USB and Triggerboard.

2.2 Service and Maintenance

General

The F70 series does not have any user serviceable parts.

All service tasks must only be carried out by the manufacturer, or a Barco authorized service personnel or Barco technicians.

2.3 LED Status Light

About

The F70 Status Led is located on the rear top of the Projector

During normal operation, the LED is not illuminated. In the event of a critical error or high temperature, the LED will illuminate red.

By critical error, the projector cannot be r estarted until the projector is disconnected from the power s upply and then reconnected again. If the reason for the error persist, the projector will again go to critical error status.

By high temperature, the p rojector can be restarted when it has cooled down, and the temper ature is back within the no rmal operating limitations

2.4 P ower on / Standby button backlight indications

Indicator

In addition to the LED indicator, the p

The table below shows the details r egarding this indications.

Operating Status Indication Color / Behavior

On (active)

Wait on

Standby (off)

Wait

Overheating Red ﬂashing

Conﬁgure/upgrade White fast ﬂashing

Standby ECO

rojector also displays status indications in the backlight of the Power / Standby button.

Blue

Blue ﬂas hing

White

White short ﬂashing

White heartbeat

22 601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

2.5 LCD panel

About

The LCD panel (reference 1, image 2-3) is located on the right side of the projector, and has two main functions:

1. Showing the menus and adjustment information. and also a mirror of the OSD, (On Screen Display) described in User Interface

when this is enabled.

2. Information regarding the status of the projector showing this data:

- Projector status

- Network address

- Active source

- Current ﬁrmware version

- Operation Data

- Active functions (Enabled Functions).

Toggle between the two indications by using the Menu button on the keypad, or on the remote control

The LCD Display will fade out 15 seconds after the last key operation.

2.6 Local keypad

About

The Keypad gives direct access to s everal functions, in addition to access to the menu system. The keypad and remote control functions are equal.

The keypad has a back light that can be switched o n and off manually. The light turns off automatically after a preset time.

The Standby key is equipped with white, blue and red backlight depending on the status of the projector. See table in "Power on / Standby button backlight indications", page 22 for info regarding this.

Image 2-3

Item

Name Description

No.

1 LCD Display Shows Projector status and navigation menu.

2 Navigation keys Navigation arrows (up, down, left, right), conﬁ rm selection ( )

3 OSD Display Enables the Home Menu on the LCD screen and the OSD.

4 Standby Power on / standby

Back Undo action / back to previous screen.

6 OSD ON/OF F Deactivate the On Screen Display (OSD). Only critical warnings will be displayed.

Input Shortcut to input source menu on LCD. Use navigation keys to select and enable input.

9 8

3 4

601–426 F70 SERIES 18/04/2018 23

2. Getting to know the projector.

Item

Name Description

No.

Shutter Enable and disable the lens shutter function. This is not a mec hanical shutter, but it toggles

9 Test Patterns

10 Lens

the laser source on and off. Backlight is red when the shutter are enabled.

Shortcut to test pattern menu on LCD. Use navigation keys to select the desired pattern.

Shortcut to lens function. A test pattern displays on the OSD. LCD screen displays the navigation keys to manage and conﬁrm actions.

2.7 Remote Control

2.7.1 Remote control, Battery installation

Where to ﬁnd the batteries for the remote control ?

The b atteries are not placed in the remote control unit to avoid control operation in its package, resulting in a s horter battery life time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control, install the batteries ﬁrst.

How t o install

1. P ush the battery cover tab with the ﬁngernail a little backwards (1) and pull, at the s ame time, the cover upwards (2).

Image 2-4

2. Insert the two AA size batteries, making sure the polarities match the + and - m arks inside the battery compartment.

Tip: Use alkaline batteries for optimum range and life time.

Image 2-5

3. Insert (1) both lower tabs of the battery cover in the gaps at the bottom of the remote control, and press (2) the cover until it clicks

in place.

Image 2-6

24 601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

When replacing batteries, t he broadcast address o f the RCU will be reset to its default value ’0’.

CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the

battery is replaced with an incorrect type.

CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly

installed.

2.7.2 Remote control, protocol setup

About the used protocol

The protocol is the code send out by th e remote control when a button is pressed. Depending on this code, the projector can decode the signals. The remote control can be used with two different protocols, RC5 and NEC. Depending on the projector to control the remote control can be switched between these protocols.

Which protocol to use

•TheNEC protocol have to be used for Barco projectors based on the Pulse platform: Loki, Balder, F70, F80, F90, HDX 4K,

UDX, ...

•TheRC5 protocol have to be use all other Barco projectors: HDX W, HDF W, HD

Q2K,...

How to set

1. R emov e the cover. For more info on how to remo ve, see "Remote c ontrol, B attery installation", page 24.

2. P lace the switch in the N EC position.

Image 2-7

Remark with RC5 protocol

Not all buttons of the Pulse RCU are o ne-to-one compatible with the legacy Bar co RCU. Button pairs SHUTTER open/close and POWER on/off emit the sam e code (per pair) when in RC5 mod e, because the legacy RC U’s only had 1 button for Shutter and 1 button for Standby.

601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

2.7.3 Functionality overview

Remote Control Unit buttons

Button pressed indicator.

Shutter Open.

Shutter Close.

Touch Panel O n/Off. (Not in

use).

OSD On/Off.

Lens Zoom.

Lens Shift.

Menu Activation.

Menu Selection, OK button.

Menu Navigation.

Input Selection.

Address button.

Numeric buttons.

Backspace (while entering

values)

XLR connector.

Decimal mark (while entering

values)

Macro button. (Not in use)

Menu Bac k.

Default button. (Not in use).

Lens Focus.

Real Color menu..

Test Patterns.

Power On.

Power Off.

Stereo Jack.

RCU On/Off.

2625

The projector re mote control is a full feature wireless rem ote control, powered by two (2) standard AA batteries. The battery compartment is on the back side of the remote control.

The remote control is backlit for use in dark environments. It also has an Jack connector for wired connec tion to the projector. When the wire is connected, the IR beam is s witched off.

2.7.4 Remote control, on/off button

Purpose of the remote control on/off button

The Pulse remote control unit has at the front side an on/off switch (reference 1 image 2-8). Switching off the remote control prevents that unwanted commands are send due to an accidental key press. Furthermore, switching the RCU off will extend the battery life time of the remote control.

To activate the remote control press the on /off button.

To deactivate the remote control press the on/off button again.

Default when (re)placing batteries, is “ON”.

Image 2-8

26 601–426 F70 SERIES 18/04/2018

2.7.5 Enable / Disable Remote Control

About

This function are for disabling the IR sensors for the rem ote control. Either front or rear, or both.

Image 2-9

• Select the menu path Home/System Settings/Communication/IR control

• Select which sensors to be disabled.

• Enter the Apply button to conﬁrm the action

When all sensors are turned off, the projector w ill not receive any signals from the remote control. To enable the sensors again, use the keypad on t he projector.

2. Getting to know the projector.

2.7.6 Wired RC connection

About

The remote control can also be directly wired to the projector from the stereo jack connector on the remote, (See "Functionality overview", page 26 ), to the RC connector on the back panel of the projector.(See section “Connector P anel”)

In this mode, the projector will not be affected by signals from other non-wired remote controls.

When using wired remote c ontrol, the broadcast address must be set to “Generic ID (0)”. See the menu in "Enable / Disable Remote Control", page 27.

It is not possible to program the remote control in wired mode. (Directly connected, no sense in programming).

2.8 Projector Address

Projector address

Address installed in the projector to be individually controlled.

Broadcast ad dress

Projector will always execute the command co

2.8.1 Controlling the projector

Why a projector address?

As more than one projector can be installed in a room, each pr ojector should be separately addressable with an RCU or com puter. Therefore each projector has its own address.

ming from a RCU programmed with that broadcast address.

Set up an individual Projector A ddress

The set up of a projector address can be done via the software.

601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

Projector controlling

When the address is set, the projector can be controlled now:

• with the RCU: only for addresses between 1 and 31.

Broadcast Address

Every projector h as a broadcast (common) address ’0’ or ’1’. The default address is ’0’.

The choice between ’0’ and ’1’ c an be selected in the GUI: “Sy stem Settings” → “Communication” →“IR Control “.

Placing new batteries in the remote control or plugging the remote to a projector via a cable will automatically reset the address back to its default value ’0’.

2.9 Connector panel

General

The source input panel is located at the back of the projector. For source speciﬁcations, see table below.

Image 2-10

Name Pcs Description Purpose

DMX IN 1 DMX 512 input

DMX OUT

RS-232

Sync

Trigger 3 (one in

USB

LAN 1

DP 2

DL-DVI-D 2

HDMI 1

HDBaseT 1

SDI

1 DMX 512 output

1 9–pin DB9 connector

front, two on rear panel)

BNC Sync Port IN/OUT; B idirectional mini-DIN (1x 3D sync Out, and 2x Sync In/Out)

12VDC - 0,5A (6W) For Controlling Peripherals, like motorized screens, curtains

Jack connector for wired remote For Projector Control

USB 2.0 type A, 4 pin( 2x Rear and 1x Front)

Standard RJ45 connector For Projector Control

Standard display port

Dual DVI-I 1.0 (DVI_D Functionallity).

Standard HDMI 2.0

Standard RJ45 8P8C Connector For Projector Control

SDI1 is Input, SDI 2 is pass through. (out)

For Projector Control

For Projector Control. A llows for wired remote control and monitoring of m any projector functions used in installation environments

For Projector ControlThis is mainly used in multiple projector installations with requirement of synchronization between the units

etc. Give 12V output when projector are switched on

For Software upgrade

For Projector Input

For Projector Input. These connectors can also be used to form one uniform image by feeding half of the image into each connector. HDCP compliant for sources up 165 Mhz

For Projector Input

28 601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

Connectors

2.10 Color Wheels

About

The F70 Projector is delivered with a standard Color w heel, that is suitable for most applications.

Other colorwheels are available upon request.

Consult Barco sales ofﬁce or a service partner in order to ﬁnd the most suitable colorwheel for the s peciﬁc application.

2.11 Optional Accessories

Rigging Frame

Item Numb er Item Description

R9802224

The F70 Rigging frame is a rugged, easy to install frame, designed to streamline the process of installing one or more projectors.

When installed i the frame, the projector:

• can be rotated around the x, y and z axis, in order to obtain a seamless adjustmen t in applications using multiple projectors.

• Can be installed from a truss or a pe destal.

• Can be easily stacked one on top of another, for instance a dual or multichannel installations.

F70/F90 Multifunctional Fram e.

Flight Cas e

F70 use the same Flight case as the F90 series projectors.

Item Numb er Item Description

R9801195 F90 ﬂight case.

Image 2-11

The F70 Flight Case is a custom designed c ontainer, that is suitable for shipping the projector, including ﬂight frame, signal and power cords and up to two lenses.

The case is fully-lined to protect the projector and lenses during trans it and storage.

