AVSL DM-X24 User Manual

Download

DM-X24

24 Channel DMX Dimmer Console

USER MANUAL

154.095 UK

Version 1.0

TABLE OF CONTENTS

DMX 512 CONTROLLER SERIES

Before You Begin

What is included Unpacking Instructions Safety Instructions

Introduction

Features Product Overview(front) Product Overview(rear panel) Common Terms

Operating Instructions

Setup Setting up the System Physical fader Assignment(iptional setup)

Programming

Entering program mode (record enable) Create a scene Edit Enable Erase a Program Erase all Scenes Record Clear Delete a step or steps Insert a step or steps Modify a step or steps

Playback

Playing a Scene Playing a Scene to audio Triggering Playing a Scene with the Speed slider Plating a Scene with the Standard beat Change the Speed mode between 5 & 10 minutes Auxiliary controls Midi Operation Setting MIDI IN Setting MIDI OUT Receiving MIDI File Dump Sending MIDI File Dump

Appendix

DMX Primer Fixture Linking General Troubleshotling DMX Dip switch Quick Reference Chart Technical Specifications

Quick operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2 2 2

3 3

4-5

6 6

7 7 7

9 9

10 10 11

11 11 12

12 12

13 13

14 14 15 15 17

USER MANUAL

1/19

DMX 512 CONTROLLER SERIES

1.BERORE YOU BEGIN

What is included

Dimmer console 1) Dimmer console

2) DC 9-12V 1000mA output, 100V~240V, 50/60Hz input auto-ranging Power Supply

3) Manual

4) LED gooseneck lamp

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. notify the shipper immediately and retain packing material for inspection if and parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. ln the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

Safety instructions

Please read these instructions carefully, which includes important information about the installation, usage and maintenance of your fixture.

Please keep this User Guide for future consultation. lf you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture. This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating. In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. Dont connect the device to a dimmer pack. Make sure power cord is never crimped or damaged. Never disconnect power cord by pulling or tugging on the cord. Do not operate this device in more than 104F(40 )ambient temperatre conditions.

Caution!

There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service. Please contact us!

USER MANUAL

2/19

DMX 512 CONTROLLER SERIES

2.INTRODUCTION

The dimmer console is a universal intelligent lighting controller. lt allows the control of 48 channels with 48 scene/chase playback faders Each scene/chase can contain up to 1000 individual steps, or looks. On the surface, when in the CHASE SCENE mode, there are 12 physical faders fo the playback of the saved programs. There are 4 pages of scenes playback on page A. . programs can be triggered by music, midi,automatically or manually . Channel assignments can be reprogrammed for ease of controlling different fixtures. On the surface you will find various programming tools tools such as 24channel faders. A/Bmaster fa ders for cross mixing. A nd Fade and Speed time faders for on the fiy adjustments. And it also has an LED display for easy navigation of controls and menu functions.

Features

* 24-channel DMX-512 dimming console * 4 pages with 12 scenes each yields 48 total playback faders (simultaneous playback) * 96,000 programmable steps * 2 programmable aux buttons * Adjustable chase and fade times * Re-assignable channels

Additional Features * 3-pin and 5-pin DMX connections * Built-in cross fader, dark and kill buttons * MIDI in, out and thru (with file dump) * Direct audio input * Sequential linking or simultaneous playback of chases * Override chases on the fly * Beat-activation, tap sync, auto run, midi in/out * 7-space (7 U) rack mount

USER MANUAL

3/19

Product Overview(front)

3 4

DMX 512 CONTROLLER SERIES

6 7 8 9 1110 12

15 28

29 30

16 18 21 24 272219

ITEM Button or Fader Function

1 Channel Faders Indicates channels 1-12

Channel Flash button

2 3 Channel Faders Indicates channels 13-24

4 5

8 LCD Display 9

Scene Playback indicators

Channel Flash button

Down/Beat Rev

Up/Chase Reverse

Delete/Rev One

Brings the relevant fader to 100% or DMX value of 255

Indicates that the scene is playing back Brings the relevant fader to 100% or DMX value of

255 Down functions to modify a scene in Edit mode, Beat

Rev is used to reverse the chasing direction of a program with regular beat.

