1 2 3
A
Genius Plus
Installation Instructions
Imaging Technology
MOUNTING LOCATION
Choose a location most likely to intercept an
intruder. See the detection patterns in Fig. 5.
The twin dual element high quality sensors
detect motion across the beam field; they are
slightly less sensitive to motion towards the
detector.
While the GENIUS PLUS is capable of detecting
intrusions under exceedingly difficult conditions,
it is recommended to avoid the following
locations:
• Areas where sunlight may shine
directly onto the PIR (lens).
• Facing surfaces that may change
temperature extremely rapidly.
• Areas with extreme airflows.
NOTE: Recommended installation
height is at 2.4m (7.9ft).
The circular and rectangular indentations at
the bottom base are the knockout hole for wire
entry. You may also use mounting holes that
are not in use for running the wiring into the
detector.
To close the front cover, insert the two small
prongs along its upper edge into their
corresponding slots in the upper edge of the
base. Insert the larger prong at the bottom of
the front housing into the slot at the bottom of
the base by exerting slight pressure on the
prong. The front cover should now fit snugly
into the base.
For detector installation it is
recommended to use set of
plastic anchors supplied with
Caution: using different or
bigger screws can damage the
internal electronic board.
Double Linear
PIR Sensor
4 5 6
7 8 9
the detector.
GENERAL DESCRIPTION
This Double Quad Element PIR detector is
based on the latest “ASIC” (Application Specific
Integrated Chip) and SMD technologies.
The Genius Plus monitors the environment by
analyzing the conditions and adapts to it
constantly. If conditions change, the GENIUS
PLUS adapts it maintaining sensitivity levels and
detection capability.
By using Double Quad Optic Systems with a
diagonally opposed configuration (phase shift
discrimination), the GENIUS PLUS is able to
achieve a three dimensional thermal image of
the protected area. It stores this image and
refers to it determine intrusions.
During the standby mode (no LED indications)
the GENIUS PLUS constantly monitors the
protected area, updating and reconfiguring itself
as conditions change.
FIG. 1 – REMOVING THE FRONT COVER
FIG. 2 - OPTIONAL HOLES
The plastic base include different types of
knockdown holes:
. Wire access
B
B
holes
B. Use for flat
C
wall mounting
C. Corner
mounting - use all
4 holes.
C
B
B
C
Seal the wiring
and other holes
applied to the
PIR case.
A
GENIUS PLUS FEATURES
• Double Quad Linear Imaging
Technology for sharp analysis
of body dimensions and
differentiation from
background and animals.
• Immunity to animals up to 5kg
(11 lbs).
• High RF and EM Immunity.
• Environmental immunity.
• 15m (49.2 ft) Detection Range
with Wide Angle Lens
• Temperature compensation.
• Compact Design for
Residential Installation
• Variable pulse width
adjustment.
• Sensitivity adjustment.
• Height installation calibrations
free from 1.8m (5.9 ft) to 2.7m
(8.9 ft).
MOUNTING THE DETECTOR
A variety of mounting positions is possible with
the standard GENIUS PLUS housing.
1. Open the front cover by pushing with
screwdriver the holding pin at the
middle of its lower surface and lifting
upwards.
2. Snap out the detector PCB.
3. The Genius Plus housing can be
mounted in a variety of ways. The
circular indentations in the housing
indicate mounting holes to be punched
out in accordance with the desired
mounting position:
4. For surface mounting punch out the 4
indentations marked “ B ” (see Fig. 2).
5. For Corner mounting gives 45° angles
on either the right or the left side. Punch
out the indentations marked “ C ” (see
Fig. 2)
Terminal 1 - Marked “ - ” (-12V)
Connect to –12V e control panel.
Terminal 2 - Marked “ + ” (+12V)
Connect to a positive Voltage output of 8.2 -16Vdc
source (usually from the alarm control unit)
Terminals 3 & 4 - Marked “ TAMPER ”
If a Tamper function is required connect these
terminals to a 24-hour normally closed protective
zone in the control unit. If the front cover of the
detector is opened, an immediate alarm signal will be
sent to the control unit.
Terminals 5 & 6 - Marked “ RELAY ”
These are the detector relay contacts output.
Connect to a normally closed zone in the control
panel.
TERMINAL BLOCK CONNECTIONS
FIG. 3 -
12VDC TAMP RELAY
NC
- +
1 2 3 4 5 6
NC
10 11 12
FIG. 4 – GENIUS PLUS PCB LAYOUT
LED
LED
JUMPER
PYROSENSORS
TAMPER
Wire Terminal
13 14 15
FIG. 5 – WIDE ANGLE LENS PATTERN
0m
0ft
2.4m
7.9ft
0m 5m 10m 15m
0ft 16.4ft 32.8ft 49.2ft
16 17 18
TECHNICAL SPECIFICATIONS
Power input 8.2 - 16VDC
Current consumption
Standby 13mA at 12VDC
Active 8.5mA at 12VDC
Detection speed 0.15 to 1.8m/sec (0.5 to 6 ft./sec)
Alarm output N.C 50mA at 24VDC
27ohm in line resistor
Tamper switch N.C 50mA at 24VDC
10ohm in line resistor
Operating temperature -20°C to 50°C (-4°F to 122°F)
Operating humidity Up to 95% (non-condensing)
Storage temperature -40°C to 80°C (-40°F to 176°F)
Detection method 2 matching dual element
with double optic system
RFI protection >30V/m at 10 to 1000MHz
EMI immunity 50,000Volt electrical interference
due to power surges or lighting
LED Indicator LED is blinking 8 times during
warm up period and self-testing 12 Sec.
LED is ON during alarm.
Dimensions 88 x 48 x 33mm
Weight 53 gr. (1.9 oz)
(3.46” x 1.9” x 1.3”)
Genius manual English
15m
49.2ft
PULSE
JAMPER
JUMPER SWITCHS SETTING
Pulse Jumper - Provides control for normal or high
risk operating environments.
This setting is for a stable
environment without air drafts.
The GENIUS PLUS will automatically select
the appropriate pulse count level according to
the strength of the incoming signals.
This setting is for operation in a harsh
environment with air drafts or with a small
animal less than 25cm (0.8ft) in height and less
than 5kg (11.02lbs).
In AUTO mode, the GENIUS PLUS will increase
its sampling rate and take more factors into
account.
LED Jumper – LED control selection
LED ENABLE - The LED will light when
the GENIUS PLUS is in alarm condition.
WIDE ANGLE LENS PATTERN
COVERAGE WIDE
ANGLE
90°
15m x 22m
49.2ft x 72.2ft
___________________________________
TOTAL
DETECTION 42
ZONES
IMPORTANT:
In an environment with a small animal:
1. The GENIUS PLUS has to be mounted at
2.4m (7ft.) or higher (max 2.7m or 7.9ft.)
above floor level.
2. Install the GENIUS PLUS vertically (not
tilted forward).
3. Away from furniture 2.4m (7.9ft.) or
objects, on which a small animal may
jump.
4. Not facing a staircase, ladder or similar
object that can be part of the monitored
environment (the vertical motion of the
animal may be interpreted by the detector
as an actual intruder).
5. Flip jumper switch “PULSE to the “AUTO”
(down) position for a harsh environment.
WARRANTY
Av-Gad Systems Ltd. and its subsidiaries and affiliates
(“Seller”) warrant its products to be free from defects in
materials and workmanship under normal use for 12
months from the date of sale. Because Seller does not
install or connect the product and because the product may
be used in conjunction with products not manufactured by
Seller, Seller cannot guarantee the performance of the
security system which uses this product. Seller’s
obligation and liability under this warranty is expressly
limited to repairing or replacing, at Seller’s option, within
a reasonable time after the date of delivery, any product
not meeting the specifications.
Seller makes no other warranty, expressed or implied,
and makes no warranty of merchantability or of fitness
for any particular purpose.
In no case shall seller be liable for any consequential or
incidental damages for breach of this or any other
warranty, expressed or implied, or upon any other basis
of liability whatsoever.
Seller’s obligation under this warranty shall not include
any transportation charges or costs of installation or any
liability for direct, indirect or consequential damages or
delay.
Seller does not represent that its products may not be
compromised or circumvented; that the product will
prevent any personal injury or property loss by burglary,
robbery, fire or otherwise; or that the product will in all
cases provide adequate warning or protection.
LED DISABLE - The LED is disabled.
WIRE SIZE REQUIREMENTS
Use #22 AWG (0.5 mm) or wires with a larger
diameter. Use the following table to determine
required wire gauge (diameter) and length of wire
between the detector and the control panel.
Wire Length m 200 300 400 800
Wire Diameter mm .5 .75 1.0 1.5
Wire Length ft. 800 1200 2000 3400
Wire Gauge # 22 20 18 16
The Genius Plus provides PET immunity
up to 5Kg (11.02 lbs).
TEST PROCEDURES
Wait one minute warm-up time after applying 12
VDC power. Conduct testing with the protected area
cleared of all people.
Walk test
• Remove front cover.
The pulse jumper must be in position 1.
The LED must be enabled.
• Replace the front cover.
• Start walking slowly across the detection
zone.
• Observe that the detector’s LED lights
whenever motion is detected.
• Allow 5 sec. between each test for the
detector to stabilize.
• After the walk test is completed, the LED
may be disabled.
NOTE:
Walk tests should be conducted, at least once a
week, to confirm proper operation and coverage of
the detector.
Buyer understands that a properly installed and maintained
alarm may only reduce the risk of burglary, robbery or fire
without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no personal injury
or property loss as a result.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR
ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER
LOSS BASED ON A CLAIM THAT THE PRODUCT FAILS TO
GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE,
WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR
DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OF ORIGIN, SELLER’S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED
THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE
THE COMPLETE AND EXCLUSIVE REMEDY AGAINST
SELLER.
No employee or representative of Seller is authorized to
change this warranty in any way or grant any other
warranty.
Warning: Test this product at least once a week
Item 4775
UK. Edition 2, March 2005
These instructions supersede all previous issues in circulation p rior
to April 2003.
Loading...