Axis P5532-E User Manual
INSTALLATION GUIDE
AXIS P5532-E PTZ Dome Network Camera
AXIS P5534-E PTZ Dome Network Camera
ENGLISH DEUTSCH
FRAN
Ç
AIS
ITALIANO
ESPAÑOL
Legal Considerations
Video and audio surveillance can be prohibited by laws
that vary from country to country. Check the laws in
your local region before using this product for
surveillance purposes.
This product includes one (1) H.264 decoder license. To
purchase further licenses, contact your reseller.
Trademark Acknowledgments
Apple, Boa, Bonjour, Ethernet, Internet Explorer, Linux,
Microsoft, Mozilla, Netscape Navigator, OS/2, Real,
SMPTE, QuickTime, UNIX, Windows, WWW are
registered trademarks of the respective holders. Java
and all Java-based trademarks and logos are trademarks
or registered trademarks of Sun Microsystems, Inc. in
the United States and other countries. Axis
Communications AB is independent of Sun
Microsystems Inc. UPnP™ is a certification mark of the
UPnP™ Implementers Corporation.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate
the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment to
an outlet on a different circuit to the receiver. Consult
your dealer or an experienced radio/TV technician for
help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards.
USA - This equipment has been tested and found to
comply with the limits for a Class B computing device
pursuant to Subpart B of Part 15 of FCC rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user at his/her own expense will be required to
take whatever measures may be required to correct the
interference.
Canada - This Class B digital apparatus complies with
Canadian ICES-003.
Europe - This digital equipment fulfills the
requirements for radiated emission according to limit B
of EN55022, and the requirements for immunity
according to EN55024 residential and commercial
industry.
Japan - This is a class B product based on the standard
of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Australia - This electronic device meets the
requirements of the Radio communications
(Electromagnetic Compatibility) Standard AS/NZS
CISPR22:2002.
Korea - Class B: As this equipment has obtained EMC
registration for household use, it can be used in any area
including residential areas.
Safety
Complies to EN 60950-1 (IEC 60950-1), Safety of
Information Technology Equipment.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no
user-serviceable components. Unauthorized equipment
changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
RoHS
This product complies with both the European
RoHS directive, 2002/95/EC, and the Chinese
RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE Directive). This directive is
applicable in the European Union member
states. The WEEE marking on this product (see right) or
its documentation indicates that the product must not
be disposed of together with household waste. To
prevent possible harm to human health and/or the
environment, the product must be disposed of in an
approved and environmentally safe recycling process.
For further information on how to dispose of this
product correctly, contact the product supplier, or the
local authority responsible for waste disposal in your
area. Business users should contact the product supplier
for information on how to dispose of this product
correctly. This product should not be mixed with other
commercial waste.
Support
Should you require any technical assistance, please
contact your Axis reseller. If your questions cannot be
answered immediately, your reseller will forward your
queries through the appropriate channels to ensure a
rapid response. If you are connected to the Internet, you
can:
• download user documentation and firmware updates
• find answers to resolved problems in the FAQ
database. Search by product, category, or phrases
• report problems to Axis support by logging in to your
private support area
Safeguards
Please read through this Installation Guide carefully before installing the product. Keep the Installation Guide
for further reference.
CAUTION!
• When transporting the Axis product, use the original packaging or equivalent to prevent damage to the
product.
• Avoid exposing the Axis product to vibration, shocks or heavy pressure and do not install the camera on
unstable brackets, unstable or vibrating surfaces or walls, since this could cause damage to the product.
• Only use handtools when installing the Axis product, the use of electrical tools or excessive force could
cause damage to the product.
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.
• Only use accessories and spare parts provided or recommended by Axis.
• Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for service matters.
IMPORTANT!
• This Axis product must be used in compliance with local laws and regulations.
Battery replacement
This Axis product uses a 3.0V CR2032 Lithium battery as the power supply for its internal real-time clock (RTC).
Under normal conditions this battery will last for a minimum of 5 years. Low battery power affects the
operation of the RTC, causing it to reset at every power-up. A log message will appear when the battery needs
replacing. The battery should not be replaced unless required!
If the battery does need replacing, please contact www.axis.com/techsup for assistance.
• Danger of Explosion if battery is incorrectly replaced.
• Replace only with the same or equivalent battery, as recommended by the manufacturer.
• Dispose of used batteries according to the manufacturer's instructions.
ENGLISH
Cleaning of dome cover
• Be careful not to scratch or damage the dome cover. Do not clean a dome cover that looks clean to the eye
and never polish the surface. Excessive cleaning can damage the surface.
• For general cleaning of a dome cover it is recommended to use a non-abrasive, solvent-free neutral soap or
detergent with water and a soft cloth. Rinse well with clean lukewarm water. Dry with a soft cloth to prevent water spotting.
• Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning in direct sunlight or at
elevated temperatures.
AXIS P5532-E/AXIS P5534-E Installation Guide Page 5
Important!
This product must be used in
compliance with local laws and
regulations.
AXIS P5532-E/AXIS P5534-E
Installation Guide
This installation guide provides instructions for installing an AXIS P5532-E/AXIS P5534-E PTZ Dome
Network Camera on your network. For all other aspects of using the product, please see the User’s
Manual, available on the CD included in this package, or from www.axis.com
Installation steps
1. Check the package contents against the list below.
2. Hardware overview. See page 6.
3. Install the hardware. See page 7.
4. Assign an IP address. See page 11.
5. Set the password. See page 14.
Package contents
Item Models/variants/notes
Network camera AXIS P5532-E/AXIS P5534-E 60Hz/50Hz
Dome covers Clear transparent cover (pre-mounted)
Smoked transparent cover
High PoE Midspan AXIS T8123 including power cable (country specific)
RJ45 connector IP66 rated network connector
Sunshield Plastic protective cover, including screws
CD AXIS Network Video Product CD, including product documentation,
installation tools and other software
Printed materials AXIS P5532-E Installation Guide (this document)
Axis Warranty Document
Extra serial number labels (2x)
ENGLISH
Optional accessories AXIS T91A Mounting Accessories
See www.axis.com for information on available accessories
Page 6 AXIS P5532-E/AXIS P5534-E Installation Guide
Unit holders (3)
Network connector (PoE)
Hook for safety wire
Sunshield
Screws (3)
Dome cover
Part number (P/N) & Serial number (S/N).
The serial number may be required
during the installation.
SDHC card slot
Status indicator LED
Restart button
Control button
Dome ring
Dome coverScrews (6)
Top cover
Sealing ring
Top cover
screws (4)
Hardware overview
AXIS P5532-E/AXIS P5534-E Installation Guide Page 7
Protective packaging
Install the hardware
Prepare for installation
Read all the instructions before preparing to install the network camera since several installation
preparation steps require removing the top cover and would benefit from being completed together.
The sunshield must be removed to install/remove an SD card, see
page 8.
• Follow the instructions
packing before installing the camera.
• The network camera is supplied with a clear transparent cover and a smoked transparent
cover. If required, follow the instructions
below to replace the dome cover.
• A standard or high capacity SD card (not included) is required to store images locally in the
network camera. Follow the instructions
dome cover and install an SD card.
Remove the protective packaging
Replace the clear/smoked dome cover (optional)
Install an SD card (optional)
Remove the protective packaging
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 6.
2. Remove the protective packaging.
Install an SD card (optional),
, below to remove the protective
, below to remove the
on
ENGLISH
,
3. If replacing the clear/smoked dome cover or installing an SD card, refer to the instructions
Replace the clear/smoked dome cover (optional)
4. Put the top cover back in its original position and fasten the screws.
and
Install an SD card (optional),
on page 8.
Page 8 AXIS P5532-E/AXIS P5534-E Installation Guide
Replace the clear/smoked dome cover (optional)
IMPORTANT!
!
This camera has a dehumidifying membrane to maintain low humidity levels inside the dome. To
avoid condensation, do not disassemble the camera in rain or in damp conditions.
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 6.
2. Remove the 6 dome ring screws and remove the dome ring from the top cover.
3. Attach the dome ring and the replacement dome cover to the top cover and secure by
tightening the 6 screws.
4. If installing an SD card, refer to the instructions
5. Put the top cover back in its original position and fasten the screws.
Note:
Be careful not to scratch or damage the dome cover. If possible, keep the protective plastic
on the dome cover until the installation is complete.
Install an SD card (optional)
, below.
Install an SD card (optional)
1. Remove the sunshield, see illustration on page 6.
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 6.
2. Insert an SD card (not included) into the SDHC (Secure Digital High Capacity) card slot.
3. Put the top cover back in its original position and fasten the screws.
4. Put the sunshield back in its original position and fasten the screws.
Note:
The SD card is automatically mounted when inserted into the SDHC card slot. However,
before removing the SD card it should be unmounted through the camera’s web pages. Go
to Setup > System Options > Storage > SD Card and click Unmount. For more
information, please see the User’s Manual available from the AXIS Network Video Product
CD supplied with this product or from the website at www.axis.com
AXIS P5532-E/AXIS P5534-E Installation Guide Page 9
Wall bracket (mounting example, bracket not included)
Safety
wire
Slots for
Screws
Torx T30
unit holders
Install the network camera
IMPORTANT!
