Avaya IP Office Release 6.1, 9608, 9611, 9620L, 9630G 9600 Series Phone User Guide

...

IP Office Release 6.1

TelephoneMagic.com

9600 Series Phone User Guide

Issue 02c - (28 October 2010)

While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in this document without the obligation to notify any person or organization of such changes.

Documentation disclaimer Avaya shall not be responsible for any modifications, additions, or deletions to the original published version of this documentation unless such modifications, additions, or deletions were performed by Avaya.

End User agree to indemnify and hold harmless Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in connection with, subsequent modifications, additions or deletions to this documentation, to the extent made by End User.

Link disclaimer Avaya is not responsible for the contents or reliability of any linked Web sites referenced within this site or documentation(s) provided by Avaya. Avaya is not responsible for the accuracy of any information, statement or content provided on these sites and does not necessarily endorse the products, services, or information described or offered within them. Avaya does not guarantee that these links will work all the time and has no control over the availability of the linked pages.

Warranty Avaya provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language, as well as information regarding support for this product, while under warranty, is available to Avaya customers and other parties through the Avaya Support Web site: http://www.avaya.com/support. Please note that if you acquired the product from an authorized Avaya reseller outside of the United States and Canada, the warranty is provided to you by said Avaya reseller and not by Avaya.

Licenses THE SOFTWARE LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE, HTTP://SUPPORT.AVAYA.COM/LICENSEINFO/ ARE APPLICABLE TO ANYONE WHO DOWNLOADS, USES AND/OR INSTALLS AVAYA SOFTWARE, PURCHASED FROM AVAYA INC., ANY AVAYA AFFILIATE, OR AN AUTHORIZED AVAYA RESELLER (AS APPLICABLE) UNDER A COMMERCIAL AGREEMENT WITH AVAYA OR AN AUTHORIZED AVAYA RESELLER. UNLESS OTHERWISE AGREED TO BY AVAYA IN WRITING, AVAYA DOES NOT EXTEND THIS LICENSE IF THE SOFTWARE WAS OBTAINED FROM ANYONE OTHER THAN AVAYA, AN AVAYA AFFILIATE OR AN AVAYA AUTHORIZED RESELLER, AND AVAYA RESERVES THE RIGHT TO TAKE LEGAL ACTION AGAINST YOU AND ANYONE ELSE USING OR SELLING THE SOFTWARE WITHOUT A LICENSE. BY INSTALLING, DOWNLOADING OR USING THE SOFTWARE, OR AUTHORIZING OTHERS TO DO SO, YOU, ON BEHALF OF YOURSELF AND THE ENTITY FOR WHOM YOU ARE INSTALLING, DOWNLOADING OR USING THE SOFTWARE (HEREINAFTER REFERRED TO INTERCHANGEABLY AS “YOU” AND “END USER”), AGREE TO THESE TERMS AND CONDITIONS AND CREATE A BINDING CONTRACT BETWEEN YOU AND AVAYA INC. OR THE APPLICABLE AVAYA AFFILIATE (“AVAYA”).

Avaya grants End User a license within the scope of the license types described below. The applicable number of licenses and units of capacity for which the license is granted will be one (1), unless a different number of licenses or units of capacity is specified in the Documentation or other materials available to End User. "Designated Processor" means a single stand-alone computing device. "Server" means a Designated Processor that hosts a software application to be accessed by multiple users. "Software" means the computer programs in object code, originally licensed by Avaya and ultimately utilized by End User, whether as stand-alone products or pre-installed on Hardware. "Hardware" means the standard hardware originally sold by Avaya and ultimately utilized by End User.

License types Designated System(s) License (DS). End User may install and use each copy of the Software on only one Designated Processor, unless a different number of Designated Processors is indicated in the Documentation or other materials available to End User. Avaya may require the Designated Processor(s) to be identified by type, serial number, feature key, location or other specific designation, or to be provided by End User to Avaya through electronic means established by Avaya specifically for this purpose.

Copyright Except where expressly stated otherwise, no use should be made of materials on this site, the Documentation(s) and Product(s) provided by Avaya. All content on this site, the documentation(s) and the product(s) provided by Avaya including the selection, arrangement and design of the content is owned either by Avaya or its licensors and is protected by copyright and other intellectual property laws including the sui generis rights relating to the protection of databases. You may not modify, copy, reproduce, republish, upload, post, transmit or distribute in any way any content, in whole or in part, including any code and software. Unauthorized reproduction, transmission, dissemination, storage, and or use without the express written consent of Avaya can be a criminal, as well as a civil, offense under the applicable law.

Third Party Components Certain software programs or portions thereof included in the Product may contain software distributed under third party agreements ("Third Party Components"), which may contain terms that expand or limit rights to use certain portions of the Product ("Third Party Terms"). Information regarding distributed Linux OS source code (for those Products that have distributed the Linux OS source code), and identifying the copyright holders of the Third Party Components and the Third Party Terms that apply to them is available on the Avaya Support Web site: http://support.avaya.com/Copyright.

Preventing toll fraud "Toll fraud" is the unauthorized use of your telecommunications system by an unauthorized party (for example, a person who is not a corporate employee, agent, subcontractor, or is not working on your company's behalf). Be aware that there can be a risk of toll fraud associated with your system and that, if toll fraud occurs, it can result in substantial additional charges for your telecommunications services.

