Avenview FO-HDM-IP4K-SET User Manual

VIDEO WALLS VIDEO PROCESSORS

VIDEO MATRIX SWITCHES

EXTENDERS SPLITTERS WIRELESS

Control Your Video

CABLES & ACCESSORIES

HDMI Extender up to 20KM

over Fiber Optic with IR Support

© 2016 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.

Model #: FO-HDM-IP4K-SET

Product Application & Market Sectors

Corporate House Of Worship

Military Residential

Education Industrial

Medical Aviation

www.avenview.com

TABLE OF CONTENTS

1. IMPORTANT SAFEGUARDS ..............................................................................................................1

1.1 SAFETY INSTRUCTIONS ..................................................................................................................1

1.2 REGULATOR

2. INTRODUCTION .............................................................................................................................. 3

2.1 PACKAGE CONTENTS .....................................................................................................................4

2.2 BEFORE INSTALLATION ...................................................................................................................4

2.3 APPLICATION DIAGRAM .............................................. ....................................................................5

2.4 DEVICE DESCRIPTION & LAYOUT ..................................................................................................7

2.4.1 Front Panel & Rear Panel (Transmitter, FO-HDM-IP4K-S) .......................................................7

2.4.2 Front Panel & Rear Panel (Receiver, FO-HDM-IP4K-R) ............................................................8

2.5 IR CONTROL DESCRIPTION, FO-HDM-IP4K-SET) .........................................................................9

3.

INSTALLATION ................................................................................................................................10

4.

GENERAL TROUBLESHOOTING ....................................................................................................10

5.

SPECIFICATIONS ..............................................................................................................................11

5.

PIN AND WIRING STANDARD DEFINITION ...................................................................................12

Y NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 2

www.avenview.com

Page 3

1. IMPORTANT

Please read all of these instructions carefully before you use the device. Save this manual for future reference.

What the warranty does not cover

• Any product, on which the serial number has been defaced, modified or removed.

• Damage, deterioration or malfunction resulting from:

• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.

• Repair or attempted repair by anyone not authorized by us.

• Any damage of the product due to shipment.

• Removal or installation of the product.

• Causes external to the product, such as electric power fluctuation or failure.

• Use of supplies or parts not meeting our specifications.

• Normal wear and tear.

• Any other causes which does not relate to a product defect.

• Removal, installation, and set-up service charges.

SAFEGUARDS

1.1 SAFETY INSTRUCTIONS

The Avenview FO-HDM-IP4K-SET, HDMI Extender has been tested for conformity to safety regulations and requirements, and has
been certified for international use. However, like all electronic equipment’s, the FO-HDM-IP4K-SET should be used with care.
Read the following safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.

Do not dismantle the housing or modify the module.

!

Dismantling the housing or modifying the module may result in electrical shock or burn.

!

Refer all servicing to qualified service personnel.

!

Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage

!

or other hazards

Keep the module away from liquids.

!

Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on

!

to the housing, unplug the module immediately.

Have the module checked by a qualified service engineer before using it again.

!

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

!

www.avenview.com

Page 1

1.2 REGULATOR

This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.

Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.

Warning symbols Description

Y NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)

ONLY USE THE PROVIDED POWER CABLE OR POWER

ADAPTER SUPPLIED. DO NOT TAMPER WITH THE

ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL

SHOCK OR BURN.

DO NOT TAMPER WITH THE UNIT. DOING SO WILL

VOID THE WARRANTY AND CONTINUED USE OF THE

PRODUCT.

THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.

lASER BEAM uSED IN OpTICAl COMMuNICATIONS ARE

INVISIBlE AND CAN SERIOuSly DAMAGE THE EyES.

VIEWING IT DIRECTly DOES NOT CAuSE ANy pAIN TO

THE EyE BuT SERIOuS DAMAGE CAN BE DONE TO THE

RETINA Of THE EyE

www.avenview.com

Page 2

2. INTRODUCTION

FO-HDM-IP4K-SET, HDMI extender set is designed to provide high quality video signal transmission over fiber optic cable or an
existing fiber network. Avenview's FO-HDM-IP4K-SET delivers an amazing pixel to pixel transmission of 4K@30 or 1080p HDMI
signal up to 20 kilometers. With this extender users overcome the length restrictions of standard HDMI cables or UTP Extenders. This
unit can control your IR device from the monitors side with its supplied IR technology built in.
Bonus feature: The FiberTransmitter is also compatible with the HDM-C6IPX-R CAT5/6 Receiver, this simply means user can
migrate from a Fiber network to to copper network by adding the comptible RX device.

FEATURES:

The Sender and Receiver units can extend 20000 meters (20 km) over a Fiber Optic cable point to point;

•

The Sender can be connected to a Fiber network switch to establish an IP address therefore sending 1080p/4K video signals to

•

multiple Receivers connected to the Fiber network switch and the HDMI displays;
Multiple Senders can be connected to a Managed Fiber switch with VLAN/IGMP support therefore sending 1080p/4K video

•

signals to Receivers connected to the network switch to show different sources on multiple displays;*

•

Extends HDMI signal up to 20 km over fiber optic;

•

HDCP compliant;

•

Supported resolutions: 480i@60Hz,480p@60Hz,576i@50Hz,576p@50Hz,720p@50/60Hz,1080i@50/60Hz,1080p@50/60Hz

4K@25/30Hz

•

Supports point to point transmission function which can be expanded to the multi-point to point transmission
function.

•

Number of Senders and Receivers that can be used is dependent on bandwidth of the network switch.

•

Single mode fiber optic transmission.

Support IR pass back for easy control.

•

Built-in electromagnetic interference prevention in environment for long distance transmission.

•

•

Low signal loss, wide frequency band and strong anti-interference features;

Wall-mountable design for convenient installation.

•

High-end aluminum alloy enclosure design.

•

FIBER Network Switch with copper ports

*Requires a managed Gigabit switch with VLAN/IGMP support to have a soultion with multiple sources (Transmitters). Standard

Gigabit switch can only support one transmitter.

- The managed switch must support port based IEEE 802.1Q VLAN, IGMP, and to allow duplicate IP addresses across the VLAN
domains.

- Each VLAN acts as independent HDMI over IP Channel on the network.

COPPER Network Switch with Fiber ports

www.avenview.com

Page 3

2.1 PACKAGE CONTENTS

Before you start the installation of FO-HDM-IP4K, please check the package contents:

HDMI IPX TRANSMITTER X 1

1

HDMI IPX RECEIVER X 1

2

3

IR EXTENDER

4

IR BLASTER

POWER ADAPTER (5VDC2A)

5

6

USER’S MANUAL

X 1

X 1

X 2

X

1

2.2 BEFORE INSTALLATION

• Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.

• Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.

• Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire.

www.avenview.com

Page 4

2.3 APPLICATION DIAGRAM

www.avenview.com

Page 5

2.4 PANEL DESCRIPTION & LAYOUT

This product is SDFNDJHGDVDVHW ZKLFKLQFOXGHV a Transmitter and a Receiver.

2.4.1 Front Panel (Transmitter, FO-HDM-IP4K-S)

1

1. POWER LED: LED lights red when device is

powered on

3. DATA LED: When data is transmitting from the

source the led will continuously flash YELLOW.

5. OPTICAL OUT: Connect SC single mode fiber optic cable.

3 4

2

2. DC 5V: Connect the 5 V DC power supply included.

4. LINK LED: When connected to RX or network switch

the LED will light GREEN.

2.4.2 Rear Panel (Transmitter, FO-HDM-IP4K-S)

1

5

2

5

1. HDMI IN: Connect to HDMI source via HDMI

Cable.

3. RESET: To reset the unit when no link is established.

Important Please do not connect the FO-HDM-IP4K to a POE network switch this will damage and the

units will be come non functional.

2. IR OUT: Plug the IR Blaster cable for IR signal being transmitted.

place IR Blaster within direct site of the device being controlled.

www.avenview.com

Page 7

2.4.4 Front Panel (Receiver, FO-HDM-IP4K-R)

1

1. POWER LED: LED lights red when device is

powered on

3.

DATA LED: When data is transmitting from the

source the led will continuously flash YELLOW.

5

. OPTICAL IN: Connect SC single mode fiber

optic cable.

3 4

2

2. DC 5V: Connect the 5 V DC power supply included.

4. LINK LED: When connected to RX or network switch

the LED will light

2.4.5 Rear Panel (Receiver, FO-HDM-IP4K-R)

1

GREEN.

2

5

3

1. HDMI OUT: Connect to HDMI Display via

HDMI Cable.

3. RESET: To reset the unit when no link is established.

2. IR IN: plug the IR Extender cable for IR signal being received.

place IR Extender within direct line of site with the IR Remote.

www.avenview.com

Page

8

2.5 IR CABLE DESCRIPTION

IR Sockets

-- IR OUT -IR BLASTER: plug in the IR blaster to the HDMC6IPX-S to emit all IR command
signals received from the IR Extender plugged into the Rx (Monitor Side) to control the devices
corresponding to the IR signals. Example: Set Top Box or DVD player (The Source).

-- IR IN - IR EXTENDER: plug in the IR Extender into the (RX) Receiver (Monitor Side) to
receive all IR command signals from the IR remote controls of the corresponding source.
Example: Set Top Box or DVD player (IR Remote Control).

Important IR signals can be affected by very bright fluorescent light and also EMI Interference on the cables

so be aware of wher you place and postion your IR cables. Please follow these instructions for best results.

www.avenview.com

Page

9

3. INSTALLATION

Please ensure all the package contents are all received before proceeding.

To setup Avenview FO-HDM-IP4K-SET follow these steps for connection:

1.

Connect your HDMI source (such as a Blu-ray Disc player) to Transmitter (FO-HDM-IP4K-S).

2.

Connect your HDMI display (such as a LCD TV) to the receiving unit FO-HDM-IP4K-R.

3.

Connect your SC Optic Fiber cord (Single Mode) between the transmitting and receiving units.

4.

Make sure Optic Fiber cord (Single Mode) cable is tightly connected and not loose.

5.

Plug in 5V DC power cord to the power jack of the transmitting unit FO-HDM-IP4K-S

6.

Plug in 5V DC power cord to the power jack of the receiving unit FO-HDM-IP4K-R.

4. GENERAL TROUBLESHOOTING

PROBLEM

NO IMAGE

SCREEN DEFECTS
APPEAR

DATA TRANSMISSION LIGHT
FLASHING SLOW

DATA TRANSMISSION LIGHT
FLASHING FAST/NO IMAGE

NO LIGHT ON DATA
TRANSMISSION

POSSIBLE SOLUTION

•  Check if connection to the source and the display are correct.
Ensure that display device supports 480p, 720p and 1080p/4K resolution

•

Check the HDMI connection if loose or change to a premium HDMI cord

•

•  Check both units and make sure the TX and RX are not Reversed

•  Check the source device is powered ON

Check Graphics card on PC/HD Player. This product supports

•

up to 4K@30p (3840x2160) resolution.

Check Network cable. only use TIA-568B Standard

•

•  Network cable run is out of range

www.avenview.com

Page

10

5. SPECIFICATIONS

ITEM DESCRIPTION

UNITS

UNIT DESCRIPTION

HDMI COMPLIANCE

HDCP COMPLIANCE Yes

FO-HDM-IP4K-S FO-HDM-IP4K-R

HDMI FiberTransmitter HDMI Fiber Receiver

Yes

TMDS BANDWIDTH

SUPPORTED RESOLUTIONS

DDC SIGNAL VOLTAGE

AUDIO SUPPORT Surround Sound (up to 7.1 Ch) or Stereo Digital Audio

IR PASS-THRU

CENTRAL WAVELENGTH 1310nm

LINK LOSS

OUTPUT LIGHT POWER

RECEIVE SENSITIVITY

RETURN LOSS

INPUT

OUTPUT

HDMI CONNECTOR

FIBER OPTIC CONNECTOR

POWER ADAPTER

POWER CONSUMPTION

DIMENSION L X W X H

WEIGHT

Environmental

OPERATING TEMPERATURE

STORAGE TEMPERATURE

RELATIVE HUMIDITY

480i@60Hz,480p@60Hz,576i@50Hz,576p@50Hz,720p@50/60Hz,

1080i@50/60Hz,1080p@50/60Hz 4Kx2K@25/30Hz,4Kx2K@25/30Hz

Supportrs 20~60KHz IR devices

1x HDMI

1x FO, 1x HDMI

1x IR Out

-4˚ ~ 140˚F (-20˚ ~ 60˚C)

20~90% RH (no condensation)

10.2Gpbs

5Vp-p(TTL)

≤14dB

≥-11dBm

≤-32dBm

15dB

1x FO,

Type A (19 pin female)

SC Single Mode

2 X DC 5V/2A

4W Max (each)

5.9” x 3.7” x0.9”

0.8 lbs

32˚ ~ 140˚F (0˚ to 60˚C)

1x IR IN

www.avenview.com

Page

11

6. PIN & WIRING STANDARD DEFINITION

TYPE A (RECEPTACLE) HDMI

Pin 1 TMDS Data2+ Pin 11 TMDS Clock Shield

Pin 2 TMDS Data2 Shield Pin 12 TMDS Clock–

Pin 3 TMDS Data2– Pin 13 CEC

Pin 4 TMDS Data1+ Pin 14 Reserved (N.C. on device)

Pin 5 TMDS Data1 Shield Pin 15 SCL

Pin 6 TMDS Data1– Pin 16 SDA

Pin 7 TMDS Data0+ Pin 17 DDC/CEC Ground

Pin 8 TMDS Data0 Shield Pin 18 +5V Power

Pin 9 TMDS Data0– Pin 19 Hot Plug Detect

Pin 10 TMDS Clock+

7. OPTICAL FIBER HAZARD

P

•

ersons installing fiber

goggles and observing warning signs.

• To ensure that the required personnel and equipment is properly installed, secure from unnecessary failure of the
components or failure of the whole system, injury to one’s self and in addition to legal responsibility; everyone is
responsible for his own health

Keep exposed optical fiber ends away from skin and eyes.

•

• The waste fragments should be treated with care and not picked up with bare hands, but rather with special gloves.

• Dispose of waste in a suitable container via an approved agency. Make sure that the quantity of optical fiber waste is

minimized.

• Closures containing termination points for optical fiber cabling must be labeled with appropriate warning signs or clearly
visible text.

• Make sure that the quantity of optical fiber waste is minimized. Closures containing termination points for optical fiber
cabling must be labeled with appropriate warning signs or a clearly viewable text.

There are four laser Classifications based on risk levels. Laser manufacturers are required to label their lasers accordingly.

•

optic products must take all necessary safety precautions, such as wearing protective clothing and

www.avenview.com

Page

12

Avenview Warranty Certificate

AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.

LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [e-mail].

PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact

[e-mail].

To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented

to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.

NOT COVERED BY THIS WARRANTY

This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of A venview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).

AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR

CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATI ON; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIR ECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.

Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

1100 Military Road, Kenmore, NY 14217

1.866.508.0269

www.avenview.com

Control Your Video

TECHNICAL SUPPORT

USA Head Office

Avenview Corp.
1100 Military Road
Kenmore, NY 14217
Ph: [phone]
Fax: [phone]

Email: [e-mail]

Disclaimer

While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.

Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.

Canada Sales

Avenview
151 Esna Park Drive, Units 11 & 12
Markham, Ontario, L3R3B1
Phone: [phone]
Fax: [phone]
Email: [e-mail]

Avenview Europe

Email: [e-mail]

Avenview Hong Kong

Email: [e-mail]