Page 1
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
Control Your Video
CABLES & ACCESSORIES
H.264 IP CAPTURE TO HDMI ENCODER/
DECODER WITH TELNET AND AUDIO SUPPORT
© 2017 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Model #: HDM-XTRM-IP-SET
Page 2
Product Application & Market Sectors
Corporate House Of Worship
Military Residential
Education Industrial
Medical Aviation
www.avenview.com
Page 3
TABLE OF CONTENTS
1. GETTING STARTED ..........................................................................................................................1
1.1
IMPORTANT SAFE GUARDS..............................................................................................................1
1.2 SAFETY INSTRUCTIONS
1.3
REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISIION (FCC) ........................... 2
2. INTRODUCTION ..............................................................................................................................3
2.2 BEFORE INSTALLATION ...................................................................................................................4
2.3 APPLICATION DIAGRAM ..................................................................................................................5
2.4 PANEl DESCRIPTION .......................................................................................................................6
2.4.1 FRONT PANEL (ENCODER, TRANSMITTER)
2.4.2 REAR PANEL (ENCODER, TRANSMITTER) .........................................................................6
2.5.1 FRONT PANEL (DECODER, RECEIVER)
2.5.2 REAR PANEL (DECODER, RECEIVER) ..................................................................................7
3. INSTALLATION (HDM-XTRM-IP) .....................................................................................................8
3.1 NETWORK SWITCH CONFIGURATION............................................................................................8
3.2 DECODING USING PC SOFTWARE...................................................................................................9
3.3 CHANGING STREAM TYPE AND MODE ..........................................................................................9
................................................................................................................1
.....................................................................................................................4 2.1 PACKAGE CONTENTS
......................................................................6
.............................................................................7
4. SETTING A STATIC IP ON COMPUTER ............................................................................................10
5.
CONNECTING TO HDM-XTRM-IP ..................................................................................................12
6. DECODING WITH HARDWARE DECODER.....................................................................................17
7.
SPECIFICATIONS ...............................................................................................................................18
Page 4
SECTION 1: GETTING STARTED
1.1
IMPORTANT SAFE GUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
• Any product, on which the serial number has been defaced, modified or removed.
• Damage, deterioration or malfunction resulting from:
• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
• Repair or attempted repair by anyone not authorized by us.
• Any damage of the product due to shipment.
• Removal or installation of the product.
• External causes to the product, such as electric power fluctuation or failure.
• u se of supplies or parts not meeting our specifications.
• Normal wear and tear.
• Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The Avenview HDM-XTRM-IP H.264 IP stream Encoder/Decoder has been tested for conformance to safety regulations and
requirements, and has been certified for international use. However, like all electronic equipments, the HDM-XTRM-IP should be
used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to
the unit.
Do not dismantle the housing or modify the module.
!
Dismantling the housing or modifying the module may result in electrical shock or burn.
!
Refer all servicing to qualified service personnel.
!
Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
!
or other hazards
keep the module away from liquids.
!
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
!
to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
!
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
!
1
Page 5
1.3
This equipment has been tested and found to comply with part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
Warning symbols Description
ONlY USE THE PROVIDED POWER CABLE OR POWER
ADAPTER SUPPLIED. DO NOT TAMPER WITH THE
ELECTRICAl PARTS. THIS MAY RESULT IN El ECTRICAL
SHOC
K OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WIll
VOID THE WARRANTY AND CONTINUED USE OF
THE PRODUCT
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON
A SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.
2
Page 6
2.
The Avenview HDM-XTRM-IP-SET, HDMI H.264 IP stream Encoder/Decoder delivers end-to-end streaming media over IP
networks. The HDM-XTRM-IP-SET is a total architecture based on the TCP/IP protocol family. This device is engineered to
deliver A/V signal over WAN or LAN, video extension -with the help of matching network equipmentsseveral thousands of km's
FEATURES:
• H.264 video decoder;
• Transmits audio and video from ethernet port to HDMI;
• Streams media through LAN or WAN;
• Input Resolutions: From 640x480@60Hz to 1080p@24/25/30/50/60Hz;
• Can be used using the Encoder only with Avenview PC decoding software over IP;
• Receive TS data with unicast or multicast method;
• Supports RTSP protocol;
• Output Resolution: From 640x480@60Hz to 1080p@24/25/30/50/60Hz;
• Supports audio format including LPCM or AAC standard;
• Displays can be controlled using RS-232 or CEC;
• Telnet CLI and Web UI supported;
• Supports static IP, DHCP and AutoIP;
• Video Bitrate: 2m~30Mbps;
• AAC Audio Bitrate: 32~240Kbps;
• LPCM Audio Bitrate: 1.6Mbps;
• Supports video timing up to 1920x1080@60Hz and 1920x1200@60Hz;
• Low Latency Mode: 120ms end-to-end latency.
INTRODUCTION
can be achieved over
- NOTE: The QUALITY and TRANSMISSION of the video signals depends on the characteristics and quality of the UTP cables
and Network Infrastructure . We recommend any Network Switches with 1GB POE IGMP v2.0 support . Tested and configured
on the below models
www.avenview.com
3
Page 7
PACKAGE CONTENTS
2.1
Before you start the installation of the HDMI Extender, please check the package contents.
HDM-XTRM-IP
1
2
Power Adapter (+12V DC 1A)
+ International Adapters
1 x Right and Left Ear Rack Sets
3
4
User Guide
X1
X1
X2
X 1
2.2 BEFORE INSTALLATION
• put the product in a level and stable location. If the product falls, it may cause damage or malfunction to components
within the casing.
• Do not place the product in temperatures under 0˚C or over 50˚C. High humidity may also cause the unit to malfunction.
• u se the DC power adapter with correct specifications supplied with the unit. If the improper power supply is used, this
may result in malfunction of the unit and may cause fire.
•
Do not twist or pull by force the ends of the UTP cable. It will cause malfunction.
www.avenview.com
4
Page 8
2.3 APPLICATION DIAGRAM
APPLICATION DIAGRAM 1
APPLICATION DIAGRAM 2
IP CAMERA
WAN
LAN
Input/Output CAT 5e / CAT 6
HDM-C6MWIP-R
HDM-C6MWIP-R
HDM-C6MWIP-R
HDM-C6MWIP-R
10GB
NETWORK
SWITCH
HDM-C6MWIP-S
HDM-XTRM-IPR
www.avenview.com
5
Page 9
2.4 PANEL DESCRIPTION (ENCODER/TRANSMITTER)
2.4.1 FRONT PANEL
1
2
Power LED: Indicates if the unit is powered OFF or ON by a RED LED
1.
Status LED: Steady Blue Light ON indicates unit is communicating properly. LED blinking waiting on Source
2.
2.4.2 REAR PANEL
1
2
POWER JACK: 12V DC Power Jack.
1.
RESET: Reset device to factory default.
2.
3. HDMI IN: Connect to HDMI/DVI Source.
4. LAN: Used for send video/audio streams to Decoder or over the network.
3
4
www.avenview.com
6
Page 10
2.5 PANEL DESCRIPTION (DECODER/RECEIVER)
2.5.1 FRONT PANEL
1 2
Power LED: Indicates if the unit is powered OFF or ON by a RED LED
1.
Status LED: Steady Blue Light ON indicates unit is communicating properly. LED blinking waiting on Source
2.
2.5.2 REAR PANEL
1
POWER JACK: 12V DC Power Jack.
1.
LAN: Used to receive video/audio streams to from Encoder.
2.
3. HDMI OUT: Connect to display/TV.
4. AUDIO OUT: Connects to an audio output device such as an amplifier for audio de-embedding.
RS-232: RS-232 Data pass-through port for receiving /sending commands to RS 232 device.
5.
2
3
4
5
www.avenview.com
7
Page 11
3. INSTALLATION
To setup Avenview HDM-XTRM-SETplease follow the following steps:
1.
Turn off all devices including monitors / TV.
2.
Connect an HDMI source (such as a Blu-Ray Disc player or PC) to the Encoder HDM-XTRM-IPS.
3.
Connect CAT5/6 from Encoder to exisitng network or the network switch.
4.
Download the compatible video player software on PC.
5.
Power on all devices and follow the instructions on how to start IP streaming.
NOTE: For network setup please see the Network switch configuration guide and Network Connection guide to
acheive best results.
(HDM-XTRM-SET)
(Player that support live netwrok IP streaming)
3.1 NETWORK SWITCH CONFIGURATION
Power on the switch and change configurations following the steps below*:
1. If your switch is supplied with our products, it has been configured correctly and passed our tests. Therefore, it can be
used without any configuration.
2. If we do not provide any switch with our products or you want to use other switches, we would recommend that you
use a switch tested by us and configure it by following our instructions.
3. If you use a switch which is not tested by us, configure it by referring to the following requirements.
- Disable green or energy-saving feature
- Enable Multicast forwarding or filtering
- Enable IGMP Snooping
- Assign a valid IP address to the IGMP Querier
- Enable IGMP Querier
- Enable IGMP fast leave
- Disable dynamic multicast router port
- Disable forwarding unknown multicast
All related settings above must be configured in global configuration and VLAN configuration. For more detailed information on
configuring the network switch please check netwrok guide at:
http://www.avenview.com/images/manuals/Avenview%20HDM-C6MXIP-SET%20NetworK_Switch%20%20Cisco%20rv01.pdf
* Menu configuration might differ depending on the netwrok switch used.
www.avenview.com
8
Page 12
3.2 DECODING USING PC SOFTWARE
1. Power on source device, encoder and PC.
2. Configure your PC's network settings with IP address 192.168.1.11 and subnet mask 255.255.0.0, leaving gateway and
DNS blank.
3. Launch Avenview media player.
4. In the menu bar, select Media -> Open Network Stream, input rtp://@226.1.1.1:12345, then click Play.
5. The software will start playing the video content of the source device.
6. Configure the encoder to alter the encapsulation and transmission mode of the media stream, and control the Avenview
media player to play the media stream with the corresponding parameter.
3.3 CHANGING STREAM TYPE AND MODE
The default stream type is TS over UDP, to use other stream type and mode follow below steps:
1. Launch a web browser in your PC and type in 192.168.10.254 in the address bar;
2. In the displayed login dialog box, enter the default password admin;
3. In the Functions page, expand the Stream section;
4. For the item Transport type, set its value to tsoverudp, then click Apply;
5. For the item Dest IP address, set its value to 192.168.1.11, namely, the IP address of your PC, then click Apply;
6. Launch Avenview media player, in the menu bar select Media -> Open Network Stream, input udp://@:12345, then click Play.
Notice:
The URL assigned to Avenview Media Player depends on the configurations, stream type and Destination IP address, please
refer to the following details:
Transport type Dest IP address URL for VLC
tsoverrtp 226.1.1.1 rtp://@226.1.1.1:12345
tsoverudp 226.1.1.1 udp://@226.1.1.1:12345
tsoverrtp
tsoverudp udp://@:12345
192.168.1.11
(PC’s IP address)
rtp://@:12345
www.avenview.com
9
Page 13
4. Setting a Static IP on Computer
Before logging into the HDM-XTRM-IP devices, please ensure all devices are in the same network segment. To verify
and properly control the devices, please set a static IP on your computer. See the instructions below for more details.
The Encoder and Decoder units are pre-configured with AutoIP. Upon connecting the units to a stand alone network
switch (without router attached), the units will be on IP address range at 192.168.1.11 and subnet mask 255.255.0.0.
Set your computer's IP address as 192.168.X.X and subnet mask as 255.255.0.0.
A Windows 7 PC/Laptop is used as an example to configure a static IP address.
Click Start.
1.
Choose Control Panel > Network and Internet > Network and Sharing Center > Change
2.
Adapter Settings, right click Local Area Connection, and then choose Properties.
www.avenview.com
10
Page 14
Select Internet Protocol Version 4 (TCP/IPv4) and click Properties
3.
Select Use the following IP address. After configuring the setti
4.
click OK.
IP address: 192.168.1.11
Subnet mask: 255.255.0.0
OK.
Click
5.
ngs in the following example,
www.avenview.com
11
Page 15
5. CONNECTING TO HDM-XTRM-IP
1. Log in into HDM-XTRM-IP by entering the default IP address: 192.168.10.254 into a web browser
2. Enter default Password: 12345
www.avenview.com
12
Page 16
3.
"Video" submenu allows:
- Change HDCP
- Change Bitrate
- Change Output Resolution
4. Main page interface includes "Functions" and "System" tabs.
www.avenview.com
13
Page 17
5. "Audio" settings allow to choose the encoder Audio "Type" and "Bitrate"
6.
"Thiele/Small parameters"
Allows changing the specified low frequency performance of a loudspeaker driver
www.avenview.com
14
Page 18
7. "Stream" settings allows:
- Enable or Disable Streaming
- Change "Transport Type"
- Change "IP Address"
- Change "Port"
8. "Transport Type" can be switched between:
User datagram Protocol (UDP) and Real-time transport protocol (RTP)
www.avenview.com
15
Page 19
9. "System" allows:
- Change device name
- Change IP Mode, Subnet mask, Gateway
- Change Password
- Change Background Picture
10. Cont'd "System" allows:
- Check Device Firmware Information
- Command control and Reboot
- Event Log
www.avenview.com
16
Page 20
6. DECODING WITH HARDWARE DECODER
Hardware decoder is optional and provides an alternative way to stream over IP without using a PC or video streaming softwares, please refer
to HDM-XTRM-IPR guide for more information.
www.avenview.com
17
Page 21
www.avenview.com
Page
7. SPECIFICATIONS
Item
Units
Unit Description HDMI Transmitter/Encoder
Input Video Port
Input Video Type
Input Resolution
HDMI:
640 x480@60Hz,
480i@60Hz 480p@60Hz，
576i@50Hz,576P@50Hz,
800 x600@60Hz，
1024 x768@60Hz,
720p@50Hz,720p@60Hz,
1280 x 800@60Hz,1280 x1024@60Hz,
1360 x 768@60Hz,1366 x 768@60Hz,
1400 x 1050@60Hz,1440 x900@60Hz,
1680 x1050@60Hz,
1080i@50Hz,1080i @60Hz，
1080p@24Hz,1080p@25Hz,1080p@30Hz,
1080p@50Hz,1080p@60Hz,
1920 x 1200@60Hz
DV
I:
640 x480@60Hz,
480i@60Hz, 480p@60Hz，
576i@50Hz,576P@50Hz,
800 x 600@60Hz,
1024 x768@60Hz,
720p@50Hz,720p@60Hz,
1280 x 800@60Hz,1280 x1024@60Hz,
1360 x 768@60Hz,1366 x 768@60Hz,
1400 x 1050@60Hz,1440 x 900@60Hz,
1680 x 1050@60Hz,
1080i@50Hz,1080i @60Hz，
1080p@24Hz，1080p@25Hz,1080p@30Hz,
1080p@50Hz, 1080p@60Hz,
1920 x 1200@60Hz
VGA:
640 x 480@60Hz,
800 x 600@60Hz
1024 x 768@60Hz,
1280 x1024@60Hz
1280 x720@60Hz，
1280 x 768@60Hz，
1280 x 800@60Hz，
1360 x 768@60Hz,
1440 x 900@60Hz
Description
HDM-XTRM-IP-S
1 x HDMI IN
HDMI 1.4, DVI 1.0
1366 x 768@60Hz,
18
Page 22
1400 x 1050@60Hz
1680 x1050@60Hz，
1920 x1080@60Hz,
1920 x 1200@60Hz
YPbPr:
720 x 480i@60Hz,720 x 480p@60Hz，
720 x 576i@50Hz,720 x 576P@50Hz，
1280 x720p@50Hz,1280x720p@60Hz
1920 x1080i@50Hz,1920 x 1080i@60Hz
CVBS:
480i@60Hz,576i@50Hz
Input Video Signal
Encoding Data Rate
Output Video Ports
Output Video Type
Output Video Resolutions
Video Impedence
put DDC Signal
In
En
d-to-End Time Latency
put Audio Ports
In
In
put Audio Format
Output Audio Format
Control Method
Power Supply
Power Consumption
Shipping Dimensions
Product Dimensions
Weight
ESD Protection
Environmental
OPERATING TEMPERATURE
STORAGE TEMPERATURE
RELATIVE HUMIDITY
0.5~1.2 V p-p
Up to 30 Mbps, configurable
1 x CAT5/6
H.264/MPEG-4 AVC
Large IP stream:
480p@60Hz~1920 x 1200@60Hz
Small IP stream: 352x288@5Hz
100 Ω
5 V p-p (TTL)
About 60ms-90ms (Low latency mode)
About 250ms-300ms (High quality mode)
HDMI
Audio embedded in streaming media input
Stereo
Rear panel CAT5/6 port,
PC configurator and RS-232
12 V 1 A DC
6W (Max.)
12.2'' L x 3.0'' H x 7.1" D
9.3'' L x 1.0'' H x 3.7" D
3 lbs
Human body model:
-±8kV (air-gap discharge)
-±4kV (contact discharge)
32˚ ~ 104˚F (0˚ to 40˚C)
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
20~90% RH (no condensation)
www.avenview.com
Page
19
Page 23
1. All HDMI over CATx transmission distances are measured using Belden CAT6A (625MHz),
4-Pair,UTP-Unshielded, Riser-CMR, Premise Horizontal Cable, 23 AWG Solid Bare Copper
Conductors, Polyolefin Insulation, Patented Double-H spline, Ripcord, PVC Jacket using
Quantum 980 signal HDMI Video Generator Module with Video Pattern Testing and shielded
ends.
2. The transmission length is largely affected by the type of category cables, also the type of HDMI
sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in the
form of 300m or 1000ft bulk cable) can transmit a lot longer signals than stranded UTP cables
(usually in the form of patch cords). Shielded STP connectors are better suit than unshielded
UTP connectors. A solid UTP CAT6A cable shows longer transmission length than solid UTP
CAT5E/6E cable.
3. EIA/TIA-568-B termination (T568B) for category cables is recommended.
4. To reduce the interference among the unshielded twisted pairs of wires in category cable, you
can use shielded STP cables with shielded connector to improve EMI problems, which occurs in
poor wiring environments with unplanned cable runs situated away from EMI interference.
5. Because the quality of the category cables has the major effects in how long transmission distance
will be made and how good is the received signal on the display, the actual transmission length
is subject to high quality category cables. For resolution greater than 1080i or 1280x1024, a
solid CAT6E 250MHz cable is the only viable choice.
PERFORMANCE GUIDE FOR HDMI OVER CATEGORY CABLE TRANSMISSION
PERFORMANCE RATING TYPE OF CATEGORY CABLE
WIRING SHIELDING CAT5 CAT5E CAT6
u NSHIEl DED (u Tp) ✶✶✶ ✶✶✶✶ ✶✶✶✶
SOLID
SHIEl DED (STp) ✶✶✶ ✶✶✶✶ ✶✶✶✶✶
u NSHIEl DED (u Tp) ✶ ✶✶ ✶✶
STRANDED
SHIEl DED (STp) ✶ ✶ ✶✶
TERMINATION PLEASE USE EIA/TIA-568-B TERMINATION (T568B) AT ANY TIME
www.avenview.com
20
Page 24
Avenview Warranty Certificate
AVENVIEW CORP. (“Ave
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact support@avenview.com.
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
support@avenview.com.
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of A venview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATI ON; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
nview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
NOT COVERED BY THIS WARRANTY
275 Woodward A
venue, Kenmore, NY 14217
1.866.508.0269
www.avenview.com
Page 25
Control Your Video
TECHNICAL SUPPORT
Avenview Canada
151 Esna Park Drive, Unit 11-12
Markham, ON L3R 3B1
Phone: +1 905 907 0525
Email: info@avenview.com
Sales: sales@avenview.com
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.
Phone: +1 716 218 4100 x223
Avenview USA
1100 Military Road
Kenmore, NY 14217
Fax: +1 866 387 8764
Email: info@avenview.com
Avenview Europe
Email: info@avenview.eu
Avenview Asia
Email: wenxi@avenview.com.hk
Sales: sales@avenview.com.hk
Loading...