Barco DP2K-10SLP, DP2K-8SLP User And Installation Manual

Download

Page 1

DP2K SLP Series

R5906847/00 02/06/2017

User and Installation manual

Page 2

Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium Phone: +32 56.36.82.11 Fax: +32 56.36.883.86 Support: www.barco.com/en/support Visit us at the web: www.barco.com

Printed in Belgium

Page 3

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or m erchantability and ﬁtness f or a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be dow nloaded from the Barco web site w

ttps://www.barco.com /en/signin.

ww.barco.com or from the secured Barco web site

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

EMC statements

EN55032/CISPR32 Class A MME (MultiMedia Equipment)

Warning : This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interfer-

ence.

Class A ITE (Information Technology Equipment)

Warning : This is a class A product. In a dom estic environment this product may cause radio interference in which case the user may be

required to take adequate measures.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may c ause harmful interference to radio communications. Oper ation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense

Changes or modiﬁcations not expressly approved by the party responsible for c ompliance could void the user’s authority to operate the equipment

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must im mediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.

The pe riod of gu a rantee begins on the date of transfer of risks, in the case of special systems and software on the date of comm issioning, at latest 30 days after the transfer of risks. In the event of justiﬁed notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase pr ice or cancellation of the contract. All other claims, in particular th ose relating to compensation for direct or indirect damage, and also da mage attributed to the operation of software as well as to other services provided by Barc o, being a component of the system or independent se rvice, will b e deemed invalid provided the damage is not proven to be attributed to the absenc e of pr operties guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modiﬁcations or repairs o n goods delivered by Barco, or if the goods ar e ha ndled inc orrectly, in particular if the systems are operated incorrectly or if, after the transfer o f risks, the goods are subject to inﬂuences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee co verage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well a s normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations speciﬁed in this manual must be complied with by the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as commen ts or examples and are not to be understood as advertising for the products or their manufac

turers.

Page 4

Page 5

Table of contents

TABLE OF CONTENTS

1. Safety................................................................................................................. 3

1.1 General considerations............................................................................................................... 4

1.2 Important safety instructions ......................................................................................................... 6

1.3 Product s afety labels ................................................................................................................. 9

1.4 High Brightness precautions: Hazard Distance (HD) .............................................................................. 10

1.5 HD for fully enclosed projection systems ...........................................................................................12

1.6 HD in function of modifying optics .................................................................................................. 13

2. Getting started.... ................ .................. ................ ................ ................ ............... 15

2.1 Installation requirements . . . ......................................................................................................... 16

2.2 Unpacking the projector ............................................................................................................. 18

2.3 Initial inspection......................................................................................................................20

2.4 Communicator PC version ..........................................................................................................21

2.5 Commander & Web Comm ander . .................................................................................................. 22

3. Installation process ...............................................................................................23

3.1 Installation process overview........................................................................................................24

3.2 Software upgrade . . . ................................................................................................................. 25

3.3 Starting up and adjusting the system ...............................................................................................26

4. Physical installation ..............................................................................................27

4.1 Positioning the DP2K SLP-series projector at port window ........................................................................ 28

4.2 Connecting the projector with the power net ....................................................................................... 31

5. Lenses & Lens selection.........................................................................................33

5.1 Available lenses ..................................................................................................................... 34

5.2 Lens selection .......................................................................................................................35

5.3 Lens installation .....................................................................................................................36

5.4 Lens removal ........................................................................................................................37

5.5 Lens shift, zoom & focus . . . ......................................................................................................... 38

6. Input & Communication ..........................................................................................41

6.1 Introduction ..........................................................................................................................42

6.2 LocalKeypad ........................................................................................................................ 43

6.3 Projector Status...................................................................................................................... 45

6.4 Integrated Cinema Processor (ICP) ................................................................................................ 46

6.5 HD-SDI I nput Module (optional). . . .................................................................................................. 47

6.6 Integrated Media Block/Server (optional) . . . ........................................................................................ 50

6.7 Cinema Controller ...................................................................................................................51

7. ICMP ........ ................ ................ ................ ................ ................ ................ .........53

7.1 ICMP introduction. . ..................................................................................................................54

7.2 ICMP HDD...........................................................................................................................56

7.3 ICMP communication ports ......................................................................................................... 57

7.4 ICMP source input ports............................................................................................................. 59

7.5 ICMP DisplayPort speciﬁcations.................................................................................................... 60

7.6 ICMP S DI speciﬁcations.............................................................................................................62

7.7 ICMP HDM I 2.0 speciﬁcations ...................................................................................................... 66

7.8 ICMP HDM I 1.4 speciﬁcations ...................................................................................................... 69

7.9 ICMP status LEDs ................................................................................................................... 71

7.10 ICMP HDD status LEDs............................................................................................................. 72

7.11 ICMP device certiﬁcate..............................................................................................................74

7.12 ICMP conﬁgurationvia Communicator ............................................................................................. 76

7.13 ICMP reset........................................................................................................................... 77

7.14 Obtaining the Barco ICMP certiﬁcate............................................................................................... 78

7.15 Removing a HDD from theICMP ................................................................................................... 79

7.16 Installing a HDD intothe ICMP......................................................................................................80

8. Communicator Touch Panel.. .................. ................ ................ ................ ................ .83

8.1 Communicator Touch Panel .........................................................................................................84

8.2 Installing the Touch Panel interface................................................................................................. 86

8.3 Repositioning the Touch Panel interface . . . ........................................................................................ 88

9. Starting up..........................................................................................................89

9.1 Switching the DP2K SLP-series ON ................................................................................................90

9.2 Switching the DP2K SLP-series OFF............................................................................................... 91

10. Scheimpﬂug........................................................................................................93

10.1 Scheimpﬂug introduction . . . ......................................................................................................... 94

10.2 Scheimpﬂugadjustment............................................................................................................. 96

10.3 Fixation of the Lens Holder front plate .............................................................................................. 98

10.4 Back Focal Leng th adjustment .....................................................................................................100

R5906847 DP2K SLP SERIES 02/06/2017

Page 6

Table of contents

11. Convergence ............ ................ ................ ................ ................ .................. ....... 105

11.1 Convergence controls ..............................................................................................................106

11.2 Preparing for convergence adjustment . . . . . .......................................................................................108

11.3 Converging the blue pattern onto the red pattern .................................................................................109

11.4 Converging the green pattern onto the red pattern................................................................................110

11.5 Closing off the Light Processor compartment . . . .................................................................................. 111

12. Color calibration.................... ................ ................ .................. ................ ........... 113

12.1 Calibration process .................................................................................................................114

12.2 Color gamut calibration .............................................................................................................115

13. Preventative maintenance actions ............ ................ ................ ................ ............... 117

13.1 1 month maintenance actions ......................................................................................................118

13.2 3 month maintenance actions ......................................................................................................119

14. Maintenance procedures............ .................. ................ ................ ................ ......... 121

14.1 Check the large dust ﬁlter ..........................................................................................................122

14.2 Check the small dust ﬁlter..........................................................................................................124

14.3 Vacuum cleaning of the dust ﬁlters ................................................................................................126

14.4 Washing and drying the dust ﬁlters ................................................................................................127

14.5 Cleaning the lens .. . ................................................................................................................128

14.6 Cleaning the exterior of the projector ..............................................................................................129

14.7 Authorization to clear security warning on the projector ..........................................................................130

15. Removal and installation of the projector covers .. ................ ................ ................ ....... 131

15.1 Removal of the Light Source cover ................................................................................................132

15.2 Removal of the rear cover..........................................................................................................133

15.3 Removal of the top cover...........................................................................................................134

15.4 Removal of the left side cover......................................................................................................135

15.5 Removal of the top cover plate of the Light Processor compartment.............................................................136

15.6 Removal of the side cover plate of the Light Processor compartment ...........................................................138

15.7 Installation of the side cover plate of the Light Processor compartment .........................................................139

15.8 Installation of the top cover plate of the Light Processor compartment...........................................................140

15.9 Installation of the left side cover ...................................................................................................141

15.10 Installation of the top cover.........................................................................................................142

15.11 Installationof the rear cover........................................................................................................143

15.12 Installation of the Light Source cover ..............................................................................................144

A. Speciﬁcations .. ................ ................ ................ ................ ................ ................ ... 145

A.1 Speciﬁcations of theDP2K-8SLP series...........................................................................................146

A.2 Speciﬁcations of theDP2K-10SLP series .........................................................................................147

A.3 Dimensions of the DP2K SLP-series projector ....................................................................................148

A.4 Dimensions of the universalpedestal............................................................................................. . 149

A.5 Technical Regulations ..............................................................................................................150

B. Pin conﬁgurations ................................................................................................ 151

B.1 About General Purpose Inputs & Outputs (GPIO).................................................................................152

B.2 Pin conﬁgurations of the Cinema Controller communication ports ...............................................................154

B.3 Pin conﬁgurationsof the ICMP communication ports .............................................................................155

C. Environmental information ........ ................ ................ ................ .................. ........... 159

C.1 Disposal information................................................................................................................160

C.2 China RoHS compliance ...........................................................................................................161

C.3 Taiwan RoHS compliance ......................................................................................................... . 163

C.4 Turkey RoHS compliance ......................................................................................................... . 164

C.5 Hazards .............................................................................................................................165

C.6 Production address . ................................................................................................................166

C.7 Contact information.................................................................................................................167

Index....... ................ .................. ................ ................ ................ ................ ........... 169

2 R5906847 DP2K SLP SERIES 02/06/2017

Page 7

1. SAFETY

About this document

Read this document attentively. It contains important information to prevent personal injury while installing and using the DP2K SLP-series projector. Furthermore, it includes several cautions to prevent damage to the DP2K S LP-series projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing the DP2K SLP-series projector.

Clariﬁcation of the term “DP2K SLP-series” used in this document

When referring in this document to the term “DP2K SLP-series” means that the content is applicable for following Barco products:

• DP2K-10SLP, DP2K-8SLP

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. Observing the speciﬁcation mentioned in this chapter is critical for projector performance. Neglecting this can result in loss of warranty.

Overview

• General considerations

• Important safety instructions

• Product safety labels

• High Brightness precautions: Hazard Distance (HD)

• HD for fully enclosed projection systems

• HD in function of modifying optics

1. Safety

R5906847 DP2K SLP SERIES 02/06/2017

Page 8

1. Safety

1.1 General considerations

General safety instructions

• Before operating this equipment please read this manual thoroughly and retain it for future reference.

• Installation and preliminary adjustments should be performed by qualiﬁed Barco personnel or by authorized Barco service dealers.

• All warnings on the projector and in the doc umentation manuals should be adhered to.

• All instructions for oper ating and use of this equipment m ust be followed precisely.

• All local installation codes should be adhered to.

Notice on safety

This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, w hich are the safety standards of information technology equipment including electrical business equipmen t. These s afety standards impose important requirements on the use of safet materials and insulation, in order to protect the user or operator against risk o f electric s hock and energy hazard and having access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against the risk of ﬁre. Simulated single fau safety of the equipment to the user even when the equipment’s norm al operation fails.

lt con dition testing ensures the

Notice on optical radiation

This p rojector embeds extremely high brightness (radiance) lasers; this laser light is processed through the projectors optical path. Native laser light is not acc essible by the end user in any us e case. The light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a signiﬁcant risk for the human eye when exposed direc tly w ithin the beam. This risk is not speciﬁc related to the characteristics of laser light but solely to the high thermal induced energy o f the light source; which is equivalent with lamp based systems.

Thermal retinal eye injury is possible when exposed within the Hazard Distance (HD). The HD is deﬁ ned from the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as described in the chapter “Hazard Distance”.

y critical components,

WARNING: No direct exposure to the beam within the ha zard distance shall be permitted, RG3 IEC 62471-

5:2015

CAUTION: Use of controls or adjustments or performance of procedures other than those speciﬁed he rein

may result in hazardous radiation exposure.

Restricted access location

This product may only be installed in a r estricted access location. The deﬁnition of a “restricted access location" is a location for equipment where both of following applies:

• Access can only be gained by SERVICE PERSO NN EL or by OPERATORS who have been instructed about the reasons for the restriction applied to the location and about the precautions that shall be taken.

• Access is through the use of the tool or lock and key, or other means of security, and is controlled by the authority responsible for the location.

Why a restricted acc ess location: This is a RG3 product. Based on international requirements, no person in allowed to enter the projected beam within the z one between the projection lens and the r elated Hazard Distance (HD). This shall be physically impossible by creating sufﬁcient separation height or by placing optional bar riers. Within the res tricted area operator training is considered sufﬁcient. The applicable separation heights ar e discussed in "High Brightness precautions: Hazard Distance (HD)", page 10.

Users deﬁnition

Throughout this manual, the terms S technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and E LECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimiz any person other than SERVIC E PERSONNEL or TRAINED PROJECTIONISTS, AUTHORIZED to operate professional projection systems.

The TRAINED PRO JE CT IONISTS may only perform the maintenance task d escribed in the User & Installation manual. All other maintenance tasks and service tasks must b e performed by qualiﬁed SE RVICE PERS O N NEL.

The DLP Cinema Systems are intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PE RSONNE L familiar with potential hazards associated with high voltage, high intensity light beams generated by lasers. Only qualiﬁed SERVICE PERS ONNE L and TRAINED PROJECTIONISTS, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure.

ERVICE PERSONNEL and T RA INED PROJECTIONIST refers to persons ha ving appropriate

e the potential risk to themselves or other persons. The term U SER and OPERATOR refers to

R5906847 DP2K SLP SERIES 02/06/2017

Page 9

1. Safety

Owner’s record

The part number and serial number are printed on a label which is stuck on the respective part. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Barco dealer regarding this product.

Product article number

Product serial number

Dealer

R5906847 DP2K SLP SERIES 02/06/2017 5

Page 10

1. Safety

1.2 Important safety instructions

To prevent the risk of electrical shock

• This projector s hould be operated from an A C power source. Ensure that the mains voltage and capacity matches the projector electrical ratings. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the grounding.

• Installation according to the local electrical code and regulations by qualiﬁed technical personnel only.

• This pr oduct is equipped with a three-terminal barrier strip for the connection of a mono phase power line with a separate earth ground PE. If you are unable to install the AC Requirements, contact your electrician. Do not defeat the purpose of the grounding.

• The cross-sectional area of the conductors in the power supply cord shall be not less than 2.5 mm V. Take into account that the cable gland of the projector allows a cable diameter from 8 to 13 millimeter.

• A readily accessible disconnect device must be incorporated externally to the equipment for removal of the power to the projector mains terminals.

• Warning: High leakage c urrent. Earth connection essential b efore connecting supply.

• Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cor d.

• Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it has been exam ined and approved for operation by a qualiﬁed service technician.

• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat.

• Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage po ints or short circuit parts that could result in a risk of ﬁre or electrical shock.

• Do not expose this projector to rain or moisture.

• Do not immerse or expose this projector in water or other liquids.

• Do not spill liquid of any kind on this pr ojector.

• Should any liquid or solid object fall into the c abinet, unplug the set and have it checked by qualiﬁed service personnel before resuming operations.

• Do not disassemble this projector, always take it to a trained service person when service or repair work is required.

• Do not use an accessory attachment which is not recommended by the manufacturer.

• Lightning - For added protection for this video product during a lightning storm, or whe long periods of time, remove all powe r from the projector. This will prevent damage to the projector due to lightning and AC power-line surges.

n it is left unattended and unused for

(12 AWG), minimum 300

R5906847 DP2K SLP SERIES 02/06/2017

Page 11

1. Safety

To prevent personal injury

• To prevent injury and physical damage, always read this m anual and all labels on the system before powering the p rojector or adjusting the projector.

• Do not underestimate the weight of the projector. The projector weighs ±73 kg ( ±161 lbs). To prevent personal injury a hoisting tool should be used to lift the projector.

• To prevent injury, ens ure that the lens, cooling system and all cover plates are correctly installed. See installation procedures.

• Warning: high intensity light beam. NEV ER look into the lens ! H igh luminance could result in damage to the eye.

• Warning: extremely high brightness projector: This projector embeds extremely high brightness (radiance) lasers; this las er light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been defused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a signiﬁcant risk for the human eye when exposed directly within the beam. This risk is not speciﬁc related to the c haracteristics of laser light but solely to the high thermal induced energy of the light source; which is equivalent with lamp based systems. Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is deﬁned from the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible exposure as des cribed in the chapter "High Brightness precautions: Haza rd Distance (HD)", page 10.

• Based on international requirements, no person in allowed to enter the projected beam within the z lens and the related Hazard Distance (HD). This sh all be physically impossible by creating sufﬁcient separation height or by placing optional barriers. Within the restricted area operator training is considered sufﬁcient. The applicable separation heights are discussed in "High Brightness precautions: Hazard Distance (HD)", page 10.

• The projector shall be installed in a restricted access room equipped with a key or security lock preventing untrained persons entering the Risk Group 3 use zone.

• Switch off the projector before attempting to remove any of the projector’s covers.

• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user.

• Lenses, shields or screens shall be changed if they have become visibly d impaired. For example by cracks or deep scratches.

