Barco B-16 Mobile LED Installation Manual

B-16 Mobile LED

Installation manual

R9855516

R59770490/00
07/01/2010

Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Visit us at the web: www.barco.com

Printed in Belgium

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war­ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.

Copyright ©

All rights reserved. No part of this document m ay be copied, reproduced or translated. It shall not other
stored in a retrieval system without the prior written consent of Barco.

wise be recorded, transmitted or

Trademarks

Brand and product names m entioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as commen ts or examples and are not to be understood as advertising for
the products or their manufacturers.

Guarantee and Compensation

Barco provides a guarantee relating to p erfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of c omm issioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems a re commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the pu
system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guara ntee provided by Barco either.

The environmental conditions as well as the servicing and m aintenance regulations specified in the this manual must be complied with by
the customer.

rchaser will be rendered invalid. Not included in the guarantee cove rage are

Table of contents

TABLE OF CONTENTS

1. Safety................................................................................................................ 3

1.1 General instructions ................................................................................................................. 4

1.2 Important Safety instructions ........................................................................................................ 5

1.3 Safety instructions for LED screen setup........................................................................................... 6

1.4 Safety instructionwhen driving the trailer........................................................................................... 7

1.5 Important Warnings. ................................................................................................................. 8

1.6 Proper usage of the LED wall ....................................................................................................... 9

1.7 Specific warnings for diesel-fueled generator . .. ...................................................................................10

2. System overview ..................................................................................................11

2.1 Introduction .......................................................................................................................... 12

2.2 B-16 Mobile LED trailer.............................................................................................................. 13

2.3 B-16 Mobile LED tiles ...............................................................................................................14

2.4 LED-Pro, video processor unit ......................................................................................................15

2.5 B-16 Mobile LED generator ......................................................................................................... 17

3. Installation..........................................................................................................19

3.1 Location of accessories .............................................................................................................20

3.2 Mechanical setup of trailer . .........................................................................................................21

3.3 Powering the B-16 Mobile LED .....................................................................................................24

3.4 Lifting the first part...................................................................................................................27

3.5 Assembling first parton second part................................................................................................29

3.6 Assembling third part on the first two ...............................................................................................31

3.7 Position screenout of the trailer ....................................................................................................32

4. Moving down the display ... ................ ................ .................. ................ ................ ...35

4.1 Disassembling the lower part .......................................................................................................36

4.2 Disassembling the middlepart......................................................................................................39

4.3 Move down the last part............................................................................................................. 41

4.4 Stop generator ....................................................................................................................... 42

4.5 Preparing for departure..............................................................................................................43

5. Maintenance, Service.............................................................................................45

5.1 Service and maintenance table . . ...................................................................................................46

5.2 Service and Maintenance of the Generator ........................................................................................48

A. Wind speeds.............. ................ ................ ................ ................ ................ ...........55

A.1 Wind speeds table . . .................................................................................................................57

B. Dimensions ..........................................................................................................59

B.1 Dimensions of a B-16 Mobile LED..................................................................................................61

B.2 Specificationof trailer................................................................................................................62

B.3 Tile specifications....................................................................................................................63

R59770490 B-16 MOBILE LED 07/01/2010

1

Table of contents

2 R59770490 B-16 MOBILE LED 07/01/2010

1. SAFETY

Overview

• General instructions

• Important Safety instructions

• Safety instructions for LED screen setup

• Safety instruction when driving the trailer

• Important Warnings

• Proper usage of the LE D wall

•Specific warnings for dies el-fueled generator

1. Safety

R59770490 B-16 MOBILE LED 07/01/2010

3

1. Safety

1.1 General instructions

Caution

Setup of the B-16 Mobile LED should be performed only a fter you are thoroughly familiar with all of the proper safety checks and
setup instructions. To do otherwise increases the risk of hazards and injury to the user.

Do not modify and/or replicate any component. Barco uses specific materials and man ufacturing processes in orde r to achieve
mechanical strength of the trailer and hydraulic mast. Consult Barco for assistance with custom applications.

Always follow Barco’s setup instructions. Contact Barco if you should have any question re garding the sa

The manufacturer assumes no liability for incorrect, inadequate, irresponsible or unsafe use of systems.

Product care

Barco products must be used in a manner consistent with their design and inspected on a routine basis for security, wear, deforma­tion, corrosion and any other circumstances that may affect the proper working of the B-16 Mobile LED.

Barco recommends inspections at regular intervals for the B-16 Mobile LED. If a part of the B-16 Mobile LED is found to have
damage, it must be removed for service or replaced immediately.

Under no circumstances are Barco parts repairable by anyone other than Barco.

Owner’s record

The part number and serial number are p rinted on labels which are stuck on the respective parts. Record these numbers in the
spaces provided below. Refer to them whenever you call upon your Barco custom service engineer re garding this product.

Name Part number Serial number Supplier

fety of an application.

4 R59770490 B-16 MOBILE LED 07/01/2010

1.2 Important Safety instructions

Instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• IMPORTANT, plug holder clamps must be locked firmly on all controller units and power boxes to prevent the possible ingress
of fluids or solid particles. Replace damaged clamps immediately.

• Clean only with materials or chemicals that are inert, nonabrasive, n oncorrosive and non-marking. Consult t h
for further advice should any doubts exist regarding any cleaning procedure.

• Do not block ventilation openings. Install in accordance with the manufacturers instructions.

• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets / plugs are dam aged
then replacement of the defective parts m ust be undertaken immediately.

• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, an d the point
where they exit from the apparatus. Replace damaged power/data cords im mediately.

• Only use attachments/accessories specified by the manufacturer.

• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this
apparatus when unused for a long period of time.

• Refer all servicing to qualified service technicians/personnel. Servicing is required w hen the B-16 Mobile LED has been dam­aged in any way, such as hydraulic mast or generator is damaged, the B-16 Mobile LED does not operate normally.

• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use caution during transporting
to av oid damage by possible tipping.

• Do not make use of the B- 16 Mobile LED to climb on the display.

• Do not place a ladder against t he display to access the tiles or for other purposes.

• Do not move the trailer when the B-16 Mobile LE D display is in the air.

• Do not walk on the roof of the trailer as it has not been designed and reinforced for this purpose.

e m anufacturer

1. Safety

R59770490 B-16 MOBILE LED 07/01/2010

5

1. Safety

1.3 Safety instructions for LED screen setup

Overview

• Only trained people are allowed to set up the LED screen

• No people are allowed around or in the trailer during the setup process of the LED Sc reen.

• Always put the trailer legs out before lifting the screen.

• Always lock the turntable.

• Always us e mechanical locks to lock the turntable.

• Maximum wind force = 7 Beaufort. When the wind force is higher than the maximum allowed wind force, bring the screen down
See "Wind speeds", page 55 for an overview of the relation between Beaufort, km /h, miles/h and m/s.

• Always place the safety pins in the mast.

6

R59770490 B-16 MOBILE LED 07/01/2010

1.4 Safety instruction when driving the trailer

Overview

• Always stick to the local trafficrules.

• Always respect the local m otor vehicle inspection for trailer and car.

• Set draw-bar till trailer level.

• Tires pressure: 4,5 bar

• Max weight under coupling: 150 kg

• Maximum driving speed is 90 km/h. Slow down in the bends.

1. Safety

R59770490 B-16 MOBILE LED 07/01/2010

7

1. Safety

1.5 Important Warnings

Important warnings

• High leakage current:
The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of e lectric
shock due to high leakage current, p roper grounding of the installation is required.

• Flammable materials:
Keep flam m able materials away from the B-16 Mobile LED generator. A lot of energy is transferred into heat. The installation
should be such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation
must be provided.

• Mains cords:
The power cords delivered with this system have special properties for safety. T hey are not user serviceable. If the power cords
are damaged, replace only w ith new ones. Never try to repair a power cord.

• Maximum and minimum ambient temperature:
The maximum ambient temperature for the LED wall is 50 °C, the minimum tem perature is -35 °C.

• Risk of electric shock:
Do not open LED tile doors. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts
inside. Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

Image 1-1

• This equipment MUST be earthed:
In order to protect against risk of electric shock, the installation should
grounding will expose you to the risk of electric shock.

• Data cables:
The data cables provided with this system have spec ial properties for safety. They are not user serviceable. If the data cables
are damaged, replace them only with new ones. Never try to repair a data cable. Avoid exposure of data cables to accidental
contact with lightning or power conductors.

be properly grounded. Defeating the purpose of the

8

R59770490 B-16 MOBILE LED 07/01/2010

1.6 Proper usage of the LED wall

Proper usage of T-series tiles

• No part of the T-series tile may come in contact with any type of abrasive.

• No part of the T-series tile may come in contact with an y type of corrosive substance.

• T-series tiles are to be used in environments meeting the operating specifications.

• T-series tiles are not to be exposed to extreme localized heat or cold exceeding the tem perature specifications.

• T-series tiles are not to be exposed to any element or situation that will cause any part of the display to heat beyond what occurs
during normal operation. Such situations include but are not limited to lasers, ultrasonic vibration, or any type of substance that
prevents proper ventilation and heat radiation of the T-series tiles.

• Power connected to the T-series tiles must meet the specifications outlined in the installation manual.

• No force can be applied to the LED’s. Any LED’s damaged due to m echanical stress are not covered by the warranty.

• Safety and functional features of the display cannot be defeated.

• It is not allowed to climb or hang any additional equipment on the back of a T-series wall. Nothing is to be allowed to hang from
the cables of a T -series tile.

• Any failures must be imm ediately and appropriately dealt with (equipment returned to Barco?). Failing equipment c
left t o r un in a wall.

• Only Barco cables specified to be used with the T-series display are to be used to connect components in a T-series w all.
Further, care must be t aken to connect signal only according to the installation m anual.

• T-series tiles are not to be connected to any non-Barco equipment.

• T-series tiles m ay be cleaned only in accordance to the procedures defined in the installation manual.

• The T-series tile is equipped with two high density air filters. These filters must be replac
the environment conditions of the tile. It is recommende d to replace the filters every 6 months.

ed on a regular basis, depending on

1. Safety

annot be

R59770490 B-16 MOBILE LED 07/01/2010

9

1. Safety

1.7 Specific warnings for diesel-fueled generator

Check before operating the engine

• If the engine is ma lfunctioning DO NOT oper ate until repairs are made.

• Be sure all guards and shields are in place before operating the engine. Replace any that are damaged or missing.

• DO NOT start the engine by shorting across starter terminals.

Handling of fuel and lubricants

• Always s top the engine before refueling or lubricating.

• DO NO T smoke or allow flames or sparks in your working area. Fuel is extremely fl ammable and explosive.

• Never store flammab le liquids in the engine compartment.

• Refuel at a well-ventilated and open place. If fuel or lubricants spill, clean up immediately and properly dispose of.

• DO NO T mix gasoline or alcohol with diesel fuel. The mixture can caus e a fire.

Fire prevention

•Toavoidafire, be alert for leaks of flammables from hoses and lines. Be sure to check for leaks from hos es and pipes, such
as fuel and hydraulic by following the maintenance check list.

•Toavoidafire, do not short across power cables and wires. Check to see that all power cables and wires are in good condition.
Keep all pow er connections clean. Bare wire or frayed insulation can cause a dan gerous electrical shock and personal injury.

Cautions against burns and battery explosion

• To avoid burns, be alert for hot components during operation and just after the e
muffler cover, rad iator, piping, engine body, coolants, engine oil, etc.

ngine has been shut off. Such as the muffler,

Conducting safety checks and maintenance

• Maintenance of the generator is only to be performed by a specialized service technician.

• When performing safety checks or engine service, be sure the engine is level and well suppo rted. Use approved stands de­signed for this type of service.

• Check or conduct maintenance after the engine, radiator, muffler, or muffler co

• When service is performed with two or more people present, take care to perform all work safely. Be aware of their location
especially when starting the engine.

ver has cooled off completely.

10

R59770490 B-16 MOBILE LED 07/01/2010

2. SYSTEM OVERVIEW

Overview

• Introduction

• B-16 Mobile LED trailer

• B-16 Mobile LED tiles

• LED-Pro, video processor unit

• B-16 Mobile LE D gener ator

2. System overview

R59770490 B-16 MOBILE LED 07/01/2010

11

2. System overview

2.1 Introduction

Overview

The B-16 Mobile LE D is a mobile outdoor LED display solution. The LED-wall comes in a trailer that can be pulled b y a vehicle with
a 3500 kg (7000 lbs) towing capacity. The bolted draw bar makes it possible to adapt only 3 different ball hitches 390/430/470 mm
(standard 430 mm). All electronics and setup equipm ent are stored properly and compact when traveling.

Image 2-1
B-16 Mobile LED

LED tiles used in the B-16 M obile LED are T16 tiles and t

When arriving on the event location, the B-16 Mobile LED can easily be set up. The wall itself slides out of the trailer by means of a
hydraulic system. There is no need for trusses and structures to be set up. The screen can be turned + 90° or - 90° out of its neutral
position, allowing you to adjust the display to face the audience.

The B-16 Mobile LED contains a diesel-fueled generator. No external power supply is required but can be used, and it comes with
a Ba rco LED-PRO for high quality im age processing.

The following topic enumerates all different compon ents of a B-16 M obile LED so lution and describe their
functionality in the system. FOR MORE DETAILED INFORMATION ON THESE COMPONENTS PL EAS E REF E R
TO THEIR RESPECTIVE USER MANUAL.

ypically designed for outdoor use.

12 R59770490 B-16 MOBILE LED 07/01/2010

2. System overview

2.2 B-16MobileLEDtrailer

Overview

The trailer is equipped with a parking jack and 4 bearings to level the trailer.

It also contains a hydraulic mast to s et up the LED screen and a LED screen split up in 3 parts.

A diesel generator from Europower creates the necessary electrical power for the LED system and for the peripheral equipment if
no external power source is connected to the trailer.

Storage locations are provided for the setup tools (drill machine, support plates for the outriggers, handles to open or close the
interconnection between tiles, grounding cable and pin, battery startup cable, etc.). The trailer also contains an anti-theft clamp for
a wheel.

R59770490 B-16 MOBILE LED 07/01/2010

13

2. System overview

2.3 B-16 Mobile LED tiles

Overview

The B-16 Mobile LED is equipped with T-16 series LED tiles. A ll tiles are c onnected in series via a data path. Each tile picks out a
part of the video information of the data s tream on the data path and processes this information for displaying on its LEDs.

Barco uses special designed outdoor sockets for power and data connections from tile to tile and to other peripherals. These rugged
sockets are watertight (IP65) when used with the appropriate plugs and sealing rings . Each socket is equipped with a plug holder
clamp which, when locked, ensures the plug is completely pressed into the socket.

E

A

B

Image 2-2
A Power output port.
B Power input port.
C Data output port.
D Data input port.
E Plug holder clamp.

C

D

Specifications

Calibrated Brightness

Certifications UL/ETL, CE, FCC Class A, RoHS, CCC, CETL

Colors

Contrast ratio

Hor. viewing angle

Humidity

LED configuration 1R, 1G, 1 B

Pixel density

Pixel pitch 16 mm

Power consum ption maximum: 400W/m2

Processing 16-bit/color

Refresh rate 800 Hz

Ruggedness front: IP65

Serviceability Back access

Temperature range operating: -35°C to 50°C (-31°F to 122°F)

Tile dimensions 0.96m x 0.96m x 0.25m

Vert. viewing angle –40° (from below)

Weight / Tile 48 kg/tile (106 lbs)

6,000 NIT

281 trillion

7,000:1

110° (min 50% brightness)

operating: 10% to 99%

storage: 10% to 99%

3,906/sqm - 363/sqf

3,600/tile (60x60)

minimum: 120W/m2

back: IP 54

storage: -35 to 50°C (-31°F to 122°F)

> +15° (from above)

> ( min 50% brightness)

14 R59770490 B-16 MOBILE LED 07/01/2010

2. System overview

2.4 LED-Pro, video processor unit

Functionality overview

The Barco LED-PROTMis a powerful all-in-one signal processor that accepts a wide range of video input signals and processes
them to drive the B-16 Mobile LED display. The LED-PRO
while still maintaining a high quality picture. The unit is a high performance digital video scaler, scan converter, standards conv erter,
switcher and transcoder in one.

The LED-PRO

TM

has an advanced feature set that includes:

• universal inputs

• aspect ratio conversion

• memory presets

• test patterns

• Lock to Source

• picture ad justments

• motion adaptive de-interlacing

• 3:2 and 2:2 pull down detection

TM

allows you to scale visual s ources, mix and match them in any way

Image 2-3
LED-PRo

The LED-PRo is built-in in a control center at the right side behind the back door.

Image 2-4
Control center

R59770490 B-16 MOBILE LED 07/01/2010 15

2. System overview

Features overview

• Three universal inputs accept RGBHV/RGBCs/RGsB computer video, component video (STD or HDTV), SVideo, or composite
video with loop-through

• SD SDI/HD-SDI input.

• DVI-I connectors support both universal analog and DVI input with loop-through.

• DVI output connector for Barco LED Display interface.

• Input Video detection and Auto-acquisition. LE D-P RO
configurations.

• Aspect r atio conversion and adjustments

• Pan and zoom

• Freeze

• 10-Bit processing

• De-interlacing modes: Motion Adaptive and Field to Frame

• 3:2 pulldown detection for NTSC and 2:2 film detection for PAL video sources

• Decodes NTSC, PAL, and SECAM

• Ethernet connec tor for real-time control

• Vertical lock (Lock to Source) eliminates image tears and other artifacts in s caled motion video by eliminating frame rate co n­version

• 64 independ ent input configuration memory presets

• Motion ad aptive de-interlacing for HDTV inputs

• Low Video Delay

TM

will auto detect and match input video to stored formats or user

16

R59770490 B-16 MOBILE LED 07/01/2010

2. System overview

2.5 B-16 Mobile LED generator

Overview

The Europower generator contains super-silenced generating sets with a Kubota water-cooled diesel engine.

For more detailed information about the Europower generator, consult the manual of the diesel engine and alternator delivered with
each generating set.

The chassis of the generator serves as fuel tank and contains the fuel filter cap, the mechanical fuel level meter, the fuel drain cap,
the battery support and the fixing support of t he oil drain pum p.

The whole is mounted on 4 anti vibration engine suspensions to prevent vibrations to be transferred to the trailer and permit a more
comfortable use of the machinery.

Image 2-5
Europower generator

Fuel

Always use diesel.

Image 2-6
Fuel inlet and indication

1 Fuel inlet
2 Fuel meter

R59770490 B-16 MOBILE LED 07/01/2010 17

2. System overview

18 R59770490 B-16 MOBILE LED 07/01/2010

3. INSTALLATION

WARNING: Never setup the display when the wind force is 7 beaufort o r higher.

CAUTION: Never use the mast without security pins !

Overview

• Location o f accessories

• Mechanical setup of trailer

• Powering the B-16 Mobile LED

• Lifting the first part

• Assembling first part on se cond part

• Assembling third part on the firs t tw o

• Position screen out of the trailer

3. Installation

R59770490 B-16 MOBILE LED 07/01/2010

19

3. Installation

3.1 Location of accessories

Overview

Next to the back door some handy tools are m ounted to the wall.

Image 3-1
Tool s

1 Tile lock key

2Waterlevel

3

Grounding pin and wire

4 Four-way wrench

5

Wooden support block for outriggers

6 Drill machine

20

R59770490 B-16 MOBILE LED 07/01/2010

3. Installation

3.2 Mechanical setup of trailer

What should be done ?

The trailer must be placed on a stable underground. Then the trailer must be uncoupled from the pulling vehicle and water-levelled
in both directions.

How to uncouple

1. P lace the trailer on a flat and hard ground (min 2 kg/cm²)

2. Turn down the draw bar support until it reaches the ground.

Use the drill machine with nut driver to lower the support.

3. Trigger the brake system of the trailer.

Image 3-2
Brake system trailer

1 B rake handle

4. Uncouple the trailer from the vehicle hitch.

Trailer setup

1. Release the handles under the trailer and pull out the outriggers (L

Image 3-3
Unlock outriggers

1 Unlock handle
2 Outrigger

2. P lace a wooden support under eac h outrigger (4 sides).

eft side).

R59770490 B-16 MOBILE LED 07/01/2010

21

3. Installation

Wooden supports are mounted next to the back entrance door.

Image 3-4
Location and mounting of wooden support blocks

3 Location wooden support blocks
4 Mounted wooden support blocks

3. B ring down the 4 outriggers.

Use the drill machine with nut driver and/or the delivered manual nut driver to lower the outriggers and mak e sure that the wheels
are not o n the ground anymore.

Image 3-5
Outtrigger lowing points

5 Lowering points left side
6 Lowering points righ

t side (behind cover plate)

Note: If they cannot reach the ground, place extra wooden plates.

4. L evel the B-16 Mobile LE D in width and length direction. Use a level.

Start at the ba ck side with the width direction. Level by turning out the left or right outrigger Use the manual nut driver instead of
the drill machine.
Continue with the length direction.
When finished, check the width and length direction and repeat the procedure if necessary.

22

R59770490 B-16 MOBILE LED 07/01/2010

Image 3-6
Water level trailer

5. Turn up the draw bar support.

Note: Sometimes it w ill be neces sary to turn up the draw bar suppo rt earlier to level the trailer.

3. Installation

R59770490 B-16 MOBILE LED 07/01/2010

23

3. Installation

3.3 Powering the B-16 Mobile LED

Check fuel level before starting the gene rator.

With the build-in generator

1. Connect the grounding conductor to a grounding rod or other acceptable earth grounding method. Use the delivered wire and

grounding pin.

Image 3-7
Generator connections

1 Ground wire connection
2 B ackup battery connection (connection cable supplied)
3 Generator start key
4 Generator output
5 Input power distribution

2. P ut the contact in the wa rm up position (on).

3. A fter several seconds turn-on the generator with the contact key.

Let the engine run for a f ew seconds before charging.

4. P lug in the power cable com ing from the generator output to the power distribution input.

For more information about t he generat

or and the maintenance program of the generator, consult the manual

delivered w ith the generator.

CAUTION: Never let the diesel engine run for long er periods (>30 min) without charge or sm a ll loads (<15%).

This could result in se vere damage to the diesel engine.

Use of external battery

If the battery is weak or when you have an exhausted battery, then use an external battery to start up the engine.

Connect the delivered battery cable to the battery extension connector on the generator and connect an external battery to the other
side of the cable (or use a battery ch arger).

24

R59770490 B-16 MOBILE LED 07/01/2010

Image 3-8
External battery connection

1 B attery cable
2 E xternal battery connector

About cooling the generator

• Make sure there are no obstructions at the fresh air intake.

• Make sure the hot air can leave easily through the grid.

• Make sure that the exhaust gases can escape easily.

3. Installation

Never run the generator in an inappropriately ventilated room !

With an external power source

Connect an external source (3 conductors + neutral) to the input power distribution connector.

Image 3-9
1 E xternal power connection

Power distribution inside the B-16 Mobile LED

All internal power distribution is done via the distribution panel.

R59770490 B-16 MOBILE LED 07/01/2010

25

3. Installation

Image 3-10
Power distribution

1 Wall outlets control center

2 Lighting inside the B-16 Mobile LED

3 Pump

4

Outlet to the wall

26

R59770490 B-16 MOBILE LED 07/01/2010

3.4 Lifting the first part

What has to be done ?

LED wall is stored in 3 parts inside the trailer. One part has to be mounted on the other us ing the built-in lifting system.

Note about the hydraulic pump

When the pump is unused, it autom atically stops after 3 to 5 minutes. A restart is necessary.

Execute the next steps

1. Insert the sequence p in.

3. Installation

Image 3-11
1 S equence pin
2 Security pins (3x )

2. S tart up the pump by pushing the blac k button.

(Pump is m ounted on top of the generator)

Image 3-12
Pump system

3 S tart button
4 Lifting handle

3. L ift up the wall until it is 20 cm abo ve the second part.

Caution: Be careful not to lift up too much otherwise the w all guide become s loose from the mast.

R59770490 B-16 MOBILE LED 07/01/2010

27

3. Installation

Image 3-13
Tile guides

1 Guide on the wall
2 Guide on the mast side

4. O pen the tile locks of the lifted row.

28

R59770490 B-16 MOBILE LED 07/01/2010

3. Installation

3.5 Assembling first part on second part

What has to be done?

The trolley with the second part has to be moved forward and the first lifted part must be slowly lowered down on the second pa rt.
Everything m ust be locked together.

How to assemble

1. Release the transport holder. Pull out the security lock (1).

Place the lock on the magnetic strip on the inside of the transport holder.

Image 3-14
Unlock transport holder

1 Lock

2. P ivot the arm support to the top of the trailer until it clicks with its magnetic plate to the ceiling of the trailer.

3. U nlock the floor locks on both sides.

Image 3-15
Assemble both parts

3 Floor lock

R59770490 B-16 MOBILE LED 07/01/2010 29

3. Installation

4 Tile lock

4. S lide the trolley forward and secure into the next hole at both sides of the trolley.

5. S lowly lower down the mast until part 1 fi ts exactly on part 2.

Note: Do not lower down too much.

6. Close the tile locks as illustrated.

Image 3-16
Closing tile lock s

Note: It might be necessary to use the tile lock tool to lock the tile. Especially in the middle inside the display guide.

7. P lug in the power and data cables if not yet mounted.

30

R59770490 B-16 MOBILE LED 07/01/2010

3.6 Assembling third part on the first two

How to assemble

1. L ift up the mast until the half of the red marker is visible.

2. P ull out the s equence pin for 50% (just until the line on the pin is visible).

Tip: If there is too much resistance, move down the mast a little.

Image 3-17
Sequence pin, half out

3. L eft up the mast until the safety hole becomes completely accessible.

Note: Due to friction inside the mast, it is possible that hole is not accessible. Lower down the mast again and retry.

Caution: When the cables are already connected to the tiles it is possible the tension on the cables will be too big when you

The a ssembled display parts will be much higher then the third part of the display.

4. Insert the second safety pin and turn a quarter.

This safety p in is placed to work in a secu re d area while moving the trolley.

5. U nlock both floor locks of the trolley.

6. S lide the trolley forward and secure both sides into the third hole.

Caution: Pay attention to the location of the cables so that the wheels of the trolley not override these cables (severe dam age

7. o pen th e locks of the tiles.

8. Remove the safety pin again and move down the mast until the assembly fits exactly on part 3.

Note: Do not lower down too much.

9. Close the tile locks.

10.Plug in the pow er and data cables if not yet done.

lift the display more than necessary.

to the cables is possible).

3. Installation

R59770490 B-16 MOBILE LED 07/01/2010

31

3. Installation

3.7 Position screen out of the trailer

How to position

1. L ift up the mast until the safety hole becomes completely accessible and insert the safety pin.

2. L ift up the mast until a red marker sign appears on the mast.

3. Remove sequence pin c ompletely.

4. L ift up the mast until the next red marker is visible.

5. Insert the last safety pin at the bottom of the mast.

Image 3-18
Bottom security pin

6. L ift display to its top position.

Note: Check cables.

Display is fully out of the trailer.

7. S witch off the pump.

8. U nlock the turn table.

Image 3-19
Turn in g ma st

1 Unlock - lock handle
2 Neutral position
3 Turn handle

The red sign on the turn table indic

ates the neutral position of the display.

9. Turn manually the turn table until the display is in its desired position ( -90° and +90° out of its neutral position).

Check cables while turning the display.

10.Always lock the turn table by closing the lock handle.

Possible loose of pressure

When the display is fully out, the hydraulic pressure can slowly go down. The mast/display can lower perhaps 30 cm but not more
as the safety locks prevent it from g

If this loose of pressure is an issue, it is possible to avoid that loose of pressure by closing the valve at the bottom of the trailer when
the wall is fully out.

32

oing down more. Even when it is down for 30 cm, the wall is still out of the trailer.

R59770490 B-16 MOBILE LED 07/01/2010

Before moving down the display, do no t forget to reopen the valve.

Image 3-20
Hydraulic valve

3. Installation

R59770490 B-16 MOBILE LED 07/01/2010 33

3. Installation

34 R59770490 B-16 MOBILE LED 07/01/2010

4. MOVING DOWN THE DISPLAY

Move d own the display when the wind force is 7 beaufort.

Make sure t he display is switched off.

4. Moving down the display

R59770490 B-16 MOBILE LED 07/01/2010 35

4. Moving down the display

4.1 Disassembling the lower part

How t o disassemble

1. Unlock the turn table and turn it to its neutral position (red marke r). Lock this position.

Image 4-1
Turn ta ble

1 Unlock - lock handle
2 Neutral position indication
3 Turn handle

2. Remove t he security pin at the bottom of the mast.

Turn the pin a quarter turn and take it out.

Image 4-2
Security pin

3. M ove down the mast until the second security pin is reachable.

4. Remove the s econd security pin.

Turn the pin a quarter turn and take it out.

Image 4-3
Second security pin

5. M ove down the mast until the third security pin is reachable.

36

R59770490 B-16 MOBILE LED 07/01/2010

6. Remove the third s ecurity pin.

Turn the pin a quarter turn and take it out.

7. M ove down the display until the lower part matches the pins on the trolley.

The bottom tile locks must be closed while moving down the display.

Note: Watch out that cables are not under the display.

Image 4-4
Locking first part

8. O pen the tile locks between the lower part and the middle part.

Note: If necessary, use the tile lock tool to open the locks.

4. Moving down the display

Image 4-5
Open tile locks

9. Insert the sequence pin for 50%.

Image 4-6
Sequence pin half

1 S equence pin

Note: Due to friction inside the mas t, it is pos sible that the pin cannot be inserted. Move the mast a little bit up or down until it

is poss ible to insert the pin.

10.Lift up display until it becomes free from the second part (lift up maximum 15 cm).

Caution: Do not lift up more, otherwise the tile lock in the middle of the display (inside the tile guide) will be damaged

11.Close all tile locks.

R59770490 B-16 MOBILE LED 07/01/2010

37

4. Moving down the display

It is necessary to close the locks to avoid damage to the locks as they can push against the generator while lowing down the wall.

12.Unlock the trolley on both sides and slide it backwards until it locks in the next lock holes.

Image 4-7
Trolley lock

38 R59770490 B-16 MOBILE LED 07/01/2010

4. Moving down the display

4.2 Disassembling the middle part

How t o disassemble

1. Remove the sequence pin.

2. M ove down the display until it fits on the pins of the trolley.

Note: Watch out that cables are not underneath the display are m ight get damaged.

3. O pen the top tile locks.

Note: If necessary, use the tile lock tool to open the locks.

Image 4-8
Open tile locks

4. L ift up the third part of the display over 20 cm . Check the handle inside the display guide while lifting up the display to avoid

damage.

5. Close all tile locks.

6. Unlock the trolley and slide it b a ckwards until it locks in its transport position.

Check if the locks on both sides of the trolley ar e closed !

7. P ull the transport holder downwards and lay it on the tiles.

Pull the security lock from the backside of the arm and insert the lock to secure the trolley.

R59770490 B-16 MOBILE LED 07/01/2010

39

4. Moving down the display

Image 4-9
Transport lock

1 Lock

40 R59770490 B-16 MOBILE LED 07/01/2010

4.3 Move down the last part

How to move down

1. M ove down the display until it fits on the pins of the trolley.

Note: Watch out that cables are not underneath the display. Da mage might occur.

Display is disass embled an d trailer ceiling is closed.

2. S witch off the pump.

4. Moving down the display

R59770490 B-16 MOBILE LED 07/01/2010

41

4. Moving down the display

4.4 Stop generator

How to stop

1. L et the generator run a t no load for a few more minutes.

The generator can c ool down.

2. S top the generator with the start k ey.

42

R59770490 B-16 MOBILE LED 07/01/2010

4.5 Preparing for departure

Steps to be taken

1. Turn down the 4 stabilizers until the wheels reach the ground.

2. Turn down the draw bar support on the ground.

3. Retract the 4 stabilizers.

4. P lace the 4 wooden supports back into the trailer.

5. Couple the trailer on the vehicle hitch.

6. R elease the break system.

7. Turn up the draw bar support.

4. Moving down the display

R59770490 B-16 MOBILE LED 07/01/2010

43

4. Moving down the display

44 R59770490 B-16 MOBILE LED 07/01/2010

5. Maintenance, Service

5. MAINTENANCE, SERVICE

Overview

For maintenance, service and r epair on the B-16 Mobile LED please consult qualified service technicians/personnel.

Servicing is required when the B-16 Mobile LED has been damaged in any way, such as hydraulic mast or generator is damaged,
the B-16 M obile LED does not operate normally.

R59770490 B-16 MOBILE LED 07/01/2010

45

5. Maintenance, Service

5.1 Service and maintenance table

Overview

Below a service and maintenance overview table. For more information on the different parts, consult the respective m anuals.

Daily 500 km Quarterly Yearly

L

Trailer

Towbar Attachment to front

inertial brake
system

Axles Wheel bolts

Tires Pressure

Lights back-, front-lights

Outriggers Functioning

Frame Transverse at side section

Trailer enclosure

Doors Lock system (inside)

transverse

Attachment to 1st axle

Height adjustable bracket
system

Umbilical cord

Jockey wheel

hitch coupling

Course when braking
(barking action)

Grease nipple

Braking distance

Brake grips

Hand brake

Bearing clearance

Control cable

Brake linings

Brakes

Bearing surface

Pressure of replacement
tire

Wheel wrench available

plug

Light cable

Light cove r

Attachment

support for girders

girders of mast

Transverse at compressor

Splashguards

Functioning doors

Door frame

Functioning lock

Rubber of door frame

C

TClCLTClCLTClCLTCl

46 R59770490 B-16 MOBILE LED 07/01/2010

5. Maintenance, Service

Door stops

Door hinges

Nails

Walls

Roof attachment to side frames

Floor attachment

Display system

Pump leak s

Rotation system lubricate

Mast

Generator

general

exhausts fixing

surrounding frames

nails

attachment to m ain frame

inside wall paneling

wall control room

attachment to display grid

holes for water evacuation

oil level

lever

attachment to frame

attachment bolts 2x

functioning

oil losses of main cylinder

cylinder flexible

attachment to grid

motor

alternator

oil

gas - diesel

state

Daily 500 km

C

LT

Cl C

LT

Cl C

Quarterly

LT

Cl C

Yearly

LT

Cl

C = Control

L = Lubricate

T = Tighten

Cl = Clean

After 50h00 the diesel generator needs to get its fi rst maintenance. Please refer to the Kubota and Leroy
Somer manuals as well as "Service and Maintenance of the Generator ", page 48 for more information on
maintenance of the generator.

Used oil in the B-16 Mobile LED

Oil used in the generator is 10 W 40 for ambient temperature up to -20°C.

Hydraulic oil is SAE 35

R59770490 B-16 MOBILE LED 07/01/2010 47

5. Maintenance, Service

5.2 Service and Maintenance of the Generator

Parts

The B-16 Mobile LED is equipped with a diesel-fueled generator. T he generator is composed of a diesel motor from Kubota (KUB­OTA D1105) and an alternator from Leroy Somer ( LSA 37M8).

Alternator

The alternators are maintenance-free. A periodic check of the alternator is not necessary. A regular visual control o f the different
alternator parts – and especially of the rotor bearing – at ev ery engine maintenance is enough.

Engine

Check engine manual for maintenance intervals.

Below you will findalistofofficial service centres for the Kubota and Leroy Som er components. Please refer to their respective
manual for more detail on these components and their maintenance.

CAUTION: The diesel generator needs after 50h00 its first maintenance run.

Remarks

In the factory, the radiator has been fi lled with coolant for use up to -1 5°C.

The engine has been filled in the factory with 10W 40 oil (up to -20°C). If a lower temperature is needed, fi ll with 5W40 oil (up to

-30°C).

Service intervals

For a detailed explanation of the service intervals, consult t he service and maintenance m anual of the generator.

Interval Items

Every 50 hours

After first 50 hours Change of engine oil

Every 100 hours

Every 200 hours

Every 400 hours

Every 500 hours

Every one or two months

Every year

Every 800 hours

Every 1500 hours

Every 3000 hours

• Check of fuel pipes and clamp bands

Cleaning of air cleaner element

Cleaning o f fuel filter

Check of battery electrolyte leve l

Check of fan belt tightness

Check of radiator hoses and clamp bands

Replacement of oil filter cartridge

Replacement o f fuel filter cartridge

Removal of sediment in fuel tank

Cleaning of water jacket (radiator interior)

Replacement of fan belt

Recharging of battery

Replacement of air cleaner elements

Check of damage in electric wiring and loose c onnections

Check of valve clearance

Check of fuel injection nozzle injection pressure

Check of turbo charger

Check of injection pump

Check of fuel injection timer

A

1

A

2

3

3

3

3

48 R59770490 B-16 MOBILE LED 07/01/2010

5. Maintenance, Service

Interval Items

Every two years

Legend

A : Must be done after the first 50 hours of operation.

1 : Air cleaner should be cleaned m ore often in dusty conditions than in normal conditions.

2 : After 6 times of cleaning.

3 : Consult your local Kubota dealer for this service.

4 : Replace only if necessary.

When the battery is used for less than 100 hours in a year, check its electrolyte yearly (only for refi llable batteries).

Change of radiator coolant (L.L.C.)

Replacement of battery

Replacement of radiator hos es and clamp bands

Replacement of fuel pipes and clamp bands

Replacement of intake air line

Overview service center

For Europe

Country Engine (Kubota) Alternator (Leroy Somer)

Austria

Belgium

Cyprus C/O SG A Dorman

Denmark Stiga Belos AB Denmark

Eire

Finland Kesko Machinery Finland

France

MAG M otoren GmbH

A-5023 Salzburg

Tel. [phone]

Fax. [phone]

Matermaco S .A.

1030 Brussel - Bruxelles

Tel. [phone]

Fax. [phone]

2600 Glostrup

Tel. [phone]

Fax. [phone]

EL-GE Eng ineering Ltd.

Kildare

Tel. [phone]

Fax. [phone]

SF 01301 Vantaa

Tel. [phone]

Fax. [phone]

Kubota Europe SA

Argenteuil Cedex

Tel. [phone]

Fax. [phone]

L-S Elektroantriebe GmbH

A-1180 Wien

Tel. [phone]

Fax. [phone]

Leroy Somer Belgium

2800 M echelen

Tel. [phone]

Fax. [phone]

Limassol

Tel. [phone]

Fax. [phone]

Leroy-Somer Danmark

DK-5230 O dense M

Tel. [phone]

Fax. [phone]

Leroy Somer Finland

OY 00140 Helsinki

Tel. [phone]

Fax. [phone]

3

4

R59770490 B-16 MOBILE LED 07/01/2010 49

5. Maintenance, Service

Country Engine (Kubota) Alternator (Leroy Somer)

Germany

Greece Agripan S.A.

Italy SAIM S .P.A.

Malta

Netherlands

Norway Univ. Diesel Broddway

Portugal Fatomipe

Spain Transdiesel Div. de Casli

Sweden

Switzerland Hamilton AG Ind. Equipm.

UK Kubota Limited

Kubota D. Engine Division

63110 Rodgau

Tel. [phone]

Fax. [phone]

11855 Athens

Tel. [phone]

Fax. [phone]

20090 As sago (MI)

Tel. [phone]

Fax. [phone]

Gaetano Caruana Limited

Zebbug, MALTA G.C.

Tel. [phone]

Fax. [phone]

Gebr. Prins B.V.

2676 BD Maasdijk

Tel. [phone]

Fax. [phone]

1473 S kårer

Tel. [phone]

Fax. [phone]

3800 Aveiro

Tel. [phone]

28820 Coslada-Madrid

Tel. [phone]

Fax. [phone]

Broddway Norden

59623 Sk änninge

Tel. [phone]

Fax. [phone]

CH-8306 Brüttisellen

Tel. [phone]

Fax. [phone]

OX9 3UN Oxfordshire

Tel. [phone]

Fax. [phone]

L-S Elektromotoren GmbH

6000 Frankfurt/ Main

Tel. [phone]

Fax. [phone]

Moteurs Leroy Somer

11527 Athens

Tel. [phone]

Fax. [phone]

Leroy-Somer S PA

20020 Lainate (Milano)

Tel. [phone]

Fax. [phone]

Leroy Somer Nederland

3769 Bt-Soesterberg

Tel. [phone]

Fax. [phone]

Leroy-Somer Norge A/S

1371 Asker

Tel. [phone]

Fax. [phone]

Leroy-Somer Motores

1400 Lis bonne

Tel. [phone]

Fax. [phone]

Leroy Somer Iberica

Irun (Guipuecoa)

Tel. [phone]

Fax. [phone]

Gränsbovägen 6

S-151 4 2 Södertälje

Tel. [phone]

Fax. [phone]

Leroy-Somer S A

2557 Studen Biel/ Bienne

Tel. [phone]

Fax. [phone]

Leroy-Somer LTD

West Drayton Middlesex

Tel. [phone]

Fax. [phone]

50 R59770490 B-16 MOBILE LED 07/01/2010

5. Maintenance, Service

for Latin America:

Country Engine (Kubota) Alternator (Leroy Somer)

Argentina Argentagro S.R.L.

Buenos Aires 1068SO

Tel. [phone]

Fax. [phone]

Bahamas

Brazil Polus Ma quina Eletricas

Chili Clemsa

Columbia

Ecuador

Guadeloupe L-S Caraibe Services

Mexico D.E.I.

Venezuela L-S De Venezuela

Southeastern Power Prod.

FL33069 U.S.A.

Tel. [phone]

Fax. [phone]

Maipu/Santiago

Tel. [phone]

Fax. [phone]

L-S Burban Argentine

San Martin-Buenos Aires

Tel. [phone]

Fax. [phone]

Campuci Sao Paulo CE P 01524

Tel. [phone]

Moteurs Leroy Somer

Santiago

Tel. [phone]

Fax. [phone]

Fevacol

Bogota

Tel. [phone]

Fax. [phone]

C/O SDAD AMLAT

Quito

Tel. [phone]

Fax. [phone]

97195 Pointe à Pitre Cedex

Tel. [phone]

Fax. [phone]

CP 06 170 Mexico

Tel. [phone]

Fax. [phone]

Barquisimento

Tel. [phone]

Fax. [phone]

For Asia :

Country Engine (Kubota) Alternator (Leroy Somer)

Hong Kong

India Next corporation

Mumbai 400023

Tel. 91.

R59770490 B-16 MOBILE LED 07/01/2010 51

L-S Hong Kong Liaison

Kowloon Hong Kong

Tel. [phone]

Fax. [phone]

Beghum India Consultants

New Delhi 110008

Tel. [phone]

5. Maintenance, Service

Country Engine (Kubota) Alternator (Leroy Somer)

Indonesia

Israel FK Generators & Equipm.

Japan Kubota Osaka Head Off.

Korea

Malaysia

Oman Bahwan Engineering Co.

Philippines K. Agro-industrial Mach.

Saudi A rabia National Trading Co.

Singapore E & E Equipment PTE. LTD

Taiwan

Thailand

CV. Karya Hidup S entosa

Magelang Yogyakarta

Tel. [phone]

Fax. [phone]

Ind. Z. Holon PB 1729

Tel. [phone]

Fax. [phone]

Osaka 556-8601

Tel. [phone]

Fax. [phone]

Tado Co., LTD.

Seoul

Tel. [phone]

Fax. [phone]

Sime Kubota SDN.BHD.

47600 Petaling Jaya

Tel. [phone]

Fax. [phone]

Ruwi Area Code 112

Tel. [phone]

Fax. [phone]

1103 Quezon City, M.M.

Tel. [phone]

Fax. [phone]

Jeddah 21451 PB 2073

Tel. [phone]

Fax. [phone]

Singapore 0718

Tel. [phone]

Fax. [phone]

Amicaux Int. Corp.

Taiwan 106 R.O.C.

Tel. [phone]

Fax. [phone]

The Siam Kubota Ind. Co.

Bangkok 10800

Tel. [phone]

Fax. [phone]

Moteurs Leroy-Somer

Tel Aviv 66089

Tel. [phone]

Fax. [phone]

Moteurs Leroy-Somer

Tokyo 101

Tel. [phone]

Fax. [phone]

Moteurs Leroy Somer

Seoul

Tel. [phone]

Fax. [phone]

Kuasa Kita SDN BDH

47301 Petaling Jaya

Tel. [phone]

Fax. [phone]

Leroy Somer Saudi Arabia

Al Khobar 31952

Tel. [phone]

Fax. [phone]

L-S Southeast Asia

Singapore 2262

Tel. [phone]

Fax. [phone]

52 R59770490 B-16 MOBILE LED 07/01/2010

5. Maintenance, Service

Country Engine (Kubota) Alternator (Leroy Somer)

Turkey Altinboga

Istanbul

Tel. [phone]

Fax. [phone]

Un. Arab Emirates M. Tayyeb Khoory & Sons

P.O.Box 4664 Dubai

Tel. [phone]

Fax. [phone]

For Australia & Pacific:

Country Engine (Kubota) Alternator (Leroy Somer)

Australia Kubota Tractor A ustralia

Victoria 3043

Tel. [phone]

Fax. [phone]

New Guinea

New Zealand C.B. Norwood Distr. LTD.

Tutt Bryant Equipment

Rocklea QLD 4106

Tel. [phone]

Fax. [phone]

Palmerston North

Tel. [phone]

Fax. [phone]

SASIM Kemeralti

80020 Karaköy-Istanbul

Tel. [phone]

Fax. [phone]

Moteurs Leroy Somer

Ab-Dhabi

Tel. [phone]

Fax. [phone]

L-S Aus tralasia

New South Wales 2099

Tel. [phone]

Fax. [phone]

For Africa:

Country Engine (Kubota) Alternator (Leroy Somer)

Algeria

Egypt

Gabon Fabelec

Guinea Les ateliers de Guinee

Ivory Coa st Sorepel

Moteurs Leroy-Somer

Birkhadem Alger

Tel. [phone]

Fax.[phone]

Moteurs Leroy-Somer

Aguza-Cairo

Tel. [phone]

Fax. [phone]

Libreville

Tel. [phone]

Fax. [phone]

Conakry

Tel. [phone]

Abidjan 01

Tel. [phone]

Fax. [phone]

R59770490 B-16 MOBILE LED 07/01/2010 53

5. Maintenance, Service

Country Engine (Kubota) Alternator (Leroy Somer)

Morocco

Cogepra

20300 Casablanca

Tel. [phone]

Fax. [phone]

L-S M aroc

Casablanca

Tel. [phone]

Fax. [phone]

South Africa

Tunisia

Terraquip

Kempton P ark 1620

Tel. [phone]

Fax. [phone]

Promotechnic S.A. Z. I.

2013 Ben Arous Tunis

Tel. [phone]

Fax. [phone]

54 R59770490 B-16 MOBILE LED 07/01/2010

A. WIND SPEEDS

A. Wind speeds

R59770490 B-16 MOBILE LED 07/01/2010 55

A. Wind speeds

56 R59770490 B-16 MOBILE LED 07/01/2010

A.1 Wind speeds table

Overview table

Beaufort km/h mile/h m/s

11-51-3<2

2 6-11 4-7 2-3

3 12-19 8-12 4-5

4 20-28 13-18 6-7

A. Wind speeds

5

6 39-49 25-31 11-13

7

8 62-74 39-45 17-20

9 75-88 46-54 21-24

10 89-102 55-63 25-28

11 103-117 64-73 29-32

12 >=118 >=74 >=33

29-38 19-24 8-10

50-61 32-38 14-16

R59770490 B-16 MOBILE LED 07/01/2010 57

A. Wind speeds

58 R59770490 B-16 MOBILE LED 07/01/2010

B. DIMENSIONS

B. Dimensions

R59770490 B-16 MOBILE LED 07/01/2010 59

B. Dimensions

60 R59770490 B-16 MOBILE LED 07/01/2010

B.1 DimensionsofaB-16MobileLED

Overview

B. Dimensions

4800

2880

5480.7

2088

2300

Image B-1
Dimensions in mm

2500

3873

5044

6106

R59770490 B-16 MOBILE LED 07/01/2010 61

B. Dimensions

B.2 Specification of trailer

Overview

Specification

Gross weight

Max weight on couple 150 kg

Max weight pro axle 1800 kg

Length 6106 mm

Length w ithout draw bar 5044 mm

Width 2300 mm measured over mudguards

Height in drive position 2109 mm

Height top screen 5480 mm

Axles BPW 1800 kg, rubbersprings

Wheels and tyres 205 R14 - pressure in wheels, 3.75 bar

Brake BPW in draw bar

Drawbar BPW height adjustable 3500 kg 390 - 430 - 470

Screen dimensions

Generator power 11 kva 3000 cycles/min EPS113TDE

Hydraulic pump unit 1.5 kW - 3.1 cc - 220V

Functions hydraulic handles 1x

Stabilizers mechanical jacks 3500kg/stabilizer

Telescopic mast 4 elements

Lifting system mast

Rotating mast

Weights

Hanging bracket 100 kg

Tiles 915 kg

Electrical cabling 30 kg

Mast 450 kg

Tools 25 kg

Chassis + construction

Generator

Control roo m

Hydraulic unit 60 kg

Total weight 3330 kg

Value

3500 kg

l x w = 4800 x 2880

Hydraulic telescopic cylinder in mast

manually, mechanical lock 360°

1345 kg

345 kg

60 kg

62 R59770490 B-16 MOBILE LED 07/01/2010

B.3 Tile specifications

Specifications

Calibrated Brightness 6000 nit (calibrated at 6500 °K)

Certifications ETL, CE, FC C, RoHS, CCC, TUV

Colors

Contrast ratio

Hor. viewing angle

Interface

LED configuration black lamp LED - 1R, 1G, 1B

Lifetime

Link interface DVI interface (DVI connector)

Mains Voltage

Max link length

Max power cascade connection 3tiles

Max. hanging 10 m

Max. stacking 6m

Operatable digitizer DX-700 (with DVI output card)

Operating humid ity 10 – 99%

Operating temperature -35 – 50°C

Pixel density 3,906/sqm - 363/sqf

Pixel pitch 16 mm

Power consum ption maximum: 600W /m2

Processing 16-bit/color

Protection rating IP65/54

Refresh rate 800 Hz

Serviceability back (clickable shader)

Source compatibility CVBS, YC, YUV, RGB, DVI, SDI, HDSDI (DX700: and Dual link DVI, Dual link HDSDI)

Storage humidity 10 – 99%

Storage temp erature -35 – 50°C

Tile dimensions 960 x 960 x 281.95 mm

Vert. viewing angle

Weight

281 trilion

7,000:1

110° (min 50% brightness)

x2 DVI link

100,000 hrs

(@50% brightness)

200-240V / 50-60Hz

4.5 m (by Barco DVI cable)

D320

LED-PRO

3,600/tile (60x60)

average: 180W/m2

(with digitizer)

+15°/-35°

(min 50% brightness)

60 kg/tile (65 kg/m2) - 132.2 lbs

B. Dimensions

R59770490 B-16 MOBILE LED 07/01/2010 63