Balboa Water Group GL2000 Configuration Guide
GL2000 Mach 3 Configuration Guide GL2000 Mach 3 Expander Board Options
123456789
J54
J97
FUSE F10A 250V
J3
F2
FUSE T0.3A
G
F5
J27
J26
HTR1
N
J23
J94
J95
J28
W4
240V
J32
F7
FUSE T30A 480V
J4
G
N
J55
W3
J68
K7 K6 K8
F1
J56
J79
T1
J98
K3
J5
A
B
C
FUSE T30A 480V
F6
J93
Balboa
G
N
BALBOA INSTRUMENTS, INC.
GL2000 TC MACH 3
P/N 22898 REV D
COPYRIGHT 2006
MADE IN U.S.A.
K2
W15
J99
J53
TB1
D
J96
E
J57
J59 J58
F
J101 J100
HTR2
123456789
Outut Features Quadrant
J1 2-Speed Pump 1 5-D
J2 Circ Pump (Separate Relay) 7-C
OR Fiber Optic Light
J3 1-Speed Blower (with 1-speed Pump 2) W15 to J97 3-A
OR 1-Speed Pump 3 (with 1-speed Pump 2) W15 to J99
J4 Audio Visual (always hot - no relay) 5-B
J5 2-Speed Pump 2 (with NO Blower on J3) W15 to J98 2-A
OR 1-Speed Pump 2 (See J3 and W15)
J9 Ozone (Separate Relay) 7-E
J12 Spa Light (10V or 230V) 8-D
ADCM SPLITTER KIT PN 54530
J6
ADCM SPLITTER
PN 54530
J2
© 2006
Balboa
MADE IN U.S.A.
P/N 22039_ A
J3
Required when using a Menu-driven
panel. Kit includes PCB, stand-offs,
and cable. Note: Software v29 or
higher required.
J1
TEST
• J2 connects to ADCM IN (J69) on
main PCBA.
• J3 connects to Menu Panel or
Transceiver.
• J6 connects to tester or F.A.S.T. station.
Balboa
Instruments
Incorporated
J41
J45
K4
J1
N
K11 K10
G
J60
SWITCHBANK A
J90
X-Mount P
Used for mounting any Expander Board
in a plastic enclosure.
Standoffs attach to heater mounting bracket.
10 VAC
Light Configuration
J33
K1
J45
W1
Light
Connector
NG
F4
W2
J33
J81
K9
J14
SWITCHBANK B
FUSE F3A 250V
J9
J56
K1
J2
G
W1
J31
J30
N
J12
NG
W2
N
G
EXT RELAY J6
CFG
J83
J13 J15 J17 J82J22 J24
EXT 2S P3 AUX F ALARM SEN A VAC SEN B
230 VAC
Light Configuration
J1
R
B
W
K11 K10
G
J17
TST
FUSE F3A 250V
F4
J91
J69
ADCM
J60
J71 J72
J70J10J39
J8
MAIN
PANEL
MAIN
PANEL
MAIN
PANEL
AUX
PANEL
AUX
PANEL
REMOTE
PN 53933
Light
Connector
X-P231 CE
PN 55025
P/N 22909 REV B
J7
J6
PN 55025
J36
EXT I/O
N
G
K2
A
W12
F5
F10A 250V
J2
B
X-B CE
Used for a 1-speed Blower output ONLY.
• W15 connected to J98
C
J6
J3
PN 53311
J1
R
B
W1
W
G
T30A 480V
X-P231 CE
Can replace the X-P CE in cases where branch circuit protection
is needed for high amperage devices that would over-burden
power input fuse F6 or F7 (4-C) on the main PCBA.
• J6 on X-P632 CE connects directly to Line AC
Use J27, J32, or J26 on the main GL2000 PCBA,
D
depending on AC Service Configuration.
E
J20
K2
F
J2
J4
X-P CE
Used for a 1-speed Pump or Mister output.
• W15 connected to J9z
J6
W12
N
G
J1
R
B
W1
W
G
T30A 480V
PN 53547
X-P632 CE
Used for a 2-speed Pump output or for two 1-speed
X-P632 CE
PN 55026
P/N 22909 REV B
J2
J6
PN 55026
Pumps. Can also be used for other optional setups.
• J6 on X-P632 CE connects directly to Line AC
Use J27, J32, or J26 on the main GL2000 PCBA,
depending on AC Service Configuration.
K2
J6
N
G
To Spa Light (J12) on
K1
W1
NG
FUSE F3A 250V
F4
W2
X-O3 CE (PN 53427)
J2
J4
X-FOW CE Kit
J7
N
W12
J5
PN 53976
G
Adapter PN 25338
GL2000
(230V Setup)
To J5 on X-O3 CE
Special setup with X-03 CE and Adapter PN 25338 to
operate a fiber-optic light and color wheel. Required when a Circ Pump
is installed on Main PCBA at J2.
Document PN 40502_L
04-05-2007
Loading...