Avago Technologies RAID 352 User Manual

AcceleRAID 352
Quick Installation Guide
DB11-000027-00 First Edition 08P5516
Electromagnetic Compatibility Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help. Shielded cables for SCSI connection external to the cabinet are used in the
compliance testing of this Product. LSI Logic is not responsible for any radio or television interference caused by unauthorized modification of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by LSI Logic. The correction of interferences caused by such unauthorized modification, substitution, or attachment will be the responsibility of the user.
The LSI Logic Mylex AcceleRAID 352 is tested to comply with FCC standards for home or office use.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiv er in a domestic en vironment, it may cause radio interference. Install and use the equipment according to the instruction manual.
LSI Logic Corporation North American Headquarters Milpitas, CA
408.433.8000
Declaration of Conformity
Per FCC Part 2, Section 2.1077(a)
Manufacturer’s Name: LSI Logic Corporation Manufacturer’s Address:
Declares that the product: Product Name: High Performance RAID Controller
Model Number(s): AcceleRAID 352
Year of Manufacture: 2000 Conforms to the following Product Specification(s):
FCC: CFR 47 Part 15, Subpart B, Section 15.107(e)
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
North American Headquarters Milpitas, CA
USA
and Section 15.109(g) Class B Digital Device tested per ANSI C63.4–1992 procedures
Declaration of Conformity
Per 89\336\EEC
Responsible Party Name: Address:
Trade Name: High Performance Caching RAID Controller Model Number(s):AcceleRAID 352 Fab. 550157-01 Rev. A
Standards: EN 50081-1:1992, Emissions
LSI Logic Corporation North American Headquarters Milpitas, CA
U.S.A.
hereby declares that the product
conforms to the following specifications
EN 55022 Class B (Radiated), Class B (Conducted)
EN 50082-1:1992, Immunity
EN 61000-4-2:1995 Electrostatic Discharge EN 61000-4-3:1996 Radiated Susceptibility EN 61000-4-4:1995 Electrical Fast Transients/Burst
Community of Europe
CE mark is rated for the AceleRAID 352 as follows: CISPR 22 Radiated Emission EN55022, Generic immunity standard for the following:
IEC 801-2 ESD, IEC 801-3 Radiated, and IEC 801-4 EFT/Burst Warning! This is a Class B product. In a residential environment this product may
cause radio interference, in which case the user may be required to take adequate measures.
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse B. In Wohnbereichen
können bei Betrieb dieses Gerätes Rundfunkstörungen aufreten, in welchen Fällen der Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.
Avertissement! Cet appareil est un appareil de Classe B. Dans un environnement résidentiel
cet appareil peut provoquer des brouillages radioélectriques. Dans ce cas, il peut être demandé à l’utilisateur de prendre des mésures appropriées.
Underwriters Laboratories Statement and Warning
Proprietary Rights Notice
This document contains proprietary information of LSI Logic Corporation. The information contained herein is not to be used by or disclosed to third parties without the express written permission of an officer of LSI Logic Corporation. Any product(s) described herein is/are a licensed product of LSI Logic Corporation.
Document Description
Document DB11-000027-00 First Edition. November 2002 This document describes the LSI Logic Corporation’s Mylex AcceleRAID 352 product for Software Kit 5.20 and will remain the official reference source for all revisions/releases of this product until rescinded by an update.
Disclaimer
It is the policy of LSI Logic to improve products as new technology , components, software, and firmware become available. LSI Logic Corporation reserves the right to make changes to any products herein at any time without notice. All features, functions, and operations described herein may not be marketed by LSI Logic in all parts of the world. In some instances, photographs and figures are of equipment prototypes. Therefore, before using this document, consult your LSI Logic representative for information that is applicable and current. LSI LOGIC DOES NOT ASSUME ANY RESPONSIBILITY OR LIABILITY FOR THE USE OF ANY PRODUCT(S) DESCRIBED HEREIN EXCEPT AS EXPRESSLY AGREED TO IN WRITING BY LSI LOGIC.
License Restriction
The purchase or use of an LSI Logic product does not convey a license under any patent, copyright, trademark, or other intellectual property right of LSI Logic or third parties.
Copyright Notice
Copyright © 2001, 2002. LSI Logic Corporation. All rights reserved.
Trademark Acknowledgments
LSI Logic, the LSI Logic logo, MORE, Mylex, and SANmapping are trademarks or registered trademarks of LSI Logic Corporation. All other brand and product names may be trademarks of their respective companies.
Contents
Hardware Installation
Introduction ........................................................................................ 1-1
Performing an Installation ..................................................................1-1
PCI Hot Plug ............................................................. ... ..............1-1
Connectors, Jumpers, and LEDs ...............................................1-1
Installing the AcceleRAID 352 into the System Board ...............1-5
What to Do Next ................................................................................1-7
SOFTWARE LICENSE AND WARRANTY POLICY
Manual No. DB11-00027-00 1
2 AcceleRAID 352 Installation Guide
Hardware Installation

Introduction

The AcceleRAID 352 is a versatile PCI to a dual channel Ultra 160 SCSI, Low Voltage Differential (LVD) RAID controller. There are many possible hardware configurations. This quick installation guide assumes that the user is familiar with controller, disk drive, and RAID terminology.

Performing an Installation

WARNING
To avoid electrical shock, do not attempt to perform this hardware installation with power on. Disconnect the system from the electrical wall outlet.

PCI Hot Plug

Please refer to Appendix D in the AcceleRAID 352 PCI to Ultra 160 SCSI RAID Controller Installation Guide for instructions on how to use the PCI
Hot Plug feature.

Connectors, Jumpers, and LEDs

There are two Ultra 160 SCSI external channels and two Ultra 160 SCSI internal channels supported on the controller. The SCSI connector locations are shown in Figure 1.
All the jumpers should normally be set to their default settings. See Table 1 for default jumper settings. Jumper locations are shown in Figure 2.
The front side of the controller has one LED that is described in Figure 3 and in Table 2. The back side of the controller has four LEDs that are mode indicators while the controller is running. These LEDs indicate single-ended mode and LVD m ode and are described in Figure 4 and in Table 3.
Manual No. DB11-00027-00 1
Performing an Installation
CH0 CH1
CH0
CH1
Figure 1. AcceleRAID 352 Controller with Channel Connectors
JP1 JP2 JP3
JP1 JP2 JP3
Figure 2. AcceleRAID 352 Default Jumper Identification (front)
Table 1. AcceleRAID 352 Default J um pe r Descriptions
JP1 Blank ROM mode; do not use JP2 Maintenance mode; do not use JP3 6-pin header
2 AcceleRAID 352 Quick Installation Guide
FAIL LED U1
Figure 3. AcceleRAID 352 Controller with LED (front)
Table 2. LED Description (front)
U1 FAIL LED
Hardware Installation
Manual No. DB11-00027-00 3
Performing an Installation
SE 1 SE 0 LVD 0 LVD 1
Figure 4. AcceleRAID 352 with LEDs and PIN Numbers (back)
Table 3. LED Descriptions (back)
SE 1 Single-ended LED, Channel 1 SE 0 Single-ended LED, Channel 0 LVD 0 LVD LED, Channel 0
PIN Nos.
654321
LVD 1 LVD LED, Channel 1
Table 4. Six-Pin Header Identification (JP3)
Pin 1 3.3V power Pin 2 Channel 0 SCSI activity Pin 3 Channel 1 SCSI activity Pin 4 Not used, not connected Pin 5 Cache Dirty and SCSI activity Pin 6 Ground pin
4 AcceleRAID 352 Quick Installation Guide
Hardware Installation

Installing the AcceleRAID 352 into the System Board

1. With the power off, plug the AcceleRAID 352 controller into an available 32-bit or 64-bit PCI slot on the system board (refer to Figure 5). The 32-bit slot is short, the 64-bit slot is longer.
Figure 5. Plugging the AcceleRAID 352 into a PCI Slot
2. Set the SCSI ID on each internal drive to a unique address between 0 and 15, but do not use address 7, as it is reserved for the controller. See the documentation that comes with your drives for instructions on how to do this.
Caution
If internal and external drives are used, be sure that no drive addresses are duplicated. External SCSI cabinets usually automatically assign drive addresses according to the drives’ location in the cabinet.
3. Disable termination on all SCSI drives connected to the controller. See the documentation that comes with your drives for instructions on how to do this. (Termination must be enabled on the last device, if applicable.)
4. Enable termination power on all SCSI drives connected to the controller. See the documentation that comes with your drives for instructions on how to do this.
Manual No. DB11-00027-00 5
Performing an Installation
5. Set the SCSI ID for each external disk drive to a unique address between 0 and 15, but do not use 7 (reserved for the controller). Do not duplicate SCSI IDs used by internal drives designated for the same channel. For more information on how to set SCSI IDs, refer to the disk drive documentation.
If you are using an external SCSI cabinet, see the Caution note above.
Figure 6. Connecting Internal and External Drives
6. Connect a wide, high-density, 68-pin SCSI ribbon cable to the internal SCSI connector on the AcceleRAID 352 controller and connect the other cable connectors to any SCSI devices as required (see Figure 6). Termination is automatic on the AcceleRAID 352.
7. Connect an active terminator to the end of the SCSI ribbon cable at the end farthest from the controller (see Figure 6).
External drive cabinets usually have termination built into the end of the SCSI bus. Check the documentation that comes with your drive cabinet to be sure this is the case. If not, use an active terminator at the end of the bus.
8. Connect a cable(s), with the 68 pin VHDCI, to either one or both of the external connector(s) on the AcceleRAID 352 controller. Connect the other end of the cable connector, to other devices or to a SAF-TE external drive cabinet, as required (see Figure 6).
6 AcceleRAID 352 Quick Installation Guide
Hardware Installation
Note
The AcceleRAID 352 terminator is ON by default. It is automatically terminated and will be disabled automatically if necessary.
An example of a typical, completed installation of the AcceleRAID 352 is shown in Figure 7.
T
T
System Board
Figure 7. AcceleRAID 352 in a Typical Installation
and SCSI Connectors
The hardware portion of the installation is complete. Please see the following section titled “What to Do Next”.

What to Do Next

1. Use RAID EzAssist to create an automatic or a custom RAID configuration.
Refer to the RAID EzAssist Configuration Utility Quick Configuration Guide or RAID EzAssist Configuration Utility User Reference Guide.
2. Install the AcceleRAID 352 controller drivers appropriate for your server’s network operating system.
Refer to the PCI Disk Array Controller Drivers Installation Guide and User Manual.
Manual No. DB11-00027-00 7
What to Do Next
8 AcceleRAID 352 Quick Installation Guide
LSI LOGIC CORPORATION
SOFTWARE LICENSE AND WARRANTY POLICY
Limited Warranty
LSI warrants to the original purchaser of the product enclosed herein (“Customer”) that (a) for a period of three (3) years from the date of Customer’s purchase of the Product (excluding batteries and memory) (the “Product Warranty Period”), and (b) for a period of one (1) year from the date of purchase of the Product by Customer (the “Battery/Memory Warranty Period”), the batteries and memory included in the Product will (i) be free from defects in workmanship and materials, and (ii) substantially conform to the documentation or other specifications for the Product. The limited warranties herein shall not apply to and shall be void for any Product that has been misused (including static discharge, improper installation, or accident), abused, modified, damaged a s a result of actions on the part of Customer or its agents or its processes, unauthorized service or parts, used in a manner inconsistent with normal computer operations (including but not limited to electrical irregularities, lightning or power line related damage, or other abnormal occurrences), or to normal wear and tear of the Product. The warranty herein is made to and for the benefit of the original purchaser of this Product and is non-transferable.
This warranty will not apply to, and LSI provides no warranty for any BIOS, software, ROM-based firmware or other product developed or manufactured b y an y third party whether including with this Product or not. Such warranty or warranties are provided by third parties and, to the extent permitted thereby, shall be made available and are hereby assigned by LSI to Customer.
Customer may obtain warranty service during the Product Warranty Period or Battery/Memory Warranty Period, as the case may be, if (a) Customer has contacted LSI at the telephone num ber listed LSI’s web site at www.lsilogic.com to obtain a Returned Material Authorization (“RMA”) number and appropriate instructions from LSI, (b) after obtaining LSI’s au thorization, Customer has returned the Product if so instructed to an authorized LSI service facility or to LSI in accordance
with LSI’s instructions and the terms of this Agreement, shipping costs to be borne by LSI, and (c) Customer has provided proof of purchase price and date for unregistered Product. LSI shall bear one-way shipping, packing and insurance costs and all other costs, excluding labor and parts, necessary to effectuate repair or replacement under this warranty. All Product repaired or replaced under this warranty shall be returned to Customer at Customer’s expense. Repair or replacement Product provided under this limited Product warranty will be furnished on an exchange basis and may be new or reconditioned. All Product returned under this warranty shall become the property of LSI. LSI shall notify Customer in the event that the Product returned under the warranty does not, in LSI’s sole determination, comply with the conditions and requirements set for th herein and, unless disposition instructions are given by Customer for the Product within thirty (30) days of such notification, the Product shall be returned to Customer freight collect.
Warranty Disclaimer EXCEPT AS SET FORTH IN THIS DOCUMENT, LSI MAKES NO
WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY REGARDING OR RELATING TO THE PRODUCT, OR ANY MATERIALS OR SERVICES FURNISHED OR PROVIDED TO OEM UNDER THIS AGREEMENT, INCLUDING MAINTENANCE AND SUPPORT. LSI SPECIFICALLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCT AND ANY OTHER MATERIALS AND SERVICES, AND WITH RESPECT TO THE USE OF ANY OF THE FOREGOING.
THE REMEDIES STATED IN THIS DOCUMENT CONSTITUTE CUSTOMER’S EXCLUSIVE REMEDIES AND LSI’S SOLE LIABILITY FOR BREACH OF THE LIMITED WARRANTIES SET FORTH HEREIN.
Software License Subject to the terms and conditions of this Agreement, LSI grants
Customer a non-exclusive, worldwide, non-transferable, revocable, royalty-free license to use, perform and display the LSI software that
is a part of the Product (“ LSI Software”) solely as par t of the Produc t incorporated into the OEM Products that and not on a standalone basis. Customer may not ( a) sell, lease, license, or sublicense the LSI Software, (b) de-compile, disassemble, reverse engineer, or otherwise attempt to derive source code from the LSI Software, in whole or in part, except to the extent such restriction is prohibited by applicable law, (c) modify or create derivative works from the LSI Software, or (d) use the LSI Software to provide processing services to third parties or otherwise use the LSI Software on a service bureau basis, electronically distribute or timeshare the LSI Software or market the LSI Software by interactive cable or remote processing services.
Limitation of Liability IN NO EVENT SHALL LSI’S TOTAL, CUMULATIVE LIABILITY
ARISING FROM THE SALE, USE AND DISPOSITION OF THE PRODUCT AND/OR THE LICENSING OF THE LSI SOFTWARE EXCEED THE AMOUNT PAID BY CUSTOMER FOR THIS PRODUCT. IN NO EVENT SHALL LSI BE LIABLE TO CUSTOMER OR ANY THE OTHER FOR ANY PUNITIVE, INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING LOSS OF PROFITS, INCURRED BY THAT PARTY, HOWEVER CAUSED AND UNDER ANY THEORY OF LIABILITY, WHETHER BASED IN CONTRACT, TORT (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE OR PRODUCT LIABILITY) OR WARRANTY, IN CONNECTION WITH THE SALE, USE AND DISPOSITION OF THE PRODUCT AND/OR THE LICENSING OF THE LSI SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Manual No. DB11-000027-00 08P5516
LSI Logic Corporation North American Headquarters Milpitas, CA
408.433.8000
Loading...