!
The supplied RJ45 connector or a compatible, IP66 rated RJ45 connector must be used in order to
comply with the IP66 rated design of the camera.
1. Install the selected bracket (not included)
according to the instructions supplied with the
bracket. If drilling is required, make sure to use
drill bits, screws, and plugs that are appropriate
for the material. See www.axis.com for information on available mounting accessories.
2. Route the network cable and attach the
supplied RJ45 connector. Refer to the
instructions provided with the connector for
information on wiring and assembly.
3. Hook the camera to the safety wire on the
bracket.
4. Connect the network cable and RJ45 connector to the network connector on the camera.
5. Install AXIS T8123, see
6. Check that the indicator LEDs on the midspan indicate the correct conditions, see the table on
page 11 for further details.
7. Slide the unit holders on the camera into the slots on the bracket and rotate the camera unit.
8. Secure the network camera to the mounting bracket by fastening the 3 screws (Torx T30).
Install AXIS T8123 High PoE Midspan 1-port,
on page 10.
ENGLISH
Page 10 AXIS P5532-E/AXIS P5534-E Installation Guide
Ethernet
Data &
Data in
Port
indicator
AC Input
indicator
Power out
Network camera
connectivity
connectivity
AXIS T8123
Install AXIS T8123 High PoE Midspan 1-port
Axis T8123 High PoE Midspan enables Axis network video products with high power consumption
to receive data and power over the same Ethernet cable. Follow these instructions to connect
AXIS T8123.
Note:
Axis can only guarantee full functionality with the AXIS T8123, no other High PoE devices
are supported.
1. Connect the AXIS T8123 (Data in) to the network switch using a standard network cable.
2. Connect the AXIS T8123 (Data and Power Out) to the network camera, using the network cable
that has been connected to the camera.
3. Connect the AXIS T8123 to an AC outlet (100-240 VAC), using the supplied power cable.
For information on the LEDs on the midspan, see
Assign an IP address,
on page 11.
AXIS P5532-E/AXIS P5534-E Installation Guide Page 11
Assign an IP address
Most networks today have a DHCP server that automatically assigns IP addresses to connected
devices. If your network does not have a DHCP server the network camera will use 192.168.0.90 as
the default IP address.
If you would like to assign a static IP address, the recommended method in Windows is either AXIS
IP Utility or AXIS Camera Management. Depending on the number of cameras you wish to install,
use the method that best suits your purpose.
Both of these free applications are available on the Axis Network Video Product CD supplied with
this product, or they can be downloaded from www.axis.com
Method Recommended for Operating system
AXIS IP Utility
See page 12
AXIS Camera Management
See page 13
Notes:
• If assigning the IP address fails, check that there is no firewall blocking the operation.
• For other methods of assigning or discovering the IP address, e.g. in other operating systems, see
page 16.
Single camera
Small installations
Multiple cameras
Large installations
Installation on a different subnet
Windows
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista
Windows 7
ENGLISH
Page 12 AXIS P5532-E/AXIS P5534-E Installation Guide
AXIS IP Utility - single camera/small installation
AXIS IP Utility automatically discovers and displays Axis devices on your network. The application
can also be used to manually assign a static IP address.
Note that the computer running AXIS IP Utility must be on the same network segment (physical
subnet) as the network camera.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS IP Utility.
3. When the camera appears in the window, double-click it to open its home page.
4. See page 14 for instructions on how to assign the password.
Assign the IP address manually (optional)
1. Acquire an unused IP address on the same network segment as your computer.
2. Select the network camera in the list.
3. Click the Assign new IP address to the selected device button and enter the IP address.
4. Click Assign and follow the on-screen instructions. Note that the camera must be restarted
within 2 minutes for the new IP address to be set.
5. Click Home Page to access the camera’s web pages.
6. See page 14 for instructions on how to set the password.
AXIS P5532-E/AXIS P5534-E Installation Guide Page 13
AXIS Camera Management - multiple cameras/large installations
AXIS Camera Management can automatically discover multiple Axis devices, show connection
status, manage firmware upgrades and set IP addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS Camera Management. When the network camera appears in the window, right-click
the link and select Live View Home Page.
3. See page 14 for instructions on how to set the password.
Assign an IP address in a single device
1. Select network camera in AXIS Camera Management and click
the Assign IP button .
2. Select Assign the following IP address and enter the IP
address, subnet mask and default router the device will use.
3. OK.
ENGLISH
Assign IP addresses in multiple devices
AXIS Camera Management speeds up the process of assigning IP
addresses to multiple devices, by suggesting IP addresses from a
specified range.
1. Select the devices you wish to configure (different models can
be selected) and click the Assign IP button .
2. Select Assign the following IP address range and enter the
range of IP addresses, the subnet mask and default router the
devices will use.
3. Click Update. Suggested IP addresses are listed under New IP Addresses and can be edited by
selecting a device and clicking Edit.
4. Click OK.
Page 14 AXIS P5532-E/AXIS P5534-E Installation Guide
To configure the password directly
via an unencrypted connection, enter
the password here.
To create an HTTPS connection,
start by clicking this button.
Set the password
To gain access to the product, the password for the default administrator user root must be set. This
is done in the ‘Configure Root Password’ dialog, which is displayed when the network is accessed
for the first time.
To prevent network eavesdropping when setting the root password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate.
Note: HTTPS (Hypertext Transfer Protocol over Secure Socket Layer) is a protocol used to encrypt
the traffic between web browsers and servers. The HTTPS certificate controls the encrypted
exchange of information.
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below.
To set the password via an encrypted HTTPS connection, follow these steps:
1. Click the Create self-signed certificate button.
2. Provide the requested information and click OK. The certificate is created and the password can
now be set securely. All traffic to and from the network camera is encrypted from this point on.
3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now
been configured.
4. To log in, enter the user name “root” in the dialog as requested
Note: The default administrator user name root cannot be deleted.
5. Enter the password as set above, and click OK.
Note: If the password is lost, the camera must be reset to the factory default settings. See
page 19.
AXIS P5532-E/AXIS P5534-E Installation Guide Page 15
Setup - Provides all the
tools for configuring the
camera to requirements.
Help - Displays
online help on all
aspects of using
the camera.
Access the video stream
The Live View page of the network camera is displayed, with links to the Setup tools, which allow
you to customize the camera.
If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream
in Internet Explorer. You will need administrator rights on the computer to do this.
If required, click the link to install missing decoders.
Note:
To install AMC in Windows Vista, you must run Internet Explorer as administrator. Rightclick the Internet Explorer icon and select Run as administrator.
ENGLISH
Page 16 AXIS P5532-E/AXIS P5534-E Installation Guide
Other methods of setting the IP address
The table below shows the other methods available for setting or discovering the IP address. All
methods are enabled by default, and all can be disabled.
UPnP™
Bonjour
AXIS Dynamic DNS
Service
ARP/Ping
DHCP server
Use in operating
system
Windows When enabled on your computer, the camera is automatically
MAC OSX
(10.4 or later)
All A free service from Axis that allows you to quickly and simply
All See below. The command must be issued within 2 minutes of
All To view the admin pages for the network DHCP server, see the
Notes
detected and added to “My Network Places.”
Applicable to browsers with support for Bonjour. Navigate to the
Bonjour bookmark in your browser (e.g. Safari) and click on the
link to access the camera’s web pages.
install your camera. Requires an Internet connection with no
HTTP proxy. See www.axiscam.net for more information.
connecting power to the camera.
server’s own documentation.
AXIS Video Hosting System (AVHS)
The camera can also be connected to an AVHS service for hosted video. If you have subscribed to an
AVHS service, follow the instructions in the Service Provider’s Installation Guide. For more
information and help to find a local AVHS Service Provider, go to www.axis.com/hosting
The Camera owner authentication key is found on the back cover of this document. The key is
associated with the camera’s unique serial number (S/N) as shown on the top of the label.
Note:
Save the key for future reference.
AXIS P5532-E/AXIS P5534-E Installation Guide Page 17
Set the IP address with ARP/Ping
1. Acquire an IP address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the product label on the camera.
3. Open a command prompt on your computer and enter the following commands:
Windows syntax: Windows example:
arp -s <IP Address> <Serial Number>
ping -l 408 -t <IP Address>
UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:
arp -s <IP Address> <Serial Number> temp
ping -s 408 <IP Address>
4. Check that the network cable is connected to the camera and then start/restart the camera, by
disconnecting and reconnecting power.
5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.
6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on
your keyboard.
Notes:
• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.
• To use the ARP command in Windows Vista, right-click the command prompt icon and select Run as
administrator.
• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.
arp -s 192.168.0.125 00-40-8c-18-10-00
ping -l 408 -t 192.168.0.125
arp -s 192.168.0.125 00:40:8c:18:10:00 temp
ping -s 408 192.168.0.125
ENGLISH
Page 18 AXIS P5532-E/AXIS P5534-E Installation Guide
Status indicators
Unit Color Indication
AXIS P5532-E
AXIS P5534-E
Note:
For more information on the AXIS P5532-E/AXIS P5534-E status indicators, please see the User’s Manual available from the AXIS Network Video Product CD supplied with this product or from the website at www.axis.com
Unit Color Indication
AXIS T8123 Port Unlit No camera connected
AC input Steady green AC power connected
Unlit Steady connection/normal operation
Amber Steady during system initiating and reset to factory default.
Flashes during firmware upgrade.
Amber/red No network connection
Red Firmware upgrade failure
Green Steady for 10 sec. after successful restart
Flashing Power overload or other input voltage error
Green Camera connected, normal behavior
AXIS P5532-E/AXIS P5534-E Installation Guide Page 19
Tip!
Visit www.axis.com/techsup to check if there is updated firmware available for your
network camera. To see the currently installed firmware version, see Setup > About.
Resetting to the Factory Default Settings
To reset the camera to the original factory default settings, use the control button and the restart
button on the side of the camera, see
Using the control and restart buttons will reset all the parameters, including the IP address, to the
factory default settings:
1. Remove the sunshield, see illustration on page 6.
2. Remove the top cover, see
3. Press and hold the control button and the restart button at the same time.
4. Release the restart button but continue to hold down the control button.
5. Continue to hold down the control button until the status indicator flashes amber at regular
intervals (this may take up to 15 seconds).
6. Release the control button.
7. When the status indicator changes to green (which may take up to 1 minute), the process is
complete and the camera has been reset. The unit now has the default IP address 192.168.0.90
8. Put the top cover back in its original position.
9. Put the sunshield back in its original position.
10. Re-assign the IP address, using one of the methods described in
11.
It is also possible to reset parameters to the original factory default settings via the web interface.
For more information, please see the online help or the User’s Manual available from the AXIS
Network Video Product CD supplied with this product.
Hardware overview,
on page 6, as described below:
Remove the protective packaging,
on page 7.
Assign an IP address,
on page
ENGLISH
Accessing the camera from the Internet
Once installed, your network camera is accessible on your local network (LAN). To access the
camera from the Internet, network routers must be configured to allow incoming traffic, which is
usually done on a specific port.
• HTTP port (default port 80) for viewing and configuration
• RTSP port (default port 554) for viewing H.264 video streams
Please refer to the documentation for your router for further instructions. For more information on
this and other topics, visit the Axis Support Web at www.axis.com/techsup
Further information
The User’s Manual is available from the Axis Web site at www.axis.com or from the Axis Network
Video Product CD supplied with this product.
Mesures de sécurité
Lisez attentivement le présent guide d’installation avant d’installer le produit. Conservez le guide d’installation
si vous souhaitez le consulter ultérieurement.
ATTENTION !
• Pour éviter d’endommager le produit Axis, utilisez l’emballage d’origine ou un équivalent pour le
transporter.
• Évitez d’exposer le produit Axis à des vibrations, des chocs ou une trop forte pression et ne l’installez pas
sur des supports instables, ou des surfaces ou des murs instables ou vibrants. Cela risque de l’endommager.
• Utilisez uniquement des outils manuels pour l’installation du produit Axis, l’utilisation d’outils électriques
ou l’usage excessif de la force risque de l’endommager.
• N’utilisez ni produits chimiques, ni substances caustiques, ni nettoyeurs aérosol. Utilisez un linge humide
pour le nettoyage.
• Utilisez uniquement des accessoires et des pièces de rechange fournis ou recommandés par Axis.
• Ne tentez pas de réparer le produit vous-même, contactez Axis ou votre revendeur Axis pour tout problème
lié au service.
IMPORTANT !
• Ce produit Axis doit être utilisé conformément aux lois et réglementations locales en vigueur.
Remplacement des piles
Ce produit Axis nécessite une pile au lithium CR2032 de 3,0 V pour l’alimentation de son horloge en temps réel
interne. Dans des conditions normales d’utilisation, cette pile devrait durer au moins 5 ans. Si la pile est faible,
cela a un impact sur le fonctionnement de l’horloge en temps réel qui se réinitialise alors à chaque mise sous
tension. Un message enregistré apparaît lorsque la pile doit être remplacée. Ne remplacez la pile que lorsque
cela est nécessaire !
Si la pile doit être remplacée, veuillez contacter www.axis.com/techsup pour obtenir de l’aide.
• Afin d’éviter tout risque d’explosion, remplacez correctement la pile.
• Remplacez la pile par une pile identique ou équivalente uniquement, en respectant les recommandations du
fabricant.
• Jetez les piles usagées conformément aux consignes du fabricant.
Nettoyage de la bulle du dôme
• Veillez à ne pas rayer ou endommager la bulle du dôme. Ne nettoyez pas la bulle du dôme si elle semble
propre à l'œil nu et ne frottez jamais la surface. Un nettoyage excessif peut endommager la surface.
• Pour le nettoyage général de la bulle du dôme, il est recommandé d'utiliser un savon ou un détergent
neutre sans solvant, non abrasif, avec de l'eau et un chiffon doux. Rincez abondamment avec de l’eau douce
et tiède. Séchez à l’aide d’un chiffon doux pour éviter les salissures d’eau.
• N’utilisez jamais de détergents forts, d’essence, de benzène ou d’acétone, etc. et évitez de vous exposer
directement aux rayons du soleil ou à des températures élevées lors du nettoyage.
AXIS P5532-E/AXIS P5534-E Guide d'installation Page 21
Important !
Ce produit doit être utilisé
conformément aux lois et
réglementations locales en vigueur.
AXIS P5532-E/AXIS P5534-E
Guide d’installation
Ce guide d’installation explique comment installer une AXIS P5532-E/AXIS P5534-E Caméra réseau
à dôme PTZ sur votre réseau. Pour toute autre question concernant l’utilisation du produit,
reportez-vous au manuel d’utilisation du produit, que vous trouverez sur le CD joint ou sur le site
www.axis.com
Procédure d’installation
1. Vérifiez que l’emballage contient bien tous les
éléments répertoriés dans la liste ci-dessous.
2. Vue d’ensemble du matériel. Reportez-vous à la
page 22.
3. Installation du matériel. Reportez-vous à la page 23.
4. Attribution d’une adresse IP. Reportez-vous à la page 27.
5. Configuration du mot de passe. Reportez-vous à la page 30.
Contenu de l’emballage
Élément Modèles/variantes/remarques
Caméra réseau AXIS P5532-E/AXIS P5534-E 50 Hz/60 Hz
Bulles des dômes Bulle transparente non fumée (prémontée)
Bulle transparente fumée
Injecteur de puissance High PoE AXIS T8123 avec câble d’alimentation fourni (différent selon les pays)
Connecteur RJ45 Connecteur réseau norme IP66
Pare-soleil Bulle de protection en plastique, vis fournies
CD CD de la caméra vidéo réseau Axis comprenant la documentation,
les outils d’installation et des logiciels complémentaires
Documentation imprimée Guide d’installation de l’AXIS P5532-E (le présent document)
Document de garantie d’Axis
Étiquettes de numéro de série supplémentaires (2x)
FRAN
Ç
AIS
Accessoires en option Accessoires de montage AXIS T91A
Consultez le site à l’adresse www.axis.com pour plus d’informations sur les
accessoires disponibles
Page 22 AXIS P5532-E/AXIS P5534-E Guide d'installation
Supports de rack (3)
Connecteur réseau (PoE)
Crochet pour fil de sécurité
Pare-soleil
Vis (3)
Bulle du dôme
Référence (P/N) et numéro de série (S/N).
Le numéro de série peut être demandé
pendant l’installation.
Logement de carte SDHC
Voyant d’état
Bouton Redémarrer
Bouton de commande
Anneau du dôme
Bulle du dômeVis (6)
Couvercle supérieur
Anneau d’étanchéité
Vis du couvercle
supérieur (4)
Description du matériel
AXIS P5532-E/AXIS P5534-E Guide d'installation Page 23
Emballage de protection
Installation du matériel
Préparation de l’installation
Lisez toutes les instructions avant de préparer l’installation de la caméra réseau. En effet, de
nombreuses étapes de cette préparation requièrent le retrait du couvercle supérieur et il serait plus
judicieux de les effectuer ensemble. Le pare-soleil doit être retiré pour installer/enlever une carte
SD. Reportez-vous à
• Suivez les instructions décrites dans la section ci-après
protection
• La caméra réseau est fournie avec deux bulles transparentes (non fumée et fumée). Si
nécessaire, suivez les instructions décrites dans la section
fumée/non fumée (facultatif)
• Une carte SD standard ou haute capacité (non fournie) est requise pour stocker des images
en local sur la caméra réseau. Suivez les instructions décrites dans la section
d’une carte SD (facultatif)
Installation d’une carte SD (facultatif),
pour enlever l’emballage de protection, avant d’installer la caméra.
ci-après pour replacer la bulle du dôme.
ci-après pour retirer la bulle du dôme et installer la carte SD.
Enlèvement de l’emballage de protection
1. Desserrez les quatre vis du couvercle supérieur et retirez-le, voir l’illustration à la page 22.
2. Enlèvement de l’emballage de protection.
à la page 24.
Enlèvement de l’emballage de
Replacement de la bulle du dôme
Installation
FRAN
Ç
AIS
3. Si vous replacez la bulle de dôme fumée/non fumée, ou installez la carte SD, suivez les
instructions décrites dans les sections
(facultatif)
4. Remettez en place le couvercle supérieur, puis serrez les vis.
et
Installation d’une carte SD (facultatif),
Replacement de la bulle du dôme fumée/non fumée
à la page 24.
Page 24 AXIS P5532-E/AXIS P5534-E Guide d'installation
Replacement de la bulle du dôme fumée/non fumée (facultatif)
IMPORTANT !
!
Cette caméra dispose d’une membrane de déshumidification qui permet de maintenir de faibles
niveaux d’humidité dans le dôme. Pour éviter toute condensation, ne démontez pas la caméra s’il
pleut ou s’il fait humide.
1. Desserrez les quatre vis du couvercle supérieur et retirez-le, voir l’illustration à la page 22.
2. Desserrez les six vis de l’anneau du dôme, puis retirez ce dernier du couvercle supérieur.
3. Fixez l’anneau et la bulle du dôme sur le couvercle supérieur, puis serrez les six vis.
4. En cas d’installation de la carte SD, reportez-vous aux instructions décrites dans la section
Installation d’une carte SD (facultatif)
5. Remettez en place le couvercle supérieur, puis serrez les vis.
Remarque :
Veillez à ne pas rayer ou endommager la bulle du dôme. Laissez, si possible, la protection en
plastique sur la bulle du dôme jusqu’à la fin de l’installation.
ci-après.
Installation d’une carte SD (facultatif)
1. Retirez le pare-soleil, voir l’illustration à la page 22.
1. Desserrez les quatre vis du couvercle supérieur et retirez-le, voir l’illustration à la page 22.
2. Insérez une carte SD (non fournie) dans le logement de carte SDHC (Secure Digital High
Capacity).
3. Remettez en place le couvercle supérieur, puis serrez les vis.
4. Remettez en place le pare-soleil, puis serrez les vis.
Remarque :
La carte SD est automatiquement installée une fois insérée dans le logement de carte
SDHC. Il est cependant nécessaire de désinstaller la carte SD à partir des pages Web de la
caméra avant de la retirer. Choisissez Setup > System Options > Storage > SD Card
(Configuration > Options système > Stockage > Carte SD), puis cliquez sur Unmount
(Désinstaller). Pour plus d’informations, consultez le manuel de l’utilisateur, disponible sur
le CD du produit de vidéo sur IP AXIS, fourni avec le produit ou en téléchargement sur le
site Web www.axis.com
AXIS P5532-E/AXIS P5534-E Guide d'installation Page 25
Plaquette de fixation murale (exemple de montage,
Fil de
sécurité
Logements pour
Torx T30
Vis
supports de rack
plaquette non incluse)
Installation de la caméra réseau
IMPORTANT !
!
Le design norme IP66 de la caméra nécessite l’utilisation des connecteurs RJ45 ou RJ45
compatible norme IP66 fournis.
1. Installez le support choisi (non inclus)
conformément aux instructions fournies avec le
support. S’il s’avère nécessaire de percer,
vérifiez que les forets, vis et chevilles à utiliser
sont appropriés pour le matériau. Consultez le
site www.axis.com pour plus -d’informations sur
les accessoires de montage disponibles.
2. Acheminez le câble réseau et fixez le
connecteur RJ45 fourni. Reportez-vous aux
instructions fournies avec le connecteur pour
plus d’informations sur le câblage et le
montage.
3. Accrochez la caméra au fil de sécurité du support.
4. Connectez le câble réseau et le connecteur RJ45 au connecteur réseau de la caméra.
5. Installez l’injecteur AXIS T8123, reportez-vous à la section
1 port AXIS T8123,
6. Vérifiez que les voyants lumineux sur l’injecteur indiquent les conditions correctes. Pour plus
d’informations, reportez-vous au tableau à la page 27.
7. Glissez les supports de rack de la caméra dans les logements du support, puis tournez la caméra.
8. Fixez la caméra réseau au support de fixation à l’aide des trois vis (Torx T30).
à la page 26.
