Electronic Preset Meter
Model EPM2-ADV-SF, Advanced Series, Special Fluids
AUT-UM-00916-EN-05 (August 2015)
User Manual
Electronic Preset Meter, Model EPM2-ADV-SF, Advanced Series, Special Fluids
Page ii August 2015
AUT-UM-00916-EN-05
User Manual
CONTENTS
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Meter Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Meter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Relieve System Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Flushing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Attach Meter to Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attach Nozzle to Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Meter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Manual Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Auto Batch Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Count up and Count Down Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Resettable and Accumulated Totals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Flow Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Low Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Changing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Change Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Verify Firmware Version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Change Unit of Measure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Change Scale Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Save Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Verify Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Calculate Scale Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Absolute Scale Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Chart of Approximate Scale Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AUT-UM-00916-EN-05
Page iii August 2015
Electronic Preset Meter, Model EPM2-ADV-SF, Advanced Series, Special Fluids
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Page iv August 2015
AUT-UM-00916-EN-05
Safety
SAFETY
IMPROPER GROUNDING, POOR VENTILATION, OPEN FLAMES OR SPARKS CAN CAUSE A HAZARDOUS CONDITION AND
RESULT IN AN EXPLOSION OR FIRE AND CAUSE SERIOUS INJURY.
• Be sure the fluid system is properly grounded. See your pump instruction manual for details.
• If there is static sparking or if you feel an electric shock while using the meter, stop dispensing immediately. Identify and
correct the problem before continuing.
• Provide fresh air ventilation. This will avoid the buildup of fumes from the fluid being dispensed.
• Do not smoke while dispensing flammable fluids.
• Keep the dispensing area free of debris including solvents, rags and spilled gasoline.
EQUIPMENT MISUSE CAN CAUSE THE METER TO RUPTURE OR MALFUNCTION AND CAUSE SERIOUS INJURY.
• This equipment is for professional use only.
• Read all instructions, tags and labels before operating the equipment.
• Use the equipment only for its intended purpose.
• Do not modify or alter the equipment.
• Do not leave equipment unattended while dispensing.
• Check equipment daily. Repair or replace worn or damaged parts immediately.
• Do not exceed the maximum working pressure level of the lowest rated system component.
• Use only extensions and nozzles that are designed for use with this equipment.
• Use only fluids and solvents that are compatible with the equipment. Read all fluid and solvent manufacturer’s warnings.
• Tighten all fluid connections before operating this equipment.
• Do not stop or deflect leaks with hands, body, gloves or rags.
• Do not dispense towards any person or any part of the body.
• Do not place hands or fingers over the end of or into the dispense valve.
• Comply with all local, state, and federal fire, electrical and safety regulations
• Use of this product in a manner other than specified in this manual may result in impaired operation or
damage to equipment.
THIS METER IS DESIGNED SPECIFICALLY TO DISPENSE ANTIFREEZE (ETHYLENE GLYCOL) SOLUTION, WINDSHIELD
WIPER FLUID, BRAKE FLUID AND WATER BASED SOLUTION. DO NOT USE FOR PETROLEUM PRODUCTS.
AUT-UM-00916-EN-05
Page 5 August 2015
Meter Buttons
METER BUTTONS
Figure 1: Meter button locations
Used to enter the batch quantity to be dispensed.
LCD DISPLAY
1
Used to display the accumulated total of fluid dispensed as well as the resettable total during
Auto Batch and Manual Mode.
Used to enter and exit the Manual or Auto Batch mode.
• Used in the Manual mode to clear the dispensed quantity.
• Used in the Auto Batch mode to clear the dispensed quantity and reset the meter for the
next batch.
• Used to reset the resettable total dispensed while pressing the TOTAL button.
Used to stop the flow through an Emergency Override.
Table 1: Button descriptions
2
1. Displays Resettable Total, Accumulated Total and Scale
Factor.