601–426 F70 SERIES 18/04/2018

2. Getting to know the projector.

30 601–426 F70 SERIES 18/04/2018

3. LENSES

About

Overview

• Approved Lenses

• Lens ran ge

• Replace a lens

• Lens s hift

• Adjust zoom and focus

• Adjust Iris

3.1 Approved Lenses

Approved Lenses

Partnumber Description For North Amrica

R9801214

R9801218

R9801228

R9801209

R9801225

R9801249

FLD 1.6 - 2.32 : 1 (EN11)

FLD0.74:1(EN12)

FLD 1.24 - 1.6 : 1 (EN13)

FLD 2.37 - 3.79 : 1 (EN14) approved – professional use

FLD1:16:1(EN15)

FLD 3.8 - 6.5 : 1 (EN16) approved – professional use

approved approved

only approved approved

only

3. Lenses

Outside North am erica

approved – professional use only

R9801216

R9801226

R9801230

R9801211

R9801220 FLD+ Long Focus 0.8 - 1.21 :

R9801221

R9801295

PN_EN58

Refer to the manual chapter 1.7 for the throw ratio versus hazard distance before o peration.

FLD+ 1.7 - 2.5 : 1 (EN41)

FLD+ 0.8 : 1 (EN42)

FLD+ 1.2 - 1.7 : 1 (EN43)

FLD+ 2.5 - 4.6 : 1 (EN44) approved – professional use

1 (EN45) FLD+ Short Focus 0.8 - 1.21 : 1 (EN46) FLD+ 0.65 : 1 (EN47)

FLD+ 0.28 : 1 (EN58)

approved approved

only approved approved

approved approved

approved – professional use only

3.2 Lens range

CAUTION: Alw ays remove the lens from the lens holder before moving or transporting the projector. Failure

to do this may cause damage to the lens holder and prism.

Available lenses — WUXGA

The FLD lens range is custom-engineered for WUXGA and 1080 projectors.

The electrical connection to the lens motors is via a spring probe contact (pogo) pin array on the bayonet mount.

The p rojector will automatically detect and identify the lens when it is installed. Automatic detection is not available for 3rd party lenses.

601–426 F70 SERIES 18/04/2018

3. Lenses

EN11 EN12 EN13 EN14 EN15 EN16 EN33

Image 3-1

Name Description Part number Weight

FLD Lens 1.6 - 2.32 : 1 (EN11)

1.6-2.32 : 1 (WUXGA)

R9801214 2.2 kg

FLD Lens 0.74 : 1 (EN12) 0.74:1 (WUXG A)

FLD Lens 1.24 - 1.6 : 1 (EN13)

FLD Lens 2.37 - 3.79 : 1 (EN14)

FLD Lens 1.16:1 (EN15) 1.16 : 1 (WUXGA) R9801225 2.4 kg

FLD Lens 3.80 - 6.50 : 1 (EN16)

Name

FLD Lens 1.6 - 2.32 : 1 (EN11)

FLD Lens 0.74 : 1 (EN12) 2.1 Yes 2.1-6.5

FLD Lens 1.24 - 1.6 : 1 (EN13)

FLD Lens 2.37 - 3.79 : 1 (EN14)

FLD Lens 1.16:1 (EN15)

FLD Lens 3.80 - 6.50 : 1 (EN16)

1.24 - 1.6 : 1 (WUXGA)

2.37 - 3.79 : 1 (WUXGA)

3.8 - 6.5 : 1 (W UX GA) R9801249 2.5 kg

Working F# Iris / Iris F#

2.1-2.52 Yes 2.1-6.5 1.45 33.2-48.1 2.0-15

2.1-2.22 Yes 2.1-6.5 1.3 25.59-33.24 1.0-15

2.1-2.72 Yes 2.1-6.5 1.6 49.1-78.6 3.0-30

2.1 Yes 2.1-6.5

2.1-2.66 Yes 2.1-6.5 1.74 78.3-136.2 4.0-40

Zoom Ratio Focal Length

R9801218 1.9 kg

R9801228 2.6 kg

R9801209 2.5 kg

Focus Range (m)

(mm)

16.35 0.5-5

23.98 1.5-15

Available lenses — 4K, WUXGA, WQXGA

The FLD+ (EN4X) lens range is custom-engineered for WQXGA projectors.

The electrical connection to the lens motors is via a spring probe contact (pogo) pin array on the bayonet mount. The projector will automatically detect and identify the lens when it is installed. Auto matic detection is not available for 3rd party lenses.

EN41

Image 3-2

32 601–426 F70 SERIES 18/04/2018

EN42 EN43 EN44 EN45 EN46

Name Description Part number Weight

FLD+ Lens 1.7 - 2.5 : 1 (EN41) 1.58 - 2.33 : 1 (WUXGA) / 1.7 - 2.5 : 1

FLD+ NV Lens 1.7 - 2.5 : 1 (NV41)

FLD+ Lens 0.8 : 1 (EN42) 0.75 : 1 (WUXGA) / 0.8 : 1 (W QXG A)

FLD+ Lens 1.2 - 1.7 : 1 (EN43) 1.12 - 1.58 : 1 (WUXGA) / 1.2 - 1.7 : 1

FLD+ NV Lens 1.2 - 1.7 : 1 (NV43)

FLD+ Lens 2.5 - 4.6 : 1 (EN44) 2.33 - 4.3 : 1 (WUXGA) / 2.5 - 4.6 : 1

FLD+ Lens 0.75 - 1 .13 : 1 (EN45) 0.75 - 1.13 : 1 (WUXGA) / 0.8 - 1.21 :

FLD+ Lens 0.75 - 1 .13 : 1 (EN46) 0.75 - 1.13 : 1 (WUXGA) / 0.8 - 1.21 :

FLD+ NV Lens 0.8 - 1.21 : 1 (NV46)

FLD+ Lens 0.65 : 1 (EN47) 0.61 : 1 (WUXGA) / 0.65 : 1 (WQXGA) R980129 5 5.4 kg

(WQXGA)

IR Optimized, 1.58 - 2.33 : 1 (WUXGA) /

1.7-2.5: 1(WQXGA)

(WQXGA)

IR Optimized, 1.12 - 1.58 : 1 (WUXGA) /

1.2-1.7: 1(WQXGA)

(WQXGA)

1(WQXGA)

IR Optimized, 0.75 - 1.13 : 1 (WUXGA) / 0.8 - 1.21 : 1 (WQXGA)

R9801216 2.54 kg

R9801226 2.7 kg

R9801230 2.84 kg

R9801286 2.84 kg

R9801211 3.08 kg

R9801220 3.04 kg

R9801221 3.14 kg

R9801287 3.14 kg

3. Lenses

Name Working F# Iris / Iris F# Zoom Ratio Focal Length

FLD+ Lens 1.7 -

2.5 : 1 (EN41)

FLD+ NV Lens 1.7

- 2.5 : 1 (NV41)

FLD+ Lens 0.8 : 1 (EN42)

FLD+ Lens 1.2 -

1.7 : 1 (EN43)

FLD+ NV Lens 1.2

- 1.7 : 1 (NV43)

FLD+ Lens 2.5 -

4.6 : 1 (EN44)

FLD+ Lens 0.75 -

1.13 : 1 (EN45)

FLD+ Lens 0.75 -

1.13 : 1 (EN46)

FLD+ NV Lens 0.8

-1.21: 1(NV46)

FLD+ Lens 0.65 : 1 (EN47)

2.1-2.5 Yes 2.1-6.5 1.47 33.70-49.54 1.5 - 15

2.1 Yes 2.1-6.5

2.4-2.7 Yes 2.4-6.5 1.42 23.95-34.02 1.5 - 15

2.1-2.93 Yes 2.1-6.5 1.85 49.52-91.60 2.5-25

2.4-3.29 Yes 2.4-6.5 1.51 15.85-23.93 5.0 - 30

2.4-3.29 Yes 2.4-6.5 1.51 15.98-23.99 0.7 - 7

2.1 Yes 2.1-6.0

3.3 Replace a lens

(mm)

Focus Range (m)

16.12 0.7 - 7

12.6 0.5 - 4.0

Lens lever

The F70 lens mount and lens lever is designed to prevent damage to the lens board while providing an easy and stable lens change procedure.

The lens lever, located at the bottom of the lens mount, slides between two positions, far left (default position — unlocked) and far right (locked).

Always activate the projector shutter before attempting to remove or install a lens.

To do this, press the shutter button on the keypad, or shutter Close on the remote, to activate the shutter. The keypad button will illuminate red when the shutter is activated.

Press the shutter bu tton again, or shutter Open on the remote, to deactivate the shutter and resume norm al operation. The keypad button will illuminate white when the shutter is deactivated.

601–426 F70 SERIES 18/04/2018 33

3. Lenses

Image 3-3

Install a lens

1. Verify that the projector shutter is activated (shutter is ac tivated when the shutter icon on the projector keypad is red).

2. Verify that the lens release lever is in its default position at the far left of the slide, as illustrated.

3. Remove the protective cap at the lens bayonet end

4. A lign the lens so that the red marking on the bayonet is facing upwards.

5. P osition the lens bay onet into the projector lens m ount and support in place with one hand.

6. S lide the lens lever to the far right.

7. Verify that the lens is ﬁrmly in place before removing your hand from the lens.

Image 3-4

Removealens

1. S upport the lens with on e hand.

2. Use the other hand to slide the lens release lever to the far left position.

3. P ull the lens straight out of the projector lens moun t.

4. Replace with another lens, or install the projector lens cap.

Image 3-5

34 601–426 F70 SERIES 18/04/2018

3.4 Lens shift

General

Use the Remo te control or the keypad on the P rojector to adjust the lens s hift mechanism.

The lenses can be shifted vertically and horizontally to facilitate precise image positioning in single and multiple projecto r systems. The projector allows for horizontal and vertical shift in both directions. Always place the projector perpendicular to the screen, and use the lens shift to align the picture.

If not possible to align the projector perpendicular to the screen, due to environmemt of other, see chapt adjustment", page 77

er "Warp – 4 Corners

3.5 Adjust zoom and focus

General

Zoom controls the size of the projected image.

Focus controls the sharpness of the projected image.

Lens zoom and focus a djustments are motorized. You can use the remote control, loca l keypad, OSD and/or RS-232 commands to adjust the lens zoom and focus positions.

Not all lenses have zoom or iris control. The matrix b elow shows what controls are available per lens.

3. Lenses

EN11 EN12 EN13 E N 14 EN15 EN16 EN33 EN41 EN42 EN43 EN44 EN45 EN46 EN47

Iris

Zoom

Focus

For best results, lens adjustments should be done in the following order: zoom, focus and then iris (w here applicable).

✔✔✔✔✔✔

✔

✔✔✔✔✔✔✔✔✔✔✔✔✔✔

✖

✔✔

✖

✔

✖

✔✔✔✔✔✔✔

✖

✔

✖

✔✔✔✔

3.6 Adjust Iris

General

Iris controls the contrast and focus depth of the image. De creasing the iris will increase contrast and image depth, at the same time

as it decreases brightness.

Iris control is, as for the zoom and focus control, motorized, and is operated by the remote control or local keypad.

Iris is only available for units w ith COLOR type colorwheel.

To enter Iris control, enter the menu Home/Installation/Lens /Iris

✖

601–426 F70 SERIES 18/04/2018

3. Lenses

Image 3-6

Use the arrow keys to adjust Iris until preferred rendering is obtained.

601–426 F70 SERIES 18/04/2018

4. Physical Installation

4. PHYSICAL INSTALLATION

About

This chapter describes the physical c onditions and procedures required w hen installing the F70 projector. It also describes the outlines and some of the considerations that should be taken in to account when designing and setting up the installation.