Up function to modify a scene in Edit mode, chase Reverse is used to reverse the chasing direction of a program under Speed Slider control.

Shows the current activity or programming state Delete a step in a scene or reverse the chasing

direction of any program

Aux 1

Insert % or 255

Patchable; used to control a channel in 1 of 2 modes of operation

Insert is to add 1 step or steps into a scene; %or255 is used to change the display value cycle between % and 0-255

USER MANUAL

4/19

DMX 512 CONTROLLER SERIES

17 18

Aux 2

Edit/All Rev

Record/Shift

Audio Audio activate audio sync of a program

Blind

Dark Home

Park

Patchable; used to control a channel in 1 of 2 modes of operation

Edit is used to activate Edit mode; All Rev is to reverse the chasing direction of all programes

Record is used to activate Record mode or program a step; Shift functions the alternate function of other buttons only

Take the channel out of a program temporarily in Chase Scene mode

Used to temporarily blackout overall output Used to deactivate the Blind on a given channel

Used to select Single/Mix Chase, bring Channel 1324 to full of current setting, or momentarily program a scene into Master B slider depending on the current mode

21 22

23 24 25

27 28 29 30

Mode Select/Rec Speed

Tap Sync Hold

Page

Full On Step

Add Kill/Rec exit

Blackout Audio Level Fader Speed Fader

Fade Fader

Used to activate the operating mode; Rec Speed sets the speed of any programs chasing in Mix mode

Repeatedly tapping this button will establish the chase speed

Used th momentarily maintain current scene Tap to select pages of scenes from 1-4(Page A)

Momentarily bring all channels(1-24)to full intensity Used to go to the next step when the Speed slider is

set in Show Mode or in Edit mode In Add mode, multiple scenes or Flash buttons will be

on at the same time; ln kill mode, pressing any Flash button will kill any other scenes or programes; Rec Exit is used to exit from Program or Edit mode

Used to kill all output, with exception of Full On Adjusts the audio sensitivity when in Audio trigger

mode of scenes Used to adjust the speed of scenes/chases running

Adjusts the fade-in,fade-out,and cross-fade times

Master A-B

Adjusts overall intensity

USER MANUAL

5/19

Product Overview(rear panel)

DMX 512 CONTROLLER SERIES

POWERPOWER

DC INPUTDC INPUT

9V 9V 1000mA1000mA

MIDIMIDI

THRU OUT IN

DMX 512 OUTPUTDMX 512 OUTPUT

2=DATA

1=GROUND

DMX OUTDMX OUT

3=DATA+

DMX INDMX IN

LAMPLAMP AUDIOAUDIO REMOTEREMOTE

1 24 5 63 7 89

ITEM Button or Fader Function

1 3-pin DMX output connector DMX control signal

USB Lamp Socket

ON/OFF power switch Switch the controller on and off

MIDI Thru

MIDI Out

MIDI ln

MIDI port for connecting to a sequencer or MIDI device

SERIAL NO :SERIAL NO :

Audio Input

Remote Input

DC Input

This jack accepts a line level audio input signal ranging from 100 mV to 1Vpp

Blackout and Full On may be controlled by a remote control using a standard 1/4 jack

DC 9V, 1000mA

Common Terms

The following are common terms used in intelligent light programming.

Blackout is a state where all lighting fixtures light output are set to 0 or off, usually on a temporary basis. DMX-512 is an industry standard digital communication protocol used in entertainment lighting equipment. For more information read Sections DMX Primer and DMX Control Mode in the Appendix. Fixture refers to your lighting instrument or other device such as a fogger or dimmer which you can control. Programs are a number of scenes arranged one after another. It can be programmed as either a single scene or multiple scenes in sequence.

USER MANUAL

6/19

DMX 512 CONTROLLER SERIES

Scenes are static lighting states. Sliders are also known as faders. Chases can also be called programs. A chase consists of scenes arranged one after another. Scanner refers to alighting instrument with a pan and tilt mirror , however DMX controllers can use this term to control any DMX-512 compatible device as a generic fixture. MIDI is a standard for representing musical information in a digital format. A MIDI input would provide external triggering of scen es using midi devices such as a midi keyboard. Stand Alone refers to a fixtures ability to function independently of an external controller and usually in sync to music, due to a built in microphone. Fade slider is used to adjust the fade time between scenes within a chase. Speed slider affects the amount of time a scene will hold its state it is also considered a wait time. Shutter is a mechanical device in the lighting fixture that allows you to block the lights path. It is often used to lessen the intensity of the light output and to strobe. Patching refers to the process of assigning fades to a DMX channel within a fixture Playbacks can be either scenes or chases that are directly called to execution by the user. A playback can also be considered program memory that can be recalled during a show.

3.OPERA TING INSTRUCTIONS

Setup

SETTING UP THE SYSTEM

1) Plac e the 24 CH dimmer console on a level surface Note! The console can also be rack mounted, occupying six rack spaces(7u).

2) Plug the AC to DC power supply into the system back panel and into the mains outlet.

3) Plug in your DMX cable(s)to your intelligent lighting as described in the respective fixtures manual. For a quick overview of DMX see the DMX Primer on page 11.

4) Reset the system using the instructions on page 9 under ERASE ALL SCENES.

PHYSICAL FADER ASSIGNMENT(OPTIONAL SETUP)

Use this feature combine or unify fixture control attributes for different fixtures. For example; if you were controlling 4 moving mirrors and 4 moving yokes, the color, gobo and dimmer channels may not line up ideally on the physical faders. Use this function to re-assign the dimmer, color and gobo channels 1,2 and 3. From now on you will be able to control the same attributes on all fixtures using the same fader location. This is also most useful when needing to combine all colors together.

ACTION:

1. Press and hold RECORD button.

2.While holding the Record button. Press the Flash button #6(3) time.

3.Press the Flash button that you wish to assign the DMX channel output to.

USER MANUAL

7/19

DMX 512 CONTROLLER SERIES

4.White holding Record, press the Flash button corresponding to the DMX output that you wish to assign the Fader to.

5.Repeat steps 2-3 as often as necessary

6.Press and hold Record & Rec Exit to exit the mode.

For example: you wish to assign Fader #1 to output to DMX channel #5

1. Hold the Record button & press Fader#6 (3 times)

2. Press the Flash button #1.

3. While holding the Record button, press the Flash button #5.

NOTES:

Al physical faders can be re-assigned to output on a different DMX channel, Faders are given a channel number and are labelled on the surface of the controller as such. You can check to see what the assignment is by pressing the Fader button of the corresponding channel while in this mode. Here is no limit to the amount of channels that can be assigned to a single faders. One can assign up to all 48 channel while in this mode. CHNO corresponds to the Physical Fader, while SLDNO corresponds to the DMX output channel.

USER MANUAL

8/19

DMX 512 CONTROLLER SERIES

4.PROGRAMMING

ENTERING PROGRAM MODE (RECORD ENABLE)

1. While holding the RECORD button, tap the Flash buttons 1-5-6-8 in sequence.

2. Release the RECORD button. The Record LED light up.

CREASE A PROGRAM

A scene is a static lighting state. Scenes are stored in the temporary memory, until they are transferred to one of the playback faders. You may create a single scene or a succession of up to 999 steps per Scene.

Action

1) Record enable.

2) Select the 1-24 Single mode by tapping the Mode Select button. This will give you control of all 24 channels of the first page.

3) Compose a look by moving the FADERS.(Changes in fixture attribute such as colors and gobos, or simply dimmer values).

4) Press Record to save the look into the temporary memory.

