AVAGO HCPL 0500-000E Datasheet

Lead Coplanarity : 0.004 (0.10) MAX

0.202 (5.13)

Pin 1

0.019 (0.48)

0.182 (4.63)

0.021 (0.53)

0.011 (0.28)

0.050 (1.27)
TYP

0.244 (6.19)

0.224 (5.69)

0.143 (3.63)

0.123 (3.13)

0.008 (0.20)

0.003 (0.08)

0.010 (0.25)

0.006 (0.16)

SEATING PLANE

0.164 (4.16)

0.144 (3.66)

1

2

3

4 5

6

7

8

+

_

V

F1

V

CC

V

01

V

02

GND

V

F2

_

+

HCPL0530/HCPL0531/HCPL0534

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

DESCRIPTION

The HCPL05XX, and HCPL04XX optocouplers consist of an AlGaAs LED optically coupled to a high speed photodetector transis­tor housed in a compact 8-pin small outline package.

A separate connection for the bias of the photodiode improves the speed by several orders of magnitude over conventional
phototransistor optocouplers by reducing the base-collector capacitance of the input transistor. The HCPL04XX devices do not
have the base bonded out to a lead for additional noise margin. The HCPL053X devices have two channels per package for
optimum mounting density.

FEATURES

• High speed – 1 MBit/s

• 15kV/µs minimum commone mode
transient immunity at V

=1500V

CM

(HCPL0453/0534)

• Open collector output

• Guaranteed performance over
temperature: 0°C to 70°C

•U.L. recognized (File # E90700)

• VDE0884 recognized (file#136616)
– approval pending for HCPL0530/0531/0453
– ordering option V, e.g., HCPL0500V

• BSI recognized (file# 8661, 8662)
–HCPL0452/0500/0501 only

APPLICATIONS

• Line receivers

• Pulse transformer replacement

• Output interface to
CMOS-LSTTL-TTL

• Wide bandwidth analog
coupling

PACKAGE DIMENSIONS

NOTE

All dimensions are in inches (millimeters)

TRUTH TABLE
(positive logic)

LED

ON LOW

OFF HIGH

© 2004 Fairchild Semiconductor Corporation

V

O

Page 1 of 10

1

N/C

+

2

V

F

_

3

N/C

4 5

HCPL0500, HCPL0501

*BASE NOT CONNECTED

FOR HCPL0452, HCPL0453

V

8

CC

*

V

7

B

V

6

O

GND

5/3/04

/ ∆

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

(T

ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Value Units

Storage Temperature T

Operating Temperature T

Reflow Temperature Profile (Refer to page 9)

EMITTER

DC/Average Forward Input Current I

Peak Forward Input Current (50% duty cycle, 1 ms P.W.) I

Peak Transient Input Current - ([ ≤ 1 µs P.W., 300 pps) I

Reverse Input Voltage V

Input Power Dissipation P

DETECTOR

Average Output Current (Pin 6) I

Peak Output Current I

Emitter-Base Reverse Voltage (HCPL0500/HCPL0501 only) V

Supply Voltage V

Output Voltage V

Base Current (HCPL0500/HCPL0501 only) I

Output power dissipation P

= 25°C unless otherwise specified)

A

STG

OPR

(avg) 25 mA

F

(pk) 50 mA

F

(trans) 1.0 A

F

R

D

(avg) 8 mA

O

(pk) 16 mA

O

EBR

CC

O

B

D

-40 to +125 °C

-40 to +85 °C

5V

45 mW

5V

-0.5 to 30 V

-0.5 to 20 V

5mA

100 mW

(T

ELECTRICAL CHARACTERISTICS

= 0 to 70°C Unless otherwise specified)

A

INDIVIDUAL COMPONENT CHARACTERISTICS

Parameter Test Conditions Symbol Device Min Typ** Max Unit

(I

= 16 mA, T

EMITTER

F

Input Forward Voltage (I

Input Reverse Breakdown Voltage (I

Temperature coefficient of forward
voltage

DETECTOR

(I

= 0 mA, V

Logic high output current

Logic low supply current

F

(I

= 0 mA, V

F

(I

= 0 mA, V

F

(I

F

= 16 mA, V

O

O

O

= V

= V

(V

= 16 mA) 1.8

F

= 10 µA) BV

R

(I

= 16 mA) ( ∆ V

F

= V

(T

A

CC

(T

A

CC

= Open)

O

CC

=25°C)

= 5.5

CC

V)

A

V

F

R

T

) All -1.6 mV/°C

F

A

All

All 5.0 V

All 0.001 0.5

1.45 1.7

=25°C)

I

= 15 V)
=25°C)

OH

All 0.005 1

= 15 V) All 50

= 15 V)

