Avaya Asynchronous Connectivity via CLAN User Manual
Asynchronous Connectivity via CLAN (TN799B) for DEFINITY®
FEATURE: This feature will provide the capability for Services to access the switch via TCP/IP
using remote SAT (DSA). Remote Sat capability via TCP/IP will provide increase data speeds over
existing speeds. System Application Limits : System Management G3r: 8 , G3si, csi : 5 ,
DEFINITY ONE® : N/A.
Purpose : This Job-Aid illustrates the capability to access DEFINITY®ECS via TCP/IP using
BCMSVU R2V2 (and later) and DEFINITY SITE ADMINISTRATION (DSA).
SECURITY: Service requests by the client applications will be accepted on user administered IP
addresses and TCP port numbers. In addition, the user will be able to specify explicit IP addresses
that DEFINITY® ECS can accept client requests from.
Step : Description
1 : change system parameters maintenance page 2 of 3
§ Verify that Packet Intf1 and Intf2 are set to yes
§ See NOTE for Bus Bridge administration
2 : list configuration all to verify that CLAN board is present in example 1A07
3 : add data-module <ext>
§ Pick an extension from a list that was dedicated for the data-module.
§ The port type must be selected as Ethernet (depress the <HELP> key)
§ The Port will be the 17th port on the board location i.e.. 1A0717
§ The Link should be selected as : 1 (Range = 1-25)
§ The Name should be selected as CLAN
4 : Display port 1A0717
Verify that the Port information is administered correctly with the previous input
5 : list configuration board 1a07
Verify that port 17 on the CLAN board is now assigned
Step : Description
7 : Confirm DSA Computer and BCMSVU Server IP Address:
§ Click on Start / Run / CMD
§ At the DOS Prompt type : ipconfig /all | more
§ This will return your Computer Name (Node-Name) and IP Address.
§ For DSA and BCMSVU the IP Address should be static ( NOT DHCP).
8 : change node-names ip
§ add the node-name of the CLAN Board and IP Address
§ add the node-name of the DSA Computer and IP Address
§ add the node-name of the BCMSVU Server and IP Address
9 : change ip-interface
§ Enter the data required as shown .
§ Verify the Subnet Mask and Gateway Address (as provided by LAN/WAN
Administrator)
10 : change ip-services
§ Enter the data for the SAT as shown :
§ Service Type : SAT
§ Enabled : Y
§ Port : 5023
§ Local Node : CLAN
§ Remote Node : DSA Computer Node-Name
§ Remote Port : 0
11 : Verify the status Link
12 : Verify the Status of the data-module
13 : Verify the status of the ip-board
14 : Administer the DSA Application
6 : display communication-interface links
§ The link ( 1 ) should be shown as administered.
§ The link is administered in step 3, this step is only a verification.
§ Verify the data shown is correct.
NOTE :
Verify Node-Names, IP-Address, Gateway Address with Local LAN/WAN Administrator.
Also check the * Microsoft® Support Knowledge Base Troubleshooting Wizards:
Article ID : Q163391; Q113342 ; Q102908 for additional assistance
http://search.support.microsoft.com/kb
http://search.support.microsoft.com/kb/c.asp?fr=0&SD=GN&LN=EN-US
* Microsoft®, Win32, MS-DOS, Windows, and Windows NT are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
15 : Administer the BCMSVU Server Application
IP-SAT / BCMSVU on DEFINITY
ECS R9r, ECS R9si, ProLogix R9csi
Provided by:
jwysocki@avaya.com
05/01/2001 18:30 Hrs
Page 1 of 6
The following Tasks are required for activation
On DEFINITY ECS R9csi (ProLogix), ECS R9si, ECS R9r
change system-parameter maintenance page 2 of 3
1
SPE OPTIONAL BOARDS
Packet Intf1? Y Packet Intf2? Y
* Bus Bridge : 01A07
* Inter-Board Link Timeslots Pt0 : 6 Pt1 : 1 Pt2 : 1
NOTE: * Only On DEFINITY R9csi (ProLogix).
Refer to Page 6 of 6
List configuration all or
2
List configuration Board <CLAN Bd Loc >
Bd # BdType Code Vint Assigned Ports
u=unassigned t=tti p=p sa
1A07 CLAN TN799B 000001 u u u u u u u u
u u u u u u u u
u
Add data-module 40000
3
Data Extension : 40000
Type : Ethernet
Port : 01A0717
Link : 1
( Node) Name : CLAN
Display Port 1A0717
4
PORT INFORMATION
Port : 1A0717
Equipment Type : Data Module
Identification : 40000
List configuration all or
5
List configuration Board <1a07 >
IP-SAT / BCMSVu Server
display communication-interface links
6
INTERFACE LINKS
Link Enable Est Ext Type Dest DTE Conn Name
Conn Number DCE Mod
1 Y N 40000 Ethernet CLAN
2
:
25
Confirm DSA Computer and BCMSVU Server IP Address:
7
§ Click on Start / Run / CMD
§ At the DOS Prompt type : ipconfig /all | more
§ Note the following items:
§ Computer Name
§ IP-Address
§ For DSA and BCMSVU the IP Address should be static ( NOT DHCP).
8
change node-names ip
Name IP Address
default 0 . 0 . 0 . 0
NJ7460JWYSOCKI 135.8.32.??
NJ7460HUGHJOHN 135.8.32.??
bcmsvuserver 192.168.0 .2
CLAN 192.168.0.3
change ip-interfaces
9
IP INTERFACES
Enable Net
Eth Pt TYPE SLOT CODE Sfx Node Name Subnet Mask Gateway Address Rgn
Y C-LAN 01A07 TN799 B CLAN 255.255.252.0 135.8.12.1 1
change ip-services
10
Service Enabled Local Local Remote Remote
Type Node Port Node Port
SAT y CLAN 5023 NJ7460JWYSOCKI 0
SAT y CLAN 5023 NJ7460HUGHJOHN 0
SAT y CLAN 5024 bcmsvuserver 0
Bd # BdType Code Vint Assigned Ports
u=unassigned t=tti p=p sa
1A07 CLAN TN799B 000001 u u u u u u u u
u u u u u u u u
17
IP-SAT / BCMSVU on DEFINITY
ECS R9r, ECS R9si, ProLogix R9csi
Provided by:
jwysocki@avaya.com
05/01/2001 18:30 Hrs
Page 2 of 6
Loading...