Dolphin
TM
II
SPA ONLY
(CE Version)
Water-Resistant Remote Control
P/N 40421 Rev. A 06/21/2005
TABLE OF CONTENTS
Introduction..........................2
Installing Batteries .....................3
Features And Functions .................4
Spa Addressing........................6
Specifications.........................7
Troubleshooting.......................8
INTRODUCTION
The Dolphin™ II Remote is Balboa’s latest
generation remote control. It’s packed with easy-
to-use features such as:
• Pre-programmed technology for easy setup
• Color-coded keys to quickly locate popular
functions
• IR capability that can send commands to
your spa.
Follow the instructions detailed in this manual to
set up your Dolphin Remote and enjoy your new
remote control.
IMPORTANT! PLEASE READ:
Remote should be stored outside of spa when
not in use. Do not store in direct sunlight.
2
INSTALLING BATTERIES
1. On the back of the Dolphin™ II Remote,
remove the screws that hold the battery cover
in place and lift off the battery cover.
2 Obtain two (2) fully-charged AA
alkaline batteries.
Match the + and – marks on the batteries to
the + and – marks in the battery case, then
insert the new batteries.
3. Press the battery cover back into place, being
careful to align the rubber seal.
4. Replace the screws that hold the cover by
carefully starting each one without tightening
it. Once they are all started, snug up one
screw and then do the same to the screw on
the opposite side of the door. Repeat this in a
crossing pattern until all screws are snug.
Do not overtighten them. This will assure an
adequate water seal around the battery door.
5. Test the unit by pressing any mode key (LT, P1,
P2, P3 or BL).
If the batteries are inserted correctly, the LED
will blink once.
NOTE:
Whenever batteries need to be replaced, the
Dolphin will blink twice with every key press.
Simply replace the batteries and the remote will
be restored to its full functionality, complete
with your favorite settings.
3
FEATURES AND FUNCTIONS
Use the illustration below to locate the Dolphin
features and to learn how they function.
4
The LED (red light) blinks to show that the remote
control is working and is sending signals.
Use SETUP for all programming sequences.
Use these buttons to control available
spa functions.
Press LT once to turn on the Spa Light.
Press P1 once to turn on Pump 1.
Press P2 once to turn on Pump 2.
Press P3 once to turn on Pump 3.
Press BL once to turn on the Blower.
Depending on your spa, some buttoms may
control other equipment than indicated here.
5
SPA ADDRESSING
Your CE-compliant spa does not
support addressing.
However, in case addressing is ever enabled by
accident, follow the steps below to disable.
1. Press the SPA button on the Dolphin once
2. Press and hold SETUP until the LED blinks
once. It will then blink twice.
3. Press the B button on the Dolphin 4 times in a
row (BBBB).
4. If the code is entered correctly, the LED will
blink twice. Dolphin should now function
properly.
5. If your Dolphin remote is still not operating
correctly, check your spa manual to see if this
feature is available on your system.
If so, follow the procedure described in your
spa manual to enter a spa address
of 0 (no address) into your spa.
6
SPECIFICATIONS
Remote Control Power
2 AA Batteries
Remote Control Dimensions (H x W x D)
9-2⁄16 x 2-10⁄16 x 1-3⁄16 in.
232 x 65 x 31 mm.
Remote Control Weight (without Batteries)
8 oz (220 g)
NOTE: Specifications are typical. Individual units
may vary. Specifications are subject to change and
improvement without notice.
7
TROUBLESHOOTING
PROBLEM: LED does not blink when you press a key.
SOLUTION: Replace the batteries with two (2) new AA
PROBLEM: Dolphin does not control spa. LED blinks
SOLUTION: Make sure you are within 15 feet of the spa
alkaline batteries (see page 3).
when you press a key, but receiver does
not respond.
and aiming the Dolphin directly at the
receiver.
It is possible that addressing (which is
incompatible with your spa) has been
enabled accidentally. See the Spa
Addressing section for steps on how to
reset the Dolphin. (See page 6.)
8
Loading...