AMD SERIES
CAUTION
Please read through this manual carefully before use. This product is strictly for indoor
use only, please install this product in dry and cool environment and keep out of the
reach of children and pets.
Please do not open cover, contain high voltage. This
product is not serviceable or repairable by end user. Please
return to dealer for repair
4G READY AERIAL
DISTRIBUTION AMPLIFIERS
Item ref: 130.030UK, 130.031UK,
130.032UK, 130.033UK
User Manual
INTRODUCTION:
AMD02
AMD04
AMD06
AMD08
Item ref
130.030UK
130.031UK
130.032UK
130.033UK
No of inputs
2 2 2
2
No of outputs
2+Full
4+Full
6+Full
8+Full
Frequency
response
47-300MHz,
470-862MHz
47-300MHz,
470-862MHz
47-300MHz,
470-862MHz
47-300MHz,
470-862MHz
Max output level
94dBµV
90dBµV
87dBµV
87dBµV
Gain per split
12dB
8dB
8dB
8dB
Gain on Full
20dB
20dB
20dB
20dB
Noise
<4dB
<4dB
<4dB
<4dB
Isolation loss
22dB
22dB
22dB
22dB
Dimensions
134.5 x 70 x
44.4mm
179.5 x 70 x
44.4mm
224.5 x 70
x 44.4mm
269.5 x 70
x 44.4mm
Weight
270g
350g
420g
500g
Thank you for choosing Mercury AMD series distribution amplifier. It is designed to amplify weak
FM/DAB/TV aerial from aerial and distribute to multiple outputs, ideal for domestic or commercial use
to distribute FM/DAB/DTV(DVB-T, ATSC, ISDB, T-DMB)/Sat signal to different room/area.
PRODUCT FEATURES:
- Separate dedicated inputs for VHF and UHF signal.
- Built in low noise high gain amplifier to boost weak signals from aerial.
- Built in mixer to give wideband VHF and UHF output.
- Integrated LTE signal filter avoids interference and channel loss from 4G mobile signal.
- Full gain output to for a long cable run.
- DC pass allows the control of satellite via Magic Eye remote extender (124.157UK)
- Built in surge and short circuit protection, and maximum output limiter prevents overload.
SPECIFICATION:
INSTALLATION:
Before installing please ensure all devices to be connecting to the amplifier are switched off and
disconnected to the mains. The unit is designed to be connected via “F” connectors for secure
connections, for coax connector (RF/IEC 169-2/Belling-Lee), a coax to “F” connector adaptor will be
required. At the back of the case there are two mount holes which allow unit to be wall mounted.
AMD distribution amplifiers are designed to amplify weak signals and distribute them to different
locations. For installations that are close to TV transmitters, some user may experience blocking or a
frozen picture. An attenuator may be required to reduce the input signal to the amplifier.
AMD Series User Manual
EXAMPLE INSTALLATION:
This diagram shows AMD08 receiving TV signals from the Sat receiver and FM/DAB aerial and
distributes signals to 4 individual hi-fi and TV units. AMD series amplifiers are designed with DC pass
function. All 4 TV units can be set up with “Magic eye” (remote extension unit) to allow remote
control of Sat receiver when TV set is not at the same room as the Sat receiver. This can only be
done when connect the RF2 output to the UHF input of the amplifier.
Please note: only one sat channel can be viewed at any particular time from the Sat receiver. AMD
series amplifiers do not require setup to operate, for Sat receiver set up please refer to your Sat
receiver manual.
AMD Series User Manual
It is also suitable for upgrading or replacing existing UHF/VHF signal distribution unit, simply
reconnect existing connecting from previous unit to the AMD amplifier. Ensure the UHF aerial is
connected to the UHF input of the amplifier and FM/DAB aerial connected to the VHF input of the
amplifier. For loft distribution installation please ensures the unit is kept away from moisture and heat
sources.
TVs that are not compatible with digital TV will require a digital set top box for TV viewing.
This product is classed as Electrical or Electronic equipment and should not be disposed
with other household or commercial waste at the end of its useful life. The goods must be disposed of
according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2014. AVSL Group Ltd
AMD Series User Manual
Loading...