Avocent UMG-2000, UMG-2100, UMG-2200 Quick Installation Manual

Unied Ofce Gateway

UMG-2000 / UMG-2100 / UMG-2200

Version: 1.1

Quick Installation Guide

Table of Contents

1. Package Contents ........................................................................................ 3

2. Overview .................................................................................................... 4

3. Hardware Installation ................................................................................... 6

3.1 Unpack the UMG-2000 / UMG-2100 / UMG-2200 ..................................... 6

3.2 Choosing a Setup Location..................................................................... 6

3.3 Preparing for Setup ............................................................................... 7

3.4 Precautions .......................................................................................... 7

3.5 Installation Consideration ....................................................................... 7

3.6 The Desktop Brackets Installation ........................................................... 8

3.7 The Rack Mount Installation ................................................................... 8

3.8 The Hard Disk Installation ..................................................................... 9

4. Physical Connection .................................................................................... 11

4.1 WAN Connection ..................................................................................11

4.2 LAN Port Connection ............................................................................11

4.3 PSTN FXO Port Connection....................................................................12

4.4 ISDN T1/E1 Port Connection .................................................................12

5. Quick Setup Wizard ....................................................................................13

5.1 First Time Login ................................................................................... 13

5.2 Welcome to Quick Start ........................................................................14

Further information ......................................................................................... 20

1. Package Contents

UMG-2000 / UMG-2100 /UMG-2200 Unit x 1 l

AC Power Cord x 1 l

CD x 1 l

Quick Installation Guide x 1 l

Ear Brackets x 2 l

Desk Brackets x 2 l

Brackets Fixing Screws x 12 l

Plug Screws x 4 l

Disk Carrier Screws x 25 l

Antennas x 2 l

If any of above items are damaged or missing, please contact your dealer
immediately.

3

4

2. Overview

Front Panel

1 PWR LED

2 Internet LED

3 PBX LED

4 WLAN LED

5 E-mail LED

6 Firewall LED

7 Alert LED

8 1~24 LED

9 25~26 LED

10 FTX LED

On Power On

Off Power Off

On Connect to Internet

Off Disconnect to Internet

On PBX function turn on

Off PBX function turn off

On Wireless function turn on

Off Wireless function turn off

On E-mail function turn on

Off E-mail function turn off

On Firewall/Security function turn on

Off Firewall/Security function turn off

On Don’t insert or pull put hard disk

Off Normal status

On Connect to 1~24 10/100Mbps LAN ports

Off Disconnect to 1~24 10/100Mbps LAN ports

On Connect to 25~26 10/100/1000Mbps LAN ports

Off Disconnect to 25~26 10/100/1000Mbps LAN ports

Fault redundant unit is connected and

On

activated(future feature)

Off Fault redundant unit is not available (future feature)

5

On Branch to Branch SSL VPN secure link is established

11 BTB LED

Storage 1~4

12

LED

Disk Carrier

13

Handler

14 Disk Carrier switch Press the button to pop out the SATA carrier

Branch to Branch SSL VPN secure link is not

Off

enabled or disconnected

On Read/Write data in the hard disk

Off Don’t Read/Write data in the hard disk

Push the handler to lock the carrier. Unlock and pull
the hander to get the carrier out

Rear Panel

1 Cooling Fans System cooling fans on rear panel

UMG-2000 : 4 x RJ-11 (4 x FXO)

2 Voice (P1)

3 Wireless (P2)

4, 5 LAN

6 WAN

7 USB 2 x USB2.0 (future feature)

8 Cooling Fan Power supply cooling fan

9 AC PWR

UMG-2100 : 1-Port T1/E1 PRI
UMG-2200 : 8 x RJ-11 (8 x FXO)

1 x 802.11b/g/n Wireless Access Point, 2 x Antenna
Detachable

1~24 ports: 24 x RJ-45 (10/100Base-TX, Auto­Negotiation, Auto MDI/MDI-X)
25~26 ports: 2 x RJ-45 (10/100/1000Base-T, Auto­Negotiation, Auto MDI/MDI-X)

1 x RJ-45 (10/100Base-TX, Auto-Negotiation, Auto MDI/
MDI-X)

100~127V AC 6.3A, 200~240V AC 3.0A, 50/60 Hz, 200
Watts

6

3. Hardware Installation

Note

3.1 Unpack the UMG-2000 / UMG-2100 / UMG-2200

You should inspect the box which the system was shipped in and
note if it was damaged in any way before the unpacking. If the
UMG-2000 / UMG-2100 / UMG-2200 itself shows damage you
should file a damage claim with the carrier to who delivered it.
Unpack the UMG-2000 / UMG-2100 / UMG-2200 as listed below.

3.2 Choosing a Setup Location

Decide on a suitable location for the UMG-2000 / UMG-2100 / UMG-2200 which
should be situated in a clean, dust-free, and well ventilated area. Avoid areas

where heat, electrical noise and electromagnetic elds are generated. Place

the UMG-2000 / UMG-2100 / UMG-2200 near a grounded power outlet and pay
attention to the following requirements.

 Leave approximately 40cm (16inche) of clearance in front of the UMG-2000 /

UMG-2100 / UMG-2200 to ensure the disk carriers can be unplugged.

 Leave approximately 30cm (12 inch) of clearance in the back of the UMG-2000

/ UMG-2100 / UMG-2200 to allow for sufcient airow and ease in servicing.

7

3.3 Preparing for Setup

The UMG-2000 / UMG-2100 / UMG-2200 system was shipped with desk brackets,
ear brackets, and mounting screws, so it is possible to install the UMG-2000 /
UMG-2100 / UMG-2200 into the mounted rack or on the desk brackets. Please read
following sections in its entirety before you begin the installation and follow the
steps in the order given to complete the installation process correctly.

3.4 Precautions

 Review the electrical and general safety precautions.

 Install the heaviest server components on the bottom of the rack rst, and then

work up if you want to mount the UMG-2000 / UMG-2100 / UMG-2200 to a
rack.

 Use a power supply regulating uninterruptible (UPS) to protect the server from

failure.

 Allow the hot plug SATA drives and power supply units to cool before touching

them.

 Always keep the rack’s front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

3.5 Installation Consideration

AMBIENT OPERATING TEMPERATURE

If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature.

REDUCED AIRFLOW

Consideration should be given to the amount of airow required for safe operation

maybe not compromised for the rack mounting.

CIRCUIT OVERLOADING

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on over-current protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

RELIABLE GROUND

A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).

8

3.6 The Desktop Brackets Installation

Unpack the UMG-2000 / UMG-2100 / UMG-2200. l

The desk brackets have been xed to the device before packing. l

Place the system to appropriate site. l

3.7 The Rack Mount Installation

It is strongly recommended to securely fasten the mounting rack to the oor or

wall to eliminate any possibility of tipping over the rack. This is especially important
if you decide to install several UMG-2000 / UMG-2100 / UMG-2200 chassis in the
top of the rack.

A brief overview of the UMG-2000 / UMG-2100 / UMG-2200 installation is as
follows:

Select an appropriate site in the rack. l

Unload 4 the plug screws from each side of the server. l

Mount the ear brackets to the server from the each side. l

9

Mount the server into the rack. l

Note

Lock the server to the rack by mounting the ear brackets to the rack. l

3.8 The Hard Disk Installation

The SATA subsystem supports four hot-swappable hard drives. The SATA drives are
inserted to the SATA backplane that provides power and bus termination.

1. Please install at least one 80G HDD to the No.1 disk carrier
before system configurations.

2. If with single HDD, please select RAID level to JBOD.

10

Locate the storage subassembly. l

Press the disk carrier switch to unlock the carrier. l

Unplug the disk carrier by pulling the carrier handler. l

Mount the disk into the carrier and load the xing screws. l

Press the disk carrier switch to insert the carrier to the disk slot. l

Close the disk carrier lock/switch to lock the carrier. l

11

4. Physical Connection

4.1 WAN Connection

Locate the WAN port on the rear panel. l

Connect the WAN port with the Ethernet cable. l

4.2 LAN Port Connection

There are 26 Ethernet ports on the rear panel. The port 1 to 24 are 10/100 l
Mbps Ethernet ports and the port 25 and port 26 are 10/100/1000 Ethernet
ports.

It is recommended to connect the third party switches to the port 25, 26 to l
expand the LAN ports.

12

4.3 PSTN FXO Port Connection

Locate the voice port of the PSTN adapter on the rear panel. l

The Analog PSTN port may vary from 4 / 8 FXO ports. l

Connect one or more telephone cables to one of the selected FXO port. l

4.4 ISDN T1/E1 Port Connection

Locate the digital voice port of the T1/E1 adapter on the rear panel. l

Connect the ISDN network with the T1/E1 port. l

13

5. Quick Setup Wizard

From this chapter, we will describe how to use PLANET View to congure and

control the UMG-2000 / UMG-2100 / UMG-2200 features and setup IT services

conguration. PLANET View enables you easily navigate through all IT congurations

and services.

5.1 First Time Login

Now that the network connection between your PC and UMG-2000 / UMG-2100 /
UMG-2200 has been established, you must login in order to access PLANET View.

Launch a web browser (for example: IE, Firefox etc.) and type the UMG-2000
/ UMG-2100 / UMG-2200 IP address in the address bar. The default address is
“http://192.168.1.1”.

If you can not see the following login page, recheck your physical LAN connection
and repeat Section “LAN Connection”. To avoid web-based management abused
by unauthorized users, the login sessions will logout automatically if the session is
inactive for more than 5 minutes. Type in an authorized username and password
and then click the button ”Apply”. The default username is “admin”, and its
password is “admin” all in lower case.

14

5.2 Welcome to Quick Start

After the rst login, an easy and short quick start up should be completed to make

the UMG-2000 / UMG-2100 / UMG-2200 service normally. There is an alternative
selection in the page “Welcome”. One selection is for “Quick Start” and the other
is for “Faster Recovery UMG to UMG” which will be explained in the user’s manual.

The quick start includes ve steps which will lead administrator to setup the
UMG-2000 / UMG-2100 / UMG-2200. Check the rst radio box and then click the

button “Start” to continue.

Step 1: Create the Company Prole

This page allows an administrator to build a company prole. Specify the prole

and then click the button “Next” to go to step 2.

Item Description

Company Specify your company name.

Location Specify your city name.

Country Specify your country name.

Time Zone Specify the time zone.

PBX
Extension

Specify the prex of the extensions. All PBX extensions will be
prexed with this number. (X=0~9).

15

Step 2: Activating UMG-2000 / UMG-2100 / UMG-2200 services

The UMG-2000 / UMG-2100 / UMG-2200 allow the administrator to activate the
service on demand. By default, all services are inactive. The administrator can
activate the service in this page by checking the radio box of the corresponding

service. The activated services will start up by using the default conguration after

the quick start. Click the button “Next” to go to step 3.

Item Description

PBX Enable or disable the IP PBX service.

PPTP VPN Enable or disable the PPTP VPN service.

Email Enable or disable the Email service.

Network Storage Enable or disable the network storage service.

Internet Domain
Name

Specify a valid Internet domain for the email server if the
email service is enabled.

Step 3: Setting up the Internet Connection

This page allows the administrator to quickly setup the WAN connection. To setup
the Internet connection, you should be awarded of what method you are using
to connect to the Internet. All technical information should be provided by your
Internet Service Provider (ISP). The ISP type should be one of the followings:
static, DHCP, PPPoE or PPTP. Select your ISP type in the drop down menu. Specify

the Internet connection conguration and then click the button “Next” to go to step

4 or click the button “Skip” to skip this step.

16

AUTO DETECT ISP TYPE

By clicking the button “Detect”, you can make the UMG-2000 / UMG-2100 /
UMG-2200 to recognize the ISP type automatically.

It may take a while to detect your ISP type. Please wait.

The ISP type will be detected and the result will be presented as follows. If
“Network Cable Disconnected” is detected, please recheck the physical connection
and repeat the action as shown in Section “WAN Connection”. There could be more
than one ISP type recognized, so choose the most suitable type from the list and
then click the button “Next” to continue.

17

MANUAL SETUP INTERNET CONFIURATION: STATIC

If your ISP type is “Static”, choose it as your ISP type and setup the conguration.

Item Description

IP Address Specify the static IP address.

Subnet Mask Address Specify the subnet mask address.

Default Gateway Address Specify the IP address of the default gateway.

DNS Server Address

MAC Address Show MAC address information.

MANUAL SETUP INTERNET CONFIURATION: DHCP

If your ISP type is “DHCP”, choose it as your ISP type and setup the conguration.

Specify the IP address of the primary and
secondary Domain Name System.

Item Description

DNS Server Address

MAC Address Show MAC address information.

Automatically obtain the DNS address or specify the
IP address of the primary and secondary DNS server.

18

MANUAL SETUP INTERNET CONFIURATION: PPPOE

If your ISP type is “PPPoE”, choose it as your ISP type and setup the conguration.

Item Description

Login Name Specify the login username to the PPPoE server.

Password Specify the login password to the PPPoE server.

Conrm Password Retype the password.

Static IP Address Specify whether you have a static IP address.

IP address

Subnet Mask Address

DNS Server Address

MAC Address Show MAC address information.

MANUAL SETUP INTERNET CONFIURATION: PPTP

If your ISP type is “PPTP”, choose it as your ISP type and setup the conguration.

Specify your static WAN IP address if you have
enabled the “Static IP Address”.

Specify the subnet mask address if you have
enabled the “Static IP Address”.

Automatically obtain the DNS address or specify
the IP address of the primary and secondary DNS
server.

19

Item Description

PPTP Server Specify the PPTP server IP address.

Login Name Specify the username to login to the PPTP server.

Password

Conrm Password Retype the password.

Static IP Address Specify whether you have a static WAN IP address.

IP address Specify whether you have a static IP address.

Subnet Mask
Address

DNS Server
Address

MAC Address Show MAC address information

Step 4: Setting the Wireless Network

This page allows the administrator to quickly setup the wireless Access Point (AP).

Specify the wireless conguration and then click the button “Next” to go to step 5.

Specify the corresponding password to login to the PPTP
server.

Specify your static WAN IP address if you have enabled
the “Static IP Address”.

Specify the subnet mask address if you have enabled the
“Static IP Address”.

Item Description

Access Point (AP) Enable or disable the wireless AP service.

Hide SSID

Network Name (SSID) Specify the preferred SSID name string.

Wireless Region Select the area of location yours.

Wireless Mode

Channel Select the preferred wireless channel number.

Authentication Type

Data Encryption Select the Data Encrypt type.

Encrypt Strength Select the encrypt strength.

Security Key Specify the key for the clients to access this AP.

Decide whether or not to make the wireless AP SSID
visible.

Select the preferred wireless AP mode:

802.11b / 802.11g / 802.11n.

Specify the authentication type:
Open system / Shared Key / WPA / WPA2.

Step 5: Creating the Network Storage

This page allows the administrator to quickly setup the storage. Specify the
Redundant Array of Independent Disks (RAID) level and then click the button
“Next” to go to step 6.

Step 6: Conrmation

Please recheck your input data to ensure the accurate. Click the button “Back” to

make changes. Then conrm your data and wait for the accomplishment of the

wizard. It will take a couple of minutes. Please “do not” close the browser. The

browser will show the RAID building progress. After nishing the wizard successfully,

the page of “Personal Account Web Administration” will automatically appear.

Further information

For further detail congurations and information can be found in the user’s manual CD.

Chapter 6: Wireless Chapter 7: Storage Chapter 8: PBX
Chapter 9: Email Chapter 12: Security Chapter 14: Branch-to-Branch

If you have other questions, please contact the local dealer where you purchasing
this product.

20