Avaya 4600, 5600 IP User Manual

For all IP Telephone documentation,
go to Http://www.avaya.com/support

Gigabit Ethernet Adapter

For 4600 & 5600 Series

Installation and Safety Instructions

16-601543

Issue 2

August 2014

IP

Phones

End of support for Gigabit Power over Ethernet Adapter

The Gigabit Power over Ethernet Adapter is no longer supported by Avaya.
For more information, see https://downloads.avaya.com/css/P8/documents/100074552

.

IMPORTANT USER SAFETY INSTRUCTIONS

The most careful attention has been devoted to quality standards in the manufacture of your new Gigabit
Ethernet Adapter. Safety is a major factor in the design of every Avaya Product. But, safety is YOUR
responsibility too. Please read carefully the helpful tips listed below. These suggestions will enable you t o
take full advantage of this product. Then, retain these tips for later use.

WARNING:

This product is NOT for residential use. It is for business systems applications ONLY.
Do not plug a standard RJ-45 cable from an 1151A, 1151B, or 1151C device into the Ethernet input of this
device or it will render this device permanently non-functional. A separate special power cable is required if
using an 1151 type device. See page 5 for configuration information.

Use

When using your Gigabit Ethernet Adapter, the following safety precautions should always be followed to
reduce the risk of fire, electric shock, and injury to persons.

Read and understand all instructions.
Follow all warnings and instructions marked on the product and contained in its packaging.
This product is for use only with specified Avaya equipment as outlined in the attached materials or

available on http://www.avaya.com/support. No other use of this product is recommended or warranted.

This device can be hazardous if immersed in water. Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. To avoid the
possibility of electric s hock , do not use it while you are wet. If you accidentall y dro p the Gigabit Ethernet
Adapter into water, do not retrieve it until you have first unplugged the power cord from the AC wall receptacle
(or other AC power source) if using an 1151C1 power suppl y, then unplugged the power cable to the Gigabit
Ethernet Adapter. Then call service personnel to ask about a replacement.

Do not allow anything to rest on the DC power cord. Do not locate this product where the cord will be
abused, such as by persons walk ing on it.

Allow adequate ventilation for the product. Do not cover or install in a confined space that may prevent

cooling and allow excessive heat build-up.

To reduce the risk of electric shock, do not disassemble this product. There are no user serviceable parts.
Opening or r emoving covers may expose you to hazardous voltages. Incorrect reassembly can cause electric
shock when the product is subsequently used.

Service

Before cleaning or removing from service, unplug the DC power cable from the Gigabit Ethernet Adapter,
unplug the power cord from the AC wall receptacle (or other AC power source) if using an 1151C1 power
supply, then unplug the power cable to the Gigabit Ethernet Adapter. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.

Be sure to disconnect all cords from this product and refer servicing to qualified service personnel when
these conditions exist:

-- If the power cable is damaged or frayed.

-- If liquid has been spilled into the product.

-- If the product has been e xpose d t o rain or water.

-- If the product has been dropped or the housing has been damaged.

1

2

-- If you note a distinct change in the performance of the product.

Declaration

To download the Declaration of Conformity (DoC) for this equipment, visit http://www.avaya.com/support

of

Conformity

SAVE THESE INSTRUCTIONS

When you see this warning symbol on the product, refer to this instructions booklet for more information
before proceeding.