Avocent SC4UAD-001 User Manual

The following will help you install your

SwitchView SC4 UAD switch easily.

Should you require further assistance, please

contact Avocent Technical Support.

Connecting local peripherals

Turn off all servers that will be part of your

SwitchView SC4 UAD switching system. Locate

your USB keyboard, DVI monitor, USB mouse,

speakers and microphone.

cable into the appropriate CONSOLE port on

the left side of the back of your switch

USB keyboard cable and your USB mouse cable

into the keyboard and mouse ports respectively.

Plug your speaker cable and microphone cable

into the corresponding ports.

Plug your DVI monitor

. Plug your

The Power of Being There

Quick Installation Guide

SwitchView® SC4 UAD

DVI/USB Switch with Audio

To install the SwitchView SC4 UAD switch

Optional

RF ground

(not required for

safety)

Connecting your servers

Locate your ﬁrst cable set consisting of one USB

cable, one DVI cable and two audio cables. The

SwitchView SC4 UAD switching system has four

port sets labeled A-D on the rear of the unit. Plug

the USB cable, the two audio cables (speaker

and microphone) and the DVI cable (monitor)

into the corresponding ports on your server.

Plug the other ends into any of the available server

port sets on your SwitchView SC4 UAD switch.

Repeat this process until all servers are properly

attached to the SwitchView SC4 UAD switch.

NOTE: Cable sets without audio cables are

available if you do not require speaker and

microphone support.

Powering your system

Locate the power cord that came with your

switch. Plug one end into the IEC power connector on

the SwitchView SC4 UAD switch. Ensure the power

switch is off, then plug the other end of the power

cord into an AC wall outlet. Turn on your switch ﬁrst,

then turn on all attached servers.

Switching your servers

Press the appropriate front panel button labeled A-D to

access servers in your SwitchView switching system.

LEDs

Each target port (A-D) has a single bi-color LED on the front

panel. The LED will be green when the target device is on

and connected to the switch. The LED will change to amber

when the target device is selected (KVM session).

Mechanical

H x W x D = 1.75” x 11” x 11” (4.44 x 27.94 x 27.94 cm)

Weight = 4.9 lbs (2.2 kg)

Environmental

Operating Temperature: 41˚ (5˚C) to 104˚ (40 ˚C)

Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)

Input Power: 60 W; Operating Voltage 100-240 VAC

Power Frequency: 50-60 Hz

Supported Hardware

Server: IBM, Sun, PC/AT, USB and 100% compatibles

Video Modes: VGA, SVGA, XGA, SXGA, UXGA,

WVGA, WSVGA, WXGA, WSXGA, WUXGA,

and HDTV

Maximum resolution: Single link DVI up to

1920 x 1200 @ 60Hz (monitor and video card support

for the maximum resolution will vary and should be

veriﬁed for compatibility)

Peripherals: USB keyboard, USB mouse and

IntelliMouse (USB only)

To Contact Avocent Technical Support: Visit www.avocent.com

Avocent, the Avocent logo, The Power of Being There, the Cybex logo and SwitchView are registered trademarks of Avocent Corporation or its afﬁliates. ©2007 Avocent Corporation. All rights reserved. 590-609-501B

USA Notiﬁcation

Canadian Notiﬁcation

Japanese Approval

Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Safety and EMC

Approvals and Markings

UL, FCC, cUL, ICES-003, CE, VCCI, C-Tick

Safety certiﬁcations and EMC certiﬁcations for this product are obtained under one or more of the following

designations: CMN (Certiﬁcation Model Number), MPN (Manufacturer’s Part Number) or Sales Level Model

designation. The designation that is referenced in the EMC and/or safety reports and certiﬁcates are printed on the

label applied to this product.

Safety Precautions

DANGEROUS VOLTAGE

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

NOTE: The AC inlet is the main disconnect.

INSTRUCTIONS

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions.

WARNING : To reduce the risk of electric shock or damage to your equipment:

- Do not disable the power grounding plug. The grounding plug is an important safety feature.

- Plug the power cord into a grounded (earthed) outlet that is easily accessible at all times.

- Disconnect the power from the switch by unplugging the power cord from either the electrical outlet or the appliance.