Each projector installation is unique, and as such the information in this chapter is only provided as a guideline. Likewise, any images or graphical r epresentations shown here are for illustrative purposes only.

If you re quire further information and assistance during the installation process, contact a qualiﬁed projection technician or your local support ofﬁce for advice.

Overview

• Installation Process

• Installation conditions

• Initial inspection

• Positioning the projector

• Mounting the projector, general considerations

• Projector safe attachment points

• Throw distance

• Scheimpﬂug (Boresight) adjustment

• Scheimpﬂug adjustment procedure

4.1 Installation Process

Recommended Installation sequence

Item Procedure Read more in chapter

2 Decide where the projector will be mounted

4 Mount the projector See "M ounting the projector, general considerations",

6 Connect the source See "Projector source and control connections", page

Conﬁrm that the installation area meets all technical and environmental requirements

Unpack the projector and conﬁrm that all equipment is present and in good working order

Install the projector lens See "Replace a lens", page 33

Power up the projector

Set up the image See "Image menu", page 59

4.2 Installation conditions

Environmental Conditions

Barco projectors are m anu factured according to speciﬁc design standards, which also include environmental conditions. Failing to follow the terms a warranty

See "Installation conditions", page 37

See "Positioning the projector", page 39

See "Initial inspection", page 38

page 39

47 See "Power up the projector", page 50

nd conditions outlined in this chapter can result in loss of product

The table below summarize the physical en

Environment Ambient operating

temperature

0 -500m +10 to +45 °C 10 –80% RH –20 to +60 °C, 10 – 90 % RH

500 -1500m +10 to +40 °C 10 –80% RH –20 to +60 °C, 10 – 9 0 % RH

601–426 F70 SERIES 18/04/2018 37

vironments in which th e projector may be safely operated or stored.

Relative Humidity

Storage condition

4. Physical Installation

Environment Ambient operating

1500 - 3000m

Maximum Air Flow

temperature

+10 to +35°C 10 –80% RH –20 to +60 °C, 10 – 90 % RH

/hour 10 –80% RH

900m

Relative Humidity

Storage condition

Not Applicable

Mains power requirement

Projector Power Requirement

F70 100 –240V. 50 –60 Hz.

To protect operating personnel, the National Electrical Manufacturers Association (NEM A) recommends that the instrument panel and cabinet be grounded.

In no event shall this projector be operated without an adequate cabinet ground connection.

The AC supply must be installed by a qualiﬁed electrician in conformance to local codes. Hardware, wire sizes and conduit types must comply with local codes.

Ventilation

The free space necessary between the air intake and exhaust are shown below.

1000 mm

500 mm

Image 4-1

4.3 Initial inspection

General

Each projector is inspected and rigorously tested at our production facility to ensure that it is free from any mechan ical or electrical defects.

Upon receipt of the projector, we recommend that customers inspect the projector for any signs of damage that may have occurred in transit. If damage is found, ﬁle a claim with the shipping carrier im mediately. Notify the Barco Sales and Se rvice ofﬁce, or your preferred Barco agent, of the damage as soon as possible.

Box Contents

Your projector box should contain the following:

601–426 F70 SERIES 18/04/2018

4. Physical Installation

• Projector unit

• Power cord (suitable for region)

• Quick start guide

• Safety manual

• Remote Control

The projector lens is delivered in a separate box.

4.4 Positioning the projector

CAUTION: The position and physical securing of the projector must be sufﬁcient to prevent it from accidental

or involuntary movement. Proper securing of the projector is the responsibility of the installer and user. The Projector are heavy, and can cause severe damage and injuries if falling.

General guidelines

Proper positioning of the projector lessens the overall picture setup time, and ens ures a better image with fewer artifacts.

Focus and sharpness of the image can be adversely affected if the lens axis is not fully perpendicular to the projection surface.

Using extended cable lengths may result in reduced image quality as well as loss of control information such as EDID (Extended Display Inform ation Data).

The following guidelines can help you determine the best physical location for the projector.

• Only install the projector on a s turdy ﬂat s urface, or in an approved rigging frame.

• Do not install the projector in a thoroughfare or another area where it is at risk of being pushed or jostled.

• Allow sufﬁcient free sp ace around the pr ojector for ventilation and exhaust, as described in section 4.2

• Use the throw ratio of the ins talled lens as a guideline for the proje

• Wherever possible, the projector lens surface should be positioned so that it is perfectly perpendicular to the cen ter of the

screen. Use the projector offset (lens shift), rather than physical angling, to correct any off-center positioning.

• Minimize the source cable length as much as possible.

In general HDBaseT and 3G-SDI are long-haul interfaces and suitable for bespoke installations using relatively long cables. DP, HDMI and DVI are short-haul interfaces using pre-assembled cables with limited cable lengths.

• Limit the use of power cable extensions wherever possible. Where physical limitations necessitate their use, make sure that

the extension cord has adequate surge protection and meets all electrical requirements of the connection.

• Keep the projector away from equipment that emits electromagnetic ener

ctor’s physical distance from the screen.

gy for example, motors, transformers and elevators.

4.5 Mounting the projector, general considerations

Mounting safety

When mounting a projector in a rig, always use an interface plate (between the projector and the mount) that has provision for a safety wire or another safety mechanism, to ensure that the projector does not fall down should the interface plate come loose from the m ount.

Always screw the interface plate securely to the projector body while the projector is on the ground (i.e. cannot fall down). Then attach proper safety wire between the interface plate a

Using 3rd party mounting equipment

The projector has features for mounting into various system environments using 3rd party m ounts.

601–426 F70 SERIES 18/04/2018

nd the rig before mounting the projector in the rig

4. Physical Installation

Four m ounting inserts are located on the bottom of projector. The ceiling mount inserts have a pull-strength of more than 4x the weight of the projector.

The feet can b e removed and threads can be used for additional mounting points. See table below for dimen sions.

Parameter Value

Thread size M12

Length 18mm max 18mm max

Where possible, the projector lens must be positioned exactly p erpen dicular to the center of the sc reen. Use the projector offset (lens shift), rather than physical angling, to correct an y off-center positioning.

CAUTION: The position and physical securing of the projector must be sufﬁcient to prevent it from accidental

or involuntary movement. Proper securing of the projector is the responsibility of the installer an d user.

CAUTION: Always use a Rigging Frame when the projector shall be mounted in other ways than on the feet,

on a ﬂat surface.

The threaded hole in the lower back end of the projector is NOT suitable for lifting or other heavy op erations. Only for adjustment purposes.

Installation and use of the Rigging Frame are described in document R5906768 Multifunctional Frame — In stallation Manual.

Mounting on a ﬂat surface

1. P osition the projector at the desired location.

2. P ower up the projector.

3. G o to Main Menu / Test Patterns and select an internal hatch pattern to display on the screen.

4. A djust the projector legs until the projected hatch pattern is a level and perfect rectangle.

Adjustable feet

Twisting the adjustable feet in either direction, left or right, allows you to ﬁne-adjust the projector position for precise vertical mechanical alignment.

Raise

Lower

Image 4-2

Mounting to a ceiling

1. Install the projector in to an approved rigging frame.

2. Install the rigging frame to the desired location.

3. P ower up the projector.

601–426 F70 SERIES 18/04/2018

4. Physical Installation

4. G o to Main Menu / Installation / Orientation and select the correct o rientation for your setup.

5. G o to Main Menu / Test Patterns and select an internal hatch pattern to display on the screen.

6. A djust the position (height and angle) of the rigging frame until the projected hatch pattern is a level and perfect rectangle.

If applied in a motion rig, care must be taken to stay within the environm ental speciﬁcations for vibration and shock. It may also be necessary to use additional, custom means to stabilize the projection lens to m ake sure that the projected image remains in position an d properly focused.

4.6 Projector safe attachment points

About

Due to use of a Rigging Frame or other equipmen t, the projector has some deﬁ nes anchor points that shall be used. See the illustration below.

Note that there is only this 4 selected attachment points that is approved as anchor points for the unit.

Anchorpoints. For attaching to rigging frame or similar.

Image 4-3

Item Thread Dimension Max Hole Depth Application

1 M6 15mm Anchorpoint / Ceiling / Rig

601–426 F70 SERIES 18/04/2018 41

Mount

4. Physical Installation

4.7 Throw distance

Calculate the installation throw distance

Throw is the distance (D) measured from your projector lens to the screen. To calculate the throw distance for an installation, you will need two pieces of data: the selected lens throw ratio (L) and the horizontal width (W) of the screen. For ex ample, if the screen width (W) is 2.4 m eters and the projector lens has a throw ratio ( L) of 0.99:1, then the throw distance (D) will be 2.38 meters.

Calculation: 2.4 x 0.99 = 2.38

The following graphs illustrate the image size (W) and projection distance (D) for each of the projector l

Tolerances are typically +/- 5% due to optical (lens) variation.

Throw distance, FLD WUXGA

7.50

enses.

Image width

12.00

Screen diagonal

14.00

7.00

6.50

6.00

5.50

5.00

4.50

4.00

3.50

3.00

2.50

2.00

1.50

1.00

0.50

0.00

FLD Lens 0.74:1 (EN12) (0.5 - 5m)

FLD Lens 1.16:1 (EN15) (1.5 - 15m)

FLD Lens 1.24 - 1.6 : 1 (EN13) (1.0 - 15m)

FLD Lens 1.6 - 2.32 : 1 (EN11) (2.0 - 15m)

FLD Lens 2.37 - 3.79 : 1 (EN14) (3.0 - 30m)

FLD Lens 3.80 - 6.50 : 1 (EN16) (4.0 - 40 m)

11.00

10.00

9.00

8.00

7.00

6.00

5.00

4.00

3.00

2.00

1.00

0.00

13.00

12.00

11.00

10.00

9.00

8.00

6.00

5.00

4.00

3.00

2.00

1.00

0.00

Image 4-4

Projection distance

42 601–426 F70 SERIES 18/04/2018

Throw distance, FLD+ WQXGA / 4K UHD

Image height

7.50

4. Physical Installation

Image width

12.00

Screen diagonal

14.00

7.00

6.50

6.00

5.50

5.00

4.50

4.00

3.50

3.00

2.50

2.00

FLD+ Lens 0.65 : 1 (EN47) (0.5 - 4m)

1.50

1.00

0.50

0.00

FLD+ Lens 0.8 : 1 (EN42) (0.7 - 7m)

FLD+ Lens 0.8 - 1.21 : 1 (EN46) (0.7 - 7m)

FLD+ Lens 0.8 - 1.21 : 1 (EN45) (5 - 30m)

FLD+ Lens 1.2 - 1.7 : 1 (EN43) (1.5 - 15m)

FLD+ Lens 1.7 - 2.5 : 1 (EN41) (1.5 - 15m)

FLD+ Lens 2.5 - 4.6 : 1 (EN44) (2.5 - 25 m)

11.00

10.00

9.00

8.00

7.00

6.00

5.00

4.00

3.00

2.00

1.00

0.00

13.00

12.00

11.00

10.00

9.00

8.00

6.00

5.00

4.00

3.00

2.00

1.00

0.00

Image 4-5

Projection distance

601–426 F70 SERIES 18/04/2018 43

4. Physical Installation

Throw distance, FLD+ WUXGA

7.50

Image width

12.00

Screen diagonal

14.00

7.00

6.50

6.00

5.50

5.00

4.50

4.00

3.50

3.00

2.50

2.00

1.50

1.00

0.50

0.00

FLD+ Lens 0.65 : 1 (WUXGA) (EN47) (0.5 - 4m)

FLD+ Lens 0.75 - 1.13 : 1 (WUXGA) (EN46) (0.7 - 7m)

FLD+ Lens 0.75 : 1 (WUXGA) (EN42) (0.7 - 7m)

FLD+ Lens 0.75 - 1.13 : 1 (WUXGA) (EN45) (5 - 30m)

FLD+ Lens 1.12 - 1.58 : 1 (WUXGA) (EN43) (1.5 - 15m)

FLD+ Lens 1.58 - 2.33 : 1 (WUXGA) (EN41) (1.5 - 15m)

FLD+ Lens 2.33 - 4.3 : 1 (WUXGA) (EN44) (2.5 - 25 m)

11.00

10.00

9.00

8.00

7.00

6.00

5.00

4.00

3.00

2.00

1.00

0.00

13.00

12.00

11.00

10.00

9.00

8.00

6.00

5.00

4.00

3.00

2.00

1.00

0.00

Image 4-6

Projection distance

4.8 Scheimpﬂug (Boresight) adjustment

What is Scheimpﬂug?

The lens holder has to be adjusted s o that the “sharp focus plane” of the projected image falls together with the plane of the screen (Fp1→Fp2). This is achieved by cha plane comes to the DMD plane the further the sharp focus plane will be. It can occur that you won’t be able to get a complete f ocused image on the screen due to a tilt (or swing) of the lens plane with respect to the DMD plane. This is also know n as Scheimpﬂug’s law. To solve this the lens plan remove the tilt (or swing) between lens plane and DMD plane (Lp3→Lp4).

Lp1

Lp2

DMD

Image 4-7 Scheimpﬂug principle

nging the distance between the DMD plane and the lens plane (Lp1→Lp2). The closer the lens

e must be placed par allel with the DMD plane. This can be achieved by turning the lens holder to

Fp1

SCREEN

Fp2

DMD

Lp3 Lp4

(Scheimpflug)

Fp4

Fp3

SCREEN

44 601–426 F70 SERIES 18/04/2018

4. Physical Installation

Scheimpﬂug principle

The "plane of sharp focus" can be changed so that any plane can be brought into sharp focus. W hen the DMD plane and lens plane are parallel, the plane of sharp focus will also be parallel to these two planes. If, however, the lens plane is tilted with r espect to the DMD plane, the plane of sharp focus will also be tilted according to geometrical and optical properties. The DMD plane, the principal lens plane and the sharp focus plane will intersect in a line be low the projector for downward lens tilt.

Scheimpﬂug adjustment points

Scheimpﬂug adjustment points are located on the lens mount. The F70 has three (3) set screws and three (3) adjustment screws.

When to apply Scheimpﬂug?

Scheimpﬂug correction procedures may only be carried out by suitably trained and experienced tech nicians.

A Scheimpﬂug correction should only be applied when the overall focus of the projected image is not equally sharp (for example, if the projector is NOT in parallel with the screen or as a result of a previously misaligned Sc heimpﬂ ug). Be aware that the consequence of applying Scheimpﬂug correction upon a screen not in parallel with the projector is that the projected image differs from the rectangle shaped image. In other words “distortion” of the projected image occurs. Masking will be required to solve the distortion.

The disadvantage of Masking is loss of content. T herefore it is st rongly recommended to place the projector in parallel with the projection screen and use the SHIFT functionality of the Lens Holder to match the projected im age with the projection screen. If the SHIFT range is not sufﬁcient then the projector can be tilted and Scheimpﬂug can be applied.

4.9 Scheimpﬂug adjustment procedure

CAUTION: A Scheimpﬂug adjustment should only be carried out by properly qualiﬁed and experienced pro-

jection specialists. A poor Scheimpﬂ ug adjustment may result in an extremely degraded image and will require factory—servicing to the projector.

Necessary tools

• Allen key, hex size 4

• Allen key, hex size 6

Preparation

1. P repare the test area. Barco recommends a projector-screen d istance of 2 metres be used for all Scheimpﬂug adjustments.

Verify that the throw ratio of the installed lens matches the requirem ents of the installation ar ea (projection distance and screen size).

2. Check that the lens is correctly installed, and lens shift is in centre position.

3. If the installed lens has Iris control, open the Iris a

4. O pen the focus ring all the way up.

5. G o to Main Menu / Test Patterns / Full Screen and select to display the Focus test pattern.

6. Z oom the lens to its widest opening (maximum image size on the screen).

Apply a Scheimpﬂug correction

1. L oosen the three set screws (reference 1b, 2b, 3b). Use a size 6 hex key to do this.

ll the way up.

601–426 F70 SERIES 18/04/2018 45

4. Physical Installation

Image 4-8

2. A djust the left side Scheimpﬂug adjustment screw (reference

1) until the test image in the top right side of the screen is in focus.

Useasize4hexkeytodothis.

Note: This proc ess may cause the other areas of the image to slide out of focus . This is totally normal.

Image 4-9

3. A djust the right side Scheimpﬂug adjustment screw (reference 2) until the test image in the top left side of the screen is in focus.

Useasize4hexkeytodothis.

Note: This proc ess may cause the other areas of the image to slide out of focus . This is totally normal.

Image 4-10

4. A djust the top Scheimpﬂug adjustment screw (reference 3) until the test image in the bottom half of the screen is in focus. Use

asize4hexkeytodothis.

Note: This proc ess may cause the other areas of the image to slide out of focus . This is totally normal.

Image 4-11

5. Continue adjusting the screws one at a time until the test image is uniformly sharp across all areas of the display.

6. Test the focus by zoomin

g out (minimum image size on screen) and then zooming in again. Verify the image is still sharp. If there

are any deviations to sharpness, repeat steps 2 to 6 until the image is correct.

7. Tighten the three set screws in the following order: left (1b), right (2b) and then top (3b). Use a size 6 hex ke y to do this.

601–426 F70 SERIES 18/04/2018

5. GETTING STARTED

About this chapter

This chapter describes how to set up and optimize your projector setup when the physical installation process is complete.

Overview

• Projector source and control connections

• Power up the projector

• Power down the projector

• Power m ode transitions

• Power m odes

• Customize projector settings

• User interface

5.1 Projector source and control connections

Overview

• Making connections

• Connector spec iﬁcat ion s

• Control interfaces

5. Getting started

5.1.1 Making connections

The source switching time varies from 0.5 to 5 seconds.

Source signal connectivity

The connector panel at the back of the pr ojector is used for all source connections.

Source signal connectivity on the projector is:

• 2x Dual Link DVI-I (DVI-D functionality)

• 2x DisplayPort 1.2

• 1x HDM I 2.0

• 1x HDB aseT

•1x3GSDI

5.1.2 Connector speciﬁcations

Overview

•DVI-I

• Display Port 1.2

• HDMI 2.0

•3G-SDI

• HDBase T

5.1.2.1 DVI-I

Speciﬁcations

Parameter Value

Connector DVI-I female digital RGB

Signal characteristics DVI 1.0, Digital, TMDS

601–426 F70 SERIES 18/04/2018 47

5. Getting started

Parameter Value

Max. cable length

Max. pixel rate

Scan format

Max. input data resolution

Bit depth 8 bit

EDID

HDCP Supported

25 m (24 AWG)

330 MHz (dual link), 165 Mhz (single link)

Progressive

1920x1200 60Hz (Single link), 2560x1600 60Hz (Dual Link).1920x2400 @60Hz

Supported

5.1.2.2 Display Port 1.2

Speciﬁcations

Parameter Value

Connector Standard Display port

Signal characteristics

Functionality Mandatory

Max. cable length

Supported Link Rate RBR, HBR1, HBR2

Scan format Progressive

Max. input data resolution 2560x1600@120Hz WQXGA / 3840x2400 @60Hz (4K ) Max

Bit depth 8, 10, 12 bit

EDID Supported

DP 1.2

15m(24AWG)-RBR;

2m(24AWG)–HBR1,HBR2

5.1.2.3 HDMI 2.0

Speciﬁcations

Regarding HDMI 2.0: The decryption protocol HDCP 2.2 are enabled and valid in this unit.

Parameter Value

Connector Standard HDMI

Signal characteristics Digital, T MDS

Max. cable length 15 m (24 AWG)

Max. pixel rate 594MHz

Max. input data resolution 3840x2160 @60Hz

Bit depth 8, 10, 12 bits

EDID Supported

HDCP Supported

Ethernet No

Audio return No

48 601–426 F70 SERIES 18/04/2018

5. Getting started

5.1.2.4 3G-SDI

Speciﬁcations

Parameter Value

Standard SMPTE 424M-2006 10bit level A

Connectors 1x) BNC 75 o hm type IEC 60169-8, Amendment 2 1997, A

Bandwidth >3 GHz

Return loss >10dB at 3GHz

Impedance 75 ohm resistive

5.1.2.5 HDBase T

Speciﬁcations

Parameter Value

Reference speciﬁcation HDBaseT 1.0 Speciﬁcation, June 2010

Connector Standard RJ-45, 8P8C

Signal characteristics

Max. cable length (1080p/48b/60Hz) 100 m (Cat5e/6), Pixel Clock <=225HHz , Video Datarate

Max TMDS Clock Frequency

Max video resolution supported

HDCP Pass-Through Yes, from Source to Projector

IR Extension

RS-232 Extension Not Supported

10/100Mbps Ethernet Pass-Through Not Supported

Fallback to 100B aseT x, IEEE 802.3u

USB Ove r Centre Tap Not Supported

Power Over Ethernet Not Supported

Audio

LEDs - HD Base Status Operation: Green, Left

HDBaseT

<=5.3Gbps

70 m (Cat5e/6), Pixel Clock >225HHz, Video Datarate >5.3Gbps

100 m (Cat6a/7), Pixel Clock >225HHz, Video Datarate >5.3Gbps

270 MH z

1920x1200 @60Hz (WUXGA 60Hz)

Not Supported

Link/Mode: Yellow, Right

5.1.3 Control interfaces

About

The following control interfaces are available on the projector:

• 1x RS -232 (for projector c ontrol)

• 1x LAN/Ethernet (for projector control

• 3x USB-A ports

Overview

• RS-232

• LAN/Ethernet

• USB-A port

601–426 F70 SERIES 18/04/2018

5. Getting started

5.1.3.1 RS-232

Speciﬁcations

Parameter Value

RS-232 connector 1 female DB9 connector (RS232-in) for projector control and

debug

5.1.3.2 LAN/Ethernet

Speciﬁcations

Parameter Value

Ethernet connector

Protocols

Speed 10/100 Mbit/1000Mbit

1 RJ45 Connector for projector control (not content)

DHCP, TCP/IP, UDP/P

5.1.3.3 USB-A port

Speciﬁcations

Parameter Value

USB connector

Function

Power

Standard USB 2.0

Type A

Firmware upgrade using USB sticks

Power 5V, max 1,5A (out)

5.2 Power up the projector

CAUTION: Sources should always be connected before the projector is powered up

CAUTION: Use only power cords following the unit, designed for your projector model. Do not use unautho-

rized replacements. Do not use power cords which are damaged.

Power up the projector using the keypad or remote

1. Connect the line cord to the projector.

2. P lug the 3–pronged cor d into a ground ed AC outlet.

The projector will b egin warming up, and the backlight of the Standby /power button are ﬂashing white.

3. W he n the backlight on the standby button are constant white, the projector are in standby mode, ready to be switched on.

4. P ress the standby button on the keypad or the

The power button backlight on the keypad will ﬂash blue w hile the projector is warming up.

5. W he n the power button bac klight is steady blue, the projector is ready for use.

power button on the remote to bring the projector up to on mode.

5.3 Power down the projector

Power down using the keypad or remote

1. D epress and hold the pow er button on the keypad or remote for four (4) seconds.

The Pr ojector is now in cooling down phase.

2. W he n the projector pane l is no longer illuminated, remove the mains power cord from the projector.

601–426 F70 SERIES 18/04/2018

5. Getting started

5.4 Power mode transitions

5.4.1 General

Transition Diagram

This diagram shows all m odes available on the projector (un plug, ON, READY, ECO), and the actions necessary to change m ode.

Image 5-1

Projector mains powered

Auto transition after x minutes if ECO mode enables

Press power On/Off button, remote On/Off button

ECO

READY

50%

5.4.2 Power on projector

If not already connected, connect the female side of the power cord with the power input socket of the projector. For more details see section de

The background image of the startup screen and info screens can be changed with Projector Toolset with an installed F70 / F90 se ries plug-in.

dicated to the power co rd installation.

Description

Plug the 3-prong plug of power cord into a grounded AC outlet. The projector will go to READY mode. During this stage the system boots and performs the internal check of the boards. The Power On/Off button will BLINKING WHITE until READY mode is achieved. Once in READY mode, the Power On/Off button will be lit WHITE.

5.4.3 Going from READY to ON

Description

Press the Power On/Off button on the projector, or the Power On button on the remote control. The projector will power ON.The Power On/Off button will BLINK BLUE during the transition from READY to ON. Once the projector is on, the Power On/Off button

will be lit BLUE.

601–426 F70 SERIES 18/04/2018

5. Getting started

5.4.4 Going from ON to READY

Description

Press and hold the Power on/off button on the projector for 3 seconds, or press the Power Off button on the remote control. The projector will power down through a cool down phase. The Power on/off button will BLINK WHITE during the transition from ON to

READY. Once the projector is in RE ADY,thePower on/off button will be lit WHITE.

5.4.5 Going from READY to ECO standby

Description

If ECO Standby mode is enabled in the service menu (refer to the section "GUI - system settings/Standby ECO", in User Guide) the projector will automatically go to ECO standby mode after a time-out (default 15 minutes). A ll elect go down except for a very small wake up controller. The Power on/off button will FLASH WHITE every s econd.

ronics (including fans, pumps,...)

5.4.6 Going from ECO to ON

Description

Press the Power on/off button on the projector, or the Power On button on the remote control. The projector goes from ECO directly to ON. The projector will go through the same booting phase as on power plugging, then do the transition from READY to ON.Of course startup-time will be longer then from READY to ON.

5.4.7 Wake On LAN (WOL)

About

The projector has WOL functionality, that can be used for the project for transition from READY to ON.

The WOL is performed by sending a Mag ic Packet followed by the projectors MAC address. The MAC address is f ound in the menuHome / System settings / Communication / LAN. The MAC address is similar to the HW address that is shown in this menu path.

or to go from ECO mode to READY mode. Use a json command

5.5 Power modes

General

The table below details the F70 power modes.

Mode Description

Normal Projector is booted up and t he light source is on

Ready

ECO Standby Light source is switched off and projector elect

Projector is booted up but the light source is off

powered down

5.6 Customize projector settings

About

The projector display, behavior and user interface can be adjusted to meet individual requirements.

Options include:Home/System Setti

• Adjust the OSD menu color

ngs/Themes

5.7 User interface

ronics are

Overview

• On S creen Display (OSD)

601–426 F70 SERIES 18/04/2018

5. Getting started

5.7.1 On Screen Display (OSD)

About

The pro jector on screen display (OSD) is the primary user interface (UI). From here, you can review and adjust all projector and display settings.

The OSD interface uses tabs to display the main men u. Topics are t hen further sorted and displayed by function: main (topic) — sub (function) — sub (function).

There are six main menu tabs: Source, Image, Installation, System settings, Test pattern and Status.

The OSD can be d isabled by pressing the OSD on/off button.

In order to show the OSD, the OSD O n/Off button must be disabled. (White backlight on the button). When the button have blue illumination, the OSD will not appear, and the display information are only visible on the LCD Display. Only Critical warn ings will be displayed.

User access levels

The projector’s software platform uses access levels to deﬁ ne what each user can do.

There are two user access levels: S tandard User and Power User. In addition, there is a Service user access for certiﬁed Service personnel.

A standard user has access to all projector functionality and OSD menu items. A power user has, in addition to access to all p rojector functionality and OSD menu ite ms, access to a number of advanced functions. Access to power user features is password-protected. Contact your projector supplier for more information.

Navigation

You can navigate the OSD using the local keypad or the remote c ontrol.

Press the MENU button to display the OSD. (The OSD must be enabled, press O SD button to enable.)

Use the arrow key s to navigate left, right, up and down.

Press the OK b utton to select a menu topic and get more options.

Use the numeral keys to enter values, or use the arrow keys to move the barscale up or down.

Press ME NU again to exit the menu system.

Press the OSD button to deactivate the O SD on the screen. Only critical warnings

Some menu options are reserved for Po wer or Service Users; these will be grayed out and not available for selection w h en in standard user mode. To access these fe atures, enter your Power or Service Code in the Service Menu or contact your support representative for more information.

will be displayed.

Deﬁne values

Menu settings ar e displayed using checkboxes, barscale sliders, and drop-down lists.

To set a value :

• Press OK to select or deselect a c heckbox (turn a function O N or OFF).

• Use the arrow keys to move the barscale slider up or d own on the value line. For a barscale 0-9, each s tep will equal 10% of

the total value.

• To enter the value as a direct number, press ENTER, input th e digit(s), and then Press ENTER again to execute and exit cursor

mode e.g. ENTER 79 ENTER.

Changes to values are implemented dynam ically.

Menu memory

The OSD menu remembers the last selected sub–item as long as the projector is running. The menu memory is reset when restarting the projector from standby.

601–426 F70 SERIES 18/04/2018

5. Getting started

54 601–426 F70 SERIES 18/04/2018

6. Source menu

6. SOURCE MENU

About the Source menu

This menu is used to select, review and con ﬁgur e sources into the projec tor. Enables either via the source menu, or the shortcut key.

By navigate through the Home/Source m enu, it will be visible also on the OSD.

By using the shortcut key, the menu occurs only on the LCD display.

Overview

• Connector selection

• Connector Settings

• Using Dual inputs

6.1 Connector selection

About

Home/Source

Image 6-1 Source Menu. (Scroll for more choices).

Click on the relevant input connector icon to swap or activate the source.

The icon for the active source is highlighted.

The list of displayed sources can be adjusted to include other connectors.

The default selection of connectors displayed is:

• Display Port 1

• Display Port 2

• Dual Disp layport Columns

• Dual Displayport Sequential

•DVI1

•DVI2

• Dual D VI Columns

• Dual D VI Sequential

• HDBaseT

• HDMI

•SDI

6.2 Connector Settings

About Connector Settings

The Connector Settings menu allows you to change settings for each input connector of the projector.

By default all options for every connector are set to automatic, together with the native Extended Display Identiﬁcation Data (EDID).

601–426 F70 SERIES 18/04/2018 55

6. Source menu

When entering the menu for each input connector, you can change the following:

• Color Space

• Signal Range

•EDID

How to conﬁgure a connector

1. P ress Menu to activate the menus and s elect Source.

Image 6-2 Select Source

2. P ress OK.

The Select Source menu is displayed w ith the actual available sources ﬁlled out.

3. S croll down to the bottom of the list of available sources and select Connector Settings.

Image 6-3 Source menu, Connector Settings

The available input connectors are displayed.

Image 6-4 Select source

4. S elect the desired connector.

The Con ne ctor Setti ngs menu for this connector will be displayed.

601–426 F70 SERIES 18/04/2018

Image 6-5 Example of connector settings for an HDMI connector

5. You can change the following:

- To force a limit on the color space, select one of the available color spaces.

- To force a limit on the used s ignal range, select one of the available signal ranges.

- To set a video timing other than the one native for the connector, select one of the options under EDID.

Note: You cannot change the EDID for SDI connectors.

6. Source menu

6.3 Using Dual inputs

Dual Input.

For extended ﬂ exibility to connect high resolution sour ces with a pixel clock over 330 MHz, the projector is supporting a dual input mode. In this mode, the left and the right half of the image can be connected to the DVI-1 and DVI-2 respectively, or DP1 and DP2.

To enable this mode, select the source that ﬁts in the m enu Home/Source

Dual input modes

There are four ways to connect dual input.

• Dual Disp layport Columns

• Dual Displayport Sequential

• Dual D VI Columns

• Dual D VI Sequential

For Images to be displayed in this mode, the resolution must be the same on both channels

Signal source setup.

When using dual inputs, it is important that the signal sources are set up correctly, with the correct resolution. Please refer to the manual for the source itself (PC, Graphic driver card..) in order to obtain a correct setup. If the setup is wrong, no picture will be visible in dual mode.

The resolution for each dual column channel can be up to 1920x2400 pixels.

The resolution for each du al sequential channel can be up to 3840x2400 pixels. (4K)

Change the EDID for each channel to the correct value. See "Connector Settings", page 55 for EDID setup.

601–426 F70 SERIES 18/04/2018 57

6. Source menu

2400

Image 6-6 Dual Column Setup

3840

1920 1920

Dual Column Input 2Dual Column Input1

2400

Dual Sequential Input1

2400

Image 6-7 Dual sequential setup.

3840

Dual Sequential Input 2

2400

58 601–426 F70 SERIES 18/04/2018

7. Image menu

7. IMAGE MENU

Overview

• Contrast

• Brightness

• Saturation

• Sharpness

• Gamma Adjustment

• Advanced im age adjustments

About Image adjustment menus

There are different menu pictures showing up for the LCD display and the OS D. For the LCD display, the menu is shown below. The OSD menu is shown in the different topics below, and is visible in the lower left corner of the screen. The operation of the menus can be done with both the remote control or the arrows on the keypad. It is also possible to switch between the different adjustments by using the up and down arrows, instead of exit one menu and then enter the next o ne.

Image 7-1 Main Image menu.

Image 7-2 Image sub menu visible on the LCD.

7.1 Contrast

About

Image / Contrast

Used to adjust the contrast ratio of the displayed image by applying ga in to the red, green and b lue signals.

Available range: 0.00 to 2.00

Default value: 1.00

601–426 F70 SERIES 18/04/2018

7. Image menu

Image 7-3 Contrast OS D menu

When inside this menu, it is possible to change to the other image adjustments (Brightness, Saturation, Sharp ness and G amma) by using the up a nd down arro w s on the remote control or keypad.

