AW-Lake FEM-03 Data sheet

8809 Industrial Drive, Franksville, WI 53126 Phone: [phone] Fax: [phone]

Email: [e-mail] www.awflowmeters.com

Technical Specifications:

· Single or dual channel · Rate, flow, limit or ratio monitor

· RS-232 communication · Two programmable Form C Relay outputs

· Easy to read graphic display · Assignable 4-20 mA output

· Monitor/Display · Multiple display modes

What is a FEM-03 Flow Monitor?

The FEM-03 is available as a simple, compact easy to use flow monitor. A large, backlighted
LCD graphic display provides easy to read indication of flow rate, totals or ratios. Two Form C
relay outputs can be programmed to perform limit, warning or alarm functions. Remote pro­gramming or monitoring is available via the RS-232 serial communications port. The FEM­03A model has a 4-20mA output to track data remotely. The FEM-03A2 model is equipped
with 2 channels to monitor dual flows and display them separately or as a sum (as in total
material use) or as a difference (as in fuel consumption) or as a ratio of A/B. This unit can
also be configured to monitor and detect bi-directional flow when “A” and “B” channel (90°
phase shifted) signals are available from a single flow meter.

FEM-03

Flow Monitor

Rev. 01/06

8809 Industrial Drive, Franksville, WI 53126 Phone: [phone] Fax: [phone]

Email: [e-mail] www.awflowmeters.com

Power Supply:

16 VAC/500mA with supplied
110 VAC Transformer

OR

24 VDC/200mA (customer supplied)

Flow Sensor Power Supplies:

(2) @ 15 VDC/20 mA each

Frequency Inputs:

0-4 KHz, Sine, Square or Saw-tooth
2 Volts minimum amplitude,
10 Kohm impedance

4-20 mA Analog Output:

Self powered loop output into a
maximum 400 ohm load impedance.

Monitor T

echnical Data

FEM-03 Flow Monitor

Rev. 01/06

Products may be subject to change without notice – Contact factory for current information

Relay Contact Ratings:
Maximum Switch Voltage: 220V DC, 250 VAC
Maximum Switch Current: 2A

Maximum Switched Power
Resistive Load: DC 60W / AC 125 VA
Inductive Load: DC 30W / AC 60 VA

Rated Load
Resistive Load: DC 30V, 2A / AC 110V 0.5A
Inductive Load: DC 30V, 1A / AC 110V 0.3A

Ordering Information:

Single Channel Rate/Totalizer FEM-03

A ___
Two Form C Limit Relay Outputs
RS-232 Communications

With a 4-20 Milliamp Output

Dual Channel Rate/Totalizer
With Bi-directional Flow Indication
Dual Channel Ratio Monitor

X

2

MODERESET

DN

PRO G

UP SEL ENT

3.8”/97mm

2.8”/72mm

5.2”/132mm

5.5”/139mm

1 2 3 4 5 6 7 8 9 10

Terminal

Upper

Connector

Terminal

Lower

Connector

#1 +15 VDC Out #1 +15 VDC Out
#2 DC Common #2 DC Common
#3 Freq. A Input #3 Freq B Input
#4 Not Used #4 RS232 TX Output
#5 Not Used #5 RS232 RX Output
#6 +mA Output #6 Reset Total
#7 -mA Output #7 DC Common
#8 Limit 2 Common #8 Limit 1 Common
#9 Limit 2 N.C. #9 Limit 1 N.C.

#10 Limit 2 N.O. #10 Limit 1 N.O.