Page 1
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
Control Your Video...
CABLES & ACCESSORIES
4K DisplayPort Extender over
Single SC Fiber Optic Cable
WQXGA
2560x1600
© 2015 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.
Model #: FO-DP4K-300-EMIX
Page 2
Product Application & Market Sectors
Corporate House Of Worship
Military Residential
Education Industrial
Medical Aviation
www.avenview.com
Page 3
www.avenview.com
Page
TABLE OF CONTENTS
1. GETTING STARTED ..........................................................................................................................1
1.1 IMPORTANT SAFEGUARDS
1.2 SAFETY INSTRUCTIONS
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
2.
INTRODUCTION ..............................................................................................................................3
2.1
PACKAGE CONTENTS .....................................................................................................................4
3. APPLICATION DIAGRAM ..................................................................................................................5
4. PANEL DESCRITION.... ........................................................................................................................6
4.1 FRONT PANEL (Sender, FO-DP4K-300-EMIX-S) .......................................................................6
4.2 REAR PANEL (Sender, FO-DP4K-300-EMIX-S) ...........................................................................6
4.3 FRONT PANEL (Receiver, FO-DP4K-300-EMIX-S) .....................................................................7
4.4 REAR PANEL (Receiver, FO-DP4K-300-EMIX-S) ........................................................................7
5. INSTALLATION ...................................................................................................................................8
5.1 Before Installation ..........................................................................................................................9
5.2 Cable Specification .........................................................................................................................9
5.3 Installation Steps .. ........................................................................................................................10
6. OPTICAL FIBER HAZARD ..............................................................................................................10
..............................................................................................................1
....................................................................................................................1
........................... 2
7. GENERAL TROUBLESHOOTING ...................................................................................................11
7.1 Trouble Shooting depending on LED indicator status .................................................................11
8. CAUTION ..........................................................................................................................................11
9. DISPLAY PORT PIN ASSIGNMENT .................................................................................................12
10. SPECIFICATIONS ..............................................................................................................................13
3
Page 4
www.avenview.com
Page
1. GETTING STARTED
SECTION 1: GETTING STARTED
1.1 IMPORT
Please read all of these instructions carefully before you use the Fiber Optic cable. Save this manual for future
reference.
What the warranty does not cover
• Any product, on which the serial number has been defaced, modified or removed.
• Damage, deterioration or malfunction resulting from:
• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
• Repair or attempted repair by anyone not authorized by us.
• Any damage of the product due to shipment.
• Removal or installation of the product.
• Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
•
• Normal wear and tear.
• Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.
ANT
SAFEGUARDS
1.2 SAFETY INSTRUCTIONS
The Avenview FO-DP4K-300-EMIX, Display port Extender over fiber Optic has been tested for conformity to safety regulations
requirements, and has been certified for international use. However, like all fibre optic products, the FO-DP4K-300-EMIX
and
should be used with care. Read the following safety instructions to protect yourself from possible injury and to minimize the risk
of damage to the unit.
On no account should you:
! Look into a fiber while the system lasers are on;
! Use unfiltered handheld magnifiers or focusing optics to inspect fiber connectors;
! Connect a fiber to a fiberscope while the system lasers are on;
! Touch the end of the fiber connectors;
! Pull forcefully on the fiber cable;
! Reuse any specified fiber cleaning material more than once;
! Touch the clean area of a any specified fiber cleaning material;
! Use alcohol around an open flame or spark - Alcohol is Very flammable;
! Use alcohol or wet cleaning without a way to ensure that it does not leave residue on the polished connector;
! Dismantle the housing or modify the connector.
1
Page 5
www.avenview.com
Page
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with part 15 of the FCC rules. These limits are
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols Description
LASER RADIATION
DO NOT STARE INTO BEAM
< 1 MILLIWATT LASER DIODE
CLASS 2 LASER PRODUCT
Risk levels increase. These lasers emit a visible beam, from
400 to 780 Nanometres (nm), with an upper power limit of 1
milliwatt. An example is a (mw) bar code scanner.
Momentary viewing is not hazardous, but extended viewing
is. Laser protective eyewear is recommended for even
momentary viewing and necessary for extended viewing
DO NOT TAMPER WITH THE FIBER CABLE; DOING SO
WILL VOID THE WARRANTY AND CONTINUED USE
F THE PRODUCT.
O
designed to
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON
A SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.
2
Page 6
www.avenview.com
Page
2.
The Avenview FO-DP4K-300-EMIX-SET ULTRA HD Extender set over single SC optical fiber cable has been designed to
extend 4K (3840x2160 or 4096 x 2160) @60Hz video and multi-channel audio formats to any 4K compatible monitor up to 300m.
Video Signals: 4k2k@ 60 (ultra HD), 3D and full HD 1080p@60 Hz.
Audio signals: Multi-channel audio formats (DTS-HD Master Audio, Dolby TrueHD).
The FO-PD4K-300-EMIX-SET includes two (2) units: Sending unit (TX) FO-DP4K-300-EMIX-S and Receiving unit (RX)
FO-DP4K-300-EMIX-R with one (1) FTP output port which allows the user to extend video and audio up to 300m (1000ft).
The FO-DP4K-300-EMIX-SET input and output supports HBR2 cable assembly to handle upto 5.4Gbps/lane data rate.
The bonus features is the NEW box type design which can be easily installed into any enviroment, behind the monitor and
rack mounted on a rack shelf. This features has been added to the unit to give the installer and user a complete solution with
the new trends in rack mounted 4K sources streaming, network connected devices and new demand in Smart TV, ultra HD
monitors and content.
- Input: Displayport 1.2a with 3D & ULTRAHD, 1080p,DPCP compliant;
- Bandwidth: from 21.6 Gbps;
- Video Data Rate: 5.4 Gbps;
- HD resolutions: up to ULTRA HD (3840x2160/4096 x 2160@60Hz) WQXGA 25
- Audio supported: lpCM 7.1CH, Dolby TrueHD, Dolby Digital plus and DTS-HD Master Audio;
- Audio transmission: (32-192kHz sample rate);
- MST (Multi-Stream) Supported;
- Distance: up to 300 meters over OM3 SC Fiber Optic cable.
INTRODUCTION
60x1600@60Hz and 1080p (1920x1080@60Hz);
NOTE:
- MST will be supported if the source device can support MST.
- A DisplayPort 1.2 MST-capable hub.
- A DisplayPort 1.2 MST-capable monitor(s).
- Displaying 4K Ultra HD resolution would require the standard DisplayportI cable and display for accurate results.
3
Page 7
www.avenview.com
Page
2.1
Before you start the installation of the converter, please check the package contents.
PACKAGE CONTENTS
(FO-DP4K-300-EMIX-SET)
FO-DP4K-300-EMIX-S (TX)
1
X1
FO-DP4K-300-EMIX-R (RX)
2
POWER ADAPTER (5V/2A DC) X2
DISPLAYPORT (COPPER CABLE - 3FT) X 2
3
USER ’S MANUAL
4
X1
X 1
4
Page 8
www.avenview.com
Page
3.
APPLICATION DIAGRAM
5
Page 9
www.avenview.com
Page
4.
PANEL DESCRIPTION
4.1 FRONT PANEL (Sender, FO-DP4K-300-EMIX-S)
1
1.
LED LIGHT: Green light indicates an active
connection.
MODE: A. Default mode: video output level is set low to increase compatibility with equipment that is
3.
sensitive to jitter characteristics
B. Manual mode: video output level is set high to increase compatibility with equipment that is
sensitive to EYE pattern characteristics
2
2.
3
DISPLAYPORT IN:
4.2 REAR PANEL (Sender, FO-DP4K-300-EMIX-S)
1 2
Displayport cord interface
1.
OPTICAL OUT: Connect SC type connector
OM3 rated fiber For media streaming
linking to Receiver
2.
5V 2A Power Supply Jack: Connect provided
power adapter for power supply
6
Page 10
www.avenview.com
Page
4.3 FRONT PANEL (Receiver, FO-DP4K-300-EMIX-R)
1 2
LED Light: Green light indicates an active
1.
connection.
3.
MODE: A. Default mode: enable link training and automatically attempts to match the monitor output
B. Manual mode: disable link training and pre-set the output signal characteristics (most
compatible setting values is pre-set based on testing of different displays)
2.
3
Displayport OUT
4.4 REAR PANEL (Receiver, FO-DP4K-300-EMIX-R)
1.
OPTICAL IN: Connect SC type connector
OM3 rated fiber For media streaming
linking to Sender
1 2
2.
5V 2A Power Supply Jack
7
Page 11
www.avenview.com
Page
5.
This product is composed of a Transmitter and a Receiver.
The Transmitter should be connected to the source (Computer’s Displayport ) and the Receiver should be connected the
Displayport of the digital display device (Monitor). Avenview FO-DP4K-300-EMIX-SET Transmitter / Receiver is designed to
be used with SC type standard optical cable (Multi-Mode optical fiber: 50/125, 62.5/125um)
INSTALLATION
Note: The Transmitter and the Receiver modules must be connected to the included power supplies for proper operation.
Transmitter module must be powered on first.
8
Page 12
5.1 BEFORE INSTALLATION
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or
high humidity.
Use the DC power adapter with correct specifications and supplied with the unit. If improper
power supply is used the unit may malfunction and cause a fire.
Do not twist or pull by force ends of the video cable. It can cause malfunction.
