Balboa VS500Z User Manual

VS500Z Configuration Guide

1

2

3

4

5

6

7

CLASS G

FUSE 30A

F5

BLK AC

K6

J23

K1

J50

W10

F7 FUSE 20A 250V

J74

J61

J62

J17/26

A

J73

WHT AC

C

C

C

J66

J65

J11

J15

J16

J25

J63

J64

G

W4

G

G

W7

B

W1

K8

WHITE

NEUTRAL

F4 FUSE .3A 250V

T1

K9

C

BLACK

HOT

	TORQUE
	RANGE	HOT RED
K4	FOR TB1:				K3
	27-30 IN. LBS.				K2
D				TB1		J2
	J32	J33	J34	J35		J43

8

J46	J47	J29
	C		C
	G		G
	W2		K5
W3
J1 J1A
J2A
		1	2	3
		U4	J12

9

J20	F1
C	250V
G	3A
	FUSE
	J10
	J18

A

B

C

D

J36

J37

F2

RED AC

J13

E

J60

J22

J44

BALBOA INSTRUMENTS, INC.

2-SPD

E

J7

J8

VS500Z

EXT RLY

Balboa

HTR2

HTR1

S1

TST

MADE IN U.S.A

E.GND

J6

P/N 22972 REV D

J100

J101

SWITCHBANK A

EXT.

AUX. F

SEN. A

SEN. B

VAC

COPYRIGHT 2005

RLY

			1		2		3	4		5
Output Features									Quadrant
J23		+	W1	– 2-Speed Pump 1						4-A
				– OR 1-Speed Pump 1 with DIP Switch A5
J50		+	W4	– Audio Visual - always hot, no relay						6-A
J17/26		+	W7	– 1-Speed Blower (W3 to J46)						6-B
				– OR Single-Speed Pump 2 or Pump 3 (W3 to J62)
J47		+	W2	– Circ Pump						8-A
J29		+	W2	– Ozone (Same voltage as Circ Pump, if used)						9-A
				– Note X-03 option board for retro fit
J20				– Spa Light (12V only)						9-A

System can be factory configured for either a Duplex Topside Panel, a Serial Standard Panel, or a Serial Deluxe Panel.

Note: Some panels styles are not available depending on system configuration. Consult your Balboa product representative for details.

120V Conversion Option - Add jumper from Red AC (J32) to White AC (J11) and set DIP switch A10 to ON.

Balboa

Instruments

Incorporated

6	7	8	9

X-Mount P											PN 53933

Used for mounting any Expander Board in a plastic enclosure.

Standoffs attach to heater mounting bracket.

VS500Z Expander Board Options

K1	J6		X-P231	J7
			PN 53681
	C G
	J1	R
	W1		P/N 22909 REV B
		B
		W		J6
J2
J4	W12	G	F30A 480V

X-P

PN 53544

Used for a 1-speed Pump output.

	C	G
K1
F5	W12	J6
F10A 250V
J2	J3

X-P231

PN 53681

Can replace the X-P in cases where branch circuit protection is needed for high amperage devices that would over-burden power input fuse F5 (1-A) on the main PCBA.

•J6 on the X-P231 connects directly to Black AC by using J66 or J65 on the main board (1-B).

•Connect J7 wire on the X-P231 to J60 on the main board (7-E).

•Connect W1 on the X-P231 to Red AC on the main board (2-D).

X-B	PN 53310		X-P332
Used for a Blower output ONLY.				J7
			PN 55137
	J1	R
	W1		P/N 22909 REV B
		B
		W		J6
		G	F30A 480V

K1

J6

X-P332

PN 55137

C

G

Used for an additional 2-speed Pump output.

J7

C

G

• J6 on the X-P332 connects directly to Black AC by

J2

using J66 or J65 on the main board (1-B).

J4

J5 W12

• Connect J7 wire on the X-P332 to J13 on the main

board (9-E).

To J17/26

• Connect W1 on the X-P332 to Red AC on the main

board (2-D).

(Blower/P2)

VS-P2 Adapter Wire

PN 25339

To J5 on X-O3

NOTE Regarding J12 (Quadrant 9-D):

When J12 on the Main Board is jumpered on

pins 2 & 3, the system is in VS50xZ compatibility

X-2SP Kit

PN 53913

mode.

Adapter PN 25339 is used in conjuction with an X-O3 to

If J12 on the Main Board is jumpered on pins 1 & 2,

run a 2-speed pump 2. No Blower is available when this kit is used.

the system is in VS51xZ/VS5xxSZ/VS5xxDZ

• J4 connects to Black AC (3-A) using J61 or J62 on main board.

compatibility mode.

• Connect 2-speed pump to J7 on X-03.

Document PN 40540_M

1-30-2007