I

CCL

HCPL0452/3/

0500/1/4

HCPL0530/1 400

120 200 µA

V

µA

© 2004 Fairchild Semiconductor Corporation

Page 2 of 10

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

ELECTRICAL CHARACTERISTICS

(T

= 0 to 70°C Unless otherwise specified) (Continued)

A

INDIVIDUAL COMPONENT CHARACTERISTICS

Parameter Test Conditions Symbol Device Min Typ** Max Unit

(I

= 0 mA, V

F

V

= 15 V) (T

CC

Logic high supply current

(I

= 0 mA, V

F

TRANSFER CHARACTERISTICS

Parameter Test Conditions Symbol Device Min Typ** Max Unit

COUPLED

Current transfer ratio
(Note 1)

Logic low output voltage
output voltage

** All typicals at T

= 25°C

A

(I

= 16 mA, V

F

(V

CC

(I

= 16 mA, V

F

(I

= 16 mA, I

F

(V

CC

(I

F

(V

CC

(I

= 16 mA, I

F

(I

= 16 mA, I

F

= Open,

O

=25°C)

A

I

= Open)

O

(V

= 15 V)

CC

(T

= 0 to 70°C Unless otherwise specified)

A

CCH

HCPL0452/3/

HCPL0530/1/4 4

HCPL0500/0530 7 27 50

= 0.4 V)

= 4.5 V, T

= 4.5 V, T

= 16 mA, I

= 4.5 V, T

O

A

= 0.5 V)

O

(V

= 4.5 V)

CC

= 1.1 mA)

O

A

= 3 mA)

O

A

= 0.8 mA)

O

(V

= 4.5 V)

CC

= 2.4 mA)

O

(V

= 4.5 V)

CC

=25°C)

=25°C)

=25°C)

CTR

V

OL

HCPL0501/0531

HCPL0501/0534

HCPL0501/0531/4

HCPL0501/0531/4

All 0.01 1

0500/1

HCPL0452/3

HCPL0500 5 30

HCPL0452/3

HCPL0500 0.18 0.4

HCPL0530 0.5

HCPL0452/3

HCPL0500
HCPL0530

HCPL0452/3

19 27 50

15 30

0.25 0.4

0.13 0.5

0.23 0.5

µA

2

%

V

© 2004 Fairchild Semiconductor Corporation

Page 3 of 10

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

SWITCHING CHARACTERISTICS

(T

= 0 to 70°C unless otherwise specified., V

A

= 5 V)

CC

Parameter Test Conditions Symbol Device Min Typ** Max Unit

T

Propagation
delay time to
logic low

Propagation
delay time to
logic high

Common
mode
transient
immunity at
logic high

Common
mode
transient
immunity at
logic low

= 25°C, (R

A

T

= 25°C, (RL = 4.1 kΩ, IF = 16 mA) (Note 2) (Fig. 9)

A

(I

= 16 mA, VCM = 1500 V

F

(I

= 16 mA, TA = 25°C, VCM = 1500 V

F

= 4.1 k Ω , I

L

= 1.9 kΩ, IF = 16 mA) (Note 3) (Fig. 9)

(R

L

= 4.1 kΩ, IF = 16 mA) (Note 2) (Fig. 9) HCPL0500/0530 2.0

(R

L

(RL = 1.9 kΩ, IF = 16 mA) (Note 3) (Fig. 9)

= 16 mA) (Note 2) (Fig. 9)

F

T

= 25°C

A

T

HCPL0500/0530 0.45 1.5

HCPL0501/0531/4

PHL

HCPL0501/0531/4

HCPL0452/3

HCPL0452/3

0.45 0.8

HCPL0500/0530 0.5 1.5

= 1.9 kΩ, IF = 16 mA) (Note 3) (Fig. 9)

(R

L

= 4.1 kΩ, IF = 16 mA) (Note 2) (Fig. 9) HCPL0500/0530 2.0

(R

L

T

= 25°C

A

T

PLH

(RL = 1.9 kΩ, IF = 16 mA) (Note 3) (Fig. 9)

(I

= 0 mA, VCM = 10 V

F

(Note 4) (Fig. 10) T

(I

= 0 mA, VCM = 10 V

F

T

= 25°C, (RL = 1.9 kΩ)

A

, RL = 4.1 kV)

P-P

A

= 25°C

P-P

)

|CM

(Note 4) (Fig. 10)

, RL = 1.9Ω, TA = 25°C)

P-P

(note 4) (Fig. 10)

(I

= 16 mA, VCM = 10 V

F

(Note 4) (Fig. 10) T

(I

= 16 mA, VCM = 10 V

F

(T

= 25°C, RL = 1.9 kΩ)

A

, RL = 4.1 kΩ)

P-P

A

= 25°C

P-P

)

|CM

(Note 4) (Fig. 10)

, CL = 15pF)

P-P

(Note 4) (Fig. 10)

HCPL0452/3

HCPL0501/0531/4

HCPL0452/3

HCPL0501/0531/4

HCPL0500

HCPL0530

HCPL0452

|

HCPL0501/31

H

HCPL0534 15,000 40,000

HCPL0453 15,000 40,000

HCPL0500

HCPL0530

HCPL0452

|

HCPL0501/31

L

HCPL0534 15,000 40,000

HCPL0453 15,000 40,000

0.3 0.8

1,000 10,000

1,000 10,000

1,000 10,000

1,000 10,000

µs

1.0

µs

1.0

V/µs

V/µs

ISOLATION CHARACTERISTICS (T

= 0°C to +70°C Unless otherwise specified.)

A

Characteristics Test Conditions Symbol Min Typ** Max Unit

Input-Output Isolation Voltage (note 5, 6) (f = 60 Hz, t = 1.0 min) V

Isolation Resistance (note 5) (V

Isolation Capacitance (note 5) (V

** All typicals at T

© 2004 Fairchild Semiconductor Corporation

= 25°C

A

= 0 , f = 1.0 MHz)

I-O

= 500 V)

I-O

Page 4 of 10

(9)

(9)

ISO

R

ISO

C

ISO

2500 — — Vac

11

10

—— Ω

— 0.2 — pF

RMS

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

NOTES

1. Current Transfer Ratio is defined as a ratio of output collector current, I

2. The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1kΩ pull-up resistor.

3. The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and 5.6 kΩ pull-up resistor.

4. Common mode transient immunity in logic high level is the maximum tolerable (positive) dV
common mode pulse signal V
transient immunity in logic low level is the maximum tolerable (negative) dV
pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., V

5. Device is considered a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are shorted together.

6. 2500 VAC RMS for 1 minute duration is equivalent to 3000 VAC RMS for 1 second duration.

, to assure that the output will remain in a logic high state (i.e., VO>2.0 V). Common mode

CM

, to the forward LED input current, IF, times 100%.

O

/dt on the leading edge of the

cm

/dt on the trailing edge of the common mode

cm

<0.8 V).

O

© 2004 Fairchild Semiconductor Corporation

Page 5 of 10

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

TYPICAL PERFORMANCE CURVES

Fig. 1 Normalized CTR vs. Forward Current

1.2

1.0

0.8

0.6

0.4

NORMALIZED CTR

0.2

0.0

Normalized to:
IF = 16 mA

0.1 1 10 100

VO = 0.4 V
VCC = 5 V

= 25°C

T

A

IF - FORWARD CURRENT (mA)

Fig. 3 Output Current vs. Output Voltage

16

TA = 25°C
V

= 5 V

CC

14

12

10

8

6

4

- OUTPUT CURRENT (mA)

O

I

2

0

02468101214161820

VO - OUTPUT VOLTAGE (V)

I

= 40 mA

F

I

= 35 mA

F

I

= 30 mA

F

I

= 25 mA

F

= 20 mA

I

F

= 15 mA

I

F

I

= 10 mA

F

IF = 5 mA

Fig. 2 Normalized CTR vs. Temperature

1.2

1.0

0.8

0.6

0.4

NORMALIZED CTR

Normalized to:
TA = 25°C

0.2

0.0

-60 -40 -20 0 20 40 60 80 100

IF = 16mA
VCC = 5 V

= 0.4 V

V

O

TA - TEMPERATURE (°C)

Fig. 4 Logic High Output Current

vs. Temperature

1000

IF = 0 mA

= 5 V

V

CC

= 5 V

V

O

100

10

1

- LOGIC HIGH OUTPUT CURRENT (nA)

OH

I

0.1

-60 -40 -20 0 20 40 60 80 100

TA - TEMPERATURE (°C)

Fig. 5 Propagation Delay vs. Temperature

800

700

600

R = 4.1 K (TPLH)

L

500

400

300

200

- PROPAGATION DELAY (ns)
p

T

100

RL = 1.9 K (TPHL)

0

-60 -40 -20 0 20 40 60 80 100

= 4.1 K (TPLH)

R

L

RL = 1.9 K (TPLH)

TA - TEMPERATURE (°C)

© 2004 Fairchild Semiconductor Corporation

IF = 16 mA

= 5 V

V

CC

Page 6 of 10

Fig. 6 Propagation Delay vs. Load Resistance

10000

IF - 16 mA (TPHL)

IF - 10 mA (TPHL)

1000

IF - 16 mA (TPLH)

- PROPAGATION DELAY (ns)

P

T

100

1 10

IF - 10 mA (TPLH)