Installez l’injecteur High PoE AXIS à
FRAN
Ç
AIS
Page 26 AXIS P5532-E/AXIS P5534-E Guide d'installation
Ethernet
Données et
Données d’entrée
Indicateur
du port
Indicateur
d’entrée CA
alimentation de sortie
Caméra réseau
de connexion
de connexion
AXIS T8123
Installez l’injecteur High PoE AXIS à 1 port AXIS T8123
L’injecteur de puissance Axis T8123 High PoE permet aux produits vidéo Axis consommant une
quantité importante d’énergie de recevoir des données et de l’alimentation via le même câble
Ethernet. Procédez comme suit pour connecter l’ AXIS T8123.
Remarque :
Axis peut garantir l’intégralité des fonctions pour le modèle AXIS T8123 uniquement, tout
autre périphérique High PoE n’est pas pris en charge.
1. Branchez l’AXIS T8123 (Données d’entrée) au commutateur réseau via un câble réseau standard.
2. Branchez l’AXIS T8123 (Données et alimentation de sortie) à la caméra réseau, via un câble
réseau déjà branché à la caméra.
3. Branchez l’AXIS T8123 sur une prise CA (100-240 V CA), à l’aide du câble d’alimentation fourni.
Pour plus d’informations sur les voyants lumineux de l’injecteur, reportez-vous à la section
Attribution d’une adresse IP,
à la page 27.
AXIS P5532-E/AXIS P5534-E Guide d'installation Page 27
Attribution d’une adresse IP
Aujourd’hui, la plupart des réseaux sont équipés d’un serveur DHCP qui attribue automatiquement
des adresses IP aux périphériques connectés. Si votre réseau ne possède pas de serveur DHCP, la
caméra réseau utilise l’adresse IP 192.168.0.90 comme adresse IP par défaut.
Si vous souhaitez paramétrer une adresse IP statique sous Windows, nous recommandons
l’utilisation de l’application AXIS IP Utility ou de l’application AXIS Camera Management. Selon le
nombre de caméras à installer, choisissez la méthode qui vous convient le mieux.
Ces deux applications gratuites sont disponibles sur le CD du produit de vidéo sur IP Axis fourni
avec ce produit. Vous pouvez également les télécharger à partir du site www.axis.com
Méthode Recommandée pour Système d’exploitation
AXIS IP Utility
Voir page 28
AXIS Camera Management
Voir page 29
Remarques :
• En cas d’échec de l’attribution d’adresse IP, vérifiez qu’aucun pare-feu ne bloque l’opération.
• Pour connaître les autres méthodes d’attribution ou de détection de l’adresse IP, par exemple sous
d’autres systèmes d’exploitation, reportez-vous à la page 32.
Une seule caméra
Petites installations
Plusieurs caméras
Grandes installations
Installation sur un autre sousréseau
Windows
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista
Windows 7
FRAN
Ç
AIS
Page 28 AXIS P5532-E/AXIS P5534-E Guide d'installation
AXIS IP Utility : une seule caméra et une petite installation
AXIS IP Utility détecte et affiche automatiquement les périphériques Axis présents sur votre réseau.
Cette application peut également être utilisée pour attribuer manuellement une adresse IP statique.
Notez que l’ordinateur exécutant l’application AXIS IP Utility doit se trouver sur le même segment
de réseau (sous-réseau physique) que la caméra réseau.
Détection automatique
1. Vérifiez que la caméra est connectée au réseau et qu’elle est sous tension.
2. Lancez AXIS IP Utility.
3. Lorsque l’icône de la caméra apparaît dans la fenêtre, cliquez deux fois dessus pour ouvrir la
page d’accueil correspondante.
4. Reportez-vous à la page 30 pour savoir comment configurer le mot de passe.
Attribution manuelle de l’adresse IP (facultatif)
1. Trouvez une adresse IP non utilisée sur le même segment de réseau que celui de votre
ordinateur.
2. Sélectionnez la caméra réseau dans la liste.
3. Cliquez sur le bouton Assign new IP address to the selected device (Attribuer une nouvelle
adresse IP au périphérique sélectionné)
4. Cliquez sur le bouton Assign (Attribuer) et suivez les instructions qui s’affichent à l’écran. La
caméra doit être redémarrée dans les 2 minutes pour que la nouvelle adresse IP soit prise en
compte.
5. Cliquez sur le bouton Home Page (Page d’accueil) pour accéder aux pages Web de la caméra.
6. Reportez-vous à la page 30 pour savoir comment configurer le mot de passe.
, puis saisissez l’adresse IP.
Loading...