MANUAL RE-PAINT
AXIS P551X/-E
Network Dome Cameras
AXIS 66583 REV: 2
COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07
Author: Sven Svensson PAGE: 2(23)
1 Table of Contents
1 Table of Contents ________________________________________________________ 2
2 Introduction ____________________________________________________________ 3
3 Influence on Warranty and Product performance ______________________________ 3
3.1 Product Warranty _________________________________________________________ 3
3.2 Product Performance ______________________________________________________ 3
4 Tools Required __________________________________________________________ 3
5 Repaint instruction for P551X-E series ______________________________________ 4
5.1 Repainting of the Chassis ___________________________________________________ 4
5.1.1 Removal of weather shield _______________________________________________________ 4
5.1.2 Removal of the Dome Module Ass _________________________________________________ 5
5.1.3 Removal of the Push-pull Connector Housing ________________________________________ 6
5.1.4 Removal of the Chassis Hook _____________________________________________________ 7
5.1.5 Removal of the Screws Bayonett __________________________________________________ 7
5.1.6 Create a masking box for the Chassis and position the unit ______________________________ 8
5.1.7 Masking of the Chassis __________________________________________________________ 9
5.2 Repainting of the Dome Module Ass _________________________________________ 10
5.2.1 Removal of the Dome Module Bracket & the Dome with sealing ________________________ 10
5.2.2 Removal of the dome sealing ____________________________________________________ 12
5.2.3 Mask Gore filters. _____________________________________________________________ 12
6 Repaint instruction for P551X series _______________________________________ 13
6.1 Repainting of the Chassis __________________________________________________ 13
6.1.1 Removal of the Chassis Hook and Lid _____________________________________________ 14
6.1.2 Removal of the Screws Bayonett _________________________________________________ 14
6.1.3 Create a masking box for the Chassis and position the unit _____________________________ 16
6.1.4 Masking of the Chassis _________________________________________________________ 16
6.2 Repainting of the Dome Module Ass _________________________________________ 18
6.2.1 Removal of the Dome Module Bracket & the Dome with sealing ________________________ 18
6.2.2 Removal of the dome sealing ____________________________________________________ 19
7 APPENDIX: Assembly drawings and overview of products _____________________ 20
7.1 Assembly drawings of P551X-E series _______________________________________ 20
7.1.1 Main Assembly _______________________________________________________________ 20
7.1.2 Weather Shield Assembly _______________________________________________________ 21
7.1.3 Dome Module Assembly ________________________________________________________ 21
7.2 Assembly drawings of P551X series _________________________________________ 22
7.2.1 Main Assembly _______________________________________________________________ 22
7.2.2 Dome Module Assembly ________________________________________________________ 22
8 Revision History ________________________________________________________ 23
- 2 -
AXIS 66583 REV: 2
COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07
Author: Sven Svensson PAGE: 3(23)
2 Introduction
This document describes the way to operate when Re-painting a P551X / -E Network Dome
Camera. Any attempt to carry out a Re-painting operation on the camera, should only be
made after reading this document thoroughly.
To prevent damage to sensitive components, proper ESD protection must be carried out
while handling of the parts is only allowed in dust free environment.
3 Influence on Warranty and Product performance
3.1 Product Warranty
Any aftermarket modifications, which are not approved by Axis Communications AB, made
on Axis Network Dome cameras will void the Product warranty. Therefore, please note that
any deviation from the re-paint instructions described in this document will void the Product
warranty.
3.2 Product Performance
Axis Communications AB will only guarantee the product specifications and performance of
the camera in its original form.
4 Tools Required
Torx Screwdriver, (T8, T10, T20)
Screwdriver Flat > 6 mm width
Carton box min 190x190x140 mm
Knife for cutting in carton
- 3 -
AXIS 66583 REV: 2
Screws (3x)
T20
COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07
Author: Sven Svensson PAGE: 4(23)
5 Repaint instruction for P551X-E series
To repaint the P551X-E series Dome Network Camera, the camera will have to be divided into thee
parts: Weather Shield, Chassis and Dome Module. Each part is then stripped from components or
masked to enable the repainting. Before the painting, crucial parts of the camera are masked to
ensure the fit and function when the camera is reassembled again.
To prevent damage to sensitive components, proper ESD protection must be carried out while
handling of the parts is only allowed in dust free environment.
Please follow the workflow as described below. Any deviations from the proposed instruction will void
the Product warranty.
5.1 Repainting of the Chassis
Please note that the original surface finish of the chassis is Powder coating.
5.1.1 Removal of weather shield
Tool: Screwdriver Torx20
Torque (when refitting): 2 Nm
Put the weather shield to the side for painting.
- 4 -
AXIS 66583 REV: 2
Antiloss Screws
(4x)
COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07
Author: Sven Svensson PAGE: 5(23)
5.1.2 Removal of the Dome Module Ass
Step 1
Remove the four Antiloss screws that hold the Dome module ass. Remove the Dome module ass.
Tool: Screwdriver Torx20
Torque (when refitting): 2 Nm
When refitting, Please note:
1) The Max tightening torque must not exceed 2 Nm
- 5 -
AXIS 66583 REV: 2
Screws (3x)
Push Pull Housing
COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07
Author: Sven Svensson PAGE: 6(23)
5.1.3 Removal of the Push-pull Connector Housing
Step 1
Remove the two screws that hold the Push-pull connector housing and remove the housing.
Tool: Screwdriver Torx8
Torque (when refitting): 0,3Nm
- 6 -
AXIS 66583 REV: 2
Screws (3x)
Chassis hook
Screw Bayonett (3x)
COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07
Author: Sven Svensson PAGE: 7(23)
5.1.4 Removal of the Chassis Hook
Step 1
Remove the three screws that hold the Chassis hook.
Tool: Screwdriver Torx20
Torque (when refitting): 2,4Nm
When refitting, Please note:
Please note the maximum torque of 2,4 Nm.
5.1.5 Removal of the Screws Bayonett
Remove the three Bayonett screws.
Tool: Screwdriver, Minus Bit
Torque (when refitting): 1,8Nm
When refitting, Please note:
Please note the maximum torque of 1,8Nm.
- 7 -
Loading...