2. Displays Unit of Measure.
3. Arrows notify when in Count Up or Count Down.
3
4. Preset batch quantity.
5. History icon.
6. Auto is an indicator of unit being in Auto Batch Mode.
7
Page 6 August 2015
5
6
4
Table 2: LCD display description
7. Low battery icon.
AUT-UM-00916-EN-05
METER INSTALLATION
Relieve System Pressure
THIS EQUIPMENT STAYS PRESSURIZED UNTIL THE PRESSURE IS MANUALLY RELIEVED.
1. Turn o the power supply to the pump or close the shuto valve.
2. Dispense any uid in the system into a waste container by opening the meter.
3. Open all bleed-type master air valves and uid meter in the system.
4. Leave the meter open until ready to pressurize the system.
To reduce the risk of injury from fluid spray from the meter, follow this procedure when you:
• Are instructed to relieve pressure.
• Stop dispensing.
• Check, clean or service any system equipment.
• Clean or install nozzles.
Grounding
Meter Installation
MOVEMENT OF FLUIDS THROUGH THE DISPENSING SYSTEM CREATES STATIC ELECTRICITY. STATIC ELECTRICITY CAN
CAUSE VOLATILE FUMES RESULTING IN AN EXPLOSION AND FIRE. THE DISPENSING SYSTEM MUST BE GROUNDED.
Grounding reduces the risk of static sparking. Ground all system components according to local, state and federal codes.
Consult the pump user manual and other system components to ground the following:
• Pump: follow manufacturer's recommendations
• Air and fluid hoses: use only grounded hoses
• Air compressor: follow manufacturers recommendations
• Fluid supply container: follow the local code
Flushing Procedure
IF THIS INSTALLATION IS NEW OR IF THE FLUID IN THE LINES IS CONTAMINATED, FLUSH THE SYSTEM BEFORE
INSTALLING THE METER(S).
OTE:N If the system has multiple dispense positions, begin at the position farthest from the pump and move towards
the pump.
1. Close uid dispense valves at every position.
2. Once the main uid outlet valve at the pump is closed and the air pressure to the pump motor is properly adjusted, the air
valve is opened.
3. Slowly open the main uid valve.
4. Place the hose end in a waste container. Make sure the hose is secure so no uid leaks during ushing.
5. Slowly open the dispense valve and allow enough uid to pass through it to ensure that the system is clean.
6. Close the valve and repeat for all dispense positions.
AUT-UM-00916-EN-05
Page 7 August 2015
Meter Installation
Attach Meter to Hose
Close the drain valve before starting this procedure.
1. Attach swivel to meter. Apply Loctite® 243 thread sealant, or equivalent, to the male end of the hose. See Figure 2.
Figure 2: Apply thread sealant
2. Insert the metal end of the hose into the swivel. See Figure 3.
Figure 3: Insert hose into swivel
3. Tighten completely with an open ended, adjustable, wrench. See Figure 4.
Figure 4: Use wrench to tighten
OTE:N The threaded end of the meter always has female threads. The metal end of the hose must have male threads. The
inlet and outlet swivel connections are either 1/2" NPT or 1/2" BSPP, depending on meter model.
Attach Nozzle to Meter
1. On the opposite end, apply Loctite® 243 sealant, or equivalent, to the end of the nozzle. Thread the nozzle onto the meter.
See Figure 5.
Figure 5: Thread nozzle onto meter
2. Screw it in tightly with an open-ended, adjustable, wrench. See Figure 6.
Page 8 August 2015
AUT-UM-00916-EN-05
Figure 6: Tighten nozzle with wrench
3. Open all dispense position shuto valves. Start the pump to pressurize the system.
4. Purge all air from the uid lines and dispense valve(s) before use.
METER OPERATION
OTE:N AUTO is used to toggle between Manual Mode and Auto Batch Mode.
Manual Mode
In Manual Mode the meter operates as a free flow-dispensing handle.
Meter Operation
Figure 7: Manual mode screen
1. Pull the trigger to begin the ow.
2. The display shows the amount dispensed.
3. When the correct amount has been dispensed, release the trigger to stop the ow.
4. Press once to reset the counter display to zero.
Auto Batch Mode
To enter Auto Batch Programming Mode, press until a digit and colon appears.
Figure 8: Auto batch mode screen
The meter is now ready to select the desired batch number.
• The ‘0’ is flashing in front of the colon. This is the batch number icon.
• Batch ‘0’ is for Manual Mode. See "Manual Mode".
• Batches ‘1’ through ‘5’ are for auto batching amounts up to 99 units.
• Different batch amounts can be stored in each option.
• Batch ‘6’ is for batches between 1 and 999 units.
1. Press to cycle through the batch number icons to select the desired batch or manual mode.
2. After selecting the correct batch number, change the batch size by pressing , and .
AUT-UM-00916-EN-05
Page 9 August 2015
Meter Operation
Figure 9: Auto batch mode option 1
To batch in options 1…5:
• Press to increase a batch by 10 units.
• Press to increase a batch by 1 unit.
• Press to increase a batch by 0.1 of a unit.
Figure 10: Auto batch mode option 6
To batch in option 6:
• Press to increase a batch amount in increments of 100 units.
• Press to increase a batch amount in increments of 10 units.
• Press to increase a batch amount in increments of 1 unit.
3. After the batch size is selected, press to lock in the batch and dispense uid.
Auto Batch
Auto Icon
Figure 11: Auto batch mode display
Size
4. Pull the trigger to begin the ow. The solenoid valve, in the meter, automatically locks the dispensing valve in the full
open position.
THE METER ALWAYS LOCKS IN THE MAXIMUM OPEN POSITION.
5. Release the trigger, allowing it to fall back.
6. The ow automatically shuts o after the batch quantity has dispensed.
7. After the batch quantity has been dispensed the meter is a free ow-dispensing handle until the reset button is depressed.
OTE:N In case of an emergency or to interrupt a batch, the meter is equipped with an Emergency Override. See "Emergency
Override" on page 12.
8. The user has the option to top o the uid at the end of a batch. To top off the fluid, pull the trigger to begin the flow and
release it when the desired amount has been pumped.
9. Press when nished. The display resets and the meter is now ready to dispense the next batch.
Page 10 August 2015
AUT-UM-00916-EN-05
Meter Operation
Count up and Count Down Modes
In Count Up Mode the meter counts up to the pre-programmed batch amount. In Count Down Mode the meter counts from
the programmed batch amount down to zero.
OTE:N Batch number 3 is always in Count Down Mode.
1. When in the Auto Batch Programming Mode, press and the count up/count down arrows ash in the display.
Figure 12: Display for count up and count down modes
• Press to toggle between Count Up and Count Down.
• Press to select Count Up or Count Down.
2. Press to lock in the batch quantity when batch size is selected. The screen will ash and the batch number icon will
not appear on the display.
Figure 13: Batch quantity size in count up and count down modes
• If the meter is in Count Up Mode, the display shows zeroes.
• If the meter is in the Count Down Mode, the selected batch size is displayed.
AUT-UM-00916-EN-05
Page 11 August 2015
Operating Mode Functions
OPERATING MODE FUNCTIONS
These functions operate the same in Manual Mode and Auto Batch Mode.
Resettable and Accumulated Totals
The meter has two flow totalizers, Resettable Total and Accumulated Total.
1. Press and hold to display Accumulated Total, after holding for three seconds the display changes to
Resettable Total.
2. Resettotal displays the total uid dispensed since the Resettable Total was last set back to zero.
Figure 14: Resettable total display
3. Press while viewing Resettotal to set it back to zero.
4. Release to return to the operating screen.
OTE:N The Accumulated Total cannot be reset unless the user changes from English units to metric units or from metric to
English units. See "Change Unit of Measure" on page 14.
Emergency Override
In case of an emergency or to interrupt a batch, the meter is equipped with an Emergency Override which closes the valve,
immediately stopping fluid flow.
1. Press to activate the Emergency Override.
2. After an Emergency Override, batching can continue by pulling up on the trigger.
History
This option allows the user to review the previous five batches dispensed with the meter.
Figure 15: History display
1. Press and hold to view he ve previous batches.
a. The batches are displayed on screen, one at a time; beginning with the most recent and cycling through to the oldest.
The batches will continue to cycle until the button is released.
2. The display automatically returns to the normal operating screen two seconds after the button is released.
OTE:N The history cannot be erased unless the user changes from English to metric or from metric to English units. See
"Change Unit of Measure" on page 14.
Flow Rate
This option allows a user to see instantaneously the rate at which fluid is flowing through the meter.
Figure 16: Flow rate display
Press and hold while fluid is flowing through the meter. The Flow Rate will appear in the bottom right hand corner of
the display. The Flow Rate will remain on the screen until the button is released. Releasing the button returns the display to
the normal operating screen.
OTE:N The Flow Rate can only be displayed if fluid is flowing through the meter.
Page 12 August 2015
AUT-UM-00916-EN-05
Service
Error Codes
The meter has one error code that may display:
SF0 (Scale Factor 0) The Scale Factor setting for the meter is set to 0.000.
The code provides an indication, at the meter, that there is an error in communication between the meter and keypad. To
correct the error, input a valid Scale Factor for the meter follow the instructions in "Change Factory Settings" on page 14. All
other error codes are for factory purposes only. To clear the meter, press .
SERVICE
Low Battery
When the batteries need to be changed a progression of warnings appears on the meter screen. First, the Low Battery icon will
appear on the display, this means that the batteries are getting low, and should be changed. When the icon begins to flash,
the battery power is too low, and meter functions are disabled.
Low Battery
Icon
Figure 17: Low battery icon
Changing the Batteries
The battery compartment is located in the lower case on the underside of the trigger guard.
1. Turn the unit face down.
2. Unscrew the two screws. Remove the battery door to expose the batteries.
Figure 18: Replacing the batteries
3. Replace the old batteries. The meter takes four AA, alkaline, batteries.
4. Dispose of used batteries properly, according to local regulations.
OTE:N Changing the batteries does not affect any of the programmed values or totals.
AUT-UM-00916-EN-05
Page 13 August 2015
Change Factory Settings
CHANGE FACTORY SETTINGS
Each meter is calibrated at the factory for use with motor oil. See "Change Scale Factor" on page 15. The Unit of Measure is
also selected prior to shipment.
Verify Firmware Version
The firmware version and code checksum are displayed by pressing and holding and simultaneously. The last
two digits on the lower right are the firmware version. Meters with version 17 or higher use the procedure outlined in this
manual for changing the unit of measure, scale factor and enabling or disabling the EPM functionality.
Programming
1. Press and hold and simultaneously. PrG will appear on the display.
Figure 19: Entering programming mode
2. Release the buttons.
3. Press and release these buttons in order: , , , , and .
4. The current unit of measure will now be ashing indicating that you have entered the programming mode.
Change Unit of Measure
The meter comes with an option to choose four different units of measure.
Scale Factor
Digits
Unit of Measure
Figure 20: Unit of measure display
1. The current unit of measure will ash when Programming Mode is entered.
2. Press to toggle amongst the four options; PT, QT, GAL, L.
3. When the correct unit of measure is displayed, press to select it. The unit of measure will stop ashing.
4. If L (liters) is selected, the decimal point will being to ash. The decimal point can either be changed to a comma or a
period. To do this press .
5. If no scale factor changes are necessary, see "Save Changes" on page 15.
CHANGING THE UNIT OF MEASUREMENT FROM METRIC TO ENGLISH OR FROM ENGLISH TO METRIC CLEARS THE
RESETTABLE TOTAL AND ACCUMULATED TOTAL.
Page 14 August 2015
AUT-UM-00916-EN-05
Calculate Scale Factor
Change Scale Factor
CHANGING THE SCALE FACTOR CHANGES THE ACCURACY OF THE METER, POTENTIALLY CAUSING IT TO OVERFILL OR
UNDER FILL. THIS HAS THE POTENTIAL TO CAUSE A MECHANICAL BREAKDOWN.
Scale factor digits
Figure 21: Scale factor display
1. Press to advance through the scale factor digits.
2. To change the selected number, press .
OTE:N All digits can be scrolled between 0 and 9 except the first. It can only be toggled from 0 to 1 or from 1 to 0.
3. Press to advance to the next digit in the scale factor.
4. Repeat steps 2 and 3 for all ve digits.
Save Changes
To save changes and exit programming mode:
1. Press and hold and simultaneously.
2. The display will ash three times and go blank.
3. Press and the display will turn back on.
Verify Changes
1. Verify unit of measure is correct.
2. Press and hold and simultaneously to verify the scale factor is correct.
CALCULATE SCALE FACTOR
A Scale Factor is a number used to adjust meter accuracy. The Scale Factor is set at the factory using motor oil with a viscosity
of 10W. The primary use for Scale Factor recalibration is to batch fluids with different viscosities. If the fluid has a lower
viscosity, more fluid can slip past the meter gears without being detected. Changing the Scale Factor adjusts the meter to
compensate for the loss. The meter multiplies each pulse by the Scale Factor number to correct the accuracy when it converts
to the specified units. For an approximate Scale Factor for fluids of different viscosities, see "Chart of Approximate Scale Factors"
on page 16.
OTE:N The meter’s original Scale Factor was written on the trigger when it was calibrated at the factory. It may have been
revised after field installation. Use the Scale Factor showing on the display, not on the trigger.
CHANGING THE SCALE FACTOR WILL CHANGE THE ACCURACY OF THE METER, POTENTIALLY CAUSING IT TO OVERFILL
OR UNDER FILL. THIS HAS THE POTENTIAL TO CAUSE A MECHANICAL BREAKDOWN.
To view the current scale factor, press and hold and simultaneously.
AUT-UM-00916-EN-05
Page 15 August 2015
Calculate Scale Factor
Absolute Scale Factor
For absolute scale factor, preform this test:
1. Run a measured amount of uid through the meter.
2. If the meter delivers 4.20 quarts and the display shows only 4.00 quarts, then the Scale Factor needs to be adjusted.
3. Divide what the meter delivered (4.20) by what the display shows (4.00). You get an error factor of (1.05).
4. The existing Scale Factor is 1.0123, as shown in steps 1 and 2 in "Verify Changes" on page 15.
5. To calculate a new factor: 1.0123 (existing Scale Factor) x 1.05 (error factor) = 1.0629 (new Scale Factor).
6. Enter that number as described in the "Change Scale Factor" on page 15.
OTE:N Use the Scale Factor shown on the display, not on the trigger.
Chart of Approximate Scale Factors
Figure 22: Scale factors for fluids with different viscosities
Fluid Viscosity Scale Factor
Water/anti-freeze 5 1.044
Anti-freeze 18 1.007
Brake Fluid 42 1.004
ATF 80 1.002
10W 140 1.000
80W-90 450 0.999
140W 1800 0.993
Table 3: Fluid viscosity and scale factors
Page 16 August 2015
AUT-UM-00916-EN-05
DIMENSIONS
Dimensions
11.3 in. (287.02 mm)
4.3 in. (109.22 mm)
7.0 in. (177.8 mm)
Figure 23: Meter Dimensions
SPECIFICATIONS
Maximum Flow * 10 gpm (38 lpm)
Minimum Flow * 0.25 gpm (1 lpm)
Operating Pressure (Maximum) 1000 psi (67 bar)
Operating Pressure (Minimum) 5 psi (0.35 bar)
Operating Temperature (Maximum) 120° F (50° C)
Operating Temperature (Minimum) 20° F (-5° C)
Accuracy (General) +/- 0.5%
Accuracy (Anti-Freeze) +/- 1.5%
5-Digit LCD Display Quarts, Pints, Gallons, Liters
Inlet and Outlet Connections 1/2" NPT (1/2" BSPP)
* Minimum and maximum flow range will vary with fluid viscosity
Table 4: Meter specifications
AUT-UM-00916-EN-05
Page 17 August 2015
Parts
PARTS
Figure 24: Parts: back of meter
Item Description Part Number
1 Battery holder assembly 64103-026
2 Bottom case with screws 64103-003
Table 5: Part numbers: back of meter
1
2
Figure 25: Parts: front of meter
Item Description Part Number
1 Display assembly 64103-023
2 EPM2 adv. register assembly 64103-025
Not shown Swivel, NPT, special fluids 64082-003
Not shown Rubber boot 65546-001
Table 6: Part numbers: front of meter
Page 18 August 2015
AUT-UM-00916-EN-05
2
1
3
Figure 26: Parts: inside meter
Item Description Part Number
1 Valve assembly 64103-011
2 Gear service kit with O-ring 62896-003
3 Trigger Assembly 64103-005
Table 7: Part numbers: inside meter
Parts
AUT-UM-00916-EN-05
Page 19 August 2015
Electronic Preset Meter, Model EPM2-ADV-SF, Advanced Series, Special Fluids
TROUBLESHOOTING
RELIEVE THE PRESSURE PRIOR TO CHECKING OR REPAIRING THE METER. MAKE SURE ALL VALVES, CONTROLS AND
PUMPS ARE OPERATING CORRECTLY.
Symptom Possible Cause Remedy
Battery icon is displayed Batteries are low Replace batteries
Meter asleep
Display blank
Loose battery connection
Batteries dead
Meter not in Auto Mode
Meter does not latch for batching
Meter not reset after prior batch
Low batteries
Filter is clogged Clean or replace the filter in the swivel nut
Slow or no fluid flow
Pump pressure is low Turn up the pump pressure
Foreign material is jamming meter Contact your local distributor for repair
Meter inaccurate Scale Factor not correct for fluid
Batch overruns program value Pulse delay value set too low
Press
Remove battery pack and check battery
connection / press
Replace batteries / press
Press and program batch size
Press
Check for battery icon / replace batteries /
press
Enter Program Mode, check and reset
the Scale Factor
Enter Program Mode, reset the pulse delay
to a higher value
Control. Manage. Optimize.
Trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and enhancements, Badger Meter reserves
the right to change product or system specications without notice, except to the extent an outstanding contractual obligation exists. © 2015 Badger Meter, Inc. All rights reserved.
www.badgermeter.com
The Americas | Badger Meter | 4545 West Brown Deer Rd | PO Box 245036 | Milwaukee, WI 53224-9536 | 800-876-3837 | 414-355-0400
México | Badger Meter de las Americas, S.A. de C.V. | Pedro Luis Ogazón N°32 | Esq. Angelina N°24 | Colonia Guadalupe Inn | CP 01050 | México, DF | México | +52-55-5662-0882
Europe, Middle East and Africa | Badger Meter Europa GmbH | Nurtinger Str 76 | 72639 Neuen | Germany | +49-7025-9208-0
Europe, Middle East Branch Oce | Badger Meter Europe | PO Box 341442 | Dubai Silicon Oasis, Head Quarter Building, Wing C, Oce #C209 | Dubai / UAE | +971-4-371 2503
Czech Republic | Badger Meter Czech Republic s.r.o. | Maříkova 2082/26 | 621 00 Brno, Czech Republic | +420-5-41420411
Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | +421-2-44 63 83 01
Asia Pacic | Badger Meter | 80 Marine Parade Rd | 21-04 Parkway Parade | Singapore 449269 | +65-63464836
China | Badger Meter | 7-1202 | 99 Hangzhong Road | Minhang District | Shanghai | China 201101 | +86-21-5763 5412 Legacy Document Number: IOM-173-03-EN 53400-173
Loading...