7.2 Brightness

About

Image / Brightness

The brightness function is used to adjust the black level in the input picture. It adds or subtracts an offset, or bias in to the red, green and blue signals.

Available range: –1.00 to 1.00

Default value: 0.00

Image 7-4 Brightness OSD menu

7.3 Saturation

About

Image / Saturation

Saturation levels impact on the white levels and the intensity of the color display ; the higher the value, the more vivid the color display will be.

Available range: —1.00 to 2.00

Default value: 1.00

601–426 F70 SERIES 18/04/2018

7. Image menu

Image 7-5 Saturation OS D menu

7.4 Sharpness

About

The s harpness adjustment ampliﬁes the high frequency components in the picture, meaning that by increase the sharpness, the picture will be perceived as sharper, and if decreased, the picture will be perceived as more blurry.

Increasing the sharpness will have the best effect in high contrast images, eg a table with text and borders.

In a natural picture, high sharpness can be perc eived as noise, as all details in the picture will be ampliﬁed.

Available range —2 to 8.

Default value: 0

Image 7-6 Sharpness OSD menu

Image 7-7 Effect of sharpness adjust

7.5 Gamma Adjustment

About Gamma correction.

Gamma compensation, or gamma correction, is a way of adjus ting the signal input to light output characteristics of a display or projector in order to suit the eye’s sensitivity to different light levels and to compensate for non-linearities in displays. Without gamma compensation, images may look too dark or too bright, lack detail or depth. By adjusting the amount of gamma compensation changes, you change only the perceived brightness levels.

Different types of displays have dif example, an MS Windows generated image displayed on a CRT monitor will require a gamma c orrection value of about 2.5 to avoid color bleaching and burning.

ferent gamma factors that need to be corrected in order to look and be perceived the sam e. For

601–426 F70 SERIES 18/04/2018

7. Image menu

The gamma curve correction formula is based on output level ∝ input level ^ gamma.

1. E nter the menu Home/Image, and select Gamma.

2. Use the arrow keys to adjust the Gamma value, until the colors seems to be perceived correctly. The default value is 2,2.

Image 7-8 Gamma OSD menu

7.6 Advanced image adjustments

7.6.1 P7 Realcolor

Purpose

When blending images from multiple projectors, the perceived color c oordinates of each projector can be altered to a desired com mon level, so that the projected colors are identical over all p rojectors used.

Alternatively, if you are unfamiliar with how adjusting the Colors to a spec iﬁc setting, there are also a certain number of presets available, which forces the color output to speciﬁc c olor standards.

The selection of the presets w ill vary, depending on the projector type, and the color wheel installed.

How to choose one of the P7 presets

1. In the main men u, select Image → Advanced → P7 Realcolor.

Image 7-9 Advanced menu — P7 Realcolor

Image 7-10

The P7 menu is d isplayed.

601–426 F70 SERIES 18/04/2018

Image 7-11 P7 Realcolor menu

2. C hoose one of the pre-deﬁned p resets:

- Native: Projector native color s ettings. Default setting

- EBU: European c olor standard for broadcasting

- SMPTE-C: American color standard for broadcasting.

- Rec. 709: Color standard for high-deﬁnition televisions (HDTV).

7. Image menu

Image 7-12

Note: When choosing one of the presets, All o ther options in the P7 menu are disabled.

How to set custom P7 values

1. In the main men u, select Image → Advanced → P7 Realcolor.

Image 7-13 Advanced menu — P7 Realcolor

The P7 menu is d isplayed.

Image 7-14 P7 Realcolor menu

601–426 F70 SERIES 18/04/2018 63

7. Image menu

2. S elect the desired Mode. Choose one of the following custom options:

- Custom RGB: 3–point c olor conﬁguration.

In RGB mode, the C, M and Y coordinates will be calculated automatically based on the R , G and B coordinates.

- Custom RGBCMY: 6–p oint color conﬁguration (both RGB and CMY).

In RGBCMY mode, each color can be given a speciﬁc coordinate within the measured color triangle.

- Custom WHITE:Conﬁ gure only the White temperature.

3. D eﬁ ne the coordinates for each available color.

Click on a coordinate value and select the current value. Enter the desired value with the numeric keys.

Note: You can only pick coordinates within the measured color triangle.

4. F or Custom White, click on White point and choose one of the following:

- Coordinates:Conﬁ gure the white point via speciﬁc coordinates.

The white point is speciﬁed us ing an x, y coordinate in the CIE 1931 Chart.

- Temperature:Conﬁgure the white point via a color temperature s lider.

The white point is speciﬁed on a Kelvin scale between 3200K and 13000K tracking along the black body curve.

You can reset all coordinates to the default values (to native) by selecting Reset modes to native. Press OK button to reset.

7.6.2 Edit the RealColor presets.

Editing presets

The different presets in the Real Color menu can be edited to obtain an optimal rendering of the picture.

Enter the menu Home/Image/Advanced/P7 Realcolor.

Select the desired preset mode (EBU, Rec 709 or SMPTE-C) and select the coordinate w ithin each color component that has to be corrected. Enter the desired v alue by the numeric keys or the a rrow key on the remote control.

The values are stored for the preset, until the “Reset” button is enabled, or when a factory reset is performed.

There is also a possibility to store the v alues in the custom presets.. Press the “Copy preset to cu stom” button to save.

The edited presets can be reset to the original values by enter the Reset button. There is also a possibility to copy the values to the custom preset.

To reset the v alues in Custom presets, enter the “Reset to n ative” button when in Custom mode

Image 7-15 Change coordinate values.

64 601–426 F70 SERIES 18/04/2018

Image 7-16 Reset the edited values to original

7. Image menu

Image 7-17 Reset the custom values to original

7.6.3 Output Resolution 4K

About

With this function, the projector output resolution can be c hanged between 4K U HD resolution and WQ XG A resolution.

Refer to "Projector source and control connec tions", page 47 regarding use of input sources in 4K mode.

Image 7-18 Output resolution menu

7.6.4 Smear Reduction

About

Smear is a phen omenon that typically occur when objects in the picture moves in high s peed over the screen. It appears like there is a “tail” behind the object, or a lag in the moving parts of the picture.

In order to avoid this, there has been developed a Smear Reduction Process (SRP the option that give the best result.

), that reduces this perceived rendering. Select

601–426 F70 SERIES 18/04/2018

7. Image menu

Image 7-19 SRP Menu for WQXGA

SRP Half Plus

Image 7-20 SRP Menu for WQXGA

Image 7-21 SRP Menu for 4K and WQXGA@120Hz.

This menu s are only valid for projectors with COLO R colorwheel. For BRIGHT colorwheel, there is no menu choices in the SRP menu, only SRP-Off.

(See tables below).

7.6.5 Brilliantcolor

About

Changes the color rendering, by adding secondary colors. This has the effect of increasing the color intensity, and by that also the perceived light intensity.

Enter the menu, and select the option that give the best result

601–426 F70 SERIES 18/04/2018

7. Image menu

Image 7-22

This menu is only valid for COLOR colorwheel in W Q XGA @ 60Hz mode. For BRIGHT colorwheel, there are only two choices in the menu; Off and Native.

(See table below)

Menu choices of SRP and Brilliant Color m atrix with COLOR colorw heel installed.

Valid when COLO R colorwheel is installed.

Mode

WQXGA @60Hz

WQXGA@120Hz / 4K mode

SRP Brilliant Color

SRP Off

SRP Half Plus

SRP Off

SRP Half Plus

Off

Native

Video

OffSRP Half

Native

OffSRP Full

Native

Off

Native

Video

Graphics

OffSRP Half

Native

Off

Native

Video

Native

Off

BSI (Black Sub Frame Insertion)

4K @ 60Hz

601–426 F70 SERIES 18/04/2018 67

SRP Half BSI

SRP Half Plus BSI

Video

Graphics

Native

Off

Native

Off

Video

7. Image menu

Menu Choices

Menu choices of SRP and Brilliant Color matrix with BRIGHT colorwh eel installed.

Mode

SRP Brilliant Color

WQXGA @60Hz

WQXGA@120Hz / 4K mode

4K @ 60Hz

Off

BSI

Off

Native

Off

Native

Off

7.6.6 HDR – Perceptual Quantizer (PQ)

About PQ

Perceptual Quantizer (PQ ) is an electro-optical transfer function (EOTF) that allows for the display of High Dynamic Range (HDR) content with a lum inance level of u p to 10 000 cd/m² and can be used with the Rec. 2020 color space.

If your provided HDR content has been mastered with PQ (e.g. Dolby Vision or HDR10), you can adapt the luminance on screen to adapt to the provided content.

For optimal display of HDR content, this is just one value that will inﬂuence the projected image. W hen entering the desired screen luminance, take into account the distance of the projector to the screen an d the quality of the screen used.

How to set the PQ?

1. In the main menu, selec t Image → Advanced → PQ.

Image 7-23

The PQ menu is displayed

Image 7-24

2. Select the desired Unit (nits or foot-lambert).

3. E nter the Screen luminance (either in nits or foot-lambert).

7.6.7 HDR Status.

When an active source is HDR, an

The HDR icon will also be visible in the “Source signal popup” icon in the lower right co rner on the screen.

icon is visible in the status menu.

601–426 F70 SERIES 18/04/2018

Image 7-25 HDR Icon.

Image 7-26 Source signal popup icon.

7. Image menu

601–426 F70 SERIES 18/04/2018 69

7. Image menu

70 601–426 F70 SERIES 18/04/2018

8. Installation menu

8. INSTALLATION MENU

Overview

• IR / Night vision functionality

• Lens

• Orientation

• Warping

• Blending

• Illumination

• CLO – constant light output

• Display Setup

8.1 IR / Night vision functionality

About

IR / Night Vision functionality is only available for the FS variant of the projector..

In combination with Night Vision Goggles (NVG), this will give a realistic r endering of the environment. This will visualize in a realistic way, night time, dusk and dawn, and limited visibility scenarios.

The IR light source has a wavelength of 740nm

How to enable IR/Night Vision.

Enter the menu Home / Installation / Display setup and s elect NightVision in the scroll down menu.

Image 8-1

To set up the IR illumination, enter the menu Home/Installation/Illumination/Power. This menu shows two sliders; one for the Laser, and one for the IR LE D. The s liders are scaled from z ero – 100% power.

601–426 F70 SERIES 18/04/2018 71

8. Installation menu

Image 8-2

Image 8-3

Select the Laser slider, a nd move the slider to the left by the arrow keys to nearly 0% to reduce the laser intensity. (Daylight visibility). By this, the IR LED will be dom inant, and the image on the screen will be visible with the Night Vision Goggles. Put on the goggles, and adjust the IRLED slider to obtain an optimal night vision rendering.

Image 8-4

By mixing the intensity (power) of both the laser and the IR LED, it is also possible to simulate other visibility scenarios, such as evening / early night vision.

601–426 F70 SERIES 18/04/2018

Image 8-5

8.2 Lens

About

Installation / Lens

Manage lens functions: focus, zoom, shift, and iris.

All changes occur dynamically.

Focus and zoom

Installation / Lens / Zoom

Use the navigational arrows, up and down, to adjust zoom .

Use the navigational arrows, left and right, to adjust focus.

8. Installation menu

Shift

Installation / Lens / Shift

Use the left, right, up and down navigational arrows to adjust the lens shift in four directions.

Iris

Installation / Lens / Iris

Use the left and right arrow to c lose / open the iris inﬁnitely between open and closed position .Pr ess and hold to adjust

8.3 Orientation

About

Installation / Orientation

Rotate the image on the imaging device depending on the physical installatin of the unit.

There are four installationoptions, as illustrated below:

• front/table

• front/ceiling

• rear/table

• rear/ceiling

Default: Table Front.

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-6

How to set the correct orientation

Select Orientation from the menu

Image 8-7 Orientation menu path.

The o rientation menu is displayed

Image 8-8 Orientation Menu

Use the arrow keys to select the M ounting and Projection positions, and press OK button to activate.

8.4 Warping

8.4.1 About Warping

About

Image warping is the pro perpendicular alignment of the projector versus the screen. The image will then typically oc cur as shown inim age 8-9.

While an im age can be transformed in various ways, pure warping doesn’t affect the colors.

cess of digitally manipulating an image to compensate for the distortion of the screen, typically by non

601–426 F70 SERIES 18/04/2018

8. Installation menu

Distorted Picture

Ideal Picture

Image 8-9

8.4.2 Warping – On/Off

About warping on/off

By toggling between on and off the warping functionality can be enabled or disabled.

How to toggle

1. In the main menu, select Installation → Warp.

Image 8-10 Installation menu, Warp

The Warp menu is displayed.

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-11

2. In the Warp menu, click Warp to toggle between On and Off.

Image 8-12

Image 8-13

8.4.3 Warping – Screen Size

About (Warp) Screen Size adjustment

If the used screen aspect ratio is different than the projector aspect ratio, e.g. source is 16:9 and projector is 16:10, then black bars will be projected. In the example c ase a black bar on top and bottom of the image will be projected. The warp area contains not only the image inform ation but also the black bars. If we want to position e.g. the active left top corner exactly on the s creen using 4 corner warp , then it is very hard to do that as we are moving the black left top corner and we do not have control over the exact position of image left top corner. By moving the outline of the warp screen size to the active image information, the corner points of the warp area ar e now exactly on the corner points of the active image information and makes warping much easier.

Image 8-14 Warp outline example

How to adjust the image?

1. In the main me nu, select Installation → Warp → Screen Size.

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-15 Warp M enu, Scr een Si ze

The S creen Size menu is displayed.

Image 8-16

2. S elect either Screen width or Screen height.

3. S et the screen size width and height to m atch the me asurement of the screen.

Note: It is only the ratio between the width and height that is used, so the values may be entered as the screen aspect ratio or

actual measurement in c m, inches or any other unit.

Tip: A red border will be projected along with the current image. The border is a visual tool, showing the result of the adjusted

outline.

Tip: The value can also be entered by the nume ric keys on the remote co

the new value by the nume ric keys.

4. Click Apply.

ntrol. Press * to delete existing numbers, and enter

8.4.4 Warp – 4 Corners adjustment

About 4 Corners adjustment

Basically, this type of warping adjusts each o f the four image corners in the X and Y direction, if you have a typical trapezoid picture of the screen as shown below.

To have a successful Warp correction, the size of

Some examples of pictures when the projector axis is not perpendicular to the screen.:

Image 8-17

the screen must be entered. See "Warping – Screen Size", page 76

How to adjust the image.

1. F rom the war p menu, select the 4 Corners Menu. A yellow frame will be visible.

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-18

2. To enable the 4 Corners Warping, Set the Warp slider to the right position. (Select and enter).

3. S elect the corner that must be warped. If need for warping several corners, select and adjust the corners one by one.

Adjust the value by the arrow keys. The value represent the mov ement of the X and Y coordinates for each corner. W hen the warping is complete, exit the menu by using the “Back” button.

Image 8-19

4. If the picture still has a trapezoid shape, warp is not enabled. Select the Installation / Warp m enu, and press enter. The slider

moves to the right, and the w arp status changes to “On”.

Image 8-20

8.4.5 Warping – Bow

About bow adjustment

A bow distortion can be adjusted so that a normal im age is displayed. Positive adjustments angles introduce more outside bow distortion. Negative adjustments introduce more inside bow distortion.

601–426 F70 SERIES 18/04/2018

Image 8-21 Bow distortion

8. Installation menu

Symmetric bow correction

1. In the main menu, select Installation → Warp.

Image 8-22 Installation menu, Warp

2. In the Warp menu, select Bo w .

Image 8-23 Warp menu, Bow

A check symbol at the bottom right corner indicates that the bow function is activated.

3. To enable Bow correction, make sure the Bow slider is set to On.

The slider is enabled when set t

o the right and when it is highlighted blue.

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-24 Symmetric Bow correction.

4. To enable a symmetric adjustment, make sure the Symmetric slider is set to On.

The slider is enabled when set to the right and when it is colored blue.

5. S elect the side of the picture to be bow corrected, conﬁrm by pressing enter, and us e the arrow keys to adjust the angle and

linearity (length) of the vectors. The angle is adjusted by the up and down arrows on the remote c ontrol, and the linearity is adjusted by the left and right arrows. The correction will occur s ymm etrically on each side of the center of the highlighted side. When corrected with the va lues in the image above, the picture will occur as shown below. Repeat this step for all sides of the picture that has to be corrected.

Image 8-25 Symmetric bow corection

Non symmetric bow correction

1. E nter the Bow menu, and disable the s ymm etric slider.

2. T here are now two vectors on each side of the picture that can be adjusted individually. S elect each of them, and adjust angle

and linearity (length) individually to obtain the cor rect correction. The angle is adjusted by the up and down arrows on the remote control, and the linearity is adjusted by the left and right arrows

Image 8-26 Left vector of the upper side of the picture.

80 601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-27 Right vector of the upper side of the picture.

3. W he n corrected with values in the illustrations above, the picture will occur as shown below. Ob serve that the upper side of the

picture now has an asymmetric correction.

Image 8-28 Asymmetric bow correction

4. R epeat the step for each side of the picture that must be corrected.

Deﬁnition of angle and linearity (length) in the bow warp procedure

Image 8-29

To reset the bow adjustments, select Reset and press the OK button.

601–426 F70 SERIES 18/04/2018 81

8. Installation menu

8.4.6 Warping – Warp ﬁles

About custom Warp Fil es

Next to setting your speciﬁc warp conﬁguration in the GUI, you can also upload or download a custom warp grid in XM L format to/from the projector. This is a time-saving option when multiple projectors need an identical Warp conﬁguration.

To upload or download warp ﬁles you can use P rojector Toolset or Prospector tool to upload/download the w arp grid in the format of an XML ﬁle. Alternatively, you can contact the “ﬁle endpoint” directly via the curl program or some other tool that supports http upload.

For more information on uploading/dow nloading Warp ﬁles using the Projector Toolset, refer to the Projector Toolset user manual.

For more information on uploading/downloading Warp ﬁles using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

HowtoactivateanuploadedWarpgrid?

1. In the main menu, select Installation → Warp.

Image 8-30 Installation menu, Warp

2. In the Warp menu, select Files.

Image 8-31 Warp menu, Files

The Warp Files menu is displayed.

Image 8-32

3. If any custom Warp ﬁles are available, select the desired wa rp ﬁle.

601–426 F70 SERIES 18/04/2018

Image 8-33

4. Click on the on/off button on top to activate the selected warp ﬁle.

8. Installation menu

Image 8-34

8.4.7 Warping – Latency control in a multi projector setup

Transport latency

The added delay in the image processing c hain. The value is the number of lines relative to the output resolution.

Latency

The total time from the ﬁrst pixel is coming in on an input source, until the ﬁr st light representing that pixel is visible on the screen. This includes the transport delay. The value is normally given in m illiseconds.

Functional description

Every projector in a multi–projector setup will have a different latency. Th is latency depends on the amount of warp and on the frequency of the projected image. In order to have no visible difference in the overall projected image, the user needs to be able to control the latency of each projector.

The latency v alue can be read ou t in the status menu for each individual projector.

How to conﬁgure transport delay?

1. Read out and note the latency of each projector in the multi-projector setup. You can ﬁnd this latency under Transport delay in

the status menu for each p rojector.

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-35 Example of the latency readout

2. Identify the projector with the longest delay.

3. F or each projector in the setup, select Installation → War p in the main menu.

Image 8-36 Installation menu, Warp

4. In the Warp m enu, select Transport Delay.

Image 8-37 Warp menu, Transport delay

The Transport menu is displayed.

Image 8-38

5. E nter the value either by the arrow k eys (one step at a time) or directly by the numeric keys on the remote control.

6. Enter “Apply” to conﬁrm the value.

7. Repeat this process for every projector in the setup.

601–426 F70 SERIES 18/04/2018

8. Installation menu

8.5 Blending

8.5.1 Basic Blend

About

When two projectors are used together to make one picture on the screen, the blend function must be activated. This blend function ensures a seamless transition of the images between the two projectors.

The principle is that the light intensity in the blend zone from each projector will be adjusted individually, so that the rendering on the screen are perceived as from one projector.

The blend function can be enabled for both pictures over/under, and pictures side by side.

The blend will not be affected by the projector’s warp.

Width, Projector 2Width, Projector 1

Picture frame Projector 1

Overlap / Blend Zone

Image 8-39

Picture frame Projector 2

The Mask adjustments.

The offset adjustments are used to cut the image on each side. Normally used to hide parts of the picture that shall not be shown on the screen. An example can be: If the source is a pc, you may want to hide the m enu bar at the bottom of the screen.

8.5.2 Set up the system

How to set up the system

In this chapter, the setup procedure for the projectors is explained, but a setup procedure must also be performed for the picture source.

In order to obtain a satisfying result for the Blend function, the overlap / Blend zone are recommended to be at least 10% of the p icture width.

The basic principle is that the overlap setup in the source shall correspond with the blend width setup for the projector. That means that if the overlap zone for the source is set to 500 pixels, the width of the blend zone for the projector also must be set to 500 pixels.

First step is to align the image from the projectors as ac curate as possible in a mechanical way, meaning without any optical corrections. A t the same time, establish

Then adjust the remaining irregularities by using the shift and warp features in the projectors to obtain the last ﬁne tuning of the alignment.

Setup the source to a blend which corresponds with the preset overlap on the screen. There are different ways to do this, depending on the source. Refer to the source unit’s manual for this issue.

Adjust the Blend for the projectors as described below.

an overlap in the pictures between the two screens.

8.5.3 Adjustment Procedure

Blend adjustment procedure

Entering the Blend Adjustme nt from the Home menu, either by the remote control, or the keypad on the projector.Home/Installation/Blend And Mask/Blend Mask The menu shown below appears on the OSD.

601–426 F70 SERIES 18/04/2018

8. Installation menu

The “Enable” button enables/disables the blend function. The “Show Lines” enables alignment lines on the screen, in order to visualize the overlap/blend zone.

Image 8-40 Blend adjust menu

Use the up/down/left/right arrow key on the remote control or key pad to n avigate in the m enu.

Blend adjustment procedure. Side by side conﬁguration.

1. S tarting with the left picture: By the arrow keys, place the display cursor on respectively the “Enable” zone and the “Show Lines”

zone and activate them by pressing enter.

2. Use the right arrow key to move the cursor to the “Top Mask” position in the menu. Press enter. From this position the cursor

can be moved around to the desired adjustm ent options.

3. M ove the c ursor to the “Right Width” position and press enter on the remote control.

4. A djust the width value by using the arrow keys up (or down), one step at a time. By pressing the key arrow constantly, the blend

value will increase rapidly. The numeric value of the width is shown on the screen next to the alignment line. (The number entered represent the blend width expressed in number of pixels). Conﬁrm position by pressing enter.

5. F or the right picture, repeat the procedure, but adjust the Left Width instead of the right width. The numeric value for the left width

shall ideally be the same as for the right width for the left picture in the steps abo ve.

6. E xit the menu by using the exit button on the remote control.

Adjustment procedure in over / under conﬁguration.

For Blend adjustments in over / under conﬁguration, the proc height instead, and perform a similar procedure.

edure is the same as for side by side, but use the Top and Bottom

Use the numeric keys instead of the arrow key to set the values.

Instead of adjusting the lines by the arrow keys, the value can also be typed directly using the numeric keys on the remote control.

To remove or undo the entered numbers, use the * key on the remote control.

8.5.4 Black Level Adjustment

About adjusting the black level

The Purpose of the black level adjustment is to adjust the black levels in the non ov erlapped areas with the black level in the overlapped areas (Blend Zone).

This is a necessary function, due to the fact that the black level will be brighter in the blend zones, since multiple projectors will add light in these zones.

The width of the black level area shall ideally be slightly larger than the width of the blend zone in order to also compensate for the “sea of mirrors” phenomenon.

The ﬁgure below shows how this occurs in a side by side conﬁguration without any correction of the blac k level.

601–426 F70 SERIES 18/04/2018

Picture Left Picture RightBlend Zone

Image 8-41

How to adjust the level manually

1. In the main menu, select the Black level menu

8. Installation menu

Image 8-42

2. E nable the ”Black level” and “Show lines” buttons.

Image 8-43

3. M ove the cursor to the side where the overlapped area occurs. (Left/right/top/bottom.) For the left projector, this will be the right

side in the menu. Press enter, and adjust the value with the arrow keys. As mentioned earlier, the value shall be slightly larger than the blend zone offse zone is optimal, press enter. The value can also be entered by the numeric keys in the remote control.

4. M ove the cursor to “Level”, press enter and adjust this level until the black level equals the level in the blend zone.

This value can also be entered by the numeric keys on the remote control.

5. R epeat the same procedure for the other projector,

6. Disable the “Show lines” when the Black lev el adjustment is completed.

t. A line that indicates the zone will also be visible when “Show lines” is enabled. When the black level

601–426 F70 SERIES 18/04/2018

8. Installation menu

8.5.5 Black Level Files

About custom Black Level Files

Next to setting your speciﬁc Black Level Adjus tment in the GUI, you can also upload or download a custom B lack Level adjustment ﬁle in png, jpeg or tiff format to/from the projector.

To upload or download Black Level masks you can use the Prospector tool. Alternatively, you can contact the “ﬁle endpoint” directly via the curl program or some other tool that supports http upload.

For more information on uploading/downloading Black Level ﬁles using the Prospector, refer to the Prosp

For more information on uploading/downloading Black Level ﬁles using curl or other tools that supports HTTP upload, refer to t he Pulse API Reference Guide.

ector user manual.

How to activate an uploaded Black Level adjustment ﬁle?

1. In the m ain menu, select Installation → Blend and Mask → Black Level Files.

Image 8-44 Blend and Mask menu, Black Level Files

The Black Level Files menu is displayed.

Image 8-45

2. If any custom Black Level adjustment ﬁles are available, select the desired ﬁle.

Image 8-46

3. Click on the on/off button on top to activate the selected Black Level adjustment ﬁ le.

601–426 F70 SERIES 18/04/2018

8. Installation menu

8.5.6 Blend Files

About custom Blend Files

Next to setting your speciﬁc Blending conﬁguration in the GUI, you can also upload or download a custom Blend conﬁguration ﬁle in png, jpg or tiff format to/from the projector. This is a timesav ing option when multiple projectors need an identical blending

conﬁguration.

To upload or download Blend mas ks you can use the Prospector tool.

Alternatively, you can contact the “ﬁle endpoint” dire ctly v ia the curl program or some other tool that su

For more information on uploading/downloading Blend ﬁles using the Prospector, refer to the Prospector user manual.

For more information on uploading/downloading Blend ﬁles using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

pports http upload.

How to activate an uploaded Blend conﬁguration ﬁle?

1. In the main menu, select Installation → Blend and Mask → Blend Files.

Image 8-47 Blend menu, Blend Files

The Blend Files menu is displayed.

Image 8-48

2. If any custom Blend ﬁles are available, select the d e sired ﬁle.

Image 8-49

3. Click on the on/off button on

601–426 F70 SERIES 18/04/2018

top to activate the selected Blend ﬁle.

8. Installation menu

8.6 Illumination

About

Home/Installation /Illumination/Power

Review light source status and adjust (dim) laser power from 0 to 100%.

Default: 100%

How to reduce the output light

In the menu, select:

Image 8-50 Illumination Menu.

The actual illumination s etting is indicated in the menu.

Enter the menu, and use the slider to adjus t.

Image 8-51

8.7 CLO – constant light output

About

This function will ensure that the projector regulates its illumination power to maintain the same level of output light during the lifetime of the light source. This requires that the laser power is not set to 100% from the s tart, but to a lower value. The lower this value is set, the longer the projector will manage to maintain the level. This is due to the fact that the light source has a naturally decreasing intensity over time.

Enable CLO

Enter the menu Home/Installati Light Ou tput button..

on/Illumination/Power,set the laser powe r slider to an appropriate v alue, and activate the Constant

601–426 F70 SERIES 18/04/2018

8. Installation menu

Image 8-52

When the CLO is activated, this will be indicated in the status menu in both LCD and OSD.

CLO

Image 8-54

Image 8-53

8.8 Display Setup

About

Described in other topics, related to projector version.

601–426 F70 SERIES 18/04/2018

8. Installation menu

92 601–426 F70 SERIES 18/04/2018

9. System settings menu

9. SYSTEM SETTINGS MENU

Overview

• Communication

• Apply a menu theme

• Standby E CO

• Service

•Reset

• Lens F eatures

• Controlling the backlight of the LCD Display

9.1 Communication

About

System settings / Communication

Network connection is required to communicate with the projector via LAN or Internet.

Current Ethernet comm unication information is given, and can be edited in this menu.

Default mode for Ethernet communications are: Automatic ON / IP Version 4 DHCP mode.

Setting Description

Automatic

ON DHCP enabled

OFF Static

IP version 4

Static mode Set address, subnet mask and default gateway according to network speciﬁcation.

DHCP mode

Assigned IP address, subnet mask and gateway.

Image 9-1

Manually set up the IP adress

Go to the menuS ystem settings / Communication / LA N

Enable the Auto zone on the display and press enter. The Auto zone will change to “Manual”.

Scroll down, and modify the desired ﬁelds. When in the desired ﬁelds, press “Enter” to enable the virtual keyboard, enter the desired values, and press “Enter” again to conﬁrm the change.

9.2 Apply a menu theme

About

System se ttings / Themes

601–426 F70 SERIES 18/04/2018

9. System settings menu

Themes are used to apply a predeﬁned functionality to the OSD display. There are two options: light (default) or dark. (From software version 1.5, the “Dark” theme is the default.)

It is the “Light” option that is shown in the menu screenshots in this manual, as this gives a better rendering.

9.3 Standby ECO

About Standby ECO

When the E CO mod e is enabled, the projector will automatically go to ECO standby m ode after a time-out (default 15 minutes). All electronics (including fans, pumps, ...) g o down except for a very s mall wake-up controller. See section dedicated to the Power Mode transitions for further details.

How to enable the ECO mode

1. In the main m enu, select System S ettings →Standby ECO.

Image 9-2 System Settings Menu — Standby ECO

2. To enable the ECO mode, make sure the slider is set to On. The slider is enabled when set to the right and when it is colored

blue.

How to disable the ECO mode

1. In the main m enu, select System S ettings →Standby ECO.

Image 9-3

2. To disable the EC O mode, make sure the slider is set to Off. The slider is disabled when set to the left and when it becomes grey.

9.4 Service

About

System s ettings / Service

The Service Menu is for s ervice personnel and / or advanced users only.

See the Service Manu al for detailed informatio

The menu is password protected.

n regarding service issues.

9.5 Reset

What can be done?

All settings and values on the projecto all settings together (factory reset).

Default settings

The following settings are default settings:

r can be reset to its default values. This can be done for one or more s ettings separately, or

601–426 F70 SERIES 18/04/2018

Setting Default value

UserInterface

Network

System Eco Mode (if applicable)

Screen S creen luminance - Unit nits

Optics High Contrast Off

Theme Light

Communication

LAN, Automatic settings

Available

9. System settings menu

Illumination Power

ImageConnector Color Space

Signal Range

ImageResolution

ImageWarp

ImageBlend

ImageRealColor

ImageStereo Sync delay

ImageDisplay Display mode

ImageOrientation Orientation

ImageSource Source ﬁles Standard

ImageFeatures

Output Resolution (if applicable)

Screen size 5120x3200 / 2560x1600

4 corner

Bow

Warp ﬁles Disabled, no ﬁles selected

Blend/Mask size

Black Level

Black Level Files

Blend Files

P7 Realc olor all set to native

Swap eye Off

Dark time lowest value a va ilab le

Contrast

Brightness mid value

Saturation

100%

auto

4K UHD

Warp off, no warp

disabled, all value to zero

Disabled, no ﬁles selected

0µs

AutoStereo

Table, Front

mid value

Sharpness

Gamma

Cropping (if applicable) Off

Aspect Ratio (if applicable)

How to reset all projector settings

1. In the main menu, s elect System Settings → Res et.

2. In the Reset menu, select RESET ALL and click OK.

How to reset one or more p rojector settings

1. In the main menu, s elect System Settings → Res et.

Image 9-4 System Settings menu, Reset

mid value

16:9

601–426 F70 SERIES 18/04/2018 95

9. System settings menu

The Reset menu is displayed.

Image 9-5 Reset menu

2. N avigate to the checkbox next to the settings that need to be reset and press OK.

Multiple se lections are possible.

3. S elect RESET and pr ess OK to res e t all selected settings.

9.6 Lens Features

About

In order to prevent unintentional lens adjustments, especially after e.g. a completed setup and adjustment, there is a pos sibility to disable certain lens adjustment functions. These functions are directly accessible via the rem ote control, and can by that easily be adjusted by accident.

Enter the menu shown below, and disable the desired functions by toggling the desired buttons. The m enu below shows all lens options in enabled position.

Image 9-6

9.7 Controlling the backlight of the LCD Display

What lighting can be controlled?

You can choose how quickly the backlight of the LCD turns off. You can select one of the default values, or enter a custom value.

Alternatively, you can turn on Stea lth Mode instead. By activating this mode, both the backlight of the LCD as well as the backlight of all the buttons of the keypad will be permanently disabled.

How to control

1. In the main menu, System S ettings → Backlight.

601–426 F70 SERIES 18/04/2018

Barco F70-4K8 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual