Balboa Water Group ADCM Splitter User Manual
Installation Instructions for the ADCM Splitter
G
W
W
8
U
MAIN
PANEL
M
P
L
M
PANEL
AUX
PANEL
AUX
PANEL
J
W2
R
J8
0
6
F
SWITCHBANK B
BHBIT
SW
AD
J3
J
G
W
W
8
U4
MAIN
PANEL
MAIN
PAN
MAIN
L
X
PAN
UX
L
J
W2
E
J8
9
0
0
A
F
2
S
B
G
W
W
8
L
L
L
E
9
0
0
1
0
6
F
2
B
G
W
W
8
ADCM
L
L
X
L
5
0
9
0
0
9
0
6
AU
F
Board and Menu Panel Training Instructions
The ADCM SPLITTER is required for using a
Menu-driven Panel on the following systems:
EL 2000 / 8000; GL 2000 / 8000
The Kit includes: PCB, 4 stand-offs, and cable.
Note: Software v29 or higher is required.
39
J39
10
4
70
71
J71 J70
2
J20 J10
69
J69
72
1
W
G
W13
SWITCHBANK B
W
G
J5
5
W12
AUX. F
AUX.
W2
G
J3
U4
J80
80
ADCM
MAIN
PANEL
3
J36
Disable the main Power to Spa
before proceeding.
Locate the mounting pattern for the ADCM board.
The rectangular hole pattern for mounting the
ADCM board on to the main board is
approximately 1.25 “ x 2.25”.
Note: Mounting location varies depending on
the system.
AUX
PANEL
AUX
PANEL
AIN
MAIN
PANEL
AIN
MAIN
ANE
PANEL
REMOTE
EMOTE
J1
TEST
W
G
SWITCHBANK B
W13
J3
AUX
E
PANEL
AU
AUX
E
PANEL
AIN
MAIN
E
PANEL
MAIN
EL
PANEL
REMOTE
EMOTE
J
J39
W
G
J5
J
W12
AUX. F
X.
W2
2
G
J3
U4
J80
8
ADCM
MAIN
PANEL
PANEL
3
J36
J3
1
7
71
J71 J70
2
J20 J10
6
J69
2
72
J6
ADCM SPLITTER
© 2006
Balboa
PN 54530
MADE IN U.S.A.
P/N 22039_ A
J2
J
2
Press the four standoffs into the
holes on the main board until they
snap into place.
AU
AUX
EL
PANEL
A
AUX
PANE
PANEL
MAIN
PANE
PANEL
MAIN
EL
PANEL
REMOTE
REMOT
J
4
W
G
W13
SWITCHBANK B
SWITCHBANK
W
G
J5
5
W12
J3
J6
AUX. F
AUX.
W2
2
G
J3
U4
J1
TEST
J80
MADE IN U.S.A.
P/N 22039_ A
ADCM
Balboa
© 2006
J2
MAIN
E
PANEL
3
J36
39
J39
1
7
7
J71 J70
2
J20 J10
6
J69
72
7
UX
AUX
PANE
PANEL
X
AUX
EL
PANEL
MAIN
PANE
PANEL
MAIN
EL
PANEL
REMOTE
REMOT
J
Attach the supplied cable from the Splitter
board (J2) to the main control board / ADCM
port (J69) panel. Be sure that the J1 jumper
has been removed.
3
39
W
G
J5
5
13
W13
SWITCHBANK B
WITCHBANK
W
G
W12
J3
J6
AUX. F
UX.
W2
G
J3
U4
J1
TEST
J80
MADE IN U.S.A.
P/N 22039_ A
ADCM
Balboa
© 2006
J2
MAIN
PANEL
36
J36
J39
1
J71 J70
J71 J70
J2
J20 J10
6
J69
72
7
Align the ADCM board over the plastic standoffs
and press down until the plastic standoffs snap
into the Splitter Board.
Be careful not to bend or crack the ADCM Splitter
board or other components.
Continued on reverse side
Installation and Training Instructions (cont’d)
5
J1
J2
BL
LT
If you have a Spa Side Panel, insert the
cable into J3. Turn power back on to the
Spa. The system will recognize the Spa
Side Panel immediately.
Jets 2Jets 1
102º F
LightBlower
HT
FC
OZ
Enter
If you have a Hand Held Panel, connect
the cable of the transceiver into J3. Turn
power back on to the Spa. Proceed to
step number 6.
J3
J1
TEST
OR
MADE IN U.S.A.
P/N 22039_ A
Balboa
J6
© 2006
J2
6
Linking the Hand Held Panel to the System
The hand held panel must be added, or “linked”
before it will communicate with the system.
Arrow Left
Arrow Up
Arrow Right
Arrow Down
Select
To Exit a Menu,
Arrow Left
To Link the Panel to the Spa Control System
“Home” > Set >
To link your wireless panel to the system, press
> Link Panel > .
.
Follow the on-screen instructions:
Shut off power to spa.
Turn spa power back on and
then push select on this
panel within 30 seconds.
Additional screens will follow: “Linking Panel...Please
Wait”; then, “Panel Linked Successfully”. “Starting
Up” will also blink.
If the “Priming Mode” screen appears, follow the
instructions. You’ll probably choose “Exit Priming
Mode” if you’re simply creating a link from the
Wireless Panel to the Spa Control System. Once
completed, “Acquiring System Config.” will blink on
the “Home” display.
Warning! Shock Hazard! No User Serviceable Parts.
Do not attempt service of this control system. Contact your dealer or service organization
for assistance. Follow all owner’s manual power connection instructions. Installation must be
performed by a licensed electrician and all grounding connections must be properly installed.
40804_A, June 13, 2007
Loading...