Avaya fraud intervention If you suspect that you are being victimized by toll fraud and you need technical assistance or support, call Technical Service Center Toll Fraud Intervention Hotline at +1-800-643-2353 for the United States and Canada. For additional support telephone numbers, see the Avaya Support Web site: http://support.avaya.com Suspected security vulnerabilities with Avaya products should be reported to Avaya by sending mail to: securityalerts@avaya.com.

Trademarks Avaya and Aura are trademarks of Avaya, Inc. The trademarks, logos and service marks (“Marks”) displayed in this site, the documentation(s) and product(s) provided by Avaya are the registered or unregistered Marks of Avaya, its affiliates, or other third parties. Users are not permitted to use such Marks without prior written consent from Avaya or such third party which may own the Mark. Nothing contained in this site, the documentation(s) and product(s) should be construed as granting, by implication, estoppel, or otherwise, any license or right in and to the Marks without the express written permission of Avaya or the applicable third party. Avaya is a registered trademark of Avaya Inc. All non-Avaya trademarks are the property of their respective owners.

Downloading documents For the most current versions of documentation, see the Avaya Support Web site: http://www.avaya.com/support

Contact Avaya Support Avaya provides a telephone number for you to use to report problems or to ask questions about your product. The support telephone number is 1-800-242-2121 in the United States. For additional support telephone numbers, see the Avaya Web site: http://www.avaya.com/support

9600 Series Phone User Guide Page 2

Issue 02c (28 October 2010)IP Office Release 6.1

Contents

..................................................................... 418.5 Holding a Conference Call

..................................................................... 418.6 Transferring Calls Using Conference

Introduction1.

..................................................................... 91.1 Important Safety Information

..................................................................... 101.2 9620 Telephone

..................................................................... 111.3 9630 Telephone

..................................................................... 121.4 9640 Telephone

..................................................................... 131.5 9650 Telephone

..................................................................... 141.6 Status Letters

..................................................................... 151.7 Button Modules

..................................................................... 161.8 Phone Keys

..................................................................... 171.9 The Phone Stand

Making Calls2.

..................................................................... 202.1 En-Bloc Dialing

..................................................................... 212.2 Call Soft Key Options

..................................................................... 222.3 Calling from the Contacts List

..................................................................... 222.4 Calling from the Call Log/History

..................................................................... 232.5 Redialling a Previous Number

..................................................................... 232.6 Making a Page Call

..................................................................... 232.7 Withholding Your Number

..................................................................... 242.8 Adjust the Call Volume

..................................................................... 242.9 Muting a Call

..................................................................... 242.10 Ending Calls

Answering Calls3.

..................................................................... 273.1 Divert a Call to Voicemail

..................................................................... 273.2 Ignore an Incoming Call

..................................................................... 273.3 Answering a Page Call

..................................................................... 283.4 Call Pickup

Redialling4.

..................................................................... 304.1 Redial (Last Dialed Mode)

..................................................................... 304.2 Redial (Call Log Mode)

..................................................................... 304.3 Selecting Your Redial Mode

Holding and Parking Calls5.

..................................................................... 335.1 Holding Calls

............................................................................ 335.1.1 Holding a Call

............................................................................ 335.1.2 Taking a Call Off Hold

............................................................................ 335.1.3 Switching Between Calls

............................................................................ 335.1.4 Transfer a Held Call

..................................................................... 345.2 Parking Calls

............................................................................ 345.2.1 Park Using the Menu

............................................................................ 345.2.2 Unpark (Status Menu)

Transferring Calls6.

..................................................................... 366.1 Transfer to Voicemail

..................................................................... 366.2 Transferring a Held Call

Account Codes7.

..................................................................... 387.1 Forced Account Code Entry

..................................................................... 387.2 Manual Account Code Entry

Conference Calls8.

..................................................................... 408.1 Starting a Conference

..................................................................... 408.2 Adding a Call to a Conference

..................................................................... 408.3 Viewing Conference Details

..................................................................... 418.4 Dropping/Muting Parties

Headset/Handsfree Operation9.

..................................................................... 449.1 Headset Operation

............................................................................ 449.1.1 Headset Volume

............................................................................ 449.1.2 Default Handsfree Audio Path

..................................................................... 459.2 Handsfree Speaker Operation

............................................................................ 459.2.1 Speaker Volume

............................................................................ 459.2.2 Default Handsfree Audio Path

Contacts/Directory10.

..................................................................... 4810.1 Managing External Contacts

..................................................................... 4910.2 Viewing Contacts Details

..................................................................... 5010.3 Make a Call from the Directory

..................................................................... 5010.4 Using the Directory for Other Functions

..................................................................... 5110.5 Adding a New Contact

............................................................................ 5110.5.1 Add a Contact from the Call Log

..................................................................... 5210.6 Editing a Contact

..................................................................... 5210.7 Deleting a Contact

Call Log/History11.

..................................................................... 5511.1 Accessing the Call Log/History

..................................................................... 5511.2 Making a Call

..................................................................... 5611.3 Viewing Call Details

..................................................................... 5711.4 Deleting a Record

..................................................................... 5711.5 Deleting All Records

..................................................................... 5711.6 Adding a Record to Your Contacts

Voicemail12.

..................................................................... 6012.1 Message Waiting Indication

..................................................................... 6112.2 Checking Messages

..................................................................... 6212.3 Sending a Message

..................................................................... 6212.4 Mailbox Greeting

..................................................................... 6312.5 Email Mode

..................................................................... 6312.6 Changing Your Voicemail Code

..................................................................... 6312.7 Voicemail On/Off

..................................................................... 6312.8 Transfer to Voicemail

..................................................................... 6412.9 Send a Call to Voicemail

..................................................................... 6412.10 Visual Voice

Logging In/Out13.

