AW-Lake DSV-100 Data sheet

8809 Industrial Drive, Franksville, WI 53126 Phone: [phone] Fax: [phone]

Email: [e-mail] www.awflowmeters.com

Technical Specifications:

· Digital processing · Integral LED display modes

· Programmable set-up · Lightweight compact design

· Pressure rating up to 100 PSI · Multiple input modes

· Din Rail or Panel Mount · Front touch key control

What is a DSV-100 I/P Converter?

The DSV-100 I/P Converter is a compact high performance digital servo pressure control valve.
Accepting either current, voltage or touch key input, the I/P Converter precisely regulates air pressure
for directing process control valves and air or fluid regulators. The microprocessor-based converter
delivers high accuracy pressure regulation with extremely low dynamic response times for improved
process control and high product quality. A highly visible integral LED display eliminates the need to
any additional display components, providing a display of actual pressure, set point pressure or the
actual pressure deviation from set point. Additional diagnostic test modes measure the system
response time or checks for line leaks providing actual real-time data invaluable in commissioning,
monitoring or troubleshooting an installation. User set-up of output pressure range and input voltage
or current-span is accomplished quickly and easily via the two touch keys and display. The lightweight
design and compact DIN rail mount package maximizes panel component density while the push-in
type 1/4” pneumatic hose connectors and 5 pin style electrical connection with molded cable
assemblies minimize installation time and cost.

DSV-100

I/P Converter

Rev. 02/07

8809 Industrial Drive, Franksville, WI 53126 Phone: [phone] Fax: [phone]

Email: [e-mail] www.awflowmeters.com

Converter Technical Data

DSV-100 Series I/P Converter

Rev. 02/07

Products may be subject to change without notice – Contact factory for current information

Power Requirements:

Supply Voltage 10 - 24 VDC
Supply Current 85 mA. @ 15 VDC

Signal Output:

Pressure Signal 0-5 VDC
(Actual pressure, 0 to 100% of programmed output range)

Signal Inputs:

Voltage Input 0-5, 0-10 or 1-5 VDC
Voltage Input Impedance 10 Kohm
Current Input 0-20 mA, 4-20 mA
Current Input Impedance 250 ohm

Specifications:

Pressure Range 0-100 psig
Output Pressure 0-100% (programmable)
Flow Rate, 100 psig @ Inlet 0.6 SCFM max
Recommended Filtration 20 Micron
Min. Closed End Volume 2.13 cu. in. (35 ml)
Linearity (typical) ±0.1% F.S.
Hysteresis (typical) ±0.1% F.S.
Repeatability (typical) ±0.2% F.S.
Accuracy (typical) ±0.3% F.S.

Wetted Parts:

Elastomers RTV, Glass
Manifold Aluminum
Valves Nickel Plated Brass
Press. Transducer RTV, Aluminum, Plastic

Physical:

Operating Temp. Range 32-158°F (0-70°C)
Weight 1.0 lb (.45 Kg.)
Housing Polycarbonate
Protection Rating NEMA 12 (IP55)

Dynamic Response:

10 - 90% F.S. Rated Output 180 ms.
Response Test Volume 0.76 cu. in. (12.5 ml)

3

4

2

5

1

Electrical Connection for

Voltage Input

Connector Pin

10-24 VDC Supply 1-Supply

Supply/Signal Common 2-Ground
Control Voltage Signal 3- +M/mA In
Not used 4-Not used
Analog Pressure Output 5-Analog Output 0-5V

Electrical Connection for

Voltage Input

Connector Pin

10-24 VDC Supply 1-Supply
Supply Common 2-Ground
+ mA Control Signal 3- +V/mA In

-mA Control Signal 4- -mA
Analog Pressure Output 5-Analog Output 0-5V