5) Repeat steps 2 ~ 4 until you have your desired scene.

6) Adjust the Speed and Fade sliders to achieve the desired amount of time a scene will be held in a chase (speed) and the amount of time allowed for the fixtures to move from one scene to the next (fade).

7) Select a Scene master to store your scene. Tap the Page button to select a page (1-4).

8) Press and hold the Record button & tap the Flash button for the scene that you wish to store it to. All LEDs will flash indicating the scene has been programmed into memory.

9) You can continue programming or exit. To exit program mode, press and hold the Record button & tap the Rec Exit button.

Deselect Blackout if LED is lit. If you just wish to create a static look, then you must create a scene composed of only 1 step. There are 999 steps available in every scene.

EDI T ENABLE

Action

1) Record enable.

2)Use the Page button to select the page the program you wish to edit is on.

3)Tap the Mode Select button to select Chase ..Scenes.

4)Press and hold the Edit button & tap the Flash button (13-24) of the Scene you wish to edit.

5)Release the Edit button. The relevant Scene Led should light, indicating you are in Edit mode.

Notes

When the EDIT mode is entered properly, the display will read EDITING. This mode is displayed here for only the initiation of EDIT mode. Please see the following sections on the uses of this mode in detail.

ERASE A PROGRAM ACTION

1) Record enable.

2) Use the Page button to select the page the Scene you wish to erase is on.

3)Press and hold Record button & tap the Flash button(13-24) twice of Scene you wish to erase

4)Release Record button and all LEDs should on to indicate the program is erased

ERASE ALL SCENES ACTION

1) Record enable

6) Press and hold RECORD

2) While holding record button tap the flash button in the following sequence:1-3-2-3.Relese the record button.

7) All LEDS should light indicating all program have been erases.

8) Press and hold RECORD & REX EXIT to exit the mode.

Warning :This will reset the controller to its factory defaults. This will erase all program and setting. NOTES :You must be in record mode to reset the controller. The LED over the record button will light, indicating the Record mode operation.

RECORD CLEAR ACTION

1) Record enable.

2) Record a scene with 1 or more steps.

USER MANUAL

9/19

DMX 512 CONTROLLER SERIES

3) If you are not satisfied with the scene, you may press and hold the Record button & tap the Page/REC CLR button. All LEDs will flash, indicating the scenes have been cleared.

Notes

All scenes stored in the temporary memory of the controller will be erased by this process. This process will not affect the scenes already programmed into a Scene fader.

DELETE A STEP OR STEPS

Action

1)Enter the EDIT mode.

2)Tap the Step button to scroll to the step you wish to delete

3)Tap the Delete button when you reach the step. You wish to delete.

4)Repeat step 2 and 3 all of the unwanted steps have been deleted.

5)Press and hold the Record REC Exit button. The Scene button LED will turn off, indicating that the Edit mode has been exited.

INSERT STEP OR STEPS

Action

1)Record a scene or scenes you wish to insert.

2)Be sure you are in Chase Scene and enter the EDIT mode.

3)Tap the Step button to scroll to the step which you wish to insert the step before. You may read the step from display.

4)Tap th Insert button to insert the step you have created before.

5)Exit Edit mode. NOTES :Part of entering the Edit mode is .selecting scene you wish to edit. See section on Edit enable for further instruction. AII LEDS will flash to indicating a successfully Insert of the step.

MODIFY A STEP OR STEPS Action

1)Enter EDIT mode.

3)Tap the Step button to scroll to the step which you wish to insert the step before. You may read the step from display.

4)While holding the UP or DOWN button, tap the Flash button corresponding to the DMX channel of the Scene you wish to modify until you reach the desired intensity value read from the display. Then, you may tap the Flash buttons until you are satisfied with the new Scene.

5)Repeat step2,3,and 4 until all the steps have been modified.

6)Exit EDIT mode. NOTES: Part of entering the Edit mode is selecting which scene you wish to Edit. See section on enable for further instructions. ALL LEDS will flash to indicate a successful insert of the step.