..................................................................... 6713.1 Logging In

............................................................................ 6713.1.1 Logging In on a Phone Already in Use

............................................................................ 6713.1.2 Logging In on a Not Logged In Phone

............................................................................ 6713.1.3 Logging In on an Unregistered Phone

..................................................................... 6813.2 Logout

..................................................................... 6813.3 Lock

..................................................................... 6813.4 Unlock

..................................................................... 6913.5 Auto Lock

..................................................................... 6913.6 Changing Your Security PIN

Redirecting Calls14.

..................................................................... 7314.1 Follow Me

............................................................................ 7414.1.1 Follow Me To (Features Menu)

............................................................................ 7414.1.2 Follow Me (Status Menu)

............................................................................ 7414.1.3 Follow Me Here (Features Menu)

..................................................................... 7514.2 Forwarding Calls

............................................................................ 7714.2.1 Forward Unconditional (Status Menu)

9600 Series Phone User Guide Page 3

Issue 02c (28 October 2010)IP Office Release 6.1

............................................................................ 7714.2.2 Forward Unconditional (Features Menu)

............................................................................ 7814.2.3 Forward On No Answer (Status Menu)

............................................................................ 7814.2.4 Forward On Busy (Status Menu)

..................................................................... 7914.3 Do Not Disturb

............................................................................ 8014.3.1 DND On/Off (Features Menu)

............................................................................ 8014.3.2 DND Off (Status Menu)

............................................................................ 8014.3.3 Do Not Disturb Exceptions

..................................................................... 8114.4 Twinning

............................................................................ 8114.4.1 Mobile Twinning Control

..................................................................... 8214.5 Forward On Busy/No Answer (Features Menu)

Groups15.

..................................................................... 8515.1 Group Membership

............................................................................ 8515.1.1 Group Membership On/Off (Status Menu)

............................................................................ 8515.1.2 Group Membership On/Off (Features Menu)

..................................................................... 8615.2 Group Service Status and Fallback

15.2.1 Changing the Group Service Status

............................................................................ 87

(Features Menu)

15.2.2 Changing the Group Service Status (Status

............................................................................ 87

Menu)

............................................................................ 8815.2.3 Changing the Group Fallback

Button Features16.

..................................................................... 9116.1 Editing Your Programmable Buttons

..................................................................... 9216.2 Abbreviated Dial

..................................................................... 9216.3 Absence Text

..................................................................... 9216.4 Account Code

..................................................................... 9216.5 Automatic Callback

..................................................................... 9216.6 Breakout

..................................................................... 9216.7 Call Forward All

..................................................................... 9316.8 Call Park

..................................................................... 9316.9 Call Park to Other

..................................................................... 9316.10 Call Pickup

..................................................................... 9316.11 Call Pickup Any

..................................................................... 9316.12 Drop Call

..................................................................... 9316.13 Flash Hook

..................................................................... 9416.14 Group BLF

..................................................................... 9416.15 Hunt Group Night Service

..................................................................... 9416.16 Internal Auto Answer

..................................................................... 9416.17 Paging

..................................................................... 9416.18 Ringer Off

..................................................................... 9416.19 Self Administer

..................................................................... 9416.20 Send All Calls

..................................................................... 9516.21 Supress Digits

..................................................................... 9516.22 User BLF

Phone Settings17.

..................................................................... 9917.1 Mobile Twinning

..................................................................... 9917.2 Withhold Number

..................................................................... 9917.3 Redial Mode

..................................................................... 10017.4 En-Bloc Dialing

..................................................................... 10017.5 Auto Lock

..................................................................... 10117.6 Ringer Controls

............................................................................ 10217.6.1 Disabling the Ringer

............................................................................ 10217.6.2 Visual Alerting

............................................................................ 10217.6.3 Coverage Ring

............................................................................ 10317.6.4 Ring Sound

............................................................................ 10417.6.5 Ringer Volume

............................................................................ 10517.6.6 Internal Auto Answer

..................................................................... 10617.7 Display Controls

............................................................................ 10617.7.1 Display Brightness

............................................................................ 10617.7.2 Display Contrast

............................................................................ 10617.7.3 Call Timer Display

............................................................................ 10817.7.4 Last Call Duration Display

............................................................................ 10917.7.5 Display Language

............................................................................ 10917.7.6 Show Call Waiting

............................................................................ 10917.7.7 Inactivity Timer (Auto Return)

..................................................................... 11017.8 Volume and Sound

............................................................................ 11017.8.1 Button Clicks

............................................................................ 11017.8.2 Error Tones

............................................................................ 11017.8.3 Ringer Volume

............................................................................ 11117.8.4 Handset Volume

............................................................................ 11117.8.5 Headset Volume

............................................................................ 11117.8.6 Speaker Volume

............................................................................ 11117.8.7 Automatic Gain Control

............................................................................ 11117.8.8 Default Handsfree Audio Path

..................................................................... 11217.9 Backup/Restore

............................................................................ 11217.9.1 Backup

............................................................................ 11217.9.2 Restore

..................................................................... 11317.10 Viewing Information

Status Menu18.

..................................................................... 11618.1 Do Not Disturb

..................................................................... 11618.2 Follow Me To

..................................................................... 11718.3 Follow Me Here

..................................................................... 11718.4 Forward On Busy

..................................................................... 11818.5 Forward On No Answer

..................................................................... 11818.6 Forward Unconditional

..................................................................... 11818.7 Forwarded Here

..................................................................... 11918.8 Group Membership

..................................................................... 11918.9 Group Service Status

..................................................................... 11918.10 Mobile Twinning

..................................................................... 12018.11 Parked Calls

..................................................................... 12018.12 System Alarms

Short Codes19. System Administration20.

..................................................................... 12620.1 Checking the System Information

..................................................................... 12620.2 Setting the Date

..................................................................... 12720.3 Checking the Time Server Status

..................................................................... 12820.4 Setting the Time

..................................................................... 12820.5 Setting the Time Offset

..................................................................... 12920.6 System Shutdown

..................................................................... 13020.7 Memory Card Management

..................................................................... 13120.8 System Alarms

Menus21.

..................................................................... 13421.1 Features Menu

..................................................................... 13521.2 Status Menu

..................................................................... 13621.3 A Menu

Glossary22.

..................................................................... 13822.1 Abbreviated Ring

..................................................................... 13822.2 Appearance Button

..................................................................... 13822.3 Attention Ring

..................................................................... 13822.4 Auto Hold

..................................................................... 13822.5 Bridged Appearance Button

9600 Series Phone User Guide Page 4

Issue 02c (28 October 2010)IP Office Release 6.1

..................................................................... 13822.6 Call Appearance Button

..................................................................... 13822.7 Call Coverage Button

..................................................................... 13822.8 Coverage Ring

..................................................................... 13822.9 Do Not Disturb

..................................................................... 13922.10 Do Not Disturb Exceptions

..................................................................... 13922.11 Follow Me

..................................................................... 13922.12 Follow Me Here

..................................................................... 13922.13 Follow Me To

..................................................................... 13922.14 Forward on Busy

..................................................................... 13922.15 Forward on No Answer

..................................................................... 13922.16 Forward Unconditional

..................................................................... 14022.17 Group

..................................................................... 14022.18 Idle Line Preference

..................................................................... 14022.19 Internal Twinning

..................................................................... 14022.20 Line Appearance Button

..................................................................... 14022.21 Logged Out

..................................................................... 14022.22 Login Code

..................................................................... 14022.23 Missed Call

..................................................................... 14022.24 Missed Group Call

..................................................................... 14022.25 Mobile Twinning

..................................................................... 14122.26 Park Call

..................................................................... 14122.27 Park Slot Number

..................................................................... 14122.28 Ringing Line Preference

..................................................................... 14122.29 Short Codes

..................................................................... 14122.30 Small Community Network

..................................................................... 14122.31 System Administrator

..................................................................... 14122.32 System Phone User

..................................................................... 14122.33 Twinning

...............................................................................143Index

Contents

9600 Series Phone User Guide Page 5

Issue 02c (28 October 2010)IP Office Release 6.1

Chapter 1.

Introduction

9600 Series Phone User Guide Page 7

Issue 02c (28 October 2010)IP Office Release 6.1

Introduction:

Phone

Programmable

Buttons

Colour

Screen

Gigabit

Headset

Speaker

Phone

Button

Module

Support

9620L24NoNoYes

Yes

x 3

9620C24YesNoYes

Yes

–

9630G24No

Yes

x 3

964024YesNoYes

Yes

x 3

9640G24Yes

Yes

x 3

965024NoNoYes

Yes

x 3

9650C24YesNoYes

Yes

x 3

1. Introduction

This guide is for 9600 Series telephones supported by IP Office Release 6.1 running on IP Office 500 and 500v2 systems.

· 9600 Series Phones These are IP phones supported by IP Office and other Avaya telephone systems. The supported phones are the:

· Gigabit Support This column indicates that the phone natively supports Gigabit Ethernet. Other phones can support Gigabit through the use of a suitable Gigabit adapter.

· Unsupported Features The 9600 Series phones are supported on a number of Avaya telephone systems and support different features depending on the telephone system. This guide covers just features supported on an IP Office telephone system.

1.1 Important Safety Information

· ! Warning: This handset may pickup small metal objects such as metal pins or staples.

· During a power surge, EFT or ESD, calls may be dropped. After a power surge, EFT or ESD, it is normal for the

phone to restart.

· Using a cell phone, mobile phone, GSM phone or two-way radio in close proximity to an Avaya telephone might cause interference.

· The phone should not be connected directly to the outdoor telecommunication network.

9600 Series Phone User Guide Page 9

Issue 02c (28 October 2010)IP Office Release 6.1

1.2 9620 Telephone

The IP Office supports the 9620L and 9620C versions of the 9620 telephone.

The phone supports 12 programmable call appearance/feature buttons. The labels for 3 of these are displayed in the main display and can be controlled by the adjacent buttons to the right. You can use the up and down arrow keys to scroll the display. You can also use the left and right arrow keys to move through the button feature in pages of 3.

Functions can be assigned to the phone's call appearance/feature buttons by your system administrator or by yourself using self-administration . Note that you cannot replace call appearances features assigned to buttons by your system maintainer but you can replace other features. However also note there are features that the system maintainer can assign that are not available to you to assign. This guide just includes features that you can assign yourself if required.

9600 Series Phone User Guide Page 10

Issue 02c (28 October 2010)IP Office Release 6.1

1.3 9630 Telephone

The IP Office supports the 9630G version of the 9630 telephone.

Introduction: 9620 Telephone

The phone supports 24 programmable call appearance/feature buttons. The labels for 6 of these are displayed in the main display and can be controlled by the adjacent buttons to the right. You can use the up and down arrow keys to scroll the display. You can also use the left and right arrow keys to move through the button feature in pages of 6.

9600 Series Phone User Guide Page 11

Issue 02c (28 October 2010)IP Office Release 6.1

1.4 9640 Telephone

The IP Office supports the 9640 and 9640G versions of the 9640 telephone.

9600 Series Phone User Guide Page 12

Issue 02c (28 October 2010)IP Office Release 6.1

1.5 9650 Telephone

The IP Office supports the 9650 and 9650C versions of the 9650 telephone.

Introduction: 9640 Telephone

The phone supports 24 programmable call appearance/feature buttons. The labels for 3 of these are displayed in the main display and can be controlled by the adjacent buttons to the right. You can use the up and down arrow keys to scroll the display. You can also use the left and right arrow keys to move through the button feature in pages of 3.

In addition, the features of 16 of the 24 buttons (buttons 04 to 11 and 12 to 19) can be accessed as using the auxiliary feature buttons below the display. They are shown in two pages of 8 with the the SHIFT key next to the display used to switch between which page is being displayed at any time.

9600 Series Phone User Guide Page 13

Issue 02c (28 October 2010)IP Office Release 6.1

1.6 Status Letters

When your own extension name is shown on the second line of the display, for example when the phone is idle, the name may be followed by a series of letters. These letters are used to indicate your current status.

· B = Barred A B is shown on your phone's display when the system administrator has set you to outgoing call barred status. You will only be able to make internal calls while this is applied.

· D = Diverting (Forwarding) Calls A D is shown after your extension name on the phone's idle display when you have forward unconditional enabled.

· G = Group Member (In Group)

A G is shown after your extension name on the phone's idle display when have been configured as a member of a hunt group and your membership is enabled. While this is the case, you may receive calls targeted to the hunt group.

· N = No Calls (Do Not Disturb) An N is shown after your extension name on the phone's idle display when you have do not disturb enabled.

· O = Out of Service An O is shown on your phone's display when any of the groups of which you are enabled as a member is set to night service mode. In that mode calls to that group are diverted to its fallback if set or otherwise to voicemail if available.

· T = Twinned A T is shown after your extension name on the phone's idle display if it is internally twinned with your phone. Calls to you will alert on both phones and can be answered by you at either phone.

· R = Resilience An R is shown after your extension name on the phone's idle display your phone is working in resilience mode. This is used when there may have been a problem with the telephone system to which your phone was registered and another IP Office system is currently providing support for your phone. In this mode, some features may not be available and calls may be routed differently.

· S = System Alarm If you are configured as a system administrator , an S in the phone's display indicates a system alarm .

(IP500 V2 only)

126 131

9600 Series Phone User Guide Page 14

Issue 02c (28 October 2010)IP Office Release 6.1

Introduction: Status Letters

1.7 Button Modules

The addition of a button module allows the phone to support additional programmable buttons.

· Do not connect or disconnect a button module yourself. Your system administrator will arrange this if necessary. Failure to connect and restart the equipment in the correct order may cause the phone and or the button module to not function correctly.

9630, 9640 and 9650 Phones

All variants of these phones supports BM24 button modules. Each button module provides the phone with an additional 24 buttons which can be used as appearance buttons and or feature buttons .

Up to 3 button modules can be attached to a each phone. However the number of button modules supported by the telephone system may be limited by the total number of button modules attached to other phones on the telephone system.

9620

These phones do not support any additional button modules.

138 90

9600 Series Phone User Guide Page 15

Issue 02c (28 October 2010)IP Office Release 6.1

1.8 Phone Keys

Key

Description

Soft Keys - The keys below the display have variable functions. When the key is active, its function is

indicated by the text label above it.

Message - This key is used to access your voicemail system. By default this uses a series of menus on your phone's display.

Navigation Keys - Press the up and down arrow keys to scroll through lists. In some menus, you can also use the left and right arrow keys to enter and exit different levels of the menu. A menu option that accesses a sub-menu is indicated by the ... dots (ellipsis) icon after its name.

OK - The OK key normally matches the function offered by the left hand soft key below the screen. PHONE - This key is used to exit any menu you are in and return to the appearance buttons menu. During a

call it can also be used to toggle the options displayed on the appearance menu.

MENU - This key is used to access a menu for phone settings and information.

CONTACTS - This key is used to display the various directories (personal and shared) of names and

telephone numbers to which you have access.

CALL LOG / HISTORY - This key displays a record of you most recent answered, missed and

outgoing calls. The button is illuminated when you have new missed calls.

VOLUME - Press + plus or – minus on the Volume key to adjust the volume of the incoming call.

Separate volumes can be adjusted for the ringer, handset, headset and speaker.

HEADSET - This key is used to answer and end calls using a headset connected to the phones headset

socket. The button is lit when you are connected to a call using the headset.

MUTE - This key can be used to mute your speech to the currently connected call. The button is lit while

mute is active.

SPEAKER - This key is used to answer and end calls using the phone's handsfree speaker and

microphone. The button is lit when you are connected to a call handsfree.

FORWARD - Provides direct access to the forwarding menu options. This button is not press on the

9620 and 9650 models.

These keys have two roles:

· Appearance Keys - These button represent calls that you can make or receive.

· Feature Buttons - Those key not configured as appearance keys can be used for other functions.

The following keys are found on the phone:

54 57

110

72 72

· The CONFERENCE, DROP, HOLD, REDIAL and TRANSFER keys found on other Avaya phones are presented as

soft key functions when appropriate to the current call to which you are protected.

9600 Series Phone User Guide Page 16

Issue 02c (28 October 2010)IP Office Release 6.1

Introduction: Phone Keys

1.9 The Phone Stand

The phones all include a two-position stand that clips to the base of the phone as shown below. Once attached the stand can be used in either position to change the angle of the phone.

When changing the position of the stand, be sure to check that the stand has locked into the chosen position. A small plastic peg is located just under the phone's handset. This peg can be reversed to more securely anchor the handset when the stand places the phone in an upright position.

The angle of the phone can also be adjusted as shown below. The angle of the display on these phones can also be adjusted.

Other Stands

If the phone needs to be used in a situation other than on a desk, for example wall mounted, a number of other stand designs are available from Avaya. Contact your system maintainer.

9600 Series Phone User Guide Page 17

Issue 02c (28 October 2010)IP Office Release 6.1

Chapter 2.

Making Calls

9600 Series Phone User Guide Page 19

Issue 02c (28 October 2010)IP Office Release 6.1

2. Making Calls

If you are not already on a call, then you can just dial the number. The first available appearance button will be used for the call. Alternatively, you can press a specific appearance button in order to make a call using that button.

If the number you dial matches a user or group on the telephone system, the directory name of the user or group is shown and the call starts altering the target.

If the call is to a user, and they do not answer, you can set and callback by pressing CallBack and then ending the call by pressing Drop. When a callback is set, the when the user next uses their phone or ends their current call, the system will call you and when you answer, automatically make another call to the user.

2.1 En-Bloc Dialing

By default, when you start dialing a number on your phone, the phone immediately connects to the telephone system and starts passing the digits you dial to the phone system. You cannot correct the digits you have already dialed except by ending the call and starting again. Also if you pause dialing for too long the phone system may think that you have finished dialing and will attempt to connect the call using only the digits you have completed dialing so far.

En-bloc dialing allows you to compose and edit the number to dial on your phone's display before it is sent to the phone system to be dialed.

Through the phone's menus you can select whether you want to use traditional or en-bloc dialing when making calls. Your chosen setting is then applied whenever you are using a phone that supports en-bloc dialing.

Dialing a Number Using En-Bloc Mode

With no connected call on the phone, start dialing. Do not lift the handset or select headset or speaker before

dialing. You can use the right arrow key or the Bksp key to delete the previous digit dialed if you need to correct the

number or Clear to erase the whole number. When you have completed the number as required, you can select how you want to make the call.

· Lift the handset to start a call using the handset.

· Pressing the Call soft key or OK button to start the call using the phone's default handsfree audio path

(speaker or headset). You can also press one of your idle call appearance to make the call using that appearance.

· Press the Headset button to start the call on a headset connected to your phone.

· Press the Speaker button to start the call on your phone's handsfree speaker.

111

Enabling/Disabling En-Bloc Dialing

You can enable or disable your en-bloc dialing setting through the phone's Features menu.

Press the Features soft key if shown. To do this during a call, press the PHONE key and then press the

Features soft key. Use the up and down arrow keys to highlight Call Settings. Press Select.

Use the up and down arrow keys to highlight En-Bloc Dial.

Use Change button to select On or Off.

9600 Series Phone User Guide Page 20

Issue 02c (28 October 2010)IP Office Release 6.1

Making Calls: En-Bloc Dialing

2.2 Call Soft Key Options

The options displayed for the buttons at the bottom of the display will change dynamically to reflect actions that you can perform during calls or while the phone is idle.

· Account Enter an account code to associate with the call.

· Answer Answer a page call, turning it into a normal call.

· CallBack Set an automatic callback on the user that you have called but who has not answered. When they next end a call, the telephone system will call you and when answered, will automatically make a call to the user.

· Complete Complete the transfer of a held call. A Cancel option is also shown which will end the transfer attempt.

· Conference Put your current call on hold and present dial tone for you to dial the number you want to add to a conference with the held caller.

· Connect Take a call of hold.

· Dir Access the directory in order to select a number by name rather than dialing it. The type of names available in the directory is adjusted to match those suitable for use by the feature.

· Drop End the call.

· Ignore Quiet the ringer for the current alerting call. The call will continue alerting until either answered or it goes to voicemail.

· Pickup Answer the call that is held or alerting another user.

· Redial If there are outgoing numbers in your call log, display the list of those numbers.

· Transfer Put your current call on hold and present dial tone for you to dial the number to which you want to transfer the call.

· ToVM Send an alerting call to your voicemail.

9600 Series Phone User Guide Page 21

Issue 02c (28 October 2010)IP Office Release 6.1

2.3 Calling from the Contacts List

You can use any directory contacts to make a call. You can also use the directory in almost any telephone function where you need to select the number for a destination, for example during transfers.

Access the contacts directory:

Press the CONTACTS key. The directory menu is displayed.

Use the left and right arrow keys to select which type of directory entries you want displayed.

· All All directory entries.

· External Directory entries stored by the telephony system for all users to use.

· Groups The names and numbers of hunt groups on the telephone system.

· Users The names and numbers of other users on the telephone system.

· Personal Your own personal directory entries.

Use the the up and down arrow keys to scroll through the list or start dialing the name you want to find to

display only matching entries. If you dial a name to return to the full list press the Clear soft key. To view more details of the highlighted name, press Details. To return to the directory press List.

When the required entry is highlighted, press Call or press the button next to the name.

2. Continue as for a normally dialed call.

2.4 Calling from the Call Log/History

You can use the call log to make calls to the number included in the currently selected call record.

Access the call log.

Press the CALL LOG button.

The display will change to show your call log records. The caller's name is shown if known, otherwise the

number. If you have any new missed call records, the button is illuminated and the call log will open showing your missed calls.

Use the left and right arrow keys to select which call log records you are viewing. The options are All,

Missed, Incoming and Outgoing. Use the up and down arrow keys to scroll through the records.

Press Call to call the number displayed in the call record.

9600 Series Phone User Guide Page 22

Issue 02c (28 October 2010)IP Office Release 6.1

Making Calls: Calling from the Call Log/History

2.5 Redialling a Previous Number

When Redial is displayed it can be used in one of two ways, set by the phone's redial mode setting .

List Mode

This redial method is used when your phone's redial mode is set to List.

Access the redial list.

Press Redial. The list of outgoing calls is displayed.

Use the up and down arrow keys to scroll through the 10 most recent outgoing calls.

Press Call to call the number displayed in the call record.

2. Continue in the same way as for a normal dialed call.

One Number Mode

This redial method is used when your phone's redial mode is set to One.

Press Redial.

1. The number for the most recent outgoing call in your personal call log is redialed.

2. Continue in the same way as for a normal dialed call.

2.6 Making a Page Call

In order to make page calls you must have access to a paging short code provided by the system administrator or to a paging feature button.

If the dialing short code or the paging button have been pre-configured with a number, the user or group at that number will be paged if available.

The dialing short code can be configured to accept the number of the user or group to page when dialed. Similarly a paging button can be set to allow number entry when pressed as follows:

Press the paging button.

1. Dial the number of the user or group you want to page.

2. When the dialing is completed, the page call is made.

· If the destination is a user and they already have a call connected, they cannot be paged. If the destination is a group which is not in service or has no available members, it cannot be paged.

Feature Button

The self-administer function can be used to assign a feature button as a page button using the Group Paging action.

2.7 Withholding Your Number

You can select to withhold your number on external calls. Note that this option may not be supported in all situations. It may depend on the configuration of your phone system and options supported by your telephone line provider.

Press the Features soft key if shown. To do this during a call, press the PHONE key and then press the

1. Features soft key.

Use the up and down arrow keys to highlight Call Settings. Press Select.

2. Use the up and down menu keys to highlight Withhold Number.

3. Press Change to switch the option On or Off.

4. Press Save.

9600 Series Phone User Guide Page 23

Issue 02c (28 October 2010)IP Office Release 6.1

2.8 Adjust the Call Volume

While talking, you can adjust the volume of the incoming call. The volume is separately adjusted for which every device you are currently using (handset, headset or speaker).

With the call connected, press the VOLUME key.

1. Use the + plus and – minus keys to adjust the volume.

2. The display will return to normal after a few seconds.

2.9 Muting a Call

Muting a call stops the caller from hearing you. However you can still hear them.

· The mute setting remains active even if you switch between calls using hold and or appearance buttons.

· If you change how you are listening to the call, for example switching from the handset to the speaker, the mute

setting is canceled.

To activate mute, press the

1. To switch mute off, press the key again.

MUTE key. The button will be lit while mute is active.

2.10 Ending Calls

· The Drop option can be used to end the currently highlighted call on the display.

· If the call is connected on the phone's speaker, the

· If the call is connected on the phone's headset, the HEADSET key is lit. Pressing the key again will end the call.

· If the call is connected on the phone's handset, replacing the handset will end the call.

SPEAKER key is lit. Pressing the key again will end the call.

9600 Series Phone User Guide Page 24

Issue 02c (28 October 2010)IP Office Release 6.1

Chapter 3.

Answering Calls

9600 Series Phone User Guide Page 25

Issue 02c (28 October 2010)IP Office Release 6.1

3. Answering Calls

A slow flashing red lamp on an appearance button indicates an alerting call. This may also be accompanied by ringing

101 102

and by the message lamp flashing .

Selected Button

If you are currently not on a call, you can answer the alerting call in the following ways:

Select the method which you want to use to talk to the caller:

· To quiet the ringing, press the Ignore soft key. The call will still continue alerting visually and can be answered or ignored.

· To redirect the call to voicemail, press the To VM soft key.

· To answer the call using the handset, lift the handset.

· To answer the call handsfree, press the SPEAKER key.

· To answer the call on a headset, press the HEADSET key.

· Just pressing the key will answer the call either on the speaker or headset depending on the phone's audio

Once you have answered the call, you can switch between different talk modes:

· To switch to using the handset, lift the handset.

· To switch to handsfree, press the SPEAKER key. If you were using the handset you can now safely replace

path setting.

it.

· To switch to headset mode, press the HEADSET key. If you were using the handset you can now safely replace it.

· If you have answered the call on the speaker or headset, pressing the SPEAKER or HEADSET key again before you select another mode will end the call.

· Just pressing the key or any other appearance button will put the current call on hold.

Answering Another Call

If you are already on a call, answering a new call will automatically put the existing call on hold. Drop.

Using the up and down arrow keys, scroll the display highlight the waiting call.

· To quiet the ringing, press the Ignore soft key. The call will still continue alerting and can be answered or ignored.

· To redirect the call to voicemail, press the To VM soft key.

To answer the call press the button. Your existing call will be put on hold.

[1]

unless your first press

Notes

This guide assumes that auto hold is enabled (the default). The system administrator can disable auto hold for the

1. system, in which case calls are automatically disconnected rather than held.

9600 Series Phone User Guide Page 26

Issue 02c (28 October 2010)IP Office Release 6.1

Answering Calls:

3.1 Divert a Call to Voicemail

You can transfer a call targeted at you directly to your voicemail mailbox.

If the call is not the currently highlighted call on the display, use the up and down arrow keys to highlight it.

1. Press the To VM soft key. The call is redirected to your mailbox.

3.2 Ignore an Incoming Call

You can quiet the ringer of a currently alerting call. The call will continue alerting visually but with no audible ring.

If the call is not the currently highlighted call on the display, use the up and down arrow keys to highlight it.

1. Press the Ignore soft key.

2. The call will continue alerting but with no audible ring.

3.3 Answering a Page Call

Your phone can be paged if you have no other connected call in progress. The page is heard through the phone's speaker.

A page call is indicated in the display by the word Page.

· To answer the page call, press the Answer soft key. The call is turned into a normal call.

· To ignore the page call, press the Drop soft key.

9600 Series Phone User Guide Page 27

Issue 02c (28 October 2010)IP Office Release 6.1

3.4 Call Pickup

Pickup is used to answer a call ringing elsewhere on the phone system. There are a number of pickup options:

· Answer any ringing call on the telephone system.

· Answer a call ringing a particular user.

· Answer a call ringing a particular group.

· Answer a call, not necessarily a group call, ringing the members of a group.

Press the Features soft key if shown. To do this during a call, press the PHONE key and then press the

1. Features soft key.

Use the up and down arrow keys to highlight Pickup. Press Select.

· To answer a ringing call, press the Any soft key.

· To answer a call ringing against a particular target, dial the targets number. Alternatively, press the Dir soft

key to select the target from the directory .

The following menus will depend on the type of number entered:

· User Number

· To answer a call ringing against the user, press the Pickup soft key.

· To return to entering a number, press the Clear key.

· Hunt Group Number

· To answer a call ringing against the members of the group, press the Members soft key. The call does not

have to be a call to the hunt group.

· To answer a call ringing for the hunt group, press the Group soft key.

· To return to entering a number, press the Clear key.

Default Short Codes

Short codes are numbers that you can dial to enable and disable various features. The following are default short codes that may be available. Your system administrator will confirm any additional short codes that they may have configured for your use.

· Pickup Any Call: *30

Answer a call ringing on the telephone system.

· Pickup a Group Call: *31

Answer a call ringing a group of which you are a member.

· Pickup a Users Call: *32*N#

Pickup a call ringing a user's extension number (N).

· Pickup a Group Members Call: *53*N#

Pickup a call ringing the members of a group (N). This does not necessarily have to be a group call.

9600 Series Phone User Guide Page 28

Issue 02c (28 October 2010)IP Office Release 6.1

Chapter 4.

Redialling

9600 Series Phone User Guide Page 29

Issue 02c (28 October 2010)IP Office Release 6.1

4. Redialling

The phones redial operation can work in either of the following modes:

· Open Call Log If this mode is selected, pressing Redial will display a menu of the 10 most recent outgoing calls in your call log. You can select the call that you want to redial and perform a number of other functions.

· Last Dialed If this mode is selecting, pressing Redial will immediately repeat the most recent outgoing call in your call log. None of the other redial functions will be accessible.

You can select the redial mode that the phone uses. In either case, the redial function uses the outgoing call records in your personal call log . If you delete the records in your call log, redial will not work until new outgoing call records exist in your personal call log.

Note

Use of centralized call log can be switched off by the system administrator. In that case the numbers used for the

1. redial function are stored by the phone. This guide only covers redial using outgoing call records in the user's centralized call log.

4.1 Redial (Last Dialed Mode)

This redial method is used when your phone's redial mode is set to One.

Press Redial.

1. The number for the most recent outgoing call in your personal call log is redialed.

2. Continue in the same way as for a normal dialed call.

4.2 Redial (Call Log Mode)

This redial method is used when your phone's redial mode is set to List.

Access the redial list.

Press Redial. The list of outgoing calls is displayed.

Use the up and down arrow keys to scroll through the 10 most recent outgoing calls.

Press Call to call the number displayed in the call record.

2. Continue in the same way as for a normal dialed call.

4.3 Selecting Your Redial Mode

You can select whether your phone uses the redial list or last call redial mode.

Press the Features soft key if shown. To do this during a call, press the PHONE key and then press the

1. Features soft key.

Use the up and down arrow keys to highlight Call Settings. Press Select.

2. Use the up and down arrow keys to highlight Redial Action.

4. The current mode, Open Call Log or Last Dialed is displayed.

· Last Dialed If this mode is selecting, pressing Redial will immediately repeat the most recent outgoing call in your call log. None of the other redial functions will be accessible.

Press Change to change the mode.

6. When the required mode is displayed, press Save.

9600 Series Phone User Guide Page 30

Issue 02c (28 October 2010)IP Office Release 6.1

+ 118 hidden pages

Avaya IP Office Release 6.1, 9608, 9611, 9620L, 9630G 9600 Series Phone User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual