Baby Jogger CAR SEAT ADAPTER KIT User Manual

Car Seat

Adapter Kit

For Use With:

• City-Single Stroller

• Q-Single Stroller

• Pram Accessory

Read these

instructions carefully

before use and

keep them for

future reference.

Your child’s safety may be

affected if you do not follow

these instructions.

Kit Includes

U-Shaped Support Bar

This will be used to install Peg Perego Primo Viaggio SIP, Graco, Evenflo, and Britax Companion car seats.

This Adapter Kit Includes:

1 – U-Shaped Support Bar

1 – T-Shaped Support Bar

1 – Spring Support Bar

1 – Straight Support Bar

2 – Adapter Brackets (1 – left, 1 – right)

T-Shaped Support Bar

This will be used to install only Britax Companion car seats.

Spring Support Bar

This will be used to install only Peg Perego Primo Viaggio SIP.

Straight Support Bar

This will be used to install only Peg Perego Primo Viaggio SIP.

Adapter Brackets

These will be used to install the Pram, Peg Perego Primo Viaggio SIP, Graco, Evenflo, Britax Companion, and Maxi Cosi car seats.

Pram

To install the Pram you will need the following adapter part(s):

2 – Adapter Brackets (1 – left, 1 – right)

1. Remove the canopy and seat from stroller frame.

Please refer to the owner manual. (Be sure to store fabric and hardware for later use.)

2. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. (Fig. A) Repeat to the left side.(Fig. B)

(Fig. A)

(Fig. B)

Note: Do not over tighten. Over tightening will damage

the product and void the warranty.

3. Place Pram onto Adapter Brackets, making sure child will be facing toward stroller handle. Firmly press down on the Pram until you hear a click which means it’s locked in place. (Fig. C)

Note: The Red compression locks and the support bars are

not applicable when using the Baby Jogger Pram

4. To remove Pram from the Adapter Brackets, press the two buttons on the Pram handle and lift up carefully.

5. To retract canopy, push button on canopy hinge and push canopy back out of the way. To use canopy in the extended position, push button and pull canopy forward.

Note: To avoid safety belt strap catching on wheels, secure them

to each other in order to avoid hanging.

(Fig. C)

1

Peg Perego Primo Viaggio SIP

To install the Peg Perego Primo Viaggio SIP you will need the following part(s):

2 – Adapter Brackets (1 – left, 1 – right)

1 – U-Shaped Support Bar

1 – Spring Support Bar

1 – Straight Support Bar

1. Remove the canopy and seat from stroller frame. Please refer to the

owner manual. (Be sure to store fabric and hardware for later use.)

2. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. (Fig. A) Repeat to the left side. (Fig. B)

Note: Do not over tighten. Over tightening will damage the product

and void the warranty.

3. Before tightening Left Adapter Bracket to frame, align the Straight Support Bar into Adapter Bracket hole. (Fig. B) Once in place tighten Left Adapter Bracket. (Fig. B)

4. Open the compression locks by flipping the Red Latches up to allow U-Shape Support Bar to be inserted into Adapter Brackets. (Fig. C)

5. Insert the U-Shaped Support Bar with the curved end pointing down into the Adapter Brackets.

6. Insert Spring Support Bar into front of U-Shaped Support Bar

by squeezing in. (Fig. E)

7. Place the car seat onto the U-Shape Support Bar making sure that the Spring and Straight Support Bars engage the locking mechanisms on the Peg Perego car seat. Adjust U-Shape Support Bar to proper length by sliding U-Shape Support Bar in and out. Use car seat to ensure proper distance. (Fig. C) Close compression locks by flipping the Red latches down. (Fig. D)

8. Secure the car seat to stroller using Safety Belt. (Fig. F)

2

(Fig. A)

(Fig. D)

(Fig. B)

(Fig. C)

(Fig. E)

(Fig. F)

3

Graco/Evenflo Car Seat

To install a Graco/ Evenflo car seat you will need the following adapter part(s):

2 – Adapter Brackets (1 – left, 1 – right)

1 – U-Shaped Support Bar

1. Remove the canopy and seat from stroller frame. Please refer to the

owner manual. (Be sure to store fabric and hardware for later use.)

2. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. (Fig. A) Repeat to the left side. (Fig. B)

Note: Do not over tighten. Over tightening will damage the product

and void the warranty.

3. Open the compression locks by flipping the Red Latches up to allow U-Shape Support Bar to be inserted into Adapter

Brackets. (Fig. C)

4. Insert the U-Shaped Support Bar with the curved end pointing up into the Adapter Brackets. (Fig. D)

5. Place car seat onto U-Shaped Support Bar. Adjust U-Shape Support Bar to proper length by sliding frame in and out. Use car

seat to insure proper distance. Close compression locks by flipping the red latches down. (Fig. E)

6. Secure the car seat to stroller using Safety Belt. (Fig. F)

Note: The Straight and Spring Support Bars are not applicable when

using a Graco or Evenflo car seat.

4

(Fig. A)

(Fig. D)

(Fig. B)

(Fig. C)

(Fig. E)

(Fig. F)

5

Britax Companion Car Seat

To install the Britax Companion car seat you will need the following adapter part(s):

2 – Adapter Brackets (1 – left, 1 – right)

1 – U-Shaped Support Bar

1 – T-Shaped Support Bar

1. Remove the canopy and seat from stroller frame. Please refer to the

owner manual. (Be sure to store fabric and hardware for later use.)

2. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. (Fig. A) Repeat to the left side. (Fig. B)

Note: Do not over tighten. Over tightening will damage the product

and void the warranty.

3. Open compression locks by flipping the red latches up. (Fig. B)

4. Insert the U-Shaped Support Bar with the curved end pointing up into Adapter Brackets. (Fig. D)

5. Place car seat onto U-Shaped Support Bar. Adjust U-Shape Support Bar to proper length by sliding frame in and out.

Use car seat to insure proper distance. Close compression locks by flipping the red latches down. (Fig. E)

6. Place the T-Bar onto car seat as shown and tighten strap using D-Ring and Velcro. (Fig. F)

7. Secure the car seat to stroller using Safety Belt.

Note: The Straight Support Bar is not applicable when using the

Britax Companion car seat.

6

(Fig. A)

(Fig. D)

(Fig. B)

(Fig. C)

(Fig. E)

(Fig. F)

7

Maxi Cosi Car Seat

To install the Maxi Cosi car seat you will need the following adapter part(s):

2 – Adapter Brackets (1 – left, 1 – right)

1. Remove the canopy and seat from stroller frame. Please refer to the

owner manual. (Be sure to store fabric and hardware for later use.)

2. Secure Right Adapter Bracket to frame directly below the folding mechanism making sure to align the notches in the Adapter Bracket over the snap and rivets. (Fig. A) Repeat to the left side.(Fig. B)

Note: Do not over tighten. Over tightening will damage the product

and void the warranty.

3. Place car seat onto the Adapter Brackets, making sure the child will be facing toward stroller handle. Firmly press down on the car seat to lock into place. (Fig. C)

4. Secure the car seat to stroller using Safety Belt. (Fig. D)

Note: The red compression locks and support bars are not applicable

when using the Maxi Cosi car seat.

8

(Fig. A)

(Fig. C)

(Fig. B)

(Fig. D)

9

Thank You!

Our #1 goal is to make sure you are happy with

our product. If you have any comments or

suggestions, we would love to hear from you.

1.800.241.1848

CustomerService@babyjogger.com

Baby Jogger is a Division of Dynamic Brands

8575 Magellan Parkway, Suite 1000 • Richmond, VA 23227

T: 800.241.1848 • F: 804.262.6277

www.babyjogger.com

BJC CSA 6.20.06