USER MANUAL

10/19

5.Playback

DMX 512 CONTROLLER SERIES

This controller uses the Channel Faders and Flash buttons for multiple uses. In this occurrence, Channel faders 13-24 are used playing back of scenes already recorded. This is only when the controller is the Chase scene mode. In this instance, Master Fader A

will control the manual fader controls, whish Master Fader B will control the Scenes being

played back.

Channel

PLAYING A SCENE

A Scene can contain 1000steps.Thrm steps and scenes interchangeably.

Action

1) Tap the ode select button to select Chase SCENE MODE.

2) Tap the page to select the correct page the program you wish to run is located.

3) Push master Slider B to its maximum position(fully down)

4) Move the desired Channel slider( 13-24) to its maximum and Scene will fade in depending upon current fade time.

5) Move the channel Slider to adjust the output of the current program. Notes: The current mode is indicated by the 3 LEDS. Red is the Chase scene . Yellow is 2- scene preset a/b ,And, Green is 1-24 single mode. You may press and down the relevant Flash button Scene to trigger the button Momentarily.

PLAYING A SCENE TO AUDIO TRIGGERING Action

1) Select your as Scene as described in the above section.

2) Tap the Audio button until LED lights, indicating AUDIO mode is active.

3) Use the Audio Level slider to adjust the sensitivity.

4) To return to normal mode, tap the Audio button a second time, causing its LED to go out. AUDIO mode is disengaged. NOTES: This is the process of using the built-in microphone, or using the audio jack on the controller to use an alternative audio source for triggering of Scenes.

USER MANUAL

11/19

DMX 512 CONTROLLER SERIES

PLAYING A SCENE WI TH THE SPEED SLI DER Action

1) Select your Scene as described in the above sections

2)Move the Speed slider to SHOW MODE position (fully down).

3)Press and hold the Rec Speed button & tap the corresponding Flash button (13-24). The Scene tapped will no longer run with the standard beat

4)Now, you may move the Speed slider to select your desired speed.

PLAYING A SCENE WI TH THE STANDARD BEAT Action

1) Tap the Mode select button to select Chase ..Scene mode.

2) Tap the Park button to select Mix Chase mode. The LED lights, indicating the selection.

3) Select your Scene as described in the previous sections.

4) Move the Speed slider until the display reads your desired value.

5) Press and hold Rec Speed button & tap the Flash button (13-24) to store the Scene. The Scene will now run with the set time or beat when engaged.

6) Repeat steps 4 & 5 to set a new beat time.

Notes

Be sure AUDIO mode is disengaged. As an alternative to using the Speed slider to input the speed, you may use the Tap sync button (2) times to define your beat.

CHANGE THE SPEED MODE BETWEEN 5 & 10 MI NUTES Action

1) Press and hold the Record button.

2) Tap the Flash button 5 or 10 three times

3) The 5min or 10min LED should light, indicating the Speed the slider is set to run.

AUXILIARY CONTROLS

This is the process of assigning the Auxiliary controls. These will act as shortcuts and are most commonly used for DMX strobe lights or DMX fog machines. However, they are not limited to these functions, such as Pan/tilt control-very useful for remote follow spot controls.

Action

1) Press & hold RECORD & tap the Flash button 7 or 8 (3) times. The display should indicate activation of the mode.

2) There are 3 functions. FUNC 1 states that the Auxiliary control is not assigned to any channel. FUNC 2 refers o the auxiliary controls working much like the channel fader along with the flash buttons. FUNC 3 is somewhat different. The rotary knob acts to set the total output of the flash button below it.

3)While holding down the RECORD button, select the function you wish for the auxiliary control by pressing Flash button 1, 2, or 3. Release the buttons.

4)To assign the auxiliary to a channel, press the Flash button for the channel you wish to assign the auxiliary control to. This sets the channel assignment. The corresponding Led above the channel will light, indicating that the channel has ben assigned.

5) Record exit.

Notes

You may refer to the display for the functions being edited. Press 7 (3) times for AUX 1 patching, and 8 (3) times for AUX 2 patching. While assigning an auxiliary to mode 2, the Fader for that channel will not function. It will act as moving the channel. While assigning an auxiliary to mode 3, the channel fader and the auxiliary controls will both work for that channel on an HTP (highest takes precedent) operating principle.

Midi Operation

The controller will only respond to MIDI commands on the MIDI channel that it is assigned to. All MIDI control is performed using Note on commands. All other MIDI instructions are ignored. To stop a chase, send the blackout on note.

USER MANUAL

12/19

DMX 512 CONTROLLER SERIES

Setting MIDI IN

Action

1) While holding down the RECORD button, simultaneously tap to Flash button #1 three times. The display reads MIDI CHANNEL IN to indicate channel setup is available.

2) Select the MIDI control channel (1-16)by tapping Flash button 1-16.The relevant channel LED lights indicating MIDI IN channel is est.

3) While holding down RECORD, tap the REC EXIT button to exit MIDI setting.

MIDI Note

27-69 70-93

94 95 96 97 98

99 100 101 102

Notes: This is the Channel that the controller will receive MIDI note commands. Notes: When working with MIDI notes 22-93,you may simulate a faders incease

and decrease by adjusting the velocity of the note.

FUNCTION (TURN ON/OFF)

Tum on or off program 1-48

Activate Channel 1-24

FULL-ON

DARK(momentary blackout)

HOLD

Tum on or off AUDIO

Chase SCENE

MODE:1-12A-1-12B

MODE:1-24A

BACKOUT

Setting MIDI OUT

Step

Action

4) While holding down the RECORD button, simultaneously tap Flash button #2 three times. The display reads MIDI CHANNEL OUT to indicate channel setup is available.

5) Select the MIDI control channel (1-16)by tapping Flash button 1-16.The relevant lights indicating MIDI OUT channel is set.

6) While holding down RECORD, tap the REC EXIT Button to exit MIDI setting.

Notes: This is the channel that the controller will transmit MIDI note commands.

Receiving MIDI File Dump

Action

7) While holding down the RECORD button, simultaneously Flash button #3 three times. The display reads MIDI FILEDUMP RECVING 000%wen the device is in the correct mode.

USER MANUAL

13/19

DMX 512 CONTROLLER SERIES

8) While holding down RECORD, tap the REC EXIT button to exit MIDI setting.

Notes: This is process of copying show to another same 48 CH dimmer console. This will not work with any other device. This process can take several minutes to complete. This control will automatically being the FILE DUMP once the mode has been selected. Therefore, be sure that the other deceive has preciously been setup to receive the transfer. During FILE DUMP, all other operation will cease to function. If errors or power failure occurs, FILE DUMP will be interrupted and stop.

Sending MIDI File Dump

Action

9) While holding down the RECORD button ,simultaneously tap Flash #4 three times, the display reads MIDI FILE DUMP SENDING 000%when the device is in correct mode.

10) While holding down RECORD, tap the REC EXIT button exit MIDI setting.

Notes: This is the process of copying your entire show to another same 48CH dimmer console . This will not work with any other device. This process can take several minutes to complete . The control will automatically being the FILE DUMP once the mode has been selected. Therefore, be sure that the other device has previously been setup to receive the transfer. During FILE DUMP, alI other operations will cease to function . If errors or power failure occurs, FILE DUMP will be interrupted and stop.

6.APPEMDIX

DMX Primer

There are 512 channels in a DMX 512 connection. Channel may be assigned in any manner. A fixture capable of receiving DMX 512 will require one or a number of sequential channels .The user must assign starting address on the fixture that indicates the first channel reserved in the controller . There are many different types of DMX controllable fixture and they all may vary in the total number of channels required, Choosing a start address should be planned in advance, Channels should never overlap. If they do ,this will result in erratic operation of the fixture s whose starting address is set incorrectly. You can however, control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation, In other words, the fixture will be slaved together and all respond exactly the same.

USER MANUAL

14/19

DMX 512 CONTROLLER SERIES

DMX fixtures are designed to receive data though a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fiture.The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling .Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors, The

shield connection is pin 1, while pin 2 is Data Negative (S-)and pin 3 is Data positive(S+)

FIXTURE LINKING

Occupation of the XLR-connection:

DMX-OUTPUT

XLR mounting-socket:

XLR mounting-plug:

DMX-OUTPUT

120 ohm

1- Ground 2 - Signal (-) 3 - Signal (+)

PIN2

PIN3

Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 resistor between Signal (-) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX

terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120W (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.

The transform of the controller line of 3 pins and 5 pins (plug and socket)

General Troubieshooting

Symptom

Auto shut off

Beam is very dim or nor bright

Breaker/Fuse keeps biowing

Solution(S)

Check fan thermal switch reset

Check optical system or tepiace lamp Check 220V/110V switch for proper setting

Check total load on device

lights

Applies to

Foggers & Snow

controllers

USER MANUAL

Dimmers& chaser

15/19

DMX 512 CONTROLLER SERIES

Chase is too slow

Device has no Power

Fixture is not responding

Fixture is on but there is no movement to the audio

Lamp cuts off

Sporadically

Light will not come on after power failure

Check users manual for speed adjustment

Check for power on mains. Check device S fuse.(intemal and/or external)

Check DMX Dip switch setting for Correct addreesing Check DMX cables Check polarity switch settings

Make sure you have the correct

audio mode on the control switches.

If audio provided via1/4 jack make

suer a live audio signal exists.

Adjust sound sensitivity knob.

Possible bad lamp or fixture is

Overheating.

Lamp may be lamp end of its life.

Some discharge lamps require a

cooling off period before the

electronics in the fixture can kick

Loss of singnal

Moves slow

No flash

No light output

Relay will not work

Remote does not work

Stand alone mode

Start it again, wait 5 to 10 minutes Before powering up.

Use only DMX cables

Install terminator

Note: Keep DMX cables separated

From power cables or black lights.

Check 200V/11V switch for proper

Setting.

Re-install bulb, may have shifted in

Shipping, readjust

Bounce mirror motor may have Shifted during shipping

Check slip ring & brushes for contact

Install bulb

Call service technician

Check reset switch

Check cable connections

Make sure connection is firmly

connected to device All lighting fixtures featuring

Standalone function do not require

additional settings, simply power the fixture and it will automatically enter into this mode

USER MANUAL

16/19

DMX Dipswitch Quick Reference Chart

DMX Address Quick Reference ChartDMX Address Quick Reference Chart

DMX 512 CONTROLLER SERIES

Dip Switch Position

DMX DIP SWITCH SET

0=OFF

1=ON

X=OFF or ON

#1 #2 #3 #4 #5

#9 0 #8 #7 #6

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 63

0 0 1 1 1

1 1 1

64 96

65 97

66 98

67 99

68 100 132 164 196 228 260 292 324 356 388 420 452 484

94 95

128 160 192 224 256 288 320 352 384 416 448 480 129 161 193 225 257 289 321 353 385 417 449 481 130 162 194 226 258 290 322 354 386 418 450 482 131 163 195 227 259 291 323 355 387 419 451 483

101 133 165 197 229 261 293 325 357 389 421 453 485 102 134 166 198 230 262 294 326 358 390 422 454 486 103 135 167 199 231 263 295 327 359 391 423 455 487 104 136 168 200 232 264 296 328 360 392 424 456 488 105 137 169 201 233 265 297 329 361 393 425 457 489 106 138 170 202 234 266 298 330 362 394 426 458 490 107 139 171 203 235 267 299 331 363 395 427 459 491 108 140 172 204 236 268 300 332 364 396 428 460 492 109 141 173 205 237 269 301 333 365 397 429 461 493 110 142 174 206 238 270 302 334 366 398 430 462 494 111 143 175 207 239 271 303 335 367 399 431 463 495 112 144 176 208 240 272 304 336 368 400 432 464 496 113 145 177 209 241 273 305 337 369 401 433 465 497 114 146 178 210 242 274 306 338 370 402 434 466 498 115 147 179 211 243 275 307 339 371 403 435 467 499 116 148 180 212 244 276 308 340 372 404 436 468 500 117 149 181 213 245 277 309 341 373 405 437 469 501 118 150 182 214 246 278 310 342 374 406 438 470 502 119 151 183 215 247 279 311 343 375 407 439 471 503 120 152 184 216 248 280 312 344 376 408 440 472 504 121 153 185 217 249 281 313 345 377 409 441 473 505 122 154 186 218 250 282 314 346 378 410 442 474 506 123 155 187 219 251 283 315 347 379 411 443 475 507 124 156 188 220 252 284 316 348 380 412 444 476 508 125 157 189 221 253 285 317 349 381 413 445 477 509 126 158 190 222 254 286 318 350 382 414 446 478 510 127 159 191 223 255 287 319 351 383 415 447 479 511

1 0 0 1 1

1 0

1 1 1 1

1 1 1

Dip Switch Position

DMX Address

USER MANUAL

17/19

Technical Specifications

WEIGHT & DIMENSIONS

Length Width Height Weight

POWER

Operating Adapter

THERMAL

Maximum ambient temperature

DMX 512 CONTROLLER SERIES

(485 mm)

(290 mm)

(98 mm)

(5 kg)

DC 9V 1000ma 100-240v autos witching

2-pin Edison

104 F(40 )

CONTROL &PROGRAMMING

3-pin DMX:

Data output Data pin configuration Protocols

Locking 3-pin XLR female socket

Pin 1 shield, pin 2 ,pin 3(+)

DMX-512 USITT

USER MANUAL

18/19

DMX 512 CONTROLLER SERIES

Appendix: Quick operation

Manual operation

1) Connect to power, Press BLACK OUT and it Os yellow LED light OF

2) Move sliders of MASTER A and FADE to top.

3) Use MODE SELECT to select 1-24 SINGLE mode

4) Move sliders to change DMX value to control lighting fixture.

Program

1, Connect to power, Press BLACK OUT and it Os yellow LED light OF 2, Move sliders of MASTER A and FADE to top. 3, Use MODE SELECT to select 1-24 SINGLE mode

3.1 - Edit Scene

3.1.1: Keep pressing RECORD and press FLASH button 1-5-6-8 to ente PROGRAM stat us. RECORD LED ON. 31 .2: Move sliders of channels to get suitable effect

3.1.3: Press RECORD to save current effect ( all LED lamps of slider area will flash one time). LCD display bottom line show [STEP NO 001]

3.1.4: Repeat step 3.1.2 & 3.1.3 to program scene you need.

3.2 - Save scene to program slider:

3.2.1: Press PAGE to select program page -- total 1-4 pages, 12 program sliders each page)

3.2.2: Keep pressing RECORD and correspond FLASH button of 13-24 sliders (all LED lamps of slider area will flash one time). Then current scene be saved to selected program slider.

3.2.3: Repeat steps 3.1.2, 3.1.3, 3.1.4, 3.2.1, 3.2.2 to edit and save other program sliders.

Run program

1, Press MODE SELECT to get CHHASE SCENES and select running mode

2, Press PAGE to select running program page. 3, Move sliders of correspondent running program channel (13-24) to top and it Os yellow LED lamp ON 4, Move SPEED slider to set program FADE IN time. 5, Press PARK B to select SINGLE CHASE (- Recycle mode and it Os red LED lamp ON) or MIX CHASE(- run all selected program at same time and it Os yellow LED lamp light up)

USER MANUAL

19/19

AVSL DM-X24 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual