Baracoda BLUETOOTH L (1D), BLUETOOTH LA (LASER), RoadRunners Evolution-L 1D, RoadRunners Evolution-LA Laser Programming Manual
©
Baracoda
RoadRunners Evolution
Programming Guide
TM
–
November
2010
–L (1D) & -
LA (Laser)
Data Capture
for Workforce
in Motion
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 2 -
Data Capture
for Workforce
in Motion
SUMMARY
SUMMARY ................................................................... 2
REVISION HISTORY .......................................................... 4
INTRODUCTION .............................................................. 5
1. GENERAL CONFIGURATION ................................................. 6
1.1. G
ENERAL DEFAULT SETTINGS
................................................ 6
1.2. B
ARACODA ADVANCED FEATURES
............................................... 7
1.2.1. S
WITCH ON DELAY
.............................................................. 7
1.2.2. S
HUTDOWN TIMERS
.............................................................. 7
1.2.3. T
URN SCANNER
OFF ............................................................. 7
1.2.4. N
O DATA LOSS MODE AND BARACODA HEADER
............................................. 8
1.3. R
EADING MODE
.......................................................... 9
1.4. O
PERATING MODE
....................................................... 11
1.4.1. R
EAL TIME MODE
.............................................................. 12
1.4.2. NO D
ATA LOSS MODE - ENABLE
“ACK”
BEEP
.......................................... 12
1.4.3. NO D
ATA LOSS MODE - DISABLE
“ACK”
BEEP
.......................................... 12
1.4.4. R
EAL TIME - BUFFERED DATA OPTION
................................................ 12
1.4.5. B
ATCH MODE
................................................................. 13
1.5. T
HE DIFFERENT CONNECTION METHODS
......................................... 14
1.6. B
UZZER AND LED SETTINGS
................................................ 15
1.7. B
LUETOOTH SETTINGS
.................................................... 16
1.7.1. B
LUETOOTH NAME
.............................................................. 16
1.7.2. S
NIFF PERIOD SETTINGS
......................................................... 17
1.7.3. S
ECURITY (CODE
PIN)
SETTINGS
.................................................. 18
1.7.4. RF P
OWER EMISSION SETTINGS
.................................................... 18
1.8. D
ATA FORMAT
.......................................................... 19
1.8.1. T
IMESTAMP OPTION
............................................................. 19
1.8.2. D
ATA PREFIX/SUFFIX
.......................................................... 21
1.8.3. B
ARCODE PREFIX/SUFFIX
........................................................ 22
1.8.4. AIM S
YMBOLOGY IDENTIFIER
...................................................... 23
2. DECODER PARAMETERS ................................................... 24
2.1. D
ECODER DEFAULT SETTINGS
............................................... 24
2.2. E
NABLE/DISABLE ALL SYMBOLOGIES
.......................................... 24
2.3. S
ET DECODER BARCODE LENGTH
.............................................. 24
2.4. V
OTING
.............................................................. 25
2.5. MIN/M
AX LENGTH PER SYMBOLOGY
............................................ 26
2.5.1. S
YMBOLOGY TABLE
............................................................. 27
2.6. C
ODABAR SETTINGS
...................................................... 27
2.6.1. E
NABLE/DISABLE CODABAR
....................................................... 27
2.6.2. C
ODABAR START/STOP CHARACTERS
.................................................. 28
2.6.3. C
ODABAR CHECK DIGIT VERIFICATION
(AIM
RECOMMENDATION
) .............................. 28
2.6.4. S
ET LENGTHS FOR CODABAR
....................................................... 28
2.7. C
ODE 11 SETTINGS
..................................................... 29
2.7.1. E
NABLE/DISABLE CODE
11 ....................................................... 29
2.7.2. C
ODE 11 CHECK DIGIT(S) VERIFICATION
............................................. 29
2.7.3. T
RANSMIT CODE 11 CHECK DIGIT(S
) ................................................ 29
2.7.4. S
ET LENGTH FOR CODE
11 ....................................................... 29
2.8. C
ODE 39 SETTINGS
..................................................... 30
2.8.1. E
NABLE/DISABLE CODE
39 ....................................................... 30
2.8.2. E
NABLE/DISABLE CODE 39 FULL
ASCII ............................................. 30
2.8.3. C
ODE 39 START/STOP CHARACTERS
.................................................. 30
2.8.4. A
CCEPTED CODE 39 CHARACTERS
................................................... 31
2.8.5. C
ODE 39 CHECK DIGIT VERIFICATION
............................................... 31
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 3 -
Data Capture
for Workforce
in Motion
2.8.6. S
ET LENGTHS FOR CODE
39 ....................................................... 31
2.8.7. I
TALIAN PHARMACODE SETTINGS
.................................................... 32
2.9. C
ODE 93 SETTINGS
..................................................... 32
2.9.1. E
NABLE/DISABLE CODE
93 ....................................................... 32
2.9.2. S
ET LENGTHS FOR CODE
93 ...................................................... 32
2.10. C
ODE
128 S
ETTINGS
................................................... 33
2.10.1. E
NABLE/DISABLE CODE
128/EAN 128 ............................................. 33
2.10.2. S
ET LENGTHS FOR CODE
128/EAN 128 ............................................. 33
2.10.3. EAN 128: G
ROUP SEPARATOR
.................................................... 34
2.10.4. E
NABLE/DISABLE
AIM ID T
RANSMISSION
............................................ 35
2.11. I
NTERLEAVED 2 OF 5 SETTINGS
........................................... 35
2.11.1. E
NABLE/DISABLE INTERLEAVED 2 OF
5 ............................................. 35
2.11.2. I
NTERLEAVED 2OF 5 CHECK DIGIT
................................................. 35
2.11.3. S
ET LENGTHS FOR INTERLEAVED 2 OF
5 ............................................. 36
2.12. MSI C
ODE SETTINGS
................................................... 36
2.12.1. E
NABLE/DISABLE
MSI ......................................................... 36
2.12.2. MSI C
HECK DIGIT
............................................................ 36
2.12.3. S
ET LENGTHS FOR
MSI ......................................................... 37
2.13. S
TANDARD 2 OF 5 SETTINGS
.............................................. 37
2.13.1. E
NABLE/DISABLE STANDARD 2 OF
5 ................................................ 37
2.13.2. S
TANDARD 2 OF 5 CHECK DIGIT
.................................................. 37
2.13.3. S
ET LENGTHS FOR STANDARD 2 OF
5 ............................................... 38
2.14. UPC/ EAN S
ETTINGS
................................................... 38
2.14.1. E
NABLE/DISABLE
UPC/EAN ..................................................... 38
2.14.2. T
RANSMIT
EAN13 C
HECK DIGIT
.................................................. 39
2.14.3. T
RANSMIT
UPC-E C
HECK DIGIT
.................................................. 39
2.14.4. T
RANSMIT
EAN 8 C
HECK DIGIT
................................................... 39
2.14.5. T
RANSMIT
UPC-A C
HECK DIGIT
.................................................. 39
2.14.6. T
RANSMIT
UPC
NUMBER SYSTEM FOR
UPC-E .......................................... 40
2.14.7. UPC-A, UPC-E, EAN
CONVERSIONS
.............................................. 40
2.14.8. ISSN/ISBN
SETTINGS
........................................................ 41
2.14.9. ADD-
ON DIGITS SETTINGS
....................................................... 41
2.15. GS1 D
ATABAR
(RSS) 14 S
ETTINGS
........................................ 42
2.15.1. E
NABLE/DISABLE
GS1 D
ATABAR
14 ................................................ 42
2.15.2. GS1 D
ATABAR 14 CHECK DIGIT TRANSMISSION
........................................ 42
2.15.3. GS1 D
ATABAR 14 LINKAGE FLAG TRANSMISSION
....................................... 42
2.15.4. GS1 D
ATABAR 14 APPLICATION ID TRANSMISSION
..................................... 42
2.16. GS1 D
ATABAR
(RSS) L
IMITED SETTINGS
.................................... 43
2.16.1. E
NABLE/DISABLE
GS1 D
ATABAR LIMITED
............................................ 43
2.16.2. GS1 D
ATABAR LIMITED CHECK DIGIT TRANSMISSION
.................................... 43
2.16.3. GS1 D
ATABAR LIMITED LINKAGE FLAG TRANSMISSION
.................................... 43
2.16.4. GS1 D
ATABAR LIMITED APPLICATION ID TRANSMISSION
.................................. 43
3. APPENDIX 1: ASCII TABLE (A-Z, A-Z, 0-9, PUNCTUATION, CONTROL
CHARACTERS) .............................................................. 44
4. APPENDIX 2 – AIM SYMBOLOGY IDENTIFIERS STRUCTURE ..................... 49
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 4 -
Data Capture
for Workforce
in Motion
Revision History
Changes to the original manual are listed below.
Document Date Description
1.0 11 July 08 Initial release
1.1 26 Aug. 08 Update “Batch” section & add “The different connection method” section
1.2 11 Sept. 08 Add “Smart Autoscan” option.
1.3 02 July 09 Modify “Operating Mode” section & Add “buffered data” section.
1.4 25 Nov. 09 Correct EAN/UPC 5 digit add-ons active barcode
1.6 10 feb 10 Precision on ‘No duplicate scan’ feature
1.7 7 July 10 Modify “Define GS replacement character” barcode
1.8 28 Nov 10 1.3 : Add “Manual AutoScan”
1.5 : Complete “Master Mode” (ref to Master Connection Generator
Software)
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 5 -
Data Capture
for Workforce
in Motion
Introduction
The RoadRunners Evolution scanner can be programmed by scanning barcode labels which contain commands
for the decoder.
Programming labels must be Code128, with specific starting and ending characters. These labels will always be
read, even if Code128 symbology is disabled.
The scanner will acknowledge a good and valid programming barcode label reading with two beeps and a green
enlightening of the led. It will give two other beeps (lower tone) and a red enlightening of the led for either an
invalid or bad reading.
Please do not read the programming barcodes while being connected to the BaracodaManager software.
Programmable options are divided into 2 groups. The first group includes the options that show the general
behaviour of the scanner. The second group sets the decoding parameters for each barcode symbology.
This document concerns the Roadrunners 1D Evolution scanners, that is the BRR-L Evolution and the BRR-LA
Evolution.
All our documentations can be downloaded from the Partners download section of Baracoda website
(registration is required):
http://www.baracoda.com
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 6 -
Data Capture
for Workforce
in Motion
1. General Configuration
1.1. General default settings
The reading of the "Reset to factory settings” label turns all the parameters of the scanner back to default
settings and switches it off
Reset to factory settings
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 7 -
Data Capture
for Workforce
in Motion
1.2. Baracoda advanced features
1.2.1. Switch on delay
In order to switch on the scanner in its standard mode, you should just press the trigger. You can set up the
scanner to be switched on only after keeping the trigger pressed for two (2) seconds by reading the
appropriate barcode.
Switch on delay : 2 seconds
Switch on delay : 0 second (*)
1.2.2. Shutdown timers
There are two different ‘shutdown timers’:
- When connected timer: delay between the last scanned barcode and the switch off when the
scanner is connected to a host
- Not connected timer: delay between the last scanned barcode and the switch off when the scanner is
not connected to any host
It is possible to set those timers to ‘infinite’. In this case, the scanner will stay all the time ON.
Set shutdown timers to infinity
By default, timers value are:
- When connected timer = 20 minutes
- Not connected timer = 10 minutes
Set shutdown timers to defaults
1.2.3. Turn scanner OFF
To turn off the scanner, read the following barcode:
Turn off scanner
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 8 -
Data Capture
for Workforce
in Motion
1.2.4. No data loss mode and Baracoda Header
Baracoda header:
It is a proprietary data encapsulation. It is necessary to activate it to use the Baracoda keyboard emulation
(Kemul) and Terminal.
The Baracoda header is enabled in default settings
No data loss mode:
Baracoda has developed a proprietary communication protocol in order to enhance the security of the
Bluetooth transmission.
Every barcode sent to the host must be acknowledged by the host (until then, the scanner will transmit it again
and again).
This acknowledgment is disabled in default settings. It is strongly recommended to set this protocol
acknowledgment on when using the scanner with the BaracodaManager.
Enable Baracoda header
+ “No Data loss mode” ON
Enable Baracoda header + “No Data loss mode” OFF (*)
Disable Baracoda header + “No data loss mode” OFF
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 9 -
Data Capture
for Workforce
in Motion
1.3. Reading Mode
In
Trigger mode
, pressing the trigger will activate the beam.
Trigger (*)
The
Aiming trigger mode
has been developed for users who need to scan barcodes very close one to another
and they have to be sure to always read the correct one. Once in this mode, in order to read a barcode user will
have to press the trigger twice. Pressing it the first time will switch on the beam but will not switch on the
decoder (thus allowing user to aim at the correct barcode) while pressing the trigger the second time will
activate the decoder thus allowing the scanner to actually decode the barcode.
Aiming Trigger Mode
In
Autoscan mode
, the scan beam is continuously on. This mode enables to scan continuously.
Autoscan
In
Smart Autoscan mode
, for a battery power consumption optimisation issue, the scanner will be
continuously flashing.
Smart Autoscan
Manual Autoscan mode
Scanner behavior: when this capture mode is selected, pressing the trigger will switch ON the capture module
(beam & decoder) and keep it ON until the trigger is pressed again.
Note: in the case the trigger is not pressed the second time (to stop the manual autoscan) the beam will stay on
until the shutdown timer expires. When the scanner is switched ON, pressing the trigger will switch the beam on
continuously.
Enable Manual Autoscan
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 10 -
Data Capture
for Workforce
in Motion
The “
No duplicate scan”
option has been developed for users who do not want to scan twice the same
barcode consecutively.
« no duplicate scans
» disabled (*)
« no duplicate scans » enabled + error signal
If the same barcode is scanned, an error signal is played (two beeps (lower tone) and a red
enlightening of the led)
« no duplicate scans » enabled + no decoding
If the same barcode is trying to be scanned, it won’t be. The laser beam will still be enlightening.
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 11 -
Data Capture
for Workforce
in Motion
1.4. Operating Mode
Real Time mode
In real time mode, the barcode is decoded and transmitted to the remote host without any delay. If the
scanner is not connected, the data is lost.
Real Time mode with No Data Loss option
If the No Data Loss option is activated and if the scanner is not connected or out of Bluetooth range, the
scanner will store the data. It can memorise up to 10 000 barcodes (UPC format) and later automatically upload
them to the remote host when a Bluetooth connection is established to the host.
Every barcode sent to the host must be acknowledged by the host. If the host fails to send an
acknowledgement, the scanner will continue to transmit the barcode until the host does send an
acknowledgement.
This acknowledgment is disabled in the default settings. It is strongly recommended to set the No Data Loss
mode to ON. This configuration can be set with the BaracodaManager software or with the Programming
Guide.
Additionally, this protocol acknowledgment allows an end user to set an audio acknowledgment indicating that
the barcode has been successfully transmitted to the host.
Batch mode
Barcodes are always stored in the scanner. Once the batch mode is selected, the BCL led (right) emits an
orange flash. In batch mode, the barcode can read up to 10 000 barcodes (UPC format) and store them into its
non-volatile memory for later transmission to the host. When the internal memory is full, both Leds will be full
orange (no blinking).
To upload barcodes from the scanner, connect it to the host computer via Bluetooth. The BaracodaManager
software is used to configure the location where the barcodes are sent once the barcodes are extracted from
the scanner.
Once connected, the scanner will wait for the appropriate command in order to start uploading the barcodes:
this command can come from:
• The BaracodaManager: The user has to click on the button “Upload”.
• A configuration scan barcode: the user has to read the appropriate configuration barcode.
Be aware that with BaracodaManager, two (2) different ways to upload barcodes are possible:
• To an application window: In this case always double check before starting the upload
procedure that the cursor in your text window is active. Otherwise you will loose all the data
saved into your scanner.
• To a .txt file (default option). The BaracodaManager gives you the possibility to modify the
name of the file in which you may want to save the data.
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 12 -
Data Capture
for Workforce
in Motion
1.4.1. Real Time mode
Erases all captured data stored in memory and forces the scanner in Real time mode. No other setting is
changed.
Important reminder: if an ACK beep or buffer is needed, the scanner must be set in the “no data loss mode”
first.
Enable
Real Time with
« No Data Loss
»
mode
Enable Real Time without « No Data
Loss » mode
1.4.2. No Data Loss mode - Enable “ACK” beep
Forces the scanner in Real Time mode (with data acknowledgement); Erases all captured data stored in
memory. The scanner should have been previously set in the “No data loss mode” ON (So scan the “Enable Real
Time with No Data Loss mode” barcode before).
Enable
ACK beep
1.4.3. No Data Loss mode - Disable “ACK” beep
Forces the scanner in Real Time mode (without data acknowledgement); Erases all captured data stored in
memory. The scanner should have been previously set in the “No data loss mode” ON (So scan the “Enable Real
Time with No Data Loss mode” barcode before).
Dis
able ACK beep
1.4.4. Real Time - Buffered data option
It’s possible to set the scanner in “Real Time with No Data Loss mode” but with no bufferisation (buffer
configured to 0) when it’s not connected. In this particular situation the trigger will not activate the beam: so
impossible to read barcodes in this mode, and Both LEDs blinks orange.
Max Buffered Barcodes = 0
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 13 -
Data Capture
for Workforce
in Motion
1.4.5. Batch mode
BATCH MODE
Forces the RoadRunners Evolution in Batch mode. Erases all codes in memory
When in batch mode, the scanner will wait for the appropriate command in order to start uploading the
barcodes: this command can come
• from the BaracodaManager
• from reading the “Upload batch data” barcode here after
If this barcode is read when the reader is in batch mode and connected, the reader will automatically upload to
the host all the data in its memory. If not in batch mode or not connected, the scanner will ignore this barcode.
Upload batch data (with No Data Loss on)
When scanning this barcode, the scanner will send a message to the host, meaning that it wants to upload its
data. Following this, the host will launch the upload process and grab the batch data.
If the host application has received all the expected data, it will acknowledge the upload to the scanner which
will erase the data from its memory. If not, the host application will send a negative acknowledgment message
to the scanner which will keep the data in memory, ready to retry an upload.
If the data transfer has been successful (the scanner has received the acknowledgment and erased its memory)
and, for any reason, the user gets to realize that data has been lost at a higher level (keyboard emulation for
example), it still has the possibility to recover the last batch data into the scanner’s memory, by scanning the
below barcode.
Restore last batch data Restore last batch + launch upload
Please note that the data recovering won’t be possible if other barcodes have been scanned or if the scanner
has been shut down after the upload.
Max Buffered Barcodes = MAX
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 14 -
Data Capture
for Workforce
in Motion
1.5. The different connection methods
There are two (2) different way to create a connection from a Host and a scanner:
- Slave mode (by default)
The Host (PC, BaracodaManager, …) is creating the connection onto the scanner.
- Master mode
The scanner connects automatically to the Bluetooth address recorded in its memory. This connection
attempt is launched after a scan of the connection barcode. The configuration of the host address (to
which the scanner will connect) can be done:
o Via the BaracodaManager software (v3.35 and newer).
o Via a scan of configuration barcodes.
o Via Baracoda Master Connection Generator software (for PC)
All usage mode (Real Time, No Data Loss, Batch) are obviously available on those two different ways of
connection.
The configuration of the Host Bluetooth address (BDA) is made by scanning the 0-9, a-f, A-F labels (Appendix 1)
as on a calculator; following the timestamp format shown above.
For example: to set the following BDA: 00:c3:EF:44:a2:B9, the user will scan:
- “Set Remote BDA” label,
- “0” label,
- “0” label,
- “c” label,
- “3” label,
- “E” label,
- “F” label,
- “4” label,
- “4” label,
- “a” label,
- “2” label,
- “B” label,
- “9” label,
- “End of Config” label.
\ V T \ V T Z \ N U L \ S O H \ S O H \ F F \ F F
Enable master mod e
\ V T \ V T Z \ N U L \ S O H \ N U L \ F F \ F F
Disable master mode
\ V T \ V T Z \ N U L \ S T X \ S O H \ S O H \ F F \ F F
Enable master mod e and disconnect
\ V T \ V T Z \ N U L \ S T X \ N U L \ S O H \ F F \ F F
Disable master mode and disconnect
\ V T \ V T ^ \ N U L \ S O H \ E N Q \ L F \ L F
Set Remote BDA
\ L F \ L F E N D \ F F \ F F
End of Config
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8 - 15 -
Data Capture
for Workforce
in Motion
1.6. Buzzer and Led Settings
You can use these options to enable or disable the buzzer and / or the Led.
LED ON (*)
LED OFF
Good read beep on (*)
Good read beep off
ACK beep on (*)
ACK beep off
Beep level volume = HIGH (*)
Beep level Volume = LOW
BUZZER ON (*)
BUZZER OFF
Loading...