Badger Meter HREBT, ADEBT User Manual

BadgerTouch®

Automated Meter Reading System Remote Module

Models HREBT and ADEBT

BTA-DS-00233-EN-02 (June 2013)

DESCRIPTION

Applications: The BadgerTouch® Single Remote Module coupled

with the High Resolution Encoder (HRE) or Absolute Digital Encoder (ADE®) is a complete electronically encoded close-proximity automated meter reading system, specifically designed for single point remote meter installations. This system can be used with all currently available Badger Meter Recordall® Disc, Turbo, Compound, Combo, Fire Series meters and assemblies.

Communication: Communication is accomplished by using compatible reading devices programmed to read BadgerTouch or Sensus protocols, such as the VersaProbe reading wands, to interrogate the BadgerTouch remote module. The remote module responds with its serial number, water meter reading, and transmits data in approximately 2.5 seconds. In the event a tamper condition exists, the data collector will not receive a reading.

Performance: The Badger Meter BadgerTouch meter reading system offers operating performance in a variety of applications under most climatic conditions. For consistent results, interrogation equipment should be placed in direct contact with the remote read pad.

Meter Reading Validation: Further validation of the meter reading can be made automatically by the data collector based on comparison of high-low audit fields in the record. If the meter reading is not between these predetermined limits, an error message is displayed on the data collector display.

Wire Connections: The BadgerTouch Remote Module can be installed in new or existing installations where remote meter reading is required. The remote module is connected to the recommended wire that runs between the module and the HRE or ADE. A set of terminal screws on the remote module makes this connection. The HRE or ADE is provided prewired with a 3', 6', 10' 15' or 25' length of wire that is ready for connection in existing installations. Please see Figure 1 for more information on connections. To provide best results, a maximum of 75 feet of wire (Belden #9770) between the remote module and the encoder is allowed. Other wire types may also affect performance. If an additional length of wire is used in addition to that provided with the encoder, a set of gel splices must be made.

Construction: The Badger Meter BadgerTouch remote module enclosure is constructed of a high impact plastic enclosure designed for most remote locations. All internal electronic components are encapsulated to provide environmental protection. The HRE and ADE provide permanent glass/metal packaging in a plastic shroud and lid for long lasting, highly reliable encoded meter reading information collection.

License Requirements: This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes made by the user not approved by Badger Meter can void the user’s authority to operate the equipment. No license is required by the utility to operate a BadgerTouch meter reading system.

SPECIFICATIONS

Operating Temperature

Storage Temperature –5…120° F (–20…49° C)

Humidity 0% to 100% Condensing

Ultraviolet Remote enclosure is UV protected for

Construction The remote module has a high impact

Hardware Two terminal screws for connecting

Weight 6 ounces (not including the encoder)

–5…120° F (–20…49° C)

outdoor installation.

weather proof plastic enclosure containing encapsulated electronics and reading coil. The HRE and ADE is constructed of a permanently sealed glass and copper corrosion-resistant metal can design.

the HRE or ADE lead wire to the remote module.

Noncorrosive tamper resistant TORX® seal screw mounted on the HRE or ADE shroud and remote housing (optional proprietary keyed seal screw available).

Product Data Sheet

BadgerTouch

Remote Module

Cable

From Register

5' or 25'

Figure 1: BadgerTouch Single Remote Configuration

ADE, BadgerTouch, Recordall, and RTR are registered trademarks of Badger Meter, inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding contractual obligation exists. © 2013 Badger Meter, Inc. All rights reserved.

www.badgermeter.com

BadgerTouch®

Automated Meter Reading System Pit Module

Models HREBT and ADEBT

BTA-DS-00235-EN-02 (June 2013)

DESCRIPTION

Applications: The Badger Meter BadgerTouch® Single Pit Module

factory prewired to the High Resolution Encoder (HRE) or Absolute Digital Encoder (ADE®), is a complete electronically encoded closeproximity automated meter reading system, specifically designed for single pit meter installations. This system can be used with all currently available Badger Meter Recordall® Disc, Turbo, Compound, Combo and Fire Series meters and assemblies and is designed to fit pit lid configurations up to 2 inches thick.

Communication: Communication is accomplished by using compatible reading devices programmed to read BadgerTouch or Sensus protocols, such as the VersaProbe reading wands, to interrogate the BadgerTouch pit module. The pit module responds with its serial number, water meter reading, and transmits data in approximately 2.5 seconds. In the event a tamper condition exists, the data collector will not receive a reading.

Performance: The Badger Meter BadgerTouch automated meter reading system offers superior operating performance in pit applications and is designed for totally submerged environments. The pit module allows readings under many conditions where ice, sand, or dirt may impede direct contact with the read pad. For consistent results, interrogation equipment should be placed in direct contact with the pit read pad.

Wire Connections: The BadgerTouch Single Pit Module is factory prewired to the HRE or ADE and does not require additional wiring in the field.

Construction: The Badger Meter BadgerTouch pit module is constructed from high impact plastic material that is designed for mounting directly through the pit lid. There is a plastic cover that locks the pit module in place. Inside the pit, an integral plastic locking nut is used to fit the module firmly in place next to the pit lid. All electronic components internal to the enclosure are encapsulated to provide environmental protection. The High Resolution Encoder (HRE) and Absolute Digital Encoder (ADE) provides permanent glass/metal packaging in a plastic shroud and lid for long lasting, highly reliable encoded meter reading information.

SPECIFICATIONS

Operating Temperature

Storage Temperature –5…120° F (–20…49° C)

Humidity 0% to 100% Condensing

Construction

Hardware Non-corrosive tamper resistant TORX®

Weight 15 ounces (module and encoder)

–5…120° F (–20…49° C)

High impact plastic pit lid nut, adjustment nut, and encapsulated read coil within the plastic pit module. The HR

E and ADE are constructed of a permanently sealed glass and copper non-corrosive metal can design.

seal screw mounted on the HRE or ADE shroud (optional proprietary keyed seal screw available).

Product Data Sheet

1.75"

Diameter

Pit Lid

Hole

BadgerTouch™ Pit

Module

.25"

2" Max.

4.0"

Black Housing

5' and 25'

Cable Lengths Available

Figure 1: BadgerTouch Single Pit Prewired Configuration

www.badgermeter.com

+ 8 hidden pages

Badger Meter HREBT, ADEBT User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual