English language
L8400
Leaflet No. 463314 rev 01
Read through instructions before commencing installation.
If you have any questions about this product or issues with installation
STOP
CUSTOMER SERVICES HELP LINE NUMBER:
contact the customer services helpline before returning this product to
the store. See for instruction video.
01952 670009
0870 0609777
AVF Group Ltd. Road 30. Hortonwood Ind Est, Telford, Shropshire, TF1 7YE, England
ALL
www.avfgroup.com/unimax
121lbs
55kg
80"
203cm
1
Boxed Parts
You will not need all these parts, so expect there to be some left over depending upon the
specification of your TV.
- x1
A
LH Wall
Bracket
TV Fixings: Parts go on the back of the TV
(specification of your TV will determine
which ones you require - see section 11).
E1
Spacer
- x4
F1
M4 Adaptor
- x12
Spacer (Red)
- x4
F2
M5 Adaptor
E2
- x4
- x4
F3
M6 Adaptor
- x1
B
RH Wall
Bracket
Wall Fixings: Parts to attach to the wall
(type of wall will determine which fixings
you require).
- x4 - x4 - x8
H I J
Wall Fixing Long Wall
No.14 x 105mm
No.12 x 25mm
- x2
C
Hanger
Plug
D
Stand-off
Lock Nut
- x2
- x4
G1
M4 16mm
- x4
G4
M5 16mm
- x4
G7
M6 16mm
- x4
G10
- x4
G2
M4 25mm
- x4
G5
M5 25mm
- x4
G8
M6 25mm
- x4
G11
- x4
G3
M4 45mm
- x4
G6
M5 45mm
- x4
G9
M6 45mm
- x4
G12
- x4 - x2 - x4
- x4 - x2 - x4
K L M
K L M
Long Screw Metal Stud
Long Screw Metal Stud
Screw
Screw
No.14 x 70mm
N O P
Screw Screw Screw Plug
Included Tools
No.8 x 38mm
- x4 - x2 - x2
- x1
R
18mm Wood
Drill
S
3mm Hex
- x1
Key
Wall Plug
Wall Plug
Q
Wall Plug
T
Level
U1
- x2
- x1
- x1
M8 16mm
M8 25mm
M8 45mm
Template
U2
- x1
2
Tools Required
3
Choose from the TV Fixings selection.
You need to determine which length
and diameter of screws fits your TV.
To determine the correct screw diameter,
try screwing (G2), (G5), (G8) & (G11) into
one of the fixing holes on the back of the
screen until you find the one that fits.
4
Once you have established which screws you need for your TV, you can attach the Hangers (C)
and Stand-offs (D) to the back of your TV.
Typical recommended example shown is for fixings with the TV spaced 20mm from the wall.
The TV Mount can position your TV between 12mm and 40mm from the wall. For alternative
configurations see section 11.
You might need to use spacers to increase the clearance of your TV from the wall in order to avoid
cables coming out of your TV and improve access and ventilation to the back of your TV (spacers
(E1) allow you to have a gap of 20mm or 40mm, see section 11).
Determine Correct TV Screw Size
G2, 5 ,8, 11
Fit Screen Hangers To TV
In certain circumstances it may be necessary to use red spacer (E2) as either a replacement or
addition to spacer (E1), for more information please see section 11.
If your TV fixing centres don’t fit, STOP installation and contact the customer services helpline.
Top Fixings
G2, 5 ,8, 11
F1, 2, 3
If Required
Bottom Fixings
G2, 5 ,8, 11
F1, 2, 3
*
C
E1
TV must be parallel
to wall. Use spacers /
stand-offs as shown.
If using screw use Adapter (F1)(G2)
*
If using screw (G5) use Adapter (F2)
If using screw (G8) use Adapter (F3)
If using screw (G11) No Adapter required
D
E1
*
5
The horizontal part of the positioning template is used to mark out
where you need to drill the mounting holes on your wall. The vertical
part is just a guide to allow you to see how high up the wall your TV
will be to help you find the perfect position for viewing your screen.
Thread template (U2) through template (U1) as shown.
Assemble Positioning Template
U1
U2
6
Lay the template on the back of the TV and follow the instructions below.
Determine Bracket Hole Centres
Line up the template with
The centre line of the template
represents the centre of your TV.
Line up with top of
Line up with top of
the screen.
the screen.
the centre of the screen.
Mark off the fixing centres.
Tear off the template flush with the
bottom of your TV so that when
the template is on the wall you can
see exactly where your TV will be
vertically (distance from the floor
and ceiling).
If your screen fixings do not line
up with any holes on the template
then ensure template is on the
centre of the screen, and punch
holes to suit your screen fixings
centres with a pencil or sharp
object.
7
Use your template to mark two points on the wall that correspond with the top fixing centres of
your TV.
Marking Wall For Drill Points
Represents the top
of your TV
centre of your TV.
Represents the base
of your TV
Pencil Mark
.
Represents the
.
T
Next, use the Wall Brackets (A) and (B) as a template
and position it over one of the PENCIL MARKS you
have made, so that the mark is in the middle of the
CENTRAL HOLE of the Wall Bracket (A). Ensure
the bracket is level and mark the three DRILL
POINTS with a pencil. Repeat for both brackets.
T
B
Central Hole
Drill points
A
Drill points
8
Determine the wall type that you have (i.e. Brick/Stud/Plasterboard/Sheetrock).
Ensure the drilling area is free from mains services (Gas/Electric/Water).
Drill six 3mm diameter pilot holes to verify the wall type and select the appropriate fixings (See
Section 9).
Planning & Preparation
9
Use the correct fixings for your wall type. Mixing fixing types may be required for installations that
span different wall types. DO NOT OVER TIGHTEN SCREWS.
Install Wall Fixings
SRQPONMLKJIHBA
75mm (3")
Remove
dust from
holes
Solid WallDot & DabPlasterboard
40mm (19/16")
108mm
(41/4")
40mm Max
(19/16")
*
Remove
dust from holes
Ø18mm
(3/4")
R
Ø10mm
(25/64")
Ø5.5mm
(7/32")
Ø10mm
(25/64")
M
Q
I
P
Self drilling
If gap is above 40mm use
Plasterboard / Sheetrock fixing method
*
H S
(19/16")
Turn until secure
Do not over
tighten
A+B
A+B
Lubricate screw
thread with soap
A+B
Lubricate screw
thread with soap
A+B
N
O
K
O
J
P
/ Sheetrock
Ø3mm
(1/8")
Self drilling
40mm (19/16") Min gap
Use Plasterboard /
Sheetrock fixings
Lubricate screw
thread with soap
A+B
O
Use Plasterboard /
Sheetrock fixings
P
Wood StudMetal Stud
Only one fixing will be in the wood stud. The other fixings will be in plasterboard / sheetrock (see above).
Ø3.5mm
(9/64")
Self drilling
Use Plasterboard /
Sheetrock fixings
Hand tighten
only
P
Self drilling
Only one fixing will be in the metal stud. The other fixings will be in plasterboard / sheetrock (see above).
O
A+B
O
N
Use Plasterboard /
Sheetrock fixings
L
10
Hanging The TV
Guide
Recess
Present the yellow Hangers
(on the back of the TV) to the
guide recess on the Wall
Brackets. Slide down and across
into place. Ensure both yellow
Hangers are fully engaged.
If cables from the TV prevent
the TV resting against the wall
then an alternative hanger
configuration will be required
(See Section 11).
TV must be parallel to wall. Use
spacers / stand-offs as shown.
I II
III IV
If required you can adjust
the level of your TV by moving
your TV from side to side.
Removing the TV
This is a two person job. To remove the TV reverse the movements as shown above.
11
Alternative Hanger Configurations
Wall Space
Alternative Wall spacings of 12mm, 20mm & 40mm can
be achieved using the spacer / screw combinations
listed in this section.
20mm Wall Space
12mm Wall Space 40mm Wall Space
(as shown in section 4)
Top FixingsTop Fixings Top Fixings
G1, 4, 7, 10
F1, 2, 3
*
C
G1, 4, 7, 10
F1, 2, 3
*
D
G2, 5, 8, 11
F1, 2, 3
*
C
E1
G3, 6, 9, 12
F1, 2, 3
*
C
E1
E1
E1
Bottom FixingsBottom Fixings
G2, 5, 8, 11
F1, 2, 3
*
D
E1
Bottom Fixings
G3, 6, 9, 12
F1, 2, 3
*
D
E1
E1
E1
TV must be parallel to wall. Use spacers / stand-offs as shown.
If using screw (G1),(G2) or (G3) use Adapter (F1)
If using screw (G4),(G5) or (G6) use Adapter (F2)
If using screw (G7),(G8) or (G9) use Adapter (F3)
*
If using screw (G10),(G11) or (G12) No Adapter required
When is it necessary to use red spacers?
E1 E2
Problem
Not enough
screw engagement
It is recommended that when fitting Hangers ( ) and
Stand-offs ( ) to your TV you have at least 5-10mm of
screw engagement. In certain circumstances you may
need to use red spacers ( ) as either a replacement, or
together with spacers ( ) to achieve this. Whenever
TV TV
you use red spacers (E2) you must use all 4 provided.
D
E2
E1
C
- x4
E2
Solution
Red spacer (E2) has
replaced spacer (E1)
Loading...