Banner PSDINA-24-4 DIN-Rail Power Supply User Manual

PSDINA-24-4 DIN-Mount Power Supply

24V dc, 4A Power Supply

Features

• Accepts universal AC input voltage (85 to 264V ac, 50/60 Hz); provides 24V dc output,
adjustable ±10%

• Provides reliable power for DC-powered sensors, cameras, and lighting systems

• Mounts to standard 35 mm DIN rail

• Protected against output over-voltage and over-current; LED indication of over- and

under-voltage, short circuit, and over-current conditions

DIN-Rail Mounting

To mount the Supply on a DIN rail, hook portion (A) of the Supply onto the rail; press in
direction (B) while pulling down slightly on portion (C) with a flat-blade screwdriver.

To dismount the Supply, pull down portion (C) with a flat-blade screwdriver and pull the
Supply away from the DIN rail.

A

B

C

CAUTION:

• For use in a protected (Pollution Degree 2) environment. Do not use in wet areas or in the presence of excessive airborne contamination.

• Use 75C copper conductors only. Tighten terminal screws to 9 in-lbs.

• Risk of electric shock. Do not open, disassemble, or modify this device.

• Terminal marked must be connected to a suitable ground. Failure to do so may result in a hazardous condition.

WARNING . . .

Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.

These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A
sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner
Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.

Printed in USA 01/09 P/N 134840 rev. A

Not To Be Used for Personnel Protection

PSDINA-24-4 DIN-Mount Power Supply

US

61

[2.4"]

11 1

[4.4"]

110

[4.3"]

118

[4.6"]

97

[3.8"]

Specifications

Input Voltage

Input Frequency

Input Current

(120 / 240V ac, 4A load)

Inrush Current

(120 / 240V ac, 4A load)

Output Voltage

Output Current

Output Power

Holdup Time

(120 / 240V ac, 4A load)

Line Regulation

(85 –264V ac, 4A load)

Load Regulation

(0–4A load)

Temperature Regulation

(4A load)

Total Output Regulation

(All conditions)

Efficiency

(120 / 240V ac, 4A load)

Output Ripple / Noise

(4A load)

Leakage Current

(120 / 240V ac, 1A load)

Power Factor

(120 / 240V ac, 4A load)

100 / 240V ac Nominal (85 to 264V ac)

50 / 60 Hz

2A / 1A

20A / 45A (< 10 ms)

24V dc Nominal (21.6 to 26.4V dc Adj.)

4A

96W

>25 ms / >100 ms

<0.1%

<0.8%

<0.02% / °C

<±5%

81% / 87%

Common Mode: <3.0% p-p
Normal Mode: <1.0% p-p

<0.25 mA / <0.50 mA

0.55 / 0.50

Dielectric Strength

(10 mA, 1 minute)

Output Over-Voltage
Protection and Indication

Output Under-Voltage
Indication

Output Over-Current
Protection and Indication

Operating Conditions

Mounting Clearance

Environmental Rating

Weight

Certifications

Standards – Emissions

Standards – Immunity

Standards – Safety

3.0kV ac (input to output)

2.0kV ac (input to ground)

0.5kV ac (output to ground)

Trip point: 30 to 33V dc (latching; cycle

ac power to reset)

Red LED: ON Green LED: OFF

<19.5V dc

Red LED: ON Green LED: ON

Trip point: 110% to 150% of rated current

(output disable; auto-retry)

Red LED: OFF Green LED: Flashing

Temperature: –10° C to +60° C

Derate load linearly to 50% from +50° C
to +60° C

Relative Humidity: 25 to 85%

Above, below, left, right: 25 mm (0.98")
Front: 15 mm (0.59")

IP20

590 grams

IEC61204-3 (CISPR 11 and CISPR 22
class B, IEC61000-3-2, IEC61000-3-3)

IEC61204-3 High severity levels
(IEC61000-4-2, IEC61000-4-3,
IEC61000-4-4, IEC61000-4-5,
IEC61000-4-6, IEC61000-4-11)

UL508

Dimensions

WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering

Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned
to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of
Banner products. This warranty is in lieu of any other warranty either expressed or implied.

P/N 134840 rev. A

Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: [phone] • www.bannerengineering.com • Email: [e-mail]