DIFFUSE
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q08
Diffuse Mode
52.5 mm
2.5 in
40.0 mm
2.0 in
37.5 mm
1.5 in
25.0 mm
1.0 in
12.5 mm
0.5 in
0
0
2.5 mm
5.0 mm
7.5 mm
2.5 mm
5.0 mm
7.5 mm
0
.1 in
.2 in
.3 in
.1 in
.2 in
.3 in
Q08
Diffuse Mode
DISTANCE
Q08 Series Opposed-Mode Sensors
Low-profile infrared sensors in rugged metal housings
• Miniature right-angle dc photoelectric sensors in rugged die-cast metal housings
• Ultra-thin; only 8 mm (0.3") deep
• Totally self-contained; 10 to 30V dc operation
• Easy mechanical alignment
• Circuitry is completely sealed and epoxy-encapsulated; rated IP67 and NEMA 6
• Select models with NPN (sinking) or PNP (sourcing) output
• Select light operate or dark operate models
• 3-wire hookup; output load capacity to 150 milliamps
• LED indicators for Power ON and Output ON; Output indicator may be used for
alignment
• Infrared, 880 nm
• Range of 2.5 mm to 61 mm (0.1" to 2.4")
Models Cable
NO5-Q08-AN7
NO5-Q08-AN7V1131
NO5-Q08-RN7
NO5-Q08-RN7V1131
NO5-Q08-AP7
NO5-Q08-AP7V1131
NO5-Q08-RP7
NO5-Q08-RP7V1131
2 m (6.5 ft)
3-Pin Pico QD
2 m (6.5 ft)
3-Pin Pico QD
2 m (6.5 ft)
3-Pin Pico QD
2 m (6.5 ft)
3-Pin Pico QD
Output
Type
NPN/LO
NPN/DO
PNP/LO
PNP/DO
Excess Gain Beam Pattern
Standard 2 m (6.5 ft) cable models are listed. To order the 9 m (30 ft) cable model, add suffix "W/30" to the cabled model number. For
example, NO5-Q08-AN7 W/30. Models with a QD connector require a mating cable. Performance based on 90% reflective white test
card.
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious
injury or death. This device does not include the self-checking redundant circuitry necessary to allow its
use in personnel safety applications. A sensor failure or malfunction can cause either an energized or deenergized sensor output condition.
P/N 03558 Rev. E 8/19/2013
2
1
Q08 Series Opposed-Mode Sensors
Overview
This small, rugged infrared diffuse proximity mode sensor is contained within an 8mm deep die-cast metal housing. It is totally self-contained and is powered by 10 to
30V dc. It is ideal for sensing of any reflective surface at up to 2 inches from the
sensor face. Typical applications include parts detection on small conveyors and in
robot grippers, and other similar short-range sensing applications.
Q08 diffuse sensors have a solid-state output capable of switching loads of up to
150 mA dc, continuous. Four output types are available: NPN sinking/light operate,
NPN sinking/dark operate, PNP sourcing/light operate, and PNP sourcing/dark operate.
A light-operate output conducts when the sensor sees the reflection of its own
modulated light (an object is present). A dark-operate output conducts when the
sensor does not see the reflection of its own modulated light (no object is present).
A green LED indicator, visible from the front and left side of the sensor, lights whenever dc power is applied to the sensor. An amber LED, visible from the front and
right side of the sensor, lights whenever the sensor output is conducting.
Specifications
Supply Voltage and Current
10 to 30V dc at 25 mA; 10% maximum ripple
Supply Protection Circuitry
Protected against reverse polarity
Indicators
Two LED indicators:
Green: Lights to indicate dc power ON
Amber: Lights when sensor output is conducting (in
“light” condition for light operate models; in “dark” condition for dark operate models)
Construction
Black epoxy-painted die-cast zinc housing, polysulfone
thermoplastic lens with two through-mounting holes to
accommodate M3 (#4) hardware
Environmental Rating
Meets NEMA standards 1, 2, 4, 6, 12 and 13; IEC IP67
Connections
PVC-jacketed 2 m (6.5 ft) or 9 m (30 ft) cable or 3-pin
Pico-style quick-disconnect (QD) fitting available. Cable is 4.0 mm (0.16 inches) diameter.
Operating Conditions
Temperature: 0 to +50 °C (+32 to +122 °F)
Maximum relative humidity: 90% at 50 °C (non-con-
densing)
Output Configuration
Solid-state dc output, with four output types available:
NPN sinking/light operate
PNP sourcing/light operate
NPN sinking/dark operate
PNP sourcing/dark operate
Light operate outputs conduct when the receiver sees
the reflection of its own modulated light source; Dark
operate outputs conduct when the sensor sees dark.
Output Rating
150 mA maximum, continuous
Off-state leakage current is 100 microamps at 30V dc
On-state saturation voltage is < 200 millivolts at 10 mA
dc and < 1 volt at 150 mA dc
Output Response Time
1 millisecond ON and OFF independent of signal
strength
Repeatability
200 microseconds (0.2 milliseconds), independent of
signal strength
Application Notes
The horizontal axis of the beam pattern represents a
line extending outward from the optical center of the
Q08 sensor, and perpendicular to the sensor’s lens.
For purposes of mounting and alignment, note that the
optical center of the Q08’s lens is not the same as its
mechanical center.
Certifications
2 www.bannerengineering.com - tel: 763-544-3164 P/N 03558 Rev. E
8.0 mm (0.32")
20.0 mm (0.79")
ø 3.40 mm (0.134")
(2 Holes)
#4 (M3) Screw Clearance
13.00 mm (0.512")
2 m (6.5') Cable
3.00 mm (0.118")
32.0 mm
(1.26")
3-pin Pico-Style
Quick-Disconnect
39.1 mm
(1.54")
7.7 mm
(0.30")
Optical
Center of
Beam
9.7 mm
(0.38")
10-30V dc
–
+
bu
bn
bk
Load
10-30V dc
–
+
bu
bn
bk
Load
10-30V dc
–
+
bn
bu
bk
Load
10-30V dc
–
+
bn
bu
bk
Load
Q08 Series Opposed-Mode Sensors
Dimensions
Cabled Models Quick-Disconnect Models Optical Center of Beam
Hookup Diagrams
NPN (Sinking Models)
Cabled Quick Disconnect (3-pin Pico-style)
PNP (Sourcing Models)
Cabled Quick Disconnect (3-pin Pico-style)
P/N 03558 Rev. E www.bannerengineering.com - tel: 763-544-3164 3
28 mm max.
(1.1")
ø 10 mm max.
(0.4")
4
3
1
20 mm
(0.8")
25 mm max.
(1.0")
ø 12 mm max.
(0.5")
Q08 Series Opposed-Mode Sensors
Accessories
3-Pin Snap/Pico-Style Cordsets
Model Length Style Dimensions Pinout
PKG3Z-2 2.00 m (6.56 ft) Straight
PKW3-2 2.00 m (6.56 ft) Right-Angle
1 = Brown
3 = Blue
4 = Black
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of
shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned
to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse,
abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND
WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL
BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY
PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.
www.bannerengineering.com - tel: 763-544-3164
Loading...