• The associated S afety responsible of the unit must evaluate the setup before the unit may be started.

• Never point or allow light to be directed on people or reﬂective objects within the HD zone.

• All operators s hall have received adequate training and be aware of the potential hazards.

• Strictly minimize the number of people who have access to the unit. The unit may never be opera ted without permission of the responsible for safety.

• Do not put your hand or an y body part in front of the beam. Do not clean the port window when the projector is switched on.

amaged to such an extent that their effectiveness is

one between the projection

To prevent ﬁre hazard

• Do not place ﬂammable or com bustible m aterials near the projector!

• Barco large screen pr ojection products are designed and manufactured to meet the most stringent safety regu lations. This projector radiates heat on its external surfaces and from v e safe. E xpo sing ﬂammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a ﬁre. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the pro jector whereby no ﬂammable or combust than 40 cm (16”) for this projector. The exclusion zone on the lens side must be at least 5 m. Do not c over the projector or the lens with any material while the projector is in operation. Keep ﬂammable and combustible materials away from the projector at all times. Mount the projector in a well ventilated a the projector to rain or moisture. In the event of ﬁre, use sand, CO electrical ﬁre. Always have service performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco re

• Ensure n o misalignment can occur. Prolonged exposure of wooden walls at close distance (< 20 cm) c an represent a ﬁre risk. After alignment the projector shall be securely mounted to the pedestal.

• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close to walls, or other similar surface. This projector s hould never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from projector and cooling system to the outside of the building.

• Let the projector cool completely befo

re storing. Remove cord from the projector when storing.

rea away from s ources of ignition and out of dire ct sun light. Never expose

placement parts as they may degrade the safety of this projector.

ntilation ducts during normal operation, which is both normal and

ible materials are present. The exclusion zone mu st be not less

or dry powder ﬁre extinguishers. Never use water on an

To prevent battery explosion

• Danger of explosion if battery is incorrectly installed.

• Replace only with the same or equivalent type recommended by the manufacturer.

• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste dispos al rules and regulations to ensure proper disposal.

R5906847 DP2K SLP SERIES 02/06/2017

Page 12

1. Safety

To prevent projector damage

• The air ﬁlters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area would be m onthlyminimum. Neglecting this could result in disr upting the air ﬂow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation.

• The projector m ust always be installed in a manner which ensures free ﬂow of air into its air inlets.

• If more than one projector is installed in a common projection booth, the exhaust air ﬂow requirements are valid for EACH individual projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector as a whole as well as c ausing premature failure of the lasers.

• In or der to ensure that correct airﬂow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC) and safety requirements, it should always be operated with all of it’s covers in place.

• Slots and openings in the cabinet are provided for ventilation. To ensure reliable op e ration of the product and to pro tect it f rom overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Ensure that nothing can be spilled on, or dropped inside the projector. I f this does happen, switch off and remove all power from the projector. Do not operate the projector again until it has been checked by qualiﬁed service personnel.

• Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be nearer to the projector than 10 cm (4") on any side.

• Proper operation of the projector can only be guaranteed in table mounting. It is not permitted to use the projector in another position. See installation procedure for correct installation.

• Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power laser equipment. D irect or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices which case there is a loss of warranty.

• Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror Devices case there is a loss of warranty.

• Save the original shipping carton and packing material. They will c ome in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.

• Remove all p o wer from the projectors mains terminals before c leaning. Do not use liquid cleaners or aerosol c leaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine or abrasive cleaners, s ince these will damage the cabinet. S tubborn stains may be removed with a cloth lightly dampened with mild detergent solution.

• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an an ti-reﬂective coating, therefore, avoid touching the lens. To remove dust o n the lens, use a soft dry cloth. For lens cleaning follow the instructions precisely as stipulated in the projector manual.

• Rated maximum ambient temperature, t

• Rated humidity = 5% to 85% RH Non-condensed.

• An external frame must be used to stack projectors.

= 35°C (95°F).

in which

On servicing

• Do not attempt to service this product yourself, as openi and risk of electric shock.

• Refer all servicing to qualiﬁed s ervice personnel.

• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can lead to permanent damage to the projector and cancellation of the warranty.

• Remove all po wer from the projector a nd refer servicing to qualiﬁed service technicians under the following conditions:

- W hen the power cord or plug is damaged or frayed.

- If liquid has been spilled into the equipment.

- If the product has been exposed to rain or water.

- If t he product does not operate normally when the operating instructions ar e followed. Adjust only those controls that are

covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive w ork by a qualiﬁed technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has be

- If the product exhibits a distinct change in performance, indicating a need for service.

• Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, ﬁre, electric shock or other hazards. Unauthorized substitutions may void warranty.

• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

ng or removing covers may expose you to dangerous voltage p otentials

en damaged.

R5906847 DP2K SLP SERIES 02/06/2017

Page 13

1.3 Product safety labels

Light beam related safety labels

Label image Label description Label location

Hazard RG3: not for hous ehold use symbol

Hot Surface Hazard

Hazard RG3: optical rad iation warning symbol

1. Safety

WARNING! D O NOT LOOK INTO THE LIGHT BEAM NO DIRECT EYE EXPOSURE TO THE BEAM IS PERMITTED. RG3 IEC EN 62471–5:2015. CLA HAZARD DISTANCE: CONSULT S AFETY MANUA L.

COMPLIES W ITH 21 CFR 1040 EXCEP T WITH RE SP ECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER xxxxxx DATED xx xx, xxxx RISK GROUP 3 L IP IEC 62471:2006.

警告！勿观看光束眼睛勿直接接触可允许暴露的光束 (RG3 IEC EN 62471-5:2015 CLASS 1 IEC EN 60825-1:2014) 危害距离：请参考安全手册

DANGER ! NE PAS REG AR DER LE FAISCEAU EVITER TO UTE E XP O SITION DIREC TE DES YEUX AU FAISCEAU. RG3 IEC EN 62471-5:2015. CLASS 1 IEC EN 60825-1:2014. DISTAN CE DE SECURITE : CONSULTER LE MANUEL DE SECURITE.

SS 1 IEC EN 6 0825–1:2014.

R5906847 DP2K SLP SERIES 02/06/2017 9

Page 14

1. Safety

1.4 High Brightness precautions: Hazard Distance (HD)

Hazard Distance (HD) is the distance mea sured from the pr ojection lens at wh ich the intensity or the energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the light source is less than the HD.

Restriction Zone (RZ) based on the HD

The HD depends on the am ount of lumens produced by the projector and the type of lens installed. See next chapter"HD in function of modifying optics", page 13.

To protect untrained end users (as cinema visitors) the installation shall comply with the following installation requirements: Operators shall control ac cess to the beam within the hazard distance or install the product at the height that will prevent spectators’ eyes from being in the hazard distance. Radiation levels in excess of the limits will not be permitted at any point less than 2.0 m eter (SH) above any surface upon which persons other than operators, performers, or employees are permitted to stand or less than 1.0 meter (SH) lateral separation from any place wher e such persons are permitted to be. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 m eter to prevent potential exposure, for example by an individual sitting on another individual’s shoulders, within the HD.

These values are minimum va lues and are based on the guidance provided in IEC 62471-5:2015 section 6.6.5.

The end user must understand the risk and apply protective meas ures based upon the hazard distance as indicated on the label and in the user information. Installation m ethod, barriers, detection system or other applicable control measure shall prevent hazardous eye access to the radiation within the hazard distance.

For example, projectors that have a HD greater than 1 m and emit light should be positioned in accordance with “the ﬁxed projector installation” param eters, resulting in a HD that does not extend into the audience area unless the beam is at least 2.0 meter above the ﬂoor level. In non-cinema environments where unrestrained behavior is reasonably foreseeable, the minimum separation exposure, for example by an individual sitting on another individual’s shoulders, within the HD. For example, a sufﬁciently large separation height may be achieved by mounting the im age projector on the ceiling or through the use of physical barriers.

For applications installed in the USA market the a bove limits do not apply. The relevant minimum separation height is 2.5 meter (8.2 ft) and the separation width is deﬁned as 1.0 meter (3.3 ft) by the FDA CDRH.

height should be greater than or equal to 3.0 m eter to prevent potential

into an uncontrolled area where persons may be p resent

RA TH

Image 1-1 ASideview. B Top view. RA Restricted Access location (boot area of projector). PR Projector. TH Th eater. RZ Restriction Zone in the theater. SH Separation Height. SW Separation Width.

Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the r elated hazard distance (HD). This shall b e physically impossible by creating sufﬁcient separation height or by placing bar riers. The minimum separation height takes into account the surface upon which persons other than operator, performers or employees are permitted to stand.

On image 1-2 a typical s etup is displayed. It m ust be veriﬁed if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This can be done by u sing physical barrier, like a red rope as illustrated in image 1-2.

The restricted area sticker can be replaced by a sticker with only the symbol.

(B) TOP VIEW(A) SIDE VIEW

R5906847 DP2K SLP SERIES 02/06/2017

Page 15

Image 1-2

RESTRICTED

AREA

1. Safety

RESTRICTED

R5906847 DP2K SLP SERIES 02/06/2017 11

Page 16

1. Safety

1.5 HD for fu lly enclosed projection systems

Restriction Zone (RZ) based on the HD

The projector is also suitable for re ar projection applications; projecting a beam onto a defuse coated p rojection sc reen. As displayed in im age 1-3 two areas should be considered: the restricted enclosed p rojection area (RA) and the observation area (TH).

RESTRICTED

RA TH

AREA

RESTRICTED

AREA

HDDIFFUSE

REFLECTION

reﬂection

); also taking into account a 1 meter lateral

Image 1-3 RA Restricted Access location (enclosed projection area). PR Projector. TH Theater (observation area). RZ Restriction Z one. PD Projection Distance. SW Separation W idth. Must be minimum 1 meter.

For this type of setup 3 different HD shall be considered:

• HD as discuss ed in "High Brightness precautions: Hazard Distance (HD)", page 10, relevant for intrabeam exposure.

•HD

reﬂection

•HD

diffuse

: the distance that has to b

: the relevant distance to be considered while obs erving the defuse surface of the rear projection screen.

e kept re strictive related to the reﬂected light from the rear projection screen.

As described in "High Brightness precautions: Ha zard Distance (HD)", page 10, it is mandatory to create a restricted zone within the beam areas closer than any NOHD. In the enclosed projection area the combination of two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to the rear reﬂection from the screen (HD separation.

The HD projection screen. To determine the HD distance for the used lens and projector model see graphs in chapter "HD in function of

distance equals 25% of the difference between the determined HD distance and the p rojection distance to the rear

reﬂection

modifying optics", page 13.

reflection

= 25% (HD – PD)

The light emitted from the screen within the observation shall never exceed the RG2 exposure limit, determined at 10 cm. The HD

can be neglected if the measured light at the screen surface is below 5000 cd/m² or 15000 LUX.

diffuse

R5906847 DP2K SLP SERIES 02/06/2017

Page 17

1.6 HD in function of modifying optics

Hazard Distance

10SLP 8SLP

1,8

1,6

1,4

1,2

0,8

Hazard Distance [m]

0,6

0,4

0,2

1. Safety

Image 1-4

1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6

Throw Ratio

R5906847 DP2K SLP SERIES 02/06/2017 13

Page 18

1. Safety

14 R5906847 DP2K SLP SERIES 02/06/2017

Page 19

2. Getting started

2. GETTING STARTED

About this chapter

Read this chapter before installing your DP2K SLP-series projector. It contains important information con cerning installation requirements for the DP2K SLP-series projector, such as minimum and max imum allowed ambient temperature, h umidity conditions, required safety area around the installed projector, required power net, etc.

Furthermore, care ful consideration of things s uch as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system.

Overview

• Installation requirements

• Unpacking the projector

• Initial inspection

• Communicator PC version

• Commander & Web Commander

R5906847 DP2K SLP SERIES 02/06/2017

Page 20

2. Getting started

2.1 Installation requirements

Environmental conditions

The table below summarizes the physical environment in which the DP2K SLP-series projector may be safely operated or stored.

Environment Operating Non-Operating

Ambient Temperature 10°C (50°F) to 35°C (95°F) -15°C (5°F) to 60°C (140°F)

Air cleanliness Clean ofﬁce environment (equivalent with clean room

Humidity

Altitude

Let the projector acclimatize after unpacking. Neg lecting this may result in a startup failure of the Light Processor Unit.

standard ISO 14644-1 ISO Class 9)

5% to 85% RH Non-condensed 5% to 95% RH Non-Condensed

-60 (-197 Ft) to 3000 m (9843 Ft) -60 (-197 Ft) to 10000 m (32810 Ft)

Use in high altitude conditions

When 3000 m environmental condition is combined with the highest permissible temperature (35°C ambient), the projector may be expected to go into warning status. Hence, for high altitude conditions, we advise ma x 30°C ambient condition (25°C is preferred).

Furthermore, to avoid temperature warnings on laser banks, we advise in high altitude to set c ooler fans to 100%.

n.a.

Main Power requirements

The DP2K SLP-series projec tor operates from a nominal mono phase power net with a separate earth ground PE .

Projector Power requirements

DP2K-10SLP 200-240 VAC, 50-60 Hz, 10 A at 200 VAC

DP2K-8SLP 200-240 VAC, 50-60 Hz, 10 A at 200 VAC

The power cord required to connect t he projector with the power net is not delivered with the projector. It is the responsibility of the customer to provide the correct type of power cord. The cross-sectional area of the conductors in the power supply cord shall not be les s than 2.5 mm

To protect opera ting personnel, the National Electrical Manufacturers A ssociation (NEMA) recommends that the instrument panel and cabinet be grounded. In no event shall this projector be operated without an adequate cabinet ground connection.

The AC supply must be installed by a qualiﬁed electrician in conformance to local codes. Hardware, wire sizes and conduit types must comply with local codes.

A readily accessible disconnect de vice shall be incorporated externally to the equipment for removal of the power to the equipment mains terminals.

(12 AWG), minimum 300 V. Take into account that the cable gland allows a cable diameter from 8 to 13 mm.

WARNING: Disconnect the power to the unit mains terminals for removal of all power from the unit.

The DP2K SLP-series projector does not have a built in UPS unit.

Projector weight

Do not underestimate the weight of the DP2 Ensure that the pedestal on which the projector is installed is capable of supporting the complete load of the sy stem. M inimum 4 adult persons are needed to carry the projector.

Barco offers a pedestal for the DP2K S LP-series projector. This universal pedestal allows for a solid and easy set up of the projector. The un iversal pedestal support 19” rack systems. (projector peripherals such as alternative content switchers, ShowVault, etc.)

16 R5906847 DP2K SLP SERIES 02/06/2017

K SLP-series projector. The projector weight approximately 73 kg (161 lb.) without lens.

Page 21

CAUTION: An external frame must be used to stack projectors.

2. Getting started

R5906847 DP2K SLP SERIES 02/06/2017 17

Page 22

2. Getting started

2.2 Unpacking the projector

What you need to do?

Upon delivery, your projector is packed into a carton box upon a wooden/plastic pallet and secured with banding and fastening clips. Furthermore, to provide protection during transportation, the projector is surrounded by foam. Once the projector has arrived at the installation site, it need s to be rem oved from its carton box and wooden/plastic pallet in a safe manner without dam aging the projector.

How to unpack your projector?

1. L oosen the banding (reference 1 image 2-1) by pulling the free end of the banding loop in the clip.

Image 2-1

2. L ift up the carton box (reference 2 image 2-2) as a whole an

3. Take out the small box (reference 3 image 2-2) between the polystyrene foam on top of the projector. This box contains the

product documentation (manuals e tc.).

4. Remove the polystyrene foam (reference 4 image 2-2) from the top of the projector.

d remove it away from the projector package.

Image 2-2

5. O pen the plastic bag and lift the projector out of its packaging, using the handles provided in the projector base.

R5906847 DP2K SLP SERIES 02/06/2017

Page 23

Image 2-3

6. R emov e the protective foam from the Lens Holder open ing.

2. Getting started

R5906847 DP2K SLP SERIES 02/06/2017

Page 24

2. Getting started

2.3 Initial inspection

General

Before shipment, the projector was inspected and found to be free of mechanical and electrical defects. As soon as the projector is unpacked, insp ect for any damage that may have occurred in transit. Save all packing material until the inspection is completed. If damage is found, ﬁle claim with carrier immediately. The Barco Sales and Service ofﬁce should be notiﬁed as soon as possible.

Box content

•Projector.

• User and installation manual (this document).

• Safety manual.

The projector lens is not included in the package of the projector.

Mechanical check

This check shou ld conﬁrm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and scratches, and that the operating panel is not s cratched or cracked. The Barco Sales and Service ofﬁce should be notiﬁed as soon as possible if this is not the case.

Tamper labels

During ins tallation please inspect the tamper labels, if they are damaged please contact Barco tech s upport.

The tamper labels are requ ired by DCI to provide easy visual indication if the equipm ent was tampered with. The projectors are tested and labeled for shipping to ensure that the system was not compromised before reaching the customers ﬁnal destination.

These tamper labels can be found behind the input cover (partial visible), top cover and left side cover (orientation: looking at the screen). See chapter page 131, for instructions on how to remove the projector covers.

Image 2-4 Barco tamper label (required for DCI).

20 R5906847 DP2K SLP SERIES 02/06/2017

Page 25

2. Getting started

2.4 Communicator PC version

Conﬁguration tool

A uniquely powerful and easy to use conﬁgur ation tool for the Barco cinema projector. This Communicator s oftware for PC provides all the necessary tools and only those tool neces sary for the conn ected p rojector to s etup and control this projector. A comprehensive array of easy to access menu pages provide the projectors digital input, output and screen display via a combination of simple buttons and displays.

Image 2-5

Quick and Easy conﬁguration

Clearly indicated tab pages allow the control o f Projector connection, conﬁguration, test, color calibration and conﬁguration with an existing automation system. All ac tions can be activated by a simple click. Depending on the user level, functions are enabled or disabled in the software. The enabled functions are only accessible via a password entry and that prevents misalignment once everything is correctly aligned.

The Com m unicator PC version has its own user gu ide which latest version is available on the Barco website.

R5906847 DP2K SLP SERIES 02/06/2017 21

Page 26

2. Getting started

2.5 Commander & Web Commander

Commander

All Barco Alchemy projectors come with the ‘Barco Commander’ software that runs from a touch panel c ontroller or PC.

Image 2-6

Web Commander

All Barco Alchem y projectors come with the ‘Ba rco Web Commander ’ screen management system featuring an intuitive user interface for simple operation.

The Barco Alchemy projectors have been carefully designed to greatly increase the level of operational efﬁciency. Projectionists can now enjoy a streamlined and intuitive user interface that seamless blends projector control with a full-ﬂedged screen management system. The ‘Barco Web Commander’ user interface is rea It is accessed via a web browser and is als o fully supported on iO S and Android tablets thanks to the free ‘Barco CineMate’ iOS and Android app.

Image 2-7

dily available on the projector without any additional software installation.

The Commander and Web Commander have their own user guide which latest version is available on the Barco website.

22 R5906847 DP2K SLP SERIES 02/06/2017

Page 27

3. Installation process

3. INSTALLATION PROCESS

About this chapter

After you have unpacked and checked the projector, you can start with the installation process of your DP2K SLP-s eries projector. This chapter gives an ov erview of all the different stages in the installation process which you have to be followed to set your DP2K SLP-series projector up and running. Each stage is brieﬂy described and refers to more detailed step by step procedures in this manual.

Use this overview as a checklist to en sure that all stages have been followed in the setup process of the DP2K SLP-series projector.

Let the projector acclim atize to ambient conditions after unpacking. Neglecting this may result in a startup failure of the light processo r unit.

Overview

• Installation process overview

• Software upgrade

• Startingupandadjustingthesystem

R5906847 DP2K SLP SERIES 02/06/2017

Page 28

3. Installation process

3.1 Installation process overview

Installation process Projector

1. C heck if all installation requirements are fulﬁlled such as the environment conditions of the installation area, electrical facili-

ties, etc. Note that a s olid pedestal is required to support the projector. For more info see topic installation requiremen ts.

2. P h ysical installation of the projector upon its pedestal.

3. E lectrical connection with the power net. See "Connecting the projector with the power net", p age 31.

4. In stallation of the lens. First select a lens with appropriate throw ratio covering the screen size and the projector - screen

distance. Then install the lens in the lens holder of the projector. For more information about available lenses, lens selection and lens installation see chapter "Lens installation", page 36.

Caution: The projector is delivered with a plastic cover inside the Lens Holder. Remove the c over prior to installing the lens.

5. In stallation of the ICMP, IMB, IMS or HDSDI input module. (only in case no ICMP, or IMB or IMS or HDSDI is factory installed).

6. Installation of the HDDs. In case the HDDs of the ICMP are delivered separated from the projector remove the protection tape

from the HDD input slots and install all three HDDs as des cribed in the procedure"Installing a HDD into the ICMP", page 80. Make sure that all HDDs in the ICMP HDD set have the s ame storage c apacity. See label on top of the HDD to know the s torage capacity.

7. In stallation of the optional Comm un icator Touch Panel. See chapter "Installing the Touch Panel interface", page 86.

8. Upgrade all software to the latest available version. See "Software upgrade", pa ge 25.

9. S tart up your projector and adjust the system. See "Starting up and adjusting the system", page 26.

R5906847 DP2K SLP SERIES 02/06/2017

Page 29

3. Installation process

3.2 Software upgrade

How to upgrade the software

1. S witch on the projector. The pro jector can now be switched on. P lace the ON/OFF switch of the projector in the ”I” position. A s a

result the projector starts to initialize. The status lights of the projector lights up GREEN once the projector is initialized. In case the status lights up RED may indicate a tamper event during t ransport. If so, contact Barco customer service.

2. Download and install the latest version of Communicator. The program can be downloaded for free from Barco’s website, (URL:

ttp://www.barco.com). Click on myBarco and login to get access to secured information. Registration is neces sary.

If you are not yet registered, click on New to myBarco and follow the ins tructions. With the created login and password, it is possible to login where you can download the software.

3. D ownload the latest ﬁrm ware from Barco’s website in the same way as for Communicator.

4. S tart Communicator and make a connection with the projector. For more information, consult the Communicator user guide.

5. L ogin as service technician and click on tab Maintenance and select Software update.

6. Click on Launch DC update companion.

7. Click Next, accept the license agreement and continue following the wizard.

R5906847 DP2K SLP SERIES 02/06/2017 25

Page 30

3. Installation process

3.3 Starting up and adjusting the system

Adjustment steps

1. S elect the corresponding lens parameters for the installed lens. See us er guide of the Communicator chapter Installation >

Advanced > Lens parameters.

2. A lignment of the projected image on the screen. The image can be aligned with the screen size of the application. Follow

the next steps to achieve that:

a) Press the STANDBY button on the Local Keypad to activate the light source.

b) Press the DOWSER button on the Local Keypad to open the electronic dowser of the projector. The electronic dow ser is open

if the color of the DO W S ER button is GREEN.

c) Press the TEST PATTERN button on the Local Keypad to project one of the internal test patterns of the projector on the

screen.

d) Performa“Lens Homing”. See user guide of the Communicator.

e) Use the lens ZOOM, SHIFT and FOCUS buttons on the Local Keypad to match the projected image with the screen. Tilt the

projector in case you can not SHIFT the image completely upon the screen. See "Positioning the DP2K SLP -ser at port window", page 28. See chapter "Local Keypad", page 43, for detailed description of the Local Keypad buttons.

3. Adjusting the light path. Normally the lens holder and the convergence of the projector are perfectly adjusted at the factory.

Nevertheless, s ome applications require a readjustment of the lens holder, convergence or both. See procedure "Scheimpﬂug", page 93, and "Convergence", page 105.

4. Creating screen ﬁles, lens ﬁles, and macro ﬁles for FLAT and for SCOPE. See user guide of the Communicator.

5. P erform Co lor calibration. See chapter "Color calibration", page 113.

6. C reate light sensor calibration (LSC) ﬁles. See user guide of the Communicator

7. B acku p of all projector conﬁguration ﬁles. See user g uide of the Communicator.

8. Registration of the projector. The DP2K SLP-series projector is DCI compliant and should be registered.

9. P rojection of a digital cinema movie.

In ca se the projector is equipped with an ICMP, download the ICMP device certiﬁcate, request KDM and DCP from your content supplier, ingest KDM and DCP, and play out the m ovie. for detailed instructions see chapter "ICMP", page 53, and user guide of the Communicator and/or (Web) Commander. In case the projector is equipped with a HD- SDI input module app ly a single or dual channel SM PTE (HD-SDI) source to the input ports of the HD-SDI input module and start up the projector. See chapter "Starting up", page 89. Use the Communicator (Touch Panel) to conﬁgure the applied source. S ee the user guide of the Communicator (Touch Panel) for more detailed information. In case the projector is equipped with an Integrated Media Block (IMB) or Integrated Media Server (IMS) see user guide of the IMB or IMS for detailed instructions.

ies projector

R5906847 DP2K SLP SERIES 02/06/2017

Page 31

4. PHYSICAL INSTALLATION

About this chapter

This chapter describes how the mechanical and electrical set up of your DP2K SLP-series projector has to be done.

Overview

• Positioning the DP2K SLP-series projector at port window

• Connecting the projector with the power net

4. Physical installation

R5906847 DP2K SLP SERIES 02/06/2017

Page 32

4. Physical installation

4.1 Positioning the DP2K SLP-series projector at port window

WARNING: The installation of the DP2K SLP-series requires at least 4 adult p erson s.

General guidelines

• Use a so lid pedestal to mount the DP2K SLP-series projector on t o. Ensure that the pedestal can suppor projector and that all feet of the projector are captured.

• The pedestal s hould be placed in front of the port window wall in a manner such that the projector lens is at a minimum distance of 20 centimeters from the port window.

20 cm

Image 4-1 Positioning at port window

t the weight of the

Necessary tools

• open end wrench 14 mm

• open end wrench 17 mm

Projector centering

1. If the projector is standalone in front of the port window, center the projector with the theatre screen (see reference A image 4-2).

2. If an analog ﬁlm projector is already present (projector will be off-center), try to optimize aim (see reference B image 4-2).

Note: Unlike analog ﬁlm projectors, it is best to kee

is signiﬁcantly above the screen center.

Caution: The front foot has an adjustment range of maximum 70mm. The back feet maximum 150mm.

p the projector lens surface as parallel as possible to the screen, even if it

R5906847 DP2K SLP SERIES 02/06/2017

Page 33

4. Physical installation

The off-center position slightly increases side keystone, but will m inimize horizontal lens offset required.

A B

Image 4-2

3. P roceed to level the pr ojector by adjusting the feet of the projector as follows:

- Loo sen the nut (reference 1 image 4-3) on the threaded rod of the three projector feet. Use a 17 mm open wrench.

- A djust the height of the 3 legs to level the projector. Use a 1 image 4-3).

- S ecure the leg height by tightening the nuts (reference 1 image 4-3) of eac h projector foot.

SCREEN CENTER SCREEN CENTER

OFF-CENTER

4 mm wrench to adjust the he ight as illustrated (reference 2

Image 4-3

4. L ater, when the projector is up-and-running, adjust precise im age geome try and placement.

Projector tilting

In an ideal installation, the DP2K SLP-series lens surface is centered with and parallel to the screen. This orientation helps to ensure optimized lens performance with minimal offset. If this position is not possible (such as when the projector is signiﬁcantly higher than the center of the s creen), it is better to rely on offset rather than extra tilt. In othe r words, use the SHIFT functionality of the Lens Holder pr ior t o tilt the projector.

1. B efore adjusting tilt, ma ke

2. Check the degree of s creen tilt, or measure this incline with a protractor at the screen.

3. Tilt the projector to closely m atch this sc reen tilt angle as follows:

- Loo sen the nut (reference 1 image 4-3) on the threaded rod of the three projector feet. Use a 17 mm open wrench.

- A djust the height of the 3 legs un open wrench to adjust the height as illustrated (reference 2 image 4-3).

- S ecure the leg height by tightening the nuts (reference 1 image 4-3) of eac h projector foot.

sure the projector is as well-centered with the theatre sc reen as possible for the installation area.

til the projected im age matches the projection port window and the screen tilt. Use a 14 mm

R5906847 DP2K SLP SERIES 02/06/2017

Page 34

4. Physical installation

Image 4-4

CAUTION: T he DP2K SLP-series may tilt maximum 20° forward and maximum 5° backwards. No tilt is allowed

sideways.

90°

Inclined screen

The back feet of the projector can be turned out maximum 150 mm. This correspond with a forward tilt of 7° if the front foot is completely turned in.

Barco offers a pedestal for the DP2K SLP -series projector. This universal pedestal allows you t o easily tilt the projectorforwardupto6°.

Use the tilt of the projector feet and the pedestal to get sufﬁcient tilt.

30 R5906847 DP2K SLP SERIES 02/06/2017

Page 35

4. Physical installation

4.2 Connecting the projector with the power net

WARNING: T he total electrical installation should be protected by an appropriate rated and readily accessi-

ble disconnect switch, circuit breakers and ground fault current interrupters. The installation shall be done according to the local electrical installation codes.

CAUTION: ALL PO WER CONNECTIONS to the DP2K SL P-series are made to the 3-slot terminal block located

in a sealed compartment behind the rear cover o f the projector.

CAUTION: The cross-sectional area of the conductors in the Power Supply Cord shall be not less than 2.5

(12 AWG).

Necessary tools

• Medium size ﬂat screw driver (4 mm x 100 mm)

• Torque ﬂat screw driver (medium s ize)

• Large size ﬂat screw driver (8 mm x 150 mm)

• Open end wrench 24 mm

Necessary parts

Certiﬁed AC power supply cord 2.5 mm2(12 AWG), min. 300 V. Take into account that the cable gland of the projector allows a

cable diameter from 8 to 13 mm.

How to connect the main AC power with the DP2K SLP-series projector?

1. R emov e the rear cover of the projector. See procedure "Removal of the rear cover", page 133.

2. Remove the cov er of the main AC compartment by releasing the two captive thumb screws (reference 1 ) .

Image 4-5

3. G uide the AC power supply cord (reference 2 image 4-6) through the cable g land (reference 3 image 4-6) and connect the wires to the 3-terminal strip (reference 6 ima with a torque of 1.7Nm (1.25 lbf*ft).

Warning: Connect ﬁrst the P E wire (reference 4 image 4-6), then the other wires (reference 5 image 4-6).

Tip: Check for good ﬁxation by pulling on each wire.

ge 4-6) as illustrated. U se a torque screw driver to fasten the screws of the 3-terminal strip

R5906847 DP2K SLP SERIES 02/06/2017

Page 36

4. Physical installation

Image 4-6

4. S ecure the AC power supply cord by fastening the cable gland (reference 3 image 4-6). Use a 24m

5. Install the cover of the main AC compartment. Fasten the two captive thumb screws (reference 1 image 4- 7).

m open end wrench

Image 4-7

6. Install the rear cover of the projector. See pr ocedure "Installation of the rear cover", page 143.

R5906847 DP2K SLP SERIES 02/06/2017

Page 37

5. Lenses & Lens selection

5. LENSES & L ENS SELECTION

About this chapter

This chapter gives an overview of available lenses for your D P2K SLP-series and explains how to select the best suited lens for a speciﬁc situation using the lens calculator. Also, it is explained how to install and remove a lens from the projector Lens Holder and how to shift, zoom and focus the lens.

CAUTION: Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Le

before transporting the projector. Neglecting this can damage the Lens Holder and Prism.

CAUTION: Caution when removing or installing the lens! Fragile parts at the inner side of the Lens Holder.

Each time a lens is manipulated (e.g. removed and installed in a p rojector), it needs to be homed and returned.

Overview

• Available lenses

• Lens selection

• Lens installation

• Lens removal

• Lens shift, zoom & focus

R5906847 DP2K SLP SERIES 02/06/2017

Page 38

5. Lenses & Lens selection

5.1 Available lenses

Which lenses are available?

For the DP2K SLP-series the 0.69” DC2K lens family is used.

The table below is su bject to ch anges and was last updated on 15 October 2012. Consult https://my.barco.com for t he most recent information about available lenses for the DP2K SLP-series.

0.69” DC2K zoom lenses

Product Number 2K zoom range Image Motor Block type

R9856520 1.2 - 1.7 image 5-1 M

R98565201 1.2 - 1.7 B

R9856521 1.34 - 1.9 image 5-2 M

R9856522 1.5 - 2.15 image 5-3 M

R9856523 1.7 - 2.55 image 5-4 M

R9856524 2 - 3.9 image 5-5 M

R98565241 2.09 - 3.9 F

Image 5-1

0.69" DC 2K zoom lens 1.2 - 1.7 (R9856520)

Image 5-4

0.69" DC2K zoom lens 1.7 - 2.55 (R9856523)

Image 5-2

0.69" DC 2K zoom lens 1.34 - 1.9 (R9856521)

Image 5-5

0.69" DC2K zoom lens 2 - 3.9 (R9856524)

Image 5-3

0.69" D C2K zoom lens 1.5 - 2.15 (R9856522)

34 R5906847 DP2K SLP SERIES 02/06/2017

Page 39

5. Lenses & Lens selection

5.2 Lens selection

WhichlensdoIneed?

1. G o to Barco’s website on www.barco.com and click on myBarco

2. L ogin on. If yo u are not yet registered create a login a nd password. With the created login and password, it is possible to enter myBarco.

When your login is correct, the start page is displayed.

3. Click the Support tab, then Digital cinema calculator (on the left of the screen) and select the appropriate lens calculator.

The lens calculator (see screenshot, image 5-6) will be displayed.

The lens calculator allows you to have an overview of which lenses are suitable for your speciﬁc pro ject o r setup. Just make your selection of parameters and all possible conﬁgurations are displayed.

Image 5-6 Digital cinema lens calculator

Take into account that w hen the projector is tilted the Screen Width you have to ﬁll in should be larger than the physical screen width due to the keystone distortion of the projected image. How much larger depends ontheamountoftilt.

Due to p roduction tolerances the real distances can differ b y 2% from the calculated values.

For critical situations ( ﬁxed installs that use the lens at one of its extreme zoom positions) this should be taken into account.

R5906847 DP2K SLP SERIES 02/06/2017 35

Page 40

5. Lenses & Lens selection

5.3 Lens installation

How to install a lens into the Lens Holder?

1. Remove the foam rubber in the opening of the Lens Holder if not removed yet.

2. Take the lens assembly out of its packing material and remove the lens caps on both sides.

Caution: Do not touch the glass of the lens!

3. E nsure that the Lens Holder stands in the On-Axis position (horizontal an d vertical mid position).

4. P lace the Lens Holder in the “locked” position by moving the lens lock handle ( reference 1 im age 5 -7) downwards, away from the lens power supply socket (reference 2 image 5-7).

5. G ently insert the lens in such a way that the lens connector matches the socket. To prevent collision of the lens with the critical electronics inside the projector, ensure you centre the lens and keep it on-axis while approaching.

Caution: Do not accidentally bump with the lens against the electronic boards inside the Lens Holder.

Warning: Do not release the Lens yet, as the Lens may fall out of the Lens Holder.

6. Push the lens completely against the Lens Holder front plate. An audible click should be noticed. Onc e seated, there may be no airgap between lens ﬂa nge and Lens Holder front plate.

Caution: Ensure that the lock handle remains in the “locked” position.

Image 5-7

Note: For frequent installation and removal of the lens it is recommended to install the lens while the lock handle is in “open”

position (upwards) and put the lock handle in “ locke installed by trying to pull the lens out of the Lens Holder. (this alternative procedure result in less wear of the Lens Holder)

7. Check if the lens is really secured by trying to pull the lens out of the Lens Holder.

8. A ctivate the corresponding lens parameters for the installed lens. (S ee user guide of the Communicator chapter Installation > Advanced > Lens parameters)

Caution: Not using the correct lens parameters could result in lens damage.

d” position once the lens is inserted. Then check if the lens is properly

Image 5-8

9. P erform a lens H OME & RETURN operation. (See user guide of the Communicator chapter Installation > Advanced > Lens parameters)

Note: The HOME & RETURN operation enables the projector to determine the reference positions of the motorized ZOOM and

FOCUS barrels of the installed lens.

CAUTION: Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens

before transporting the projector. Neglecting this can damage the Lens Holder and Prism.

36 R5906847 DP2K SLP SERIES 02/06/2017

Page 41

5. Lenses & Lens selection

5.4 Lens removal

How to remove a lens from the Lens Holder?

1. S upport the lens with one hand while you unlock the lens holder by sliding the lock handle (reference 1 image 5-9) towards the “unlocked” position as illustrated.

2. G ently pull the lens out of the lens holder, maintaining its coaxial direction.

Caution: Do not accidentally bump with the lens against the electronic boards inside the Lens Holder.

Image 5-9

It’s recommended to place the Lens caps of the original Lens packaging, back on both sides of the removed Lens to protect the optics of the Lens.

It’s recommended to place the foam rubber of the original projector packaging, back into the Lens opening to prevent intrusion of dust. Note that this foam rubber is packed in a plastic bag to prevent the dust, emitted by the foam , from e ntering the projector.

R5906847 DP2K SLP SERIES 02/06/2017 37

Page 42

5. Lenses & Lens selection

SHIFT

ZOOM

5.5 Lens shift, zoom & focus

Motorized lens adjustment

The DP2K SLP-series is equipped with a motorized lens shift and zoom & focus functionality.

Maximum shift range

The lens can be shifted with respect to the internal optics of the projector (DMD) which results in a shifted image on the screen (Off-Axis). A 100% shift means that the centre point of the projected image is shifted by half the screen size. In other words, the centre point of the projected image falls together with the outline of the image in an On-Axis projection. Due to mechanical and optical limitations the shift range is limited as well.

All lenses hav e a shift range of 50% up, 50% down, 30% left, and 30% right. This range is valid for all throw ratios. Within these shift ranges the projector a nd lens perform excellently. Conﬁguring the projector outside these shift ranges will result in a slight decline of image quality.

+50%

-50%

-30%

+30%

L R

Image 5-10 PDMD. F Field of view.

+50%

SIDE VIEW

-30% +30%

-50% D

TOP VIEW

It’s mechanical possible to shift ou tside the recommended ﬁeld of view (±90% UP/DOWN and ±50% LEFT/RIGHT), but this will result in a decline of image quality depending on the used lens and the zoom position of the used lens. Furthermore, shifting too much in both directions will result in a blurred image corner.

How to shift the lens of the DP2K SLP-series ?

1. U se the up and down arrow buttons on the Local Keypad to s hift the lens vertically and use the left and right arrow buttons on the Local Keypa d to shift the lens horizontally.

SHIFT

Image 5-11

How to zoom in or out?

1. Use the “+” and “-” zoom buttons on the Local Keypad to zoom in or out.

ZOOM

Image 5-12

How to focus?

1. U se the “+” and “-” focus

FOCUS

Image 5-13

38 R5906847 DP2K SLP SERIES 02/06/2017

buttons on the Local Keypad to focus the image on the screen.

Page 43

5. Lenses & Lens selection

Take into account that the lens focus may slightly drift while the lens is warming up from cold to operation temperature. This is a typical phenomen on for projection lenses used with high brightness projectors. The operation tem pe rature of the lens is reached after approximately 30 minutes pro jection of average video.

Button backlight colors

• BLUE : The default backlight color of the Shift, Zoom and Focus buttons is blue which indicates that the button is enabled.

• PURPLE : When pushing the Shift, Zoom or Focus button the bac klight color is purple of the part of the button that is pushed.

This indicates that the requested action is ongoing.

• RED : The backlight color of the Shift, Zoom and Focus buttons is red in case of end of range.

R5906847 DP2K SLP SERIES 02/06/2017

Page 44

5. Lenses & Lens selection

40 R5906847 DP2K SLP SERIES 02/06/2017

Page 45

6. Input & Communication

6. INPUT & COMMUNICATION

About this chapter

This chapter describes the functionality of t he Local Keyp ad, the projector Status Light (tail light) and the different input and communication ports of your DP2K SLP-series.

Note that all information about the ICMP is gathered into one separated c hapter: "ICMP", page 53.

Overview

• Introduction

• Local Keypad

• Projector Status

• Integrated Cinema Processor (ICP)

• HD-SDI Input Module (optional)

• Integrated Media Block/Server (optional)

• Cinema Controller

R5906847 DP2K SLP SERIES 02/06/2017

Page 46

6. Input & Communication

6.1 Introduction

General

The Input & Communication side of the DP2K SLP-series consists of a Local Keypad integrated into the projector housing and a card cag e with three slots. The rear side of the p rojector is equipped with a tail light which reﬂects the status of the projector.

Depending on the projector conﬁguration the projector card cage is equipped with an ICP or ICMP. See illustration below. In case an ICP is installed then an IMB, IMS , or HDSDI input module can be optionally inserted into the slot below the ICP. Note that all information a bout the ICMP is gathered into one separated chapter: "ICMP", page 53.

Image 6-1 1 Projector status light. 2 Power ON/OFF switch. 3 Local keypad. 4 Barco Cinema Controller. 5ICMP. 6 Input slot for IMB, IMS, or HD-SDI input module (in case no ICMP is installed. 7ICP.

2 4 5 6 7

CAUTION: A unit may only be removed from the card cage by qualiﬁed service personnel. Removing one of

the boards (except for the Cinema Controller) will resu lt in an authorization request u pon starting.

42 R5906847 DP2K SLP SERIES 02/06/2017

Page 47

6.2 Local Keypad

ZOOM

SHIFT

Identiﬁcation of the buttons

6. Input & Communication

21 3 4 5 6 7

8 9 10 11 12

1 4

2 5

DOWSER

FOCUS

SHIFT

ZOOM

3 6

Image 6-2

Functionality of the buttons

Numeric buttons (No.1 - 6)

All the Numeric buttons (reference 1 image 6-2) of the Local Keypad have a blue backlight during normal operation. When the authorization process is activated with the (security) Key button, the backlight color of the Numeric buttons changes to yellow. Each button can be linked to a macro which allows you to setup the projector to your requirements with one push of a button. The backlight color of the Numeric button is green if the macro associated with the Num eric key is activated. The backlight color of the Numeric button is red in case one of the actions of the macro failed.

Marker area

Each Numeric button has a marker area (reference 2 image 6-2) where you can w rite down the name of the Macro.

Standby button

Standby button (reference 3 image 6-2) switches the light source immediately ON or OFF. The light source cooling fans remain active for about 5 minutes. The speed of the other fans is reduced. The backlight color of the Standby button remains red in standby mode and changes to green in operation mode.

Dowser button

The D o wser button (reference 4 image 6-2) opens or closes the electronic dowser. The backlight c olor of the Dowser button is green when the dowser is open and red when the dowser is closed.

Test Pattern bu tton

The Test Pattern button (reference 5 image 6-2) gives direct a ccess to a limited set of the internal test patterns of the projector. This is a toggle button. To exit the Test Pattern mode toggle through all test patterns. Note that the convergence test pattern is not included in this set. The backlight color of the Test Pattern button is red if one of the test patterns is activated and green if none is activated.

Focus button

The F oc us button (reference 6 image 6-2) allows you to focus the projected image on the screen. The backlight color of the Focus button is red in case the end of range is reached.

Shift button

The Shift button (reference 7 image 6-2) allows you to shift the lens up/down or left/right. The backlight color of the Shift button is red in case the end of range is reached.

R5906847 DP2K SLP SERIES 02/06/2017

Page 48

6. Input & Communication

Sleep button

Pushing the S leep button (reference 8 image 6-2) for 3 seconds puts the projector in Sleep mode (energy saving). In c ase the projector is processing the after cooling cycle then the projector goes in Sleep mode after ﬁnishing the after cooling cycle. The backlight c olor of the Sleep button is purple during after cooling and red in Sleep mode.

Push the Sleep button for 3 seconds in Sleep mode to awake t he projector (put in Standby). The backlight color of the Sleep button in Standby mode is green.

Enter or leave Sleep mode can also be done via a 2 dedicated projector command (US B/Ethernet), or via two predeﬁned Macros (not editable) with GPIO, or via the C omm unicator.

The Sleep button is disabled if the light source is on (no backlight).

Star button

Star button (reference 9 image 6-2). Pressing the Star button a few seconds will activate the ICMP reset process.

Key bu tton

The (security) Key button (reference 10 image 6-2) is used for the authorization procedure to clear tamper errors etc. (service purposes). Pin codes can be added/changed with the Communicator.

Zoom button

The Zoom button (reference 11 image 6-2) allows you to zoom in or out the projected image on the screen. The backlight color of the Zoom button is red in case the end of range is reached.

Media control buttons

Buttons (reference 12 image 6-2) allowing you to navigate through the content on the integrated media server. The Media buttons are disabled (no backlight) if no IMS or IMB is installed.

Button backlight colors

• BLUE : The default backlight color of the buttons is blue which indicates that the button is enabled. The buttons of which the

backlight doesn ’t light up are disa bled (E.g. Media Control buttons are dis abled in case no IMB or IMS is installed).

• PURPLE : The backlight color of a button (or part of) is purple when p u shed. This indicates that the requested action is ongoing.

The backlight color remains purple until the requested action is ﬁnished.

• GREEN : depending on t he button the green backlight color can have a different meaning:

- for the Standby button a green backlight color means that the light source is switched ON.

- for the Sleep button a green backlight color means that the projector is awake.

- for the Dowser button a green backlight color means that the electronic dowser is open (applied source can be displayed).

- for the Test Pattern button a green backlight color means that NO test pattern is activated and thus the applied source can be displayed.

- for the Macro buttons a green backlight color means that the associated macro is suc cessfully activated.

- for the Key button a green backlight color m eans that the projector is secured (no tamper event).

• RED : depending on the button the red backlight color can have a different meaning:

- for the Standby button a red backlight color indicates that the light source is OFF (not activated).

- for the Sleep button a red backlight color indicates that the projector is in Sleep mode.

- for the Dowser button a red backlight color indicates that the electronic dowser is closed (applied source can not be dis played).

- for the Test Pattern button a red backlight color indicates that a test pattern is selected (applied source can not be displayed).

- for a Macro button a red backlight color indicates that projector could not execute all actions of the macro (error).

- for the Shift, Zoom or Focus button a re d backlight color indicates that the end of range is reached.

- for the Key button a red backlight color means that the projector is not secured (tamper event).

• YELLOW : The backlight color of t he Numeric buttons 1 to 6 of the Local Keypad changes from blue to yellow if the (security)

Key button is pressed.

R5906847 DP2K SLP SERIES 02/06/2017

Page 49

6. Input & Communication

6.3 Projector Status

About the projector Status Light

The projector Status Light is located at the rear end of the projector (Tail Light). The projector Status Light is real time indicator of the projector condition.

Image 6-3

Status overview

Depending on the condition of the projector the status light may have 4 colors: G reen, Yellow, Red or Blue. Each color represent a different state:

Blinking Green Projector is booting up. (Fully booted up when Test Pattern button is green as well)

Full Green Projector is running normally.

Yellow Projector is running with warnings. Event can go on, but a technical intervention w ill be necessary in

Red Projector is in error state. Problem can prevent normal operation. Solve the problem before

Blue

the near future to prevent a complete stop of the projector.

continuing with the projector.

Projector runs in notiﬁcation state. Maintenance action required.

Standby mode

In Standby mode the light source of the pr ojector is turned OF F, but all the electronics of the projector remain fully operational. The projector is ready to start up the light source ON mode (fully operational).

source and project the image. The status light is not different between Standby mode a nd light

Sleep mode

If the projector is in Sleep mode then the status light ﬂashes every ten se conds. The color of the ﬂash depends on the state of the projector. In other words, the color of the ﬂash will be green in normal state (no warnings, no errors, no notiﬁcations).

In Sleep mode the total power consumption of the projector is less than 15 W. No fans are turning and the Light Source is switched OFF. Only the following functionalities of the projector remains active:

• Cinema Controller

• Local Keypad

• Router and external switch fully functional

• USB IN port type “B” (Virtual comport RS232)

• USB OUT port type “A” (To power handheld devices [500mA MAX]. No other functionality supported)

• GPIO port on the Cinema Controller

Pressing the Sleep button in Standby mode for 3 seconds puts the projector in Sleep mode. In ca se the projector is processing the after cooling cy cle then the projector goes in Sleep mode after ﬁnishing the after cooling cycle.

Pressing the Sleep button in Sleep mode for 3 seconds will awake the projector. The status light will blink for a few seconds (booting up all inactive boards) and then lights up continuously.

Enter or leave Sleep mode can also be done via 2 dedicated projector com mand (USB/Ethernet), or via two predeﬁned Macros (not editable) with G PIO of the Cinema Controller (not the GPIO of the ICMP), or via the Comm unicator.

The projector always boots up in the same mode (E.g. Standby or Sleep) as it was switched OFF.

The Sleep button is disabled if the Light Source is on.

R5906847 DP2K SLP SERIES 02/06/2017 45

Page 50

6. Input & Communication

6.4 Integrated Cinema Processor (ICP)

In case the projector is equipped with a Barco ICMP no ICP board is inserted. All ICP functionality is integrated in the Barco ICMP.

LEDs and ports on the Integrated Cinema Processor

1 2

ICP

POWER

Image 6-4 1 ICP is powered. 2 ICP software state, normal operation is green blinking. 3 ICP operating system state, normally full green . 4ICPFMTconﬁguration state, normally full green. 5ICPMAINconﬁguration state, normally full green. 6 CINEMA port selected. When on, LE D 7 will be out. 7 ALTERNATIVE port selection. When on, LED 6 will be out. (note that this function is disabled. Led never lights up) 8 USB, for future use. 9 USB, for future use.

SW STATOSSTAT

FMT STAT

6 7 8 9

ICP

STAT CINEMA

CONT

USB

ALT

OUT

LED diagnostic

State description

Software state (LED reference 2) ﬂashing green

Operating System state (LED reference 3)

FMT FPGA stat e (LED reference 4)

ICP FPGA state (L ED reference 5)

Normal operation Error state

red or orange

green

off, red or yellow

red : unable to conﬁgure the FPGA

yellow : FPGA is loaded with the Boot

green

application red : unable to conﬁgure the FPGA

yellow : FPGA is loaded with the Boot application

USB

ICP functions:

• Stores all projector ﬁles. When board is replaced; clone package must be reloaded.

• Stores and generates test patterns.

• Scaling to native resolution, re-sizing, masking, line-insertion de-interlacing, subtitle overlay, color space conversion, de-gamma, color correction

• Source Selection between alternative content and cinema content.