5.2 CABLE SPECIFICATIONS
To achieve best results with our FO-DP4K-300-EMIX-SET we recommend a high quality displayport cable 22-24 AWG
cable with the below specifications to maintain signal integrity and distances.
NOTE: Misrepresentation with labels such as a DisplayPort 1.1 cable and DisplayPort 1.2 cable. A standard DisplayPort
cable, including the label DisplayPort 1.1 cable, will work for any DisplayPort configuration including the new capabilities
enabled by DisplayPort 1.2, including 4K and multi-stream capabilities. All standard DisplayPort cables support RBR,
HBR (High Bit Rate), and HBR2 (High Bit Rate 2), which can support 4K at 60Hz, or up to four 1080p displays using
multi-stream.
NOTE: For more reliable signal transmission we HIGHLY recommend using the MOLEX DP cable included in the package.
This type of DisplayPort cable has been tested extensively and showed best compatibility with FO-DP4K-300-EMIX-SET
FEATURES:
- Any DisplayPort™ 1.2 Cable with latches and provides a secure, connection between your DisplayPort-equipped
devices.
- Any DisplayPort™ cable that supports high resolutions of up to Ultra HD 4k x 2k (3840 x 2160/4096 x 2160) @ 60Hz with a
maximum HBR2 bandwidth of 21.6 Gbps. Also supports Multi-Stream (MST) for daisy chaining multiple monitors and
provides optional audio support.
www.avenview.com
Page
9
Page 13
www.avenview.com
Page
5.3 Installation Steps:
1. Connect the Transmitter module to the Displayport source device.
2. Connect the Receiver module to the display.
3. Connect a single strand multi-mode SC terminated optic fiber (50/125um) from the Transmitter to the Receiver module.
4.
Connect the included +5V DC power supply into the Receiver.
5. Blue LED indicator on the modules will be light up after all connections are completed.
6. OPTICAL FIBER HAZARD
P
•
ersons installing fiber
goggles and observing warning signs.
• To ensure that the required personnel and equipment is properly installed, secure from unnecessary failure of the
components or failure of the whole system, injury to one’s self and in addition to legal responsibility; everyone is
responsible for his own health
Keep exposed optical fiber ends away from skin and eyes.
•
• The waste fragments should be treated with care and not picked up with bare hands, but rather with special gloves.
• Dispose of waste in a suitable container via an approved agency. Make sure that the quantity of optical fiber waste is
minimized.
• Closures containing termination points for optical fiber cabling must be labeled with appropriate warning signs or clearly
visible text.
• Make sure that the quantity of optical fiber waste is minimized. Closures containing termination points for optical fiber
cabling must be labeled with appropriate warning signs or a clearly viewable text.
• There are four l aser Classifications based on risk levels. l aser manufacturers are required to label their lasers accordingly.
optic products must
take all necessary safety precautions, such as wearing protective clothing and
10
Page 14
www.avenview.com
Page
7.
GENERAL TROUBLESHOOTING
Problem Possible Solutions
NO IMAGE
• Check if the pC power is on
• Check if connection to the computer and the monitor are correct.
• Turn the pC power off and on again.
• please use DC adapter (5V, 2A) included in the package for transmitter
and receiver.
LCD SCREEN DEFECTS APPEAR
• This product supports up to WQXGA resolution.
• Check the maximum resolution range of the graphics card.
7.1 Trouble Shooting depending on LED indicator status
Problem Possible Solutions
Check if monitor is powered on
No display TX Solid / RX Blink
No display TX Blink / RX Solid
No display TX Blink / RX Blink
•
Check if Display port source is selected on monitor input setting
•
•
Check if the pC and display are powered on and properly booted.
Check if optic fiber is connected properly.
•
•
Please make sure that power supply is connected into TX and RX.
Reset the system by de-plugging and re-plugging all conections
•
8. CAUTION
Do not put heavy object on top of the FO-DP4K-300-EMIX. It may cause product malfunction.
1.
Put the product on even and stable location. If the product falls down or dropped, it may get damaged.
2.
Keep away from high temperature (over 50°C), low temperature (under 0°C) or high humidity. It may cause a fire and
3.
injury by electrical shock.
Use DC power adapter with correct specification. Otherwise it may cause fire.
4.
Use the multimode (50/125um) optical fiber.
5.
6. Do not view directly laser module of transmitter or the end of the other side of optical cable connected to transmitter
with optical instrument.
7. Do not twist or pull by force either ends of the optical cable. It can cause malfunction. Minimum bending diameter is
45mm
NOTE: Optical fiber cords of different types and specifications should not be mixed.
Please note the color-coding of connectors for different fiber specs to make it easy to avoid confusion
11
Page 15
www.avenview.com
Page
9.
DISPLAYPORT PIN ASSIGNMENT
9.1 Transmitter
PIN
1
Main Link Lane 0+
2 Ground 9
3
Main Link Lane 0-
4
Main Link Lane +
5 Ground 12
6
Main Link Lane 1-
7
Main Link Lane 2+
SIGNAL
ASSIGNMENT
PIN
8 Ground 15 Auxiliary Channel +
10
11 Ground 18 Hot plug Detect
13 Configuration 1 20
14 Configuration 2
9.2 Receiver
PIN
1 Main Link Lane 0+ 8 Ground
2 Ground
Main Link Lane 0-
3
Main Link Lane 1+
4
SIGNAL
ASSIGNMENT
PIN
9
10
11 Ground 18 Hot plug Detect
SIGNAL
ASSIGNMENT
Main Link Lane 2-
Main Link Lane 3+
Main Link Lane 3-
SIGNAL
ASSIGNMENT
Main Link Lane 2-
Main Link Lane 3+
PIN
16 Ground
17 Auxiliary Channe l -
19 Return
N/C
PIN
Auxiliary Channel +
15
Ground
16
Auxiliary Channel -
17
SIGNAL
ASSIGNMENT
SIGNAL
ASSIGNMENT
5 Ground 12
Main Link Lane 1-
6
7
Main Link Lane 2+
Main Link Lane 3-
13 Configuration 1
14 Configuration 2
19 Return
N/C
20
12
Page 16
www.avenview.com
Page
10. SPECIFICATIONS
ITEM DESCRIPTION
MODEL FO-DP4K-300-EMIX-S FO-DP4K-300-EMIX-R
UNIT DESCRIPTION Displayport Extender Transmitter Displayport Extender Receiver
INPUT VIDEO PORT
INPUT RESOLUTION
DisplayPort
4K (3840X2160 and 4096 x 2160) @
60Hz WQXGA (2560x1600)@60Hz
and 1080p (1920x1080)@60Hz,
2560x1440, 2560x1600, 2560x1080
4K (3840X2160 and 4096 x 2160) @
60Hz WQXGA (2560x1600)@60Hz
and 1080p (1920x1080)@60Hz,
2560x1440, 2560x1600, 2560x1080
Optical
OUTPUT VIDEO PORT
OUTPUT RESOLUTION
OR SPACE
COL
CHROMA SUBSAMPLING
DIMESNIONS (L X W X H)
POWER SUPPLY
WEIGHT
OPTICAL
OPTICAL SOURCE
O/E CONVERTER
FIBER
FIBER TYPE
ENVIRONMENTAL
OPERATING TEMPERATURE 32˚ ~ 104˚F (0˚ to 40˚C)
STORAGE TEMPERATURE -4˚ ~ 140˚F (-20˚ ~ 60˚C)
RELATIVE HUMIDITY 20~90% RH (no condensation)
Up to 4K (3840X2160 and 4096 x
2160) @ 60Hz, 2560x1440,
Optical
Up to 4K (3840X2160 and 4096 x
2160) @ 60Hz, 2560x1440,
2560x1600, 2560x1080
By pass all color spaces as RGB, YPbPr, YCbCr, etc..
4K 4:2:0 10bits, 4:2:2 10/12bits, 4:4:4 8bits@60Hz
3.2" X 2.1" X 0.97"
5V 2A
1.5 lbs
850nm VCSEl
PIN photo Diode
Multi-Mode optical fiber (SC Type Connector)
50/125 µm Multi-mode glass fiber OM3 rated fiber
2560x1600, 2560x1080
DisplayPort
13
Page 17
www.avenview.com
Page
Notes
14
Page 18
www.avenview.com
Page
Notes
15
Page 19
Avenview Warranty Certificate
AVENVIE
W CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact support@avenview.com.
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
support@avenview.com.
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of A venview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATI ON; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIR ECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
oodward Avenue, Kenmore, NY 14217
275 W
1.866.508.0269
www.avenview.com
Page 20
Control Your Video...
TECHNICAL SUPPORT
USA Head Office
Office Avenview Corp.
275 Woodward Avenue
Kenmore, NY14217
Phone: +1.716.218.4100
Fax: +1.866.387-8764
Email: info@avenview.com
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.
Canada Sales
Avenview
151 Esna Park Drive, Units 11 & 12
Markham, Ontario, L3R3B1
Phone: 1.905.907.0525
Fax: 1.866.387.8764
Email: info@avenview.com
Avenview Europe
Avenview Europe
Demkaweg 11
3555 HW Utrecht
Netherlands
Phone: +31(0)85 2100 613
Email: info@avenview.eu
Avenview Hong Kong
Unit 8, 6/f., Kwai Cheong Centre,
50 Kwai Cheong Road,
Kwai Chung, N.T.
Hong kong
Phone: 852.3575.9585
Email: wenxi@avenview.com
Loading...