RL = LOAD RESISTANCE (kΩ)

VCC = 5 V
TA = 25°C

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

Noise
Shield

Pulse
Generator
tr = 5ns

Ω

Z = 50

O

10% D.C.
I/f < 100µs

I Monitor

F

Test Circuit for HCPL0452, HCPL0453, HCPL0500 and HCPL0501 Test Circuit for HCPL0530, HCPL0531 and HCPL0534

1

+

I

F

2

V

F

-

3

4

R

m

V

CC

8

V

B

7

V

O

6

5

GND

0.1 µF

R

L

+5 V

V

O

L

C = 1.5 µF

I

F

0

V

O

T

PHL

Pulse
Generator
tr = 5ns
Z = 50

Ω

O

10% DUTY CYCLE

I/f < 100µS

F

I

MONITOR

1.5 V

F

I

R

m

Noise

+

Shield

1

V

F1

-

2

-

3

F2

V
+

4 5

5 V

1.5 V
V

OL

T

PLH

8

7

6

Fig. 7 Switching Time Test Circuit

I

F

A

B

V

FF

Test Circuit for HCPL0452, HCPL0453, HCPL0500 and HCPL0501 Test Circuit for HCPL0530, HCPL0531 and HCPL0534

Noise
Shield

1

+

2

V

F

-

3

4

+-

Pulse Gen

V

CC

8

V

7

V

6

GND

5

V

CM

+5 V

B

R

L

O

V

O

0.1 µF

-

I

F

A

B

V

FF

Noise
Shield

+

1

V

F1

-

2

-

3

F2

V
+

4 5

+-

Pulse Gen

8

7

6

V

CM

V

V

V

GND

V

V

V

GND

CC

R

01

02

CC

R

01

02

+5 V

L

L

0.1 µF

0.1 µF

V

O

L

C = 1.5 µF

+5 V

V

O

Fig. 8 Common Mode Immunity Test Circuit

© 2004 Fairchild Semiconductor Corporation

V 10 V

CM

10% 10%

0 V

V

Switch at A : I = 0 mA

V

Switch at A : I = 16 mA

90%

t

r

O

F

O

F

Page 7 of 10

90%

t

f

5 V

V

OL

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

ORDERING INFORMATION

Option Order Entry Identifier Description

VVVDE 0884 (approval pending for HCPL0530, HCPL0531 & HCPL0534)

R1 R1 Tape and reel (500 units per reel)

R1V R1V

R2 R2 Tape and reel (2500 units per reel)

R2V R2V

MARKING INFORMATION

VDE 0884 (approval pending for HCPL0530, HCPL0531 & HCPL0534),
Tape and reel (500 units per reel)

VDE 0884 (approval pending for HCPL0530, HCPL0531 & HCPL0534),
Tape and reel (2500 units per reel)

1

0500

43

Definitions

1Fairchild logo

2Device number

VDE mark (Note: Only appears on parts ordered with VDE

3

option – See order entry table)

4 One digit year code, e.g., ‘3’

5Two digit work week ranging from ‘01’ to ‘53’

6 Assembly package code

2

SYYXV

5

6

© 2004 Fairchild Semiconductor Corporation

Page 8 of 10

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

Carrier Tape Specifications

8.0 ± 0.10

3.50 ± 0.20

8.3 ± 0.10

0.30 MAX

4.0 ± 0.10

2.0 ± 0.05
Ø1.5 MIN

1.75 ± 0.10

5.5 ± 0.05

12.0 ± 0.3

5.20 ± 0.20

Reflow Profile

300

250

200

150

100

Temperature (°C)

50

0

0

0.1 MAX

User Direction of Feed

245°C peak

Time above 183°C, 120–180 sec

Ramp up = 2–10°C/sec

0.5 1 1.5 2 2.5 3 3.5 4 4.5

Time (Minute)

6.40 ± 0.20

230°C, 10–30 s

Ø1.5 ± 0.1/-0

• Peak reflow temperature: 245°C (package surface temperature)

• Time of temperature higher than 183°C for 120–180 seconds

• One time soldering reflow is recommended

© 2004 Fairchild Semiconductor Corporation

Page 9 of 10

5/3/04

HIGH SPEED TRANSISTOR

OPTOCOUPLERS

Single Channel: HCPL0452 HCPL0453 HCPL0500 HCPL0501
Dual Channel: HCPL0530 HCPL0531 HCPL0534

DISCLAIMER

FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO
ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME
ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;
NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.

LIFE SUPPORT POLICY

FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES
OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR
CORPORATION. As used herein:

1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in a significant injury of the user.

2. A critical component in any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.

© 2004 Fairchild Semiconductor Corporation

Page 10 of 10

5/3/04