• Stores a C e rt i ﬁcate and Private Key needed for Playback validation

• Contains a real time clock, which must be synchronized with the GM T /UTC time stored in the link decryptor module or Integrated Media Block (see Com municator software)

• Handles unpacking of special video formats

The ICP board spare part kit is not default programmed for a DP2K SLP-series projector. When using this board in a DP2K SLP-series projector the software must be re-installed after installation of the board.

When installing a new ICP board in a DP2K SLP-series pro jector the Spatial Color Calibration ﬁle must be reloaded and activated.

CAUTION: Make sure not to short circuit the battery on the board. That will destroy the board completely !

46 R5906847 DP2K SLP SERIES 02/06/2017

Page 51

6.5 HD-SDI Input Module (optional)

Depending on the projector conﬁguration the projector card cage is either equipped with an ICP or ICMP. In case an ICP is installed then an IMB , IMS, or HDSDI input module can be optionally inserted into the slot below the ICP. This is n ot the case if the ICMP is installed. For more information about the ICMP see chapter called ICMP.

Location of the source input ports

6. Input & Communication

1 2

SMPTE 292/424 IN

SEL

Image 6-5 1 SMPTE 292/424 input, port A (maximum cable length of 30 m allowed) 2 SMPTE 292/424 input, port B (maximum cable length of 30 m allowed)

SMPTE

Society of Motion Picture and Television Engineers - A global organization, based in the United States, that sets standards for b aseband visual communications. This includes ﬁlm as well as video standards.

HD-SDI settings

Source: 2K

General settings Advanced settings

Port Port type Mode Scan type Color

AorB

HDSDI Single link 4:2:2 10

bits/color

Progressive

Progressive - ﬁeld bit normal

Progressive - ﬁeld bit inverted

Progressive SF - 2nd ﬁeld dominant

Progressive SF - 1st ﬁeld dominant

3GSDI link

Progressive Y C bCr

bits/color

space

YCbCr HDSDI-Single link Single

SYNC OK

Pixel mapping Calibration

3G-level A-Single link4:2:2 12

Single

3G-level B-Dual link

4:4:4 10

Progressive

RGB

3G-level A-Single link

bits/color

3G-level B-Dual link

4:4:4 12

Progressive

XYZ/RGB

3G-level A-Single link

bits/color

3G-level B-Dual link

R5906847 DP2K SLP SERIES 02/06/2017 47

Page 52

6. Input & Communication

Port Port type Mode

A+B

HDSDI D uallink AB

General settings

Scan type Color

4:4:4 10 bits/color

4:4:4 12 bits/color

Progressive

Progressive - ﬁeld bit normal

Progressive - ﬁeld bit inverted

Progressive SF - 2nd ﬁeld dominant

Progressive SF - 1st ﬁeld dominant

Progressive

Progressive - ﬁeld bit normal

Progressive - ﬁeld bit inverted

Progressive SF- 2nd ﬁeld dominant

Progressive SF - 1st ﬁeld dominant

Source: 2K

space

RGB

XYZ/RGB

Advanced settings

Pixel mapping

HDSDI-Dual link Single

Calibration

General settings

Port Port type Mode

AorB

A+B

3GSDI link - 3D

HDSDI 3D

3GSDI 3D

4:2:2 10 bits/color

4:2:2 12 bits/color

4:4:4 10 bits/color

Source: 2K-3D

Scan type Color

Progressive

ﬁeld dominant

Progressive SF - 2nd ﬁeld dominant

Progressive

ﬁeld dominant

Progressive SF - 2nd ﬁeld dominant

Progressive

Progressive RG B

space

YCbCr 3G - Level B - Dual

YCbCr HDSDI - Interleaved

YCbCr

Advanced settings

Pixel mapping

stream

Interleaved

3G - Level B Interleaved

Interleaved

Calibration

Single

Dual (separate left / right eye)

SingleProgressive SF - 1st

Dual (separate left / right eye)

Single

Dual (separate left / right eye)

Single

Dual (separate left / right eye)

SingleProgressive SF - 1st

Dual (separate left / right eye)

Single

Dual (separate left / right eye)

Single3G - Level A -

Dual (separate left / right eye)

Single

Dual (separate left / right eye)

Single3G - Level A -

Dual (separate left / right eye)

R5906847 DP2K SLP SERIES 02/06/2017

Page 53

General settings

Port Port type Mode

4:4:4 12 bits/color

General settings

Port Port type Mode

AorB

A+B

3GSDI link - H F R

HDSDI HFR

3GSDI HFR

4:2:2 10 bits/color

4:2:2 12 bits/color

4:4:4 10 bits/color

4:4:4 12 bits/color

Source: 2K-3D

Scan type Color

Progressive X YR/RGB

Source: 2K-HFR

Scan type Color

Progressive

Progressive SF - 1st ﬁeld dominant

Progressive SF - 2nd ﬁeld dominant

Progressive

space

YCbCr

YCbCr HDSDI - Interleaved Single

YCbCr

RGB

XYZ/RGB

6. Input & Communication

Advanced settings

Pixel mapping

Interleaved

3G - Level B Interleaved

Advanced settings

Pixel mapping

3G - Level B - Dual stream

3G - Level B - Single link

3G - Level A Interleaved

3G - Level B Interleaved

3G - Level A Interleaved

3G - Level B Interleaved

3G - Level A Interleaved

3G - Level B Interleaved

Calibration

Single3G - Level B -

Dual (separate left / right eye)

Single3G - Level A -

Dual (separate left / right eye)

Single

Dual (separate left / right eye)

Calibration

Single

Source: 3D-HFR

General settings

Port Port type Mode

A+B

R5906847 DP2K SLP SERIES 02/06/2017 49

3GSDI 3D HFR

4:2:2 10 bits/color

Scan type Color

Progressive

ﬁeld dominant

Progressive SF- 2nd ﬁeld dominant

space

YCbCr 3G - Le vel A -

Advanced settings

Pixel mapping

Interleaved

Calibration

Single

Dual (separate left / right eye)

SingleProgressive SF - 1st

Dual (separate left / right eye)

Single

Dual (separate left / right eye)

Page 54

6. Input & Communication

6.6 Integrated Media Block/Server (optional)

Integrated Media Block (IMB)

Image 6-6 Example of IMB powered by Doremi.

Integrated Media Server (IMS)

Image 6-7 Example of IMS powered by Doremi.

Conﬁguration and operation instructions for IMB and IMS are not included in this document. See manufacturers website of the installed IMB/IMS for technical documentation and support.

50 R5906847 DP2K SLP SERIES 02/06/2017

Page 55

6.7 Cinema Controller

Location of the communication ports

Image 6-8

Functionality

Diagnostic LEDs

The front plate of the Cinema Controller contains 4 diagnostic LEDs to display the status o

• +VTEC supply (not used on DP2K-S series projector).

• +24V supply.

• +12V supply.

• general power supply (ERROR).

6. Input & Communication

5 6 74321

f the power supply:

USBINport

The Cinema Controller is equipped with a USB port, type “B” connector to connect upstream devices (E.g. PC). This USB port is us ed to commun icate with the projector via RS232 commands (Virtual comport).

USB OUT port

The Cinema Controller is equipped with a USB port, type “A” connector which can be used to power handheld devices within USB spec (MAX 500mA/5V]. No other functionality supported (Future expansion).

3D INTERFACE

3D interface port can be used to connect external 3D devices to the projector. All signals necessary for 3D projection can be provided via this connector.

GENERAL PURPOSE INPUT/OUTPUT (GPIO)

This 37 pin connector can be used to send or receive trigger signals from other d evices. These input/output pins can be programmed by macros created with the Communic ator software. See user ’s guide of the Communicator, section Macro editor, for more information about this functionality. Note that the General Purpose Inputs accept 24 volt maximum. If the factory predeﬁned macro to wake up the projector is assigned to one of the free GPI input pins the projector can be awakened via GPIO.

Wide Area Network (WAN)

Wide Area Network (WAN: 10/100/1000 base-T). Use this Ethernet port (reference 6 image 7-8) to connect the network which contains the DHCP server.

Once connected to the WAN, users can access the projector from any location, inside or outside (if allowed) their company network us ing the Communicator software. This software locates the projector on the network if there is a DHC P server or the us er can insert the correct IP-address to access the p rojector. O nce accessed, it is possible to check and manipulate all the pr ojector settings. Remote diagnostics, control and monitoring of the projector can then become a daily and very simple operation. The network connectivity allows detection of potential errors and conseq uently improves service time.

Local Area Network (LAN: 10/100/1000 b ase-T)

Local Are a Network (LAN: 10/100/1000 ba se-T) with built-in Ethernet switch (port I and port II). Use for projector control and automation. E.g. Touch Panel, content server, ... (not for content streaming!)

As there is a need to daisy chain projectors when they are on an Ethernet network, an Ethernet switch is built in. the incoming network is hereby available for the internal PC and for the next device in the chain. In this way a ’star’ network interconnection can be avoided. The switch used is a stand alone 10/100/1000Mbit Ethernet switch. This assures no inﬂuence on the network speed.

The connectors used for these Ethernet ports Straight (most c omm on) as well as cross linked network cables can be used. The 2 ports are functionally identical. B oth ports are connected via the projector switch (Auto sensing enabled).

R5906847 DP2K SLP SERIES 02/06/2017

are of the type RJ45, which is compatible with standard RJ45 cable connector.

Page 56

6. Input & Communication

The connectors used for all Ethernet ports are of the type RJ45, which is compatible with standard RJ45 cable connector. Straight (most common) as well as cross linked network cables can be used. The 2 ports are functionally identical. Both ports are connected via the p rojector switch (Auto sensing enabled).

Virtual comport (RS232 serial communication)

The USB-IN port of the com munication interface supports RS 232 serial comm unication. You can use the RS232 input port to connect a local PC to the projector. This way you can conﬁgure and control the projector from your local PC.

Do not forget to set the projector’s baud rate (default = 115200) to match that of the computer.

Advantages of using RS232 serial communication:

• easy adjustment of the projector via PC (or MAC).

• wide range of control possibilities.

• sending data to the projector (update).

• copying data from the projector (backup).

RS232

An Electronic Industries Association ( EIA) serial digital interface standard spec ifying the characteristics of the com m unication path between tw o devices using either D-SUB 9 pins or D- SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to b e used. The standard speciﬁes com ponent connection standards with regard to c omputer interface. It is also c alled RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical ’0’ is > + 3V, Logical ’1’ is < 3V. The range between -3V and +3V is the transition zone.

52 R5906847 DP2K SLP SERIES 02/06/2017

Page 57

7. ICMP

About this chapter

This chapter describes the ICMP in general, the HDDs, the input p orts and the communication ports. Fu rthermore, the s tatus LEDs are described and the importance of the device certiﬁcate is illustrated.

Image 7-1

7. ICMP

Overview

• ICMP introduction

• ICMP HDD

• ICMP communication ports

• ICMP source input ports

• ICMP DisplayPort speciﬁcations

• ICMP SDI speciﬁcations

• ICMP HDMI 2.0 speciﬁcations

• ICMP HDMI 1.4 speciﬁcations

• ICMP status LEDs

• ICMP HDD status LEDs

• ICMP device certiﬁcate

•ICMPconﬁguration via Communicator

• ICMP reset

• Obtaining the Barco ICM P certiﬁcate

• Removing a HDD from the ICMP

• Installing a HDD into the ICMP

R5906847 DP2K SLP SERIES 02/06/2017

Page 58

7. ICMP

7.1 ICMP introduction

About ICMP

The ICMP is a rem ovable electronic assembly situated in the Card Cage of the projector. The ICMP stores, decrypts and decodes DCI cinema content and delivers it to the projector in a usable format, all integrated into a single assembly plac ed directly in the projector. ICMP is a fully integrated assem bly so expected by the operators to facilitate their daily business.

The standard Integrated Cinema Processor functionality from Texas Instruments® is fully integrated into the ICMP. So, the ICMP replaces the ICP b oard as well.

Image 7-2 1ICMP 2 HDDs for ICMP

As an integrated component of the projector, installation and maintenance of the ICMP requires the same skills and the same precautions as an intervention on the projector itself.

For order info see w

ww.barco.com.

Front face of the ICMP

The last produced model is equipped with two HDMI 2.0 as video source.

Image 7-3 Front face ICM P (with HDMI 2.0).

Some models with DisplayPorts are still present on the ﬁeld.

Image 7-4 Front face ICMP (with DisplayPort).

54 R5906847 DP2K SLP SERIES 02/06/2017

Page 59

7. ICMP

Card Cage slot location

The Card Cage can be different depend ing the projector type but it always consists of a button module and several removable units. The I CM P (reference 1) is inserted into the former ICP slot and IMB slot above the Barco Cinema Controller (reference 2).

ICMP location in the Card Cage of a S-series projector.

Image 7-5

R5906847 DP2K SLP SERIES 02/06/2017 55

Page 60

7. ICMP

7.2 ICMP HDD

About ICMP HDD

The three HDDs (local storage) in the ICMP, are set up in a RAID 5 conﬁguration. This storage technique, that combines multiple HDD components into a logical unit, manages enough redundancy information to continue to operate properly after the loss of one HDD.

Image 7-6

CAUTION: A RAID 5 conﬁguration with three HDDs allows a maximum loss of one disk. With the si

loss of more than one HDDs, data is lost and the RAID must be completely initialized again after replacement of the defect HDDs with new HDDs!

multaneous

About degraded mode

When a RA ID array experiences the failure of one disk, it enters in degraded mode. C ontent storage and playback remains available on the ICMP.

CAUTION: T he loss of one disk causes no serious consequences on the ICMP. But action must be taken

quickly because the loss o f a second disk will make the R AID system broken. The main cause o f the total loss of RAID is due in most cases to the loss of the second disk while t

A failed drive should be replaced as soon as possible.

he ﬁrst has not been rebuilt!

About “RAID recovery” process

The restoration from degraded to normal condition of the RAID 5 system is done automatically. When the RAID controller detects a new HDD to replace the failed disk the recovery procedure starts automatically.

CAUTION: The automatic p rocess does not work if more than one disk is lost. In that ca se the RAID must be

completely initialized again!

About RAID broken

When more than one HDD is out of order, the RAID is considered as ’broken’ and the content is lost. The failed HDDs must be changed and a n ew RAID must be created.

Exchange or re-use of a disk set

It’s possible to h ave several sets of di ICMP.Itissufﬁcient to insert the three HDDs, from a v alid RAID array, and let the system explore the new RAID. The mounting order of the HDDs and the HDD slots do not matter. Of course, when using HDDs from another ICMP it is necessary to retrieve from the content distributor the KDMs corre

sks with one ICMP or to reuse a complete set of disks coming from another projector with

sponding to the content and the new ICMP.

HDD storage capacity

Make sure that all HDDs in the ICMP HDD set have the same storage capacity. See label on top of the HDD to know the storage capacity.

HDD storage

The maximum recom mended storage period for the drive in a non-operational environment is 90 days. Drives s hould be stored in the original unopened shipping packaging whenever possible. Once the drive is remove d from the o riginal packaging the recommended maximum period between drive opera tion cycles is 30 days. During any storage period the drive non-operational temperature, humidity, wet bulb, atmospheric conditions, shock, vibration, magnetic and electrical ﬁeld speciﬁcations should be followed.

R5906847 DP2K SLP SERIES 02/06/2017

Page 61

7.3 ICMP communication ports

Location of the communication ports

1 2 3 4 5 6 7

Image 7-7 ICMP (with HDMI 2.0).

Functionality

AUDIO-AES 1-8 (9-16)

ICMP outputs sixteen audio signals e quitably distributed over these two RJ45 connectors, which can be conﬁgured independently. The mapping of audio channels (content) on each audio output (AES outputs of the ICMP) is performed by conﬁguring the ICMP via the Communicator software. Please refer to the Com municator user guide for further information.

7. ICMP

GPO 1-4 (5-8)

These RJ45 c onnectors can be used to send trigger signals to other d evices. The mapping of user Cues (output Cues) on each General Purpose Output (GPO) is conﬁgured via the Communicator software. Please refer to the Communic ator user guide for further information.

GPI 1-4 (5-8)

These RJ45 connectors can b e used to receive trigger signals from other devices. The mapping of the G enera l Purpose Input (GPI) on each input Cues is conﬁgured via the Communicator software. Please refer to the Communicator user guide for further information.

SYNC IN / OUT

Synchronization signal IN and OUT: Reserved for multiple-projector projection. Use a 50 Ohm coaxial cable to connect the sync signal from projector to projector.

LAN 1 (2)

The ICMP can be connected to a LAN (local area network) using one of the Ethernet ports. These LA N por t are used for ‘content’ transfer.

NOTE: Thes e ports are optionally used to connect to external content storage sources. Control of the ICMP is done via the same IP address as the projector.

USB 2.0

The ICMP can be connected to a USB 2.0 Media to load content. The USB port can be used to load content (DCP) or keys (KD M).

NOTE: It is recommended to use the USB 3.0 ports for faster ingest.

USB 3.0

The ICMP can be connected to a USB 3.0 Media t keys (KDM), or software update.

NOTE: These ports are recommended for fast ingest when c onnected to an appropriate USB 3.0 source.

R5906847 DP2K SLP SERIES 02/06/2017

o load content. The USB port can be used to load content (DCP), o r

Page 62

7. ICMP

USB

Universal Serial Bus (USB) is an industry standard developed in the mid-1990s that deﬁnes the cables, connectors and communications protocols used in a bus for connection, communication, a nd power supply between computers and electronic devices. US B 2.0 (also called "Hi-Speed"), adding higher maximum signaling rate of 480 Mbit/s (effective throughput up to 35 MB/s or 280 Mbit/s), in addition to the "USB 1.x Full Speed" signaling rate of 12 Mbit/s.[16] USB 2.0 connectors are usually c olored black. USB 3.0 deﬁnes a new SuperSpeed mode with a signaling speed of 5 Gbit/s and a usable data rate of up to 4 Gbit/s (500 M B/s). A USB 3.0 port is usually colored blue, and is backwards compa tible with USB 2.0.

58 R5906847 DP2K SLP SERIES 02/06/2017

Page 63

7.4 ICMP source input ports

Location of the source input ports

The last produced m odel is equipped with two HDMI 2.0 (Reference 8 image 7-8) as video source.

89 10

Image 7-8 ICMP (with HDMI 2.0).

Some models with DisplayPorts (Reference 11 image 7-9) are still present on the ﬁeld.

7. ICMP

119 10

Image 7-9 ICMP (with Display Po rt).

Functionality

HDMI A (B)

HDMI 2.0 connector to connect a video source.

NOTE: It is recommended to use the HDMI 2.0 ports for faster transfer of video and audio data.

3G-SDI A (B)

SDI connector to connect a vid

HDMI

HDMI 1.4 connector to connect a video source.

DisplayPort A (B)

DisplayPort connector to connect a video source.

R5906847 DP2K SLP SERIES 02/06/2017

eo source.

Page 64

7. ICMP

7.5 ICMP DisplayPort speciﬁcations

DisplayPort

Digital display interface developed by the Video Electronics Standards Association (VE SA ). This royalty-free interface is primarily used to connect a video source to a display device such a s a computer monitor, though it can also be us ed to transmit audio, USB, and other forms of data. VESA designed it to replace VGA, DVI, and FPD-Link. Backward compatibility to VGA and DVI by using active adapter dongles enables users to use DisplayPort ﬁtted video sources without replacing existing display devices.

HDCP

High-bandwidth Digital Content P rotection is a form of digital copy protection developed by Intel Corporation to prevent copying of digital audio and video content as it travels across DisplayPort, Digital Visual Interface (DVI), High-Deﬁnition Multimedia Interface (HDMI), Gigabit Video Interface (GVIF), or Uniﬁed Display Interface (UDI) connections, even if such copying would be permitted by fair use laws. The speciﬁcation is proprietary, and implementing HDCP requires a license.

DisplayPort speciﬁca tions

Supported Modes:

• DP1.1a, 4-lanes RBR/HBR

• Audio : yes

• Content Protection : HDCP1.4

• Color Depth : 8 bit/component and 10 bit/component.

• 3D-stereo mode : frame sequential (embedded stereosync on D P required from the source)

DisplayPort A and DisplayPort B accept the following video-timings:

2D Formats / Single DP Color depth Port Display Mode

640 x 480 @ 60 fps 8 bpc, 10 bpc Single 2D

800 x 600 @ 60 fps 8 bpc, 10 bpc Single 2D

1600 x 1200 @ 60 fps 8 bpc, 10 bpc Single 2D

1280 x 800 @ 60 fps 8 bpc, 10 bpc Single 2D

1280 x 720 @ 60 fps

1680 x 1050 @ 60 fps

1920 x 1080 @ 60 fps

1920 x 1200 @ 60 fps

2048 x 1080 @ 48, 60 fps

2048 x 1536 @ 60 fps

2048 x 2160 @ 30, 48, 50, 60 fps

3840 x 2160 @ 24 fps

3D Formats / Single DP Color depth Port Display Mode

1920 x 1080 @ 60 fps 8 bpc, 10 bpc Single 3D

2048 x 1080 @ 60 fps 8 bpc, 10 bpc Single 3D

4K Horizontal SPAN 2D - Full Color depth Port Display Mode

2048 x 2160 @ 30, 48, 50, 60 fps

8 bpc, 10 bpc

8 bpc, 10 bpc A+B span 2D

Single

4K Horizontal SPAN 2D - Flat Color depth

1920 x 2160 @ 30, 48, 50, 60 fps

4K Horizontal SPAN 3D Color depth

2048 x 2160 @ 60 fps

Port Display Mode

8 bpc, 10 bpc A+B span 2D

Port Display Mode

8 bpc, 10 bpc A+B span 3D

R5906847 DP2K SLP SERIES 02/06/2017

Page 65

7. ICMP

Audio formats

• 2 channels / LPCM / 16 bits / 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz

• 5.1 format / LPCM / 24 bits / 48 kHz

• 7.1 format / LPCM / 20 bits / 48 kHz

Notes:

• DisplayMode = Single : is applicable to both DisplayPort A, and DisplayPort B input, se parately.

• DisplayMode = A+B : inputs DisplayPort A and DisplayPort B are combined to 1 larger image; in this case the 2 DisplayPort links need to be genlocked ( = synchronous and in phase).

• In all cases :

- Color Space - Color Sampling:

YCbCr-4:4:4

YCbCr-4:2:2

RGB - 4:4:4

- Scan Type = progressive.

• Both Nvidia and AMD GPU’s will not support color depths of 10 bits/color wh ile in 3D-stereo mode.

• Some Graphical Cards may not permit 10 bits/color at all video timings, because of bandwidth restrictions.

• DisplayPort A and DisplayPort B automatically detect:

- Active Pixels, an d Active Lines

- Vertical Refresh

- 8 bits/color - 10 bits/color

- Frame locked

• All input resolutions are scaled towards the desired resolution speciﬁed in the screen presentation ﬁle.

• Fractional frame rates = (Hz*1000)/1001

R5906847 DP2K SLP SERIES 02/06/2017

Page 66

7. ICMP

7.6 ICMP SDI speciﬁcations

3G-SDI

Serial Digital Interface (SDI) is a s erial link standardized by ITU-R BT.656 and the Society of Motion Picture and Television Engineers (SMPTE). SDI transmits uncompressed d igital video over 75-ohm coaxial cable within studios, and is seen on most professional video infrastructure equipment. The ﬁrst revision of the standard, SMPTE 259M, was deﬁned to carry digital representation of analog video su ch as NTSC and PAL over a ser ial interface and is more popularly known as standard-deﬁnition (SD) SDI. The data rate required to transmit SD SDI is 270 Mbps. Wit of h igh-deﬁnition (HD) video standards such as 1080i and 720p, the interface was scaled to handle higher data rates of 1.485 Gbps. The 1.485-Gbps serial interface is commonly called the HD SDI interface and is deﬁned by SMPTE 292M, using the sam e 75-ohm coaxial cable. Studios and other video production facilities have the hardware infrastructure for coaxial cable and have a vested interest in extending the life of their infrastructure. Fortunately, SMPTE recently ratiﬁed a new standard called SMPTE 424M that doubles the SDI data rates to 2.97 Gbps using the same 75-ohm coaxial cable. This new standard, also called 3-Gbps (3G)-SDI, ena picture quality required for 1080p and digital cinema.

SDI terminology

Standard HD -SD I signal

h the advent

invested heavily on

bles higher resolution of

Single Link

1.5Gb/s HD 4:2:2

Standard HD-SDI allows for a single 4:2:2 image to be carried on one cable at 1.485 G b/s. The image uses the Y Cb Cr colorspace and uses a bit de pth of 10 bit per color com ponent.

Due to the data rate limitations only 23.976, 24, 25, 29.970 and 30 fps streams are achievable.

Dual-Link HD-SDI signal

Dual Link

1.5Gb/s

Dual-Link HD-SDI is mainly two standard HD-SDI signals carrying a single image stream split between the two cables. The main advantage is that c olor subsampling is no longer required, and the im age can be transmitted in 4:4:4 quality, which then also allows the RGB (or X YZ ) color space to be used.

The main link will contain a standard HD-SDI signal, the second (enhancement) link contains the missing Cb and Cr samples.

Depending on the implementation the enhancement link could also contain extra information to increase the bit depth.

3G HD-SDI signal

3Gb/s

1080p 50/60

1080p 4:4:4

1080p 50/60 (Level A)

1080p 4:4:4 (Level B)

3G H D-SD I uses a higher data rate (2.97 Gb/s). This allows a single cable interface to achieve the same capabilities of a Dual-Link HD-SDI implementation.

In direct mapping (level A) this is used to achieve higher frame rates. (50, 59.940 and 60 fps streams are supported).

1. Not supported in Alchemy

62 R5906847 DP2K SLP SERIES 02/06/2017

Page 67

7. ICMP

Dual Stream 3G HD-SDI signal

Dual Stream 3G

HD 4:2:2 Signal #1

3Gb/s

Dual Stream 3G is a speciﬁc variant of the 3G signal which combines two com pletely separate 4:2:2 image streams into a single 3G signal. This can be used to transmit stereoscopic streams by keeping the left and right eye signals together.

and

HD 4:2:2 Signal #2

SMPTE 292M STANDARD 1.485 Gb/s HD-SDI SIGNALS

Standard HD-SDI (SMPTE 292M) formats

SMPTE Standard Source Resolution Frame Rate Display Rate Scan Type

SMPTE 296M 1280 x 720 23.976

29.970

59.940

SMPTE 274M

SMPTE 428-8

SMPTE 274M

SMPTE 428-9

(SMPTE RP211)

SMPTE 274M

1920 x 1080

2048 x 1080

1920 x 1080

2048 x 1080

1920 x 1080 25

23.976

29.97

23.976

29.97

29.970

23.976

29.970

59.940

23.976

29.97

23.976

29.97

59.940

Progressive

Y C b Cr 4:2:2 10 -Bit

Progressive

Y C b Cr 4:2:2 10 -Bit

Segmented frame

Y C b Cr 4:2:2 10 -Bit

Interlaced

Y C b Cr 4:2:2 10 -Bit

Dual-Link HD-SDI (SM PTE 372M) formats

SMPTE Standard Source Resolution

SMPTE 274M

SMPTE 428-8

R5906847 DP2K SLP SERIES 02/06/2017 63

1920 x 1080

2048 x 1080

Frame Rate Display Rate

23.976

29.970

23.976

29.970

Scan Type

Progressive

Y Cb Cr 4:2:2 12-Bit only

Y Cb Cr 4:4:4 10 or 12-Bit

RGB (XYZ) 4:4:4 10 or 12-Bit

Page 68

7. ICMP

SMPTE Standard Source Resolution

SMPTE 274M

SMPTE 428-9

1920 x 1080

2048 x 1080

(SMPTE RP211)

SMPTE 274M

1920 x 1080 25

Standard HD-SDI (2 × SMP TE 292M) formats

SMPTE Standard Source Resolution

SMPTE 292M

SMPTE 428-8

SMPTE 292M

SMPTE 428-9

1920 x 1080

2048 x 1080

1920 x 1080

2048 x 1080

(SMPTE RP211)

Frame Rate Display Rate

23.976

29.970

Frame Rate Display Rate

23.976

29.97

23.976

29.97

23.976

29.970

59.940

47.952

59.940

47.952

59.940

Scan Type

Segmented frame

Y Cb Cr 4:2:2 12-Bit only

Y Cb Cr 4:4:4 10 or 12-Bit

RGB (XYZ) 4:4:4 10 or 12-Bit

Interlaced

Y Cb Cr 4:2:2 12-Bit only

Y Cb Cr 4:4:4 10 or 12-Bit

RGB (XYZ) 4:4:4 10 or 12-Bit

Scan Type

Progressive

Y C b Cr 4:2:2 10 -Bit

Segmented frame

Y C b Cr 4:2:2 10 -Bit

The s tandard HD-SDI interfaces support the Y Cb Cr colorspace (both legal and full range) using 4:2:2 color subsampling.

The Dual-Link HD-SDI interface can be used to carry a single 4:4:4 image, having a color depth of 10 or 12 bit per component. Both RGB (XYZ) and Y Cb Cr color spaces are supported.

SMPTE 424M 3G HD-SDI 2.970 Gb/s SIGNALS

3G HD-SDI (SMPTE 425 ) formats

SMPTE Standard Source Resolution

SMPTE 296M

SMPTE 274M

1280 x 720 23.976

1920 x 1080 50

1920 x 1080 23.976

Frame Rate Display Rate

23.976

29.970

59.940

29.970

59.940

23.976

29.97

Scan Type

Progressive

Y C b Cr 4:4:4 10 -Bit

RGB (XYZ) 4:4:4 10-Bit

Progressive

Y C b Cr 4:2:2 10 -Bit

Progressive

Y Cb Cr 4:2:2 12-Bit only

Y Cb Cr 4:4:4 10 or 12-Bit

RGB (XYZ) 4:4:4 10 or 12-Bit

2. mainly used to carry stereoscopic images.

3. only supported in 3G level A mapping, others formats are supported in both level A and level B mapping.

64 R5906847 DP2K SLP SERIES 02/06/2017

Page 69

7. ICMP

SMPTE Standard Source Resolution

SMPTE 274M

SMPTE 428-9

Dual Stream 3G HD-SDI (SM PTE 425) formats

SMPTE Standard Source Resolution Frame Rate Display Rate Scan Type

SMPTE 292M

SMPTE 428-9

1920 x 1080 50

2048 x 1080 23.976

1920 x 1080

2048 x 1080

Frame Rate Display Rate

59.940

23.976

29.970

59.940

23.976

47.952

59.940

Scan Type

Interlaced

Y Cb Cr 4:2:2 12-Bit only

Y Cb Cr 4:4:4 10 or 12-Bit

RGB (XYZ) 4:4:4 10 or 12-Bit

Progressive

Y C b Cr 4:4:4 12 -Bit

RGB (XYZ) 4:4:4 12-Bit

Progressive

Y C b Cr 4:2:2 10 -Bit

R5906847 DP2K SLP SERIES 02/06/2017 65

Page 70

7. ICMP

7.7 ICMP HDMI 2.0 speciﬁcations

HDMI

HDMI (High-Deﬁnition Multimedia Interface) is a compact audio/video interface for transferring uncom pressed video data and compressed/uncompressed digital audio data from a HDMI-compliant device ("the source device") to a compatible computer monitor, video pr ojector, digital television, or digital audio device. HDM I is a digital replacement for existing analog video standards.

HDMI 2.0 speciﬁcations

HDMI

Both HDMI 2.0 inputs are fully compliant with the HDMI 1.4, 1.4a, 1.4b, 2.0 and 2.0a revisions of the HDMI speciﬁcation.

Full Range and Limited Range Quantization are supported for all speciﬁed formats.

BT.709 and DCI-P3 are supported for all formats. For HDR content (UHD and 4K only) the BT.2020 color coding is supported.

All video streams should have a progressive scan order, with the exception of 1920x1080i 60 fps (interlaced scan).

HDCP

Both HDMI 2.0 inputs are HDCP 1.4 & HDCP 2.2 compliant.

HDR (SMPTE ST 2084)

HDR (High Dynamic Range) is supported on all UHD and 4K formats.

This includes SMPTE ST 2084 (static metadata) and BT.2020 color coding. Requires a license!

HDMI 2.0 Cable requirements

All HDM I cables should work with HDMI 2.0 receivers. There is no such thing as a “4K HDMI cable” even though this is sometimes sold this way. But of course there are quality differences. T he “high-speed” cables would be preferred over the “standard-speed” cables. They usually work at higher cable lengths than the standard-speed ones.

The “Premium Certiﬁed HDMI” cables are tested to wor k with high bandwidth as is the case with 4K HDR content. These can be more expensive though. When using active and/or optical cables you should verify if the integrated receiver and sender are HDMI certiﬁed to guarantee to work com pliant with the HDMI protocol. You can request the HDMI certiﬁcate to the manufacturer of the cable.

The ICMP is not supporting Ethernet-over-HDMI and such sp

eciﬁc cables are thus not required.

HDMI 2.0 Supported 2D Formats

Format Frame Rate

1280x720 23.976, 24, 25, 29.97, 30, 50,

1280x720 100, 119.88, 120

1920x1080

2048x1080

1920x1080

2048x1080

59.94, 60

23.976, 24, 25, 29.97, 30, 50,

59.94, 60

100, 119.88, 120

Color coding

RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2

Bit depth

12 8

66 R5906847 DP2K SLP SERIES 02/06/2017

Page 71

7. ICMP

Format Frame Rate

3840x2160

4096x2160

3840x2160

4096x2160

23.976, 24 25, 29.97, 30

50, 59.94, 60

Color coding

RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2

Bit depth

12 8

HDMI 2.0 Supported 3D (Frame Packing) Formats

Format Frame Rate Color coding Bit depth

1920x1080

2048x1080

1920x1080

2048x1080

3840x2160

4096x2160

3840x2160

4096x2160

23.976, 24, 25, 29.97, 30 RG B

YCbCr 4:4:4

YCbCr 4:2:2

50, 59.94, 60 RGB

YCbCr 4:4:4

YCbCr 4:2:2

23.976, 24 25, 29.97, 30 RGB

YCbCr 4:4:4

YCbCr 4:2:2

50, 59.94, 60 RGB

YCbCr 4:4:4

YCbCr 4:2:2

12 8

HDMI 2.0 Supported Audio Formats

Format

2.0

2.1

5.1

7.1

Sample Rate Sample coding

44.1

88.2

L-PCM

HDMI 2.0 Supported Dual (Twin) Link Formats (2D formats only)

Format Frame Rate

1920x1080

2048x1080

3840x2160

4096x2160

In Dual (Twin) Link both HDMI2 inputs (port A & port B) should have to sam e Format, Frame Rate and Color coding.

Port A should contain the 8 most signiﬁcant bits of the p ixel data, where port B sho uld contain the 8 least signiﬁcant bits of the pixel data. The pixel data will be reconstructed using the all 8 bits of port A and using the 4 most signiﬁcantbitsofportB.

23.976, 24, 25, 29.97, 30, 50,

59.94, 60

23.976, 24, 25, 29.97, 30, 50,

59.94, 60

Color coding

RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2

Bit depth

HDMI 2.0 Supported Passive 3D Formats (3D formats only)

Format Frame Rate Color coding Bit depth

1920x1080

2048x1080

R5906847 DP2K SLP SERIES 02/06/2017 67

24, 30 RGB

YCbCr 4:4:4

YCbCr 4:2:2

Page 72

7. ICMP

Format Frame Rate

1920x1080

2048x1080

3840x2160

4096x2160

In Passive 3D HDMI2 input port A should contain the pixel data of Left Eye and HDMI2 input port B should contain the pixel data for Right Eye.

24, 30

Color coding

RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2

Bit depth

68 R5906847 DP2K SLP SERIES 02/06/2017

Page 73

7.8 ICMP HDMI 1.4 speciﬁcations

HDMI

HDMI 1.4 speciﬁcations

HDMI1.4a, including HDCP1.4

HDMI 1.4 Supported 2D Formats (progressive)

Format Frame Rate

720x480 60

720x576 50

1280x720 23.976, 24, 25, 29.97, 30, 50,

1680x720 23.976, 24, 25, 29.97, 30, 50,

1920x1080

2048x1080

1920x1080

2048x1080

2560x1080 23.976, 24, 25, 29.97, 30, 50,

3840x2160

4096x2160

59.94, 60, 100, 119.88, 120

23.976, 24, 25, 29.97, 30, 50,

59.94, 60

100, 119.88, 120

59.94, 60

23.976, 24, 25, 29.97, 30

Color coding

RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2 RGB

YCbCr 4:4:4

YCbCr 4:2:2

7. ICMP

Bit depth

(8)

12 (8)

12 8

HDMI 1.4 Supported 2D (Interlaced) Formats

Format Frame Rate

720x576 25, 50, 100

1920x1080 25, 29.97, 30, 50, 59.94, 60

Color coding

Bit depth

HDMI 1.4 Supported 3D (Frame Packing) Formats

Format Frame Rate Color coding Bit depth

1280x720 50, 59.94, 60

1920x1080 23.98, 24

HDMI 1.4 Supported 3D (Top Bottom) Formats

Format Frame Rate

1280x720 50, 59.94, 60

1920x1080 23.98, 24

R5906847 DP2K SLP SERIES 02/06/2017 69

Color coding

Bit depth

Page 74

7. ICMP

HDMI 1.4 Supported Audio Formats

Format

2 channels 32, 44, 48, 88, 96

5.1 channels 24

7.1 channels 20

Sample Rate Sample coding

L-PCM

Bit depth

70 R5906847 DP2K SLP SERIES 02/06/2017

Page 75

7.9 ICMP status LEDs

ICMP status LEDs and Reset button

LEDs on ICMP front panel give information on the status of the de vice.

Image 7-10

Status overview PWR/ERROR and READY LEDs:

1 2

7. ICMP

PWR/ERROR READY ICMP Status

Off Off Turned off

Red

Blinking Green Off

Blinking Green Blinking Or ange Operating System start up

Blinking Green Orange Security M anager - Image Integrity tests

Blinking Green

Blinking Green Yellow Security Manager - FPGA self-test

Green Blinking Green Starting Applications

Green Green

Green O range

Blinking Red Off FIPS error

Green Blinking Orange

Orange Orange

Off Board reset or FIPS error

Boot loader

Blinking Yellow

Security Manager - Self Test

Applications started in normal mode

Applications started in degraded mode

Update ongoing

Update done

R5906847 DP2K SLP SERIES 02/06/2017 71

Page 76

7. ICMP

7.10 ICMP HDD status LEDs

ICMP HDD status LEDs

Image 7-11

Status overview PWR/ERROR and READY LEDs:

4 5

HDD I/O

Off Off HDD idle / Disk in RAID O K.

Blinking Green Off HDD I/O activity / Disk in RAID OK.

Blinking Green

Off Red HDD idle / Disk error. See troubleshooting table below for curative actions.

RAID

Blinking R ed

ICMP HDD Status

HDD I/O activity / RAID rebuilding.

Troubleshooting

Situation Solution

Onediskfailed(redLED)+RAID degraded.

The ongoing event is not interrupted.

Note: The dis k status (RAID degraded) can be retrieved via the (Web) Com mander. S ee user guide of the (Web) Commander.

One disk failed (red LED) + Error 10580 “local storage not

available”.

Note: The disk status (Error code) can be retrieved via the

(Web) Com mander. S ee user guide of the (Web) Commander.

Multiple disks failed (multiple red LEDs) + RAID broken.

Note: The disk status (RAID broken) can be retrieved via the (Web) Com mander. S ee user guide of the (Web) Commander.

All HDD LEDs remain off + Error 10580 “local storage no t

available”.

Note: The disk status (Error code) can be retrieved via the

(Web) Com mander. S ee user guide of the (Web) Commander.

1. Switch off the pow er.

2. Replace the defect HDD with an original HDD spare part. See procedure "Removing a HDD from the ICMP", page 79, and "Installing a HDD into the ICMP ", page 80. Ensure to insert the HDD ﬁrmly.

3. Switch on the power.

Result: As soon the new HDD is detected by the ICMP the rebuild of the RAID is started (Blinking red LED).

1. Switch off the pow er.

2. Replace the defect HDD with an original HDD spare part. See procedure "Removing a HDD from the ICMP", page 79, and "Installing a HDD into the ICMP ", page 80. Ensure to insert the HDD ﬁrmly.

3. Switch on the power.

Result: As soon the new HDD is detected by the ICMP the rebuild of the RAID is started (Blinking red LED).

1. Switch off the pow er.

2. Replace all defect HDDs with original HDD spare parts. See procedure "Removing a HDD from the ICMP", page 79, and "Installing a HDD into the ICMP ", page 80. Ensure to insert the HDDs ﬁrmly.

3. Switch on the power.

4. Start “RAID Initialize”. See user guide of the Communicator.

Result: a new empty RAID is created.

1. Switch off the pow er.

2. Reseat all HDDs. See procedure "Rem oving a HDD from the IC MP ", page 79, and "Installing a HDD into the ICMP", page 80. Ensure to insert the HDDs ﬁrmly

3. If problem remains try “RAID Initialize”. See user guide of the Communicator. Note that all content will be lost!

4. If problem remains contact Service for further instructions.

72 R5906847 DP2K SLP SERIES 02/06/2017

Page 77

7. ICMP

In case the ICMP has to be returned to factory (e.g. for repair) the non defective HDDs should be removed an d kept.

R5906847 DP2K SLP SERIES 02/06/2017 73

Page 78

7. ICMP

7.11 ICMP device certiﬁcate

Purpose of the Barco ICMP device certiﬁcate

The device certiﬁcate (*.pem) of the Barco ICMP is a digital certiﬁcate s igned by Barco which is required when o rdering the KDM to play a D CP that is ingested on the ICMP. The device certiﬁcate is stored inside the ICMP and on a web server.

The (WEB) Com ma nder or Communicator can be used to retrieve the device certiﬁcate d irectly from the ICMP. To retrieve the device certiﬁcate from the website the QR (Quick R espons e) code can be used. S ee procedure "Obtaining the Barco ICMP certiﬁcate", page 78.

X.509 device certificate

Barco signed

(PKI CA)

BARCO-ICMP-0123456789.pem

Device

Studios

manufacturer

TDL

Content distributors (Key supplier)

.pem

0123456789

KDM DCP

Image 7-12

ICMP

Communicator, Commander, Web Commander.

Trusted Device List (TDL)

The Goal of the T DL is to maintain timely and accurate information on participating auditoriums so that participating subscribers can obtain information needed to issue KDMs. The TDL has several data sources: Device manufacturers, Exhibitors, Deployment Entities, Integrators, Service Providers (interacting with Exhibitors), re gional authorities and Support.

Public Key Infrastructure (PKI)

PKI is a framework for crea foundation of a PKI is the certiﬁcate authority (CA), whic h issues digital certiﬁcates that authenticate the identity of organizations and individuals over a public system such as the Internet. The certiﬁcates are also used to sign messages, which ensures that mes

ting a secure method for exchanging information based on public key cryptography. The

sages have not been tampered with.

74 R5906847 DP2K SLP SERIES 02/06/2017

Page 79

7. ICMP

*.pem

Privacy-enhanced Electronic M ail. File format used to distribute digital signed certiﬁcates. Base64 encoded DER certiﬁcate, enclos e d be t ween "-----BEGIN CE RTI FICATE-----" and "-----END CERTIFI CATE-----"

Key Delivery Message (KDM)

The security key for each movie is delivered in a unique KDM for each digital cinem a server. The security key is encrypted within the KDM, which means that the delivery of a KDM to the wrong server or wr ong location will not work, and thus such errors cannot compromise the security of the movie. The KDM is a small ﬁle, and is typically emailed to the ex hibitor. To create the correct s et of KDMs for a site requires knowledge of the digital certiﬁcate in the projection system´s media b lock.

Digital Cinema Package (DCP)

A Digital Cinema Package (DCP) is a collection of digital ﬁles used to store and convey Digital Cinema (DC) audio, image, and data streams. The term has been deﬁned by Digital Cinema Initiatives (DCI). General practice adopts a ﬁle structure that is organ ized into a number of usually multi-gigabyte size Material eXchange Format (MXF) ﬁles, wh ich are separately used to store audio and video streams, and auxiliary index ﬁles in XML format. The MXF ﬁles contain streams that are compressed, encoded, and encrypted, in order to reduce the huge amount of required storage and to protect from unauthorized use. The image part is JPEG 2000 compressed, whereas the audio part is linear PCM. The adopted (optional) encryption standard is AES 128 bit in CBC mode. T he ne wer SMPTE standards are used to conform the recommendations among different tool vendors and producers. Interop, the legacy DCP standard, is still required to be supported by DCP players.

Digital Cinema Initiatives (DCI)

DCI is a joint venture of Disney, Fox, Paramount, Sony Pictures Entertainment, Universal and Warner Bros. Studios. DCI’s primary purpose is to establish and document voluntary speciﬁcations for an open architecture for digital cinema that ensures a uniform and high level of technical performance, reliability and quality control. Note that the DCI speciﬁcation is not a standard. Standards for digital cinema are the domain of the Society of Motion Picture and Television Engineers (SMPTE). "DCI compliant" is a term used to describe products that conform to the DCI speciﬁcation. Products that have been tested per the DCI Compliance Test Plan (CTP) are posted at the DCI compliance web site. Notably, DCI compliance does not require compliance to the full set of SMP TE DCP standards. A copy of the most recent DCI speciﬁcation can be downloaded from the DCI website (h

ttp://dcimovies.com).

R5906847 DP2K SLP SERIES 02/06/2017 75

Page 80

7. ICMP

7.12 ICMP conﬁguration via Communicator

About ICMP conﬁguration

Following parameters are available to conﬁ gure the ICMP:

• Global settings: allows deﬁning name of the ICMP, host name (network identiﬁer) and IP address which can be used for communication with external content devices.

• User settings: deﬁnition of all users allowed on the ICMP.

• Server settings: deﬁnition of access to servers and storage libraries of content (movies, KDM, etc.).

• Player settings: Audio delay and audio output frequency.

• Audio channel: allows deﬁning the mapping of audio channels (content) on each audio output (AES outputs of the ICMP).

• Scheduler setting: Enable/Disable scheduler at startup, delays allowed in s cheduler mode and length of schedule history.

• Devices: allows deﬁning communication ports settings, to access external devices controlled by the automation.

• Automation Cues: event c ues that are triggered from different sources and to which can be assigned actions to be executed by the automation engine.

• Verify internal c lock of the ICMP.

All installation and maintenance operations on the ICMP are performed via Communicator, the Barco conﬁguration software. Please refer to the Com m unicator user guide for further information.

About Default settings

The restore of factory setting is a feature that allows removing all settings performed o n the ICMP and replaces them with the default values set at the factory. Please refer to the Communicator user guide for further information.

About the ICMP internal clock

The crystal on the ICMP board that manages the clock shows a certain drift (all crystals do). With the Communicator the internal clock can be adjusted. This maintenance action should be repeated every 3 month s. When neglected the system will locks up.

From ICMP software version 1.2.1 onwards it is possible to enable NTP (Network Time Protocol). You have to conﬁgure (at installation) an IP address where the ICMP can ﬁnd a sync signal. From then on, and as long as the connection is active, the ICMP will automatically k eep its clock correct. For detailed instructions see user guide of the Communicator.

R5906847 DP2K SLP SERIES 02/06/2017

Page 81

7.13 ICMP reset

This procedure requires that ICMP version 1.2.4 or later is installed.

ICMP reset possibilities

• The Star button on the local keypad (Not for C- and B-series)

• The ICMP reset button in the GUI of the Communicator.

• The ICMP reset button in the G UI of the Commander.

• The ICMP reset button in the GU I of the Web Commander.

• The ICMP hardware reset button located on the front panel of the ICMP (Not recommended, use only when all other re possibilities are exhausted!)

How to reset the ICMP?

1. Click on the ICMP reset button in the GUI of the Web Commander

Or, Click on the ICMP reset b utton in the GUI of the Commander

Note: It can be that the Commander or WEB-Commander is not able to send the reset command.

Or, click on the ICMP reset button in the GUI of the Communicator (recommended) Or, press the Star button on the local keypad for a few seconds (Not for C- and B-series)

As a result the projector is safely prepa red for the ICMP reboot. All ongoing events on the ICMP (e.g. ingest) are requested to end. After a few seconds the ICMP is requested to restart. The READY LED on the front panel of the ICMP starts to blink orange.

In c ase the ICMP is installed in DP4K-L series projector the lasers are switched off an d the projector remains in the same mode (e.g. Conditioned). The Star button on the local keypad s tarts blinking green. After the reset of the ICMP the lasers are s witched on again.

Once the READY LED lit continuous green the ICMP is up and running.

2. Did the reset of the ICMP fail?

If yes, perform a hardware reset as follows:

a) switch off the lasers of the projector or switch of the projector lamp.

b) press the ICMP hardware reset button a few seconds (reference 3 image 7-13) .

Warning: Resetting the ICMP with the hardware reset button may cause damage to the content on the HDDs. A re-conﬁgu-

ration of the whole system may be required!

As a re sult the projector is s afely prepared for the ICMP reboot. All ongoing events on the ICMP (e.g. ingest) are stopped immediately and the ICMP restarts.

7. ICMP

set

Image 7-13

WARNING: Resetting t he ICMP with the hardware reset button m ay cause damage to the content on the HDDs.

A re-conﬁguration of the whole system may be requ

R5906847 DP2K SLP SERIES 02/06/2017 77

ired!

Page 82

7. ICMP

7.14 Obtaining the Barco ICMP certiﬁcate

Necessary tools

Smartphone (with au to-focus) or control software (e.g. Communicator, Commander or WEB Commander)

Using the CertID label to download the ICMP certiﬁcate

1. S can the QR code (reference 1) on the front face of the ICMP with a smartphone. It’s recommended to use a smartphone with

auto-focus. The QR reader will automatically redirect to the ICMP cer tiﬁcate download page on the web server.

Note: Instead of downloading the ICMP certiﬁcate you can use the CertID number (reference 2), located below the QR code,

in communication with y our KDM supplier. Certiﬁed KDM suppliers can use this CertID number to retrieve the ICMP certiﬁcate directly.

96 92 35 86 40

Image 7-14

Using control software to obtain the ICMP certiﬁcate

1. U se the WEB Commander to download the ICMP certiﬁcate from the ICM P main board. For detailed instructions see user guide

of the WEB Commander. Or, use the Commander to download the ICMP certiﬁcate from the ICMP main board. For detailed instructions see user guide of the Commander. Or, use the Communicator to download the IC MP certiﬁcate from the ICMP main board. For detailed instructions see user guide of the Comm unicator.

R5906847 DP2K SLP SERIES 02/06/2017

Page 83

7.15 Removing a HDD from the ICMP

In case the ICMP has to be returned to factory (e.g. for repair) the non defective HDDs should be removed an d kept.

How to remove a HDD ?

1. S w itch off the projector.

2. M oving the latch towards the left.

Image 7-15

3. P ush the unlock button to open the handle.

7. ICMP

Image 7-16

4. P ull the HDD out of its slot.

Image 7-17

To install the HDD see procedure "Installing a HDD into the ICMP", page 80.

R5906847 DP2K SLP SERIES 02/06/2017 79

Page 84

7. ICMP

7.16 Installing a HDD into the ICMP

This procedure assumes that the HDD slot of the ICMP is empty. If not, see procedure "Removing a HDD from the ICMP", pag e 79.

CAUTION: Always use a new empty spare part HDD from Barco to replace a malfunction HDD. Do not use a

HDD from another ICMP HDD set.

CAUTION: Always make sure that all HDDs in the ICMP HDD set have the sam e storage capacity. See label

on top of the HDD to know the storage capacity.

How to install a HDD ?

1. E nsure that the projector is s witched off.

2. P repare the HDD for insertion b y moving the latch towards the left and push the unlock button to open the handle.

Image 7-18

3. Insert the HDD into the HDD slot. Ensure that the handle is sufﬁciently open so that the hook (reference 1) of the handle can

pass the front plate of the ICMP.

Image 7-19

4. P ush the HDD completely and ﬁrmly inside its slot, c lose the handle, and move the latch towards the right.

R5906847 DP2K SLP SERIES 02/06/2017

Page 85

Image 7-20

5. S w itch on the projector.

In case you replace one HDD (e.g. degraded mode) the ICMP automatically starts with the RAID recovery process. The red LED of the HDD which has to be rebuilt is blinking. This process takes about 200 GB per hour. Once the RA ID is completed the red LED turns off.

CAUTION: It’s strongly recommended to complete the RAID recovery process prior to starting a show. This

to ensure that the content integrity is preserved and that the show is not interrupted.

7. ICMP

R5906847 DP2K SLP SERIES 02/06/2017 81

Page 86

7. ICMP

82 R5906847 DP2K SLP SERIES 02/06/2017

Page 87

8. Communicator Touch Panel

8. COMMUNICATOR TOUCH PANEL

About this chapter

This chapter gives a short introduction of the Communicator Touch Panel, describes how to install the Communicator Touch Panel interface onto the top of y our DP2K SLP-series and how to connect the interface. For operation instructions refer to the user guide of the Communicator software. The latest software version and updated user guide for the Communicator can be downloaded from

ttps://www.barco.com.

The Communicator Touch Panel is not included in the package of the projector. An alternative for the Communicator Touch Panel is the use of the Communicator for PC (Mac, Linux or Windows).

Overview

• Communicator Touch Panel

• Installing the Touch P anel interface

• Repositioning the Touch Panel interface

R5906847 DP2K SLP SERIES 02/06/2017

Page 88

8. Communicator Touch Panel

8.1 Communicator Touch Panel

Communicator Touch Panel for digital cinema projectors

The Communicator Touch Panel is designed for multi-user command and control. The Communicator enables users to learn quickly and operate efﬁciently - using an elegant and ﬂexible Touch Panel interface. The interface’s commonality means that operators can intuitively use any model in the produ ct line, without restriction, and its user-friendly nature translates directly into a short and enjoyable learning curve.

Image 8-1

Flexible Touch Panel interface

The Touch Panel interface can be mounted upon a swivel arm whic h easily ﬁts on top of the DP2K SLP -series. One central locking mechanism of the swivel arm allows instant ﬁxation of the Touch Panel interface in any position.

The Touch Panel interface can also be installed further away from the DP2K SLP -series. For this purpose an Ethernet cable up to 50 m eter can be used to realize a direct data communic ation between the DP2K SLP-series and the Communicator Touch Panel.

The Touch Panel interface can also be connected via a Local Area Network (LAN) in the same way as the DP2K S LP-series. In this conﬁguration both devices can communicate w ith each other as well.

The Touch Panel interface requires a voltage supply +12 VDC and 1,5 ampere. Note that the DP2K SLP-series has a 12 VDC output which can be used to power up the Touch Panel interface. Nevertheless, the use of a separate +12 V DC adaptor (1,5 ampere minimum) is required in case the Touch Panel interface is installed more then a few meters away from the DP2K SLP-series.

Parts location of the Tou ch Panel interface

3 4 5 6 7

Image 8-2 1 Touch screen 2 Communication panel 3 Knobtooperatecentralswivelclamp 4Baseofswivelarm 5 Power input 12 V DC, 1.5A 6 RS232 port (sub-D) 7 Ethernet port (RJ45)

84 R5906847 DP2K SLP SERIES 02/06/2017

Page 89

Touch Panel power/data customized cable

Image 8-3 Customized cable to connect Touch Panel interface with the Barco projector.

The Communicator Tou ch Panel has its own user g uide which latest version is available on the Barco website.

8. Communicator Touch Panel

R5906847 DP2K SLP SERIES 02/06/2017 85

Page 90

8. Communicator Touch Panel

8.2 Installing the Touch Panel interface

Necessary tools

• open-end wrench 17 mm

• open-end wrench 10 mm

How to install the Touch Panel interface onto the top of the projector?

1. A ss emble the mounting plate and the swivel arm together as illustrated. First place the nut (reference 1 image 8-4) upon the

rod of the mounting plate, then add the lock washer (reference 2 image 8-4), then fasten the mounting plate a together. When the arm is mounted, turn the nut (reference 1 image 8-4) against the arm to secure the position.

Image 8-4

2. S lide a washer (reference 4 image 8-5) over the base of the swivel arm (reference 3 image 8-5) and insert the base of the swivel

arm into one of the four possible mounting holes (reference 1 & 2 image 8-5) at the top of the projector.

Note: Wh ich mounting hole t o use depends on the operator preferences. In the illustration below the swivel arm is installed

into the mounting hole nearest by the Local Keypad of the projector.

Caution: If you choose to use the back mounting holes (reference 1 image 8-5) to mount your Touch Panel, ensure it is sufﬁ -

ciently removed from the hot top exhaust system, to avoid damage.

nd the swivel arm

Image 8-5

3. P lace the Touch Panel interface upon the mounting plate of the swivel arm and fasten the two wing nuts (reference 5 image 8-6)

as illustrated.

R5906847 DP2K SLP SERIES 02/06/2017

Page 91

8. Communicator Touch Panel

Image 8-6

4. C onnect the DC plug, the RJ45 Ethernet plug and the D-SUB plug of the customized cable into t

Touch Panel interface.

heir respective sockets on t he

Image 8-7

5. Connect the circular plug of the customized cable with the circular socket (reference 6 image 8-8) at the right s ide of the L ocal

Keypad of the projector.

Caution: To avoid connector damage, align the pins before you connect the customized cable.

Note: Ensure to tighten the locking nut on the connec tor.

Image 8-8

6. A ttach the multi cable to the swivel arm using the two Velcro strips.

7. P osition the Touch Panel interface in the desired location. See "Repositioning the Touch Panel interface", page 88.

R5906847 DP2K SLP SERIES 02/06/2017

Page 92

8. Communicator Touch Panel

8.3 Repositioning the Touch Panel interface

How to reposition the Touch Panel interface?

1. Hold the Touch Panel interface with one hand .

2. Release the central swivel clamp by turning the knob (reference 7 image 8-9) counterclockwise.

Image 8-9

3. M ove the Touch Panel interface to the desired position.

4. F asten the central swivel clamp by turning the knob clockwise.

CAUTION: Never release the central swivel lock without supporting the Touch Panel interface.

88 R5906847 DP2K SLP SERIES 02/06/2017

Page 93

9. Starting up

9. STARTING UP

About this chapter

This chapter contains the switch ON and switch OFF procedures of your DP2K SLP-series. These procedures highlight all important points to be checked prior to switching the projector ON. This is to ensure a safe startup of the projector.

Overview

• Switching the DP2K SLP-series ON

• Switching the DP2K SLP-series OFF

R5906847 DP2K SLP SERIES 02/06/2017

Page 94

9. Starting up

9.1 Switching the DP2K SLP-series ON

How to switch on?

1. E nsure that the DP2K SLP-series is installed onto a stable platform.

2. E nsur e the projector is correctly connected to the mains power.

3. E nsur e that the correct lens is installed for your application.

4. Check if a video source is connected to the projector.

5. P ress the Power Switch to switch the projector ON. As a result the projector starts up and the communicator touch panel starts

its initialization procedure.

Note: The projector always boots up in the same mode (E.g. Standby or Sleep) as it was switched off. T his procedure assumes

that the projector was switched off in standby mode (projector fully operational but light source is off).

6. Wait until the status light of the projector lights up GREEN (not ﬂas hing).

7. P ress the STANDBY button on the Local Keypad or use the Communicator to activate the light source.

8. P ress the DOWSER button on the Local Keypad or use the Communicator to open the dowser.

DOWSER

Image 9-1

How to awake the projector from Sleep mode?

1. P ress the SLEEP button on the Local Keypad for three seconds or use the Communicator to put the projector in S tandby mode.

As a result the projector starts booting and initializing all electronics. D uring the booting and initializing phase the backlight color of the Sleep button is purple (transition phase). Once the projector is fully awake the backlight color of the Sleep button is green.

Note: When the projector is in Sleep m ode only the bac klight of the Sleep button lights up red. The backlight of all other buttons

of the Local Keypad remains off.

The backlight color of the Sleep button, Standby button up green to project the image of the applied source.

, Dowser button and Test Pattern button must all light

CAUTION: See user’s guide of the Communicator Touch Panel to operate and control the DP2K SLP-series.

When for any reason a restart of the p rojector is required, the content server should be restarted also.

90 R5906847 DP2K SLP SERIES 02/06/2017

Page 95

9. Starting up

9.2 Switching the DP2K SLP-series OFF

HowtoswitchtheDP2KSLP-seriesOFF?

1. P ress the Standby button on the Local Keypad or use the Communicator Touch Panel to switch the projector from Light Source

ON mode to S tandby mode. As a result the light source turns off while the fans keep turning to cool down the projector.

2. A llow the projector to cool down for 5 minutes minimum or until the speed of t he fans decreases.

3. S w itch the projector OFF with the power switch.

Tip: Make sure no lens m otors are running while switching off the projector. Wait for lens positioning to com ple

5min

Image 9-2

How to put the projector into Sleep mode?

1. Check if the light source is switched off. If not, press the Standby button on the Local Keypad or use the Communicator to switch

the light sou rce off. The backlight color of the Standby button is red when the light source is switched off.

Note: To put the projector into Sleep the projector must be in Standby mode (in other words the lam p must be off). If the lamp

is ignited he Sleep button is disabled notwithstanding the backlight color of the Sleep button is green.

2. P ress the SLEEP button on the Local Keypad for three seconds or use the Communicator to put the projector into Sleep mode.

As a result the projector immed iately shuts down the electronics. When the a fter cooling cycle of the light source is ﬁnished, the projector will go to sleep. The backlight color of the Sleep button is red in Sleep m ode even when the projector is ﬁnishing the after cooling cycle.

Note: Pressing the Sleep button before th e after cooling cycle has ﬁnished, will restart the projector in a normal way.

te.

R5906847 DP2K SLP SERIES 02/06/2017

Page 96

9. Starting up

92 R5906847 DP2K SLP SERIES 02/06/2017

Page 97

10. Scheimpflug

10. SCHEIMPFLUG

About this chapter

This chapter explains the Scheim pﬂ ug principle and whe n to apply S cheimpﬂ ug correction upon y our DP2K SLP-series. In addition to the procedure for Scheimpﬂug adjustment the procedure to adjust the Back Focal Length is also included in this chapter.

Scheimpﬂug principle

The " plane of sharp focus" can be changed so that any plane can be brought into sharp focus. When the DMD plane and lens plane are parallel, the plane of sharp focus will also be parallel to these two planes. If, however, the lens plane is tilted with respect to the D MD plane, the plane of sharp focus will also be tilted according to geometrical and optical properties. The DMD plane, the principal lens plane and the sharp focus plane will intersect in a line below the projector for downward lens tilt.

Overview

• Scheimpﬂug introduction

• Scheimpﬂug adjustment

• Fixation of the Lens Holder front plate

• Back Focal Length adjustment

R5906847 DP2K SLP SERIES 02/06/2017

Page 98

10. Scheimpflug

10.1 Scheimpﬂug introduction

What is Scheimpﬂug?

The lens holder has to be adjusted so that the “sharp focus plane” of the projected image falls together with the plane of the screen (Fp1→Fp2). This is achieved by changing the distance between the DMD plane and the lens plane (Lp1→Lp2). The closer the lens plane comes to the DMD plane the further the sharp focus plane will be. It can occur that you won’t be able to get a complete focused image on the screen due to a tilt (or swing) of the lens plane with respect to the DMD plane. T his is also known as Scheimpﬂug’s law. To solve this the lens plane must be placed parallel with the DM D plane. This can be achieved by turning the lens holder to remove the tilt (or swing) between lens plane and DMD plane ( Lp3→Lp4).

Lp1

Lp2

DMD

Image 10-1 Scheimpﬂug principle

SCREEN

Fp1

Fp2

DMD

Lp3 Lp4

(Scheimpflug)

Fp4

Fp3

SCREEN

Scheimpﬂug principle

Scheimpﬂug adjustment points

The front plate of the Lens holder is equipped with four bronze (Scheimpﬂug) nuts and four set screws with lock nut. These screws and nuts are used for Scheimpﬂug adjustment.

Image 10-2 1Scheimpﬂug adjustment nuts No1: Inﬂuences the sharp focus plane in the lower left corner of the projected image. 2Scheimpﬂug adjustment nuts No2: Inﬂuences the sharp focus plane in the lower right corner of the projected image. 3Scheimpﬂug adjustment nuts No3: Inﬂuences the sharp focus plane in the upper right corner of the projected image. 4Scheimpﬂug nut No 4: wi thout adjustment functionality. 11 Set screw for nut No1. 12 Set screw for nut No2. 13 Set screw for nut No3. 14 Set screw for nut No4. 21 Lock nut. 22 Lock nut. 23 Lock nut. 24 Lock nut.

Reference 1, 2 and 3 are adjustment points. Reference 4 is a locking point and N OT used during Scheimpﬂug adjustment.

94 R5906847 DP2K SLP SERIES 02/06/2017

Page 99

10. Scheimpflug

When to apply Scheimpﬂug?

Only apply a Scheimpﬂug correction in case the overall focus of the pr ojected image is not equally sharp (can be caused if the projector is NOT in parallel with the screen or a previous misaligned Scheimpﬂug) . Take into account that the consequence of applying Scheimpﬂug correction upon a screen not in parallel with the projector is that the projected image differs from the rectangle shaped image. In other words “distortion” of the projected image occurs. Masking will be required to solve the distortion.

The disadvantage of Masking is loss of content. Therefore it is strongly recommended to place the projector in parallel with the projection screen and use the SHIFT functionality of the Lens Holder to m atch the projected image with the projection screen. In case the S HIFT range is not sufﬁcient then the projector can be tilted and Scheimp ﬂug can be applied.

R5906847 DP2K SLP SERIES 02/06/2017

Page 100

10. Scheimpflug

10.2 Scheimpﬂug adjustment

Necessary tools

• 3mm Allen wrench.

• 13mm nut driver.

• 10mm nut driver.

Preparation steps:

1. E nsur e that the throw ratio of the ins talled lens matches the requirements of the application (projection distance a nd screen size).

2. E nsure that the correct lens parameters are activated. (See user guide of the Communicator chapter Installation > Advanced >

Lens parameters)

Note: Selecting the wrong lens parameters will result in an unexpected behavior of the lens when using macros for switching

between FLAT and S CO PE (change in picture size and focus).

3. P erform a lens H OME & RETURN operation. (See user guide of the Communicator chapter Installation > Advanced > Lens

parameters)

4. P roject the green focus test pattern.

Image 10-3

5. Z oom the lens for maximum image on the screen (WIDE).

6. Is it possible to focus the center of the projected image?

If yes, the Back Focal Length is O K. Proceed with the next step. If no, the Back Focal Length needs realignm ent. Proceed with the procedure "Back Focal Length adjustment", page 100.

7. Unlock and turn out the 4 set screws (reference 11 im age 10-4) of the Lens Holder by 1 centimeter. Use a 10mm nut driver for

the lock nuts (reference 21 im age 10-4) and use a 3mm Allen wrench for the set sc rews.

1121

Image 10-4

8. F ully loosen the Scheimpﬂug nut at the lower left of the Lens Holder (reference 4 image 10-5). Use a 13mm nut driver.

9. O ptimize the focus of the projected image in the center of the screen (F) using the motorized focus control (Lo cal Keypad).

FOCUS

Image 10-5

96 R5906847 DP2K SLP SERIES 02/06/2017

Barco DP2K-10SLP, DP2K-8SLP User And Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual