Baldor all products General Product Line Information

Information

General

General Information

Abbreviations: The Basic Baldor catalog number consists of a letter(s) prefix and several non-significant proceeding numbers. A suffix letter(s) and/or

number(s) may also be part of the catalog number. For example L3510 or L3510T. Following is a list of prefix and suffix definitions.

Catalog Number Prefix:

Single Phase

AEM Automotive Motor (GM7EHQ)

Motors

AF Aeration Fan Motor
AM Automotive (Motor GM7EQ)
ANF Auger Flange Motor
AO Air-Over Motor
AP Subfractional HP, PM Motor
AS Arbor Saw Motor

Industrial Motors

General Purpose

B Brake Motor
BC DC Motor Speed Control
BK Single Phase Gearmotor Kit
BLW Blower Kit
BMC Brushless DC Motor Control
BSM Brushless Servo Motors
BTG Tachometer Generator
BU Bushing Kit

Premium Efficient

Super-E® Motors

C NEMA C-Face with Base
CBL Cable Assembly
CD Wound Field DC Motor
NEMA C-Face with Base
CDP PM SCR Drive Motor
CDPT PM SCR Drive Motor
with Integral Tachometer
CDPWD Washdown PM SCR Drive
Motor, NEMA C-Face

Severe Duty

CDPSWD PM Paint Free Washdown SCR Drive Motor

Motors

C-Face with base
CDPX PM Explosion Proof SCR Drive Motor ­ C-Face with base
CDX Wound Field Explosion Proof
DC Motor, NEMA C-Face
CESWDM Paint Free Super-E Washdown - C-Face with base

Washdown Duty

CF Condenser Fan Motor
CHC Direct Drive Fan Motor with Resilient Base

Motors

CP Chemical Processing, Corrosion Protected Motor
CR Crusher Motor
CSC Checkout Stand Motor
CSM Baldor SmartMotor
CSSEWDM All Stainless Super-E Washdown-C-Face with base
CSSWDM All Stainless Washdown - C-Face with base

Explosion Proof

CSWDM Paint Free Washdown - C-Face with base
CWAM Dirty Duty Washdown - C-Face with base

Motors

CWDSM Baldor Washdown SmartMotor
D DC Shunt or Compound Motor
or Definite Purpose Soft Start Control
DE Vacuum Pump Motor
DG Gate Operator Motor
DMG Lifting Magnet Generator
DOC Door Operator Motor

Pump Motors Commercial

DR Double Reduction
E Super-E Premium Efficiency
E3H Super-E Premium Efficiency
HVAC Duty with Connection Box
located on top of Motor
ECP Super-E Premium Efficiency, Chemical Processing
Hostile Environment Motor
EN Encoder Kit
FM F-2 Mount Motor

Motors

FCD Drip Cover Kit
FD Farm Duty Motor
FFC Fan Cover/Conduit Box Kit
FL Flange Kit
G Subfractional HP Gear Motor
GC Permanent Split Capacitor and Split Phase
GCP Permanent Split Capacitor and Split

HVAC Motors

Phase Parallel Shaft Gearmotor
GD Centrifugal Fan Motor
GF 900 Series Reducers
GP Subfractional HP PM Motor
GPP PM Parallel Shaft Gear Motor

GSF Universal Series Right Angle Gear Reducers
GS Grain Stirring Motor
H Definite Purpose HVAC Motors
H3 HVAC Duty with Connection Box
located on top of Motor
HP Hydraulic Pump Motor
ID Inverter Control
IDM Inverter Drive Motor-TEBC
IDNM Inverter Drive Motor-TENV
IDWNM Washdown Inverter Motors-TENV
IDXM Explosion proof Inverter Drive Motors-TEFC
IM Irrigation Drive Motor
IR Instant Reversing Single Phase Farm Motor
J NEMA 56J Stainless Steel
Threaded Shaft with Dripcover
JM NEMA JM Pump shaft & Face with Base
JP NEMA JP Pump shaft & Face with Base
JSL Square Flange Pump Motors with threaded shaft.
K Model 34 Diameter Motor
with 56 C-Face, less Base
KN Model 34 Diameter TENV
Motor with 56 C-Face, less Base
L Single Phase
LRA Line Reactor
M Three Phase
M Multipurpose Soft Start Control
MM Metric Dimension Motor with Base
MPM Three Phase Metering Pump
MVM Metric Dimension Motor,
Flange Mount less Base
N Totally Enclosed Non ventilated
OF Design D, High Slip Motor (Oil Field)
P Pressure Washer Motor
P15 Pre-Engineered Control Panel
PSC Permanent Split Capacitor
R Repulsion-Start, Induction-Run Motor
RBT Roller Bearing Conversion Kit
RES Resolver Feedback Kit
RG Regeneration Resistor Assembly
RH Definite Purpose HVAC Motors
RL&RM Resilient Base(Cradle Mount)
RT Dynamic Braking Resistor Assembly
S Single Phase Soft Start
SD Series 23H Servo Control
SS All Stainless Washdown Duty
SWD Stainless Washdown Duty
T Torque Control
TA Torque Arm
TM Definite Purpose HVAC Motors
with Terminal Panel Endplate
TK Tachometer Mounting Kit
UC Universal Crop Dryer Motor
V NEMA C-Face less Base
VH Vertical Pump Motor, Normal Thrust
VJM NEMA JM Pump Shaft and
Face less Base
VLCP Vertical Pump Motor, Medium Thrust
VP PM SCR Drive Motor with
Metric Face or Flange
VPCP Vertical Pump Motor, High Thrust
WC West Coast Fit NEMA TCZ
WD Washdown Duty
WW Woodworking Motor
ZD Vector Control
ZDM Vector Drive Motor-TEBC
ZDNM Vector Drive Motor-TENV
ZDWNM Washdown Vector Motors-TENV

Catalog Number Suffix:

-2 120/240V Field

-277 277 Volt Winding

-4 460 Volt Winding

-5 575 Volt Winding

-8 200 Volt Winding

-9 NEMA Design C High Torque Winding

-12 12 Leads
/35 Full 140 Frame Band Diameter
/36 Full 180 Frame Band Diameter

-50 Wound for 50 Hertz Service

-2341 2300/4160 Volt Winding
A Automatic Thermal Overload
BV Blower Vented

-C Listing includes Class I, Group C

-CL Open Chassis Enclosure, Line Regenerative

-CO Open Chassis Enclosure, no internal braking
E Electric Switch

-E NEMA 1 Enclosure, built in Dynamic Braking

-EL NEMA 1 Enclosure, Line Regenerative

-EO NEMA 1 Enclosure, no internal braking

-ER NEMA 1 Enclosure, built in
Dynamic Braking Transistor

-I Explosion-Proof, 1.15 Service Factor
M Manual Thermal Overload

-MO Protected Chassis Enclosure,
no internal braking
P Wound Field DC Motor NEMA “AT” Frame

-P Partial AC Motor Excludes
R- Roller Bearing
T NEMA "T" Frame Dimension
TP Feather Picker Motor
TR NEMA “T” Frame-Roller Bearing
TS NEMA "TS" Frame Short Shaft
Pulley Endplate

-V12 12 Volt DC

-V24 24 Volt DC

-W NEMA 4 Enclosure

-WR Washdown Rating

Gear Reducer Suffix: 900 Series

A 56C Motor Flange
B 140TC Motor Flange
C 180TC Motor Flange
G Left Hand Output Shaft
H Double End Output Shaft
J Right Hand Output Shaft

Gear Reducer Suffix: Universal Series

A 56C or Right Hand Output Shaft
B 140TC
C 180TC

Grinder Catalog Number Suffix:

D Deluxe
E Exhaust Guards
W Wide Design

Other Abbreviations:

C Permanent Split Capacitor
L Capacitor-Start, Induction-Run Motor
LC Capacitor-Start, Capacitor-Run Motor
S Split Phase
X Explosion-Proof

6

CATALOG NOTES:

1 Class F Insulated Motor with 1.15 Service Factor or higher that

operates within Class “B” temperature limits at rated horsepower.
2 1.00 Service Factor.
3 Capacitor start, induction run.
4 Wye-start, delta-run.
5 Belted duty only, roller bearing.
6 F-2 Mounting
7 Companion voltages not available.
8 Class “H” Insulated.
9 Motors are not NAFTA qualifi ed.
10 These motors meet the hardware requirements of IEEE 45/ABS

and are not provided with Marine Plan Documentation.
13 Furnished without conduit box. Order kit P/N K56G3230.
14 Type CH (Capacitor Start - Capacitor Run).
15 Motors rated 208-230/460 are operable to minimum 200 volts.
17 Capable of 100% thrust in either direction.
18 Capable of 100% thrust stated in downward direction (out of motor)

and 40% upward thrust (into motor).
19 60/50 Hertz motor. 60 Hertz data shown, contact your local Baldor

offi ce for 50 Hertz data.
20 Class F Insulation.
21 Double bolt.
22 Base used for NEMA & above NEMA frames, 445T.
23 Two piece slide rails.
24 DOL or Part Winding Start.
25 DOL or Wye Start, Delta Run
26 Non-standard “BA” due to drive end bearing cooling fan.

Please refer to layout drawing.
27 Motors have ball bearing suitable for coupled loads. If load is belted,

a roller bearing may be required, contact your local Baldor offi ce.
28 Usable at 200 volts.
29 V-dimension is 2.5”.
30 Usable at 208 volts.
31 Suitable for 230/460, 60 Hz and 190-220/380-440 volts, 50 Hz.
32 Stearns brake.
33 Voltage at 60Hz.
34 Dodge D series brake.
35 Design A, also meets Design E inrush limits.
36 Can mount as 56, 143T & 145T frames with NEMA 56 shaft

dimensions.
37 Can mount as 56, 143T & 145T frames with NEMA 143T-145T

shaft dimensions.
38 Can mount as NEMA 56, 143T and 145T frames with NEMA 56

frame shaft dimensions.
39 Class F Rise
40 Brake motors may be mounted for vertical mounting with brake

below motor.
41 Brake motors may be mounted for vertical mounting with brake

above or below motor.
42 DODGE Short Series Brake.
43 Cannot be mounted vertically.
44 Shown as WPI enclosure.
45 Horizontal mount, no C-Face. May be converted to C-Face in
Mod Express or built as custom motors.
46 Includes 1024 ppr encoder.
47 BA dimension does not meet NEMA standards.
48 Includes phase insulation. Suitable for inverter duty.
49 Includes vertical lifting provision.
50 Cast Iron 140 Frame.
51 BISSC Certifi ed.
52 IP55 Enclosure.

53 Voltage at 50Hz.
54 Motors have NEMA standard BA dimensions.
55 Constant velocity fan: 115 volts, single phase.
57 Can mount as NEMA 145T frame with 145T frame shaft dimensions.
58 Can mount as NEMA 56, 143T and 145T frames with

NEMA 143T-145T frame shaft dimensions.
60 Totally-Enclosed, Non-Ventilated, Continuous Duty.
61 Copper bar rotor standard.
63 Foot also drilled for 447T frame mounting.
64 Motors include 100 ohm platinum winding RTDs and space heaters.
65 Capacitor start, capacitor run (two value capacitor).
66 Resilient mount single phase motors with moderate starting torque

for fan applications.
67 Voltage at 50//60 Hz.
68 3 lead.
69 6 lead suitable for part winding start on 200 volts.
70 Constant velocity fan: 230/460 volts, three phase.
71 Nominal effi ciency is based at the 1800 RPM (High RPM) and low

speed effi ciency is available just not published.
72 Orders shipped from a Reliance facility in 3 working days.

Motor is returnable for a restocking charge of $100 plus 10% of the

net motor price.
73 SCR Motors with a 3:1 constant torque speed range.
74 V-dimension is 3”.
75 Availability limited to current stock.
76 Flexible waterproof cover protects thermal overload reset button.
77 Inverter Duty.
78 Furnished without conduit box. Order Kit BKP2400.
80 Design criteria similar to motors in Commercial Duty Motors section.
81 5.5 inch frame – Aluminum end shield standard enclosure
82 6.3 inch frame – Aluminum end shield standard enclosure
83 Not suitable for use on motors which have model number with

“a, b or c” suffi xes
84 Does not meet NEMA BA for C-face footed motors
85 Can only be used on motors 1800 RPM and slower with ball bearings
86 Cannot be operated at full nameplate rating on 50 Hz rectifi ed power

supply
87 Tach adaptable with Thermostat
88 Sleeve bearings - coupled loads only.
89 Cooling fan on each end.
90 Includes thermostat.
91 Blower on drive end.
92 Force vent with blower and fi lter. Full nameplate rating on 50 Hz

rectifi ed power, AC supply voltage must be same as 60 Hz supply.
93 Force vent with blower, full nameplate rating on 50 Hz rectifi ed

power. AC supply voltage must be same as 60 Hz supply, thermostats

and tach provisions.
94 Force vent with blower, cannot run full nameplate on 50 Hz rectifi ed

power, thermostats and tach provisions.
95 Force vent with blower on drive end fi lter, thermostats and tach

provisions.
106 Finned aluminum frame construction.

EXPLOSION-PROOF MOTOR SYMBOLS:

Q Class I, Group D only, T2C.
W Class I, Group C & D, Class II, Group F & G, T4.
E Class I, Group D, Class II Group F & G, T3B
T Class I, Group C & D only, T3C
Y Class I, Group D only, T2A.
U Class I, Group D, Class II, Group F & G, T4.
I Class I, Group D, Class II